Valcom VIP-410 User Manual

Issue 1

Issue 2

VIP-410

ONE-WAY IP WALL SPEAKER

INTRODUCTION

The VIP-410 One-Way IP Wall Speaker enables
voice access to a single zone of one-way paging
over an IP-based LAN/WAN. This allows a page
zone extension anywhere on the network. The
speaker level is electrically adjusted during set up..
The enclosure is made of steel with a durable gray
powder coated finish. The color of the enclosure
can easily be changed to match any decor. A
detachable black clothe grille is included. The
speaker requires an 802.3af PoE compliant network
connection.

Power is provided to the VIP-410 via a Power over
an Ethernet switch meeting the 802.3af
specification.

INSTALLATION

FCC Information

This equipment has been tested and found to
comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference when the equipment is
operated in a commercial environment. This
equipment generates, uses and can radiate radio
frequency energy and if not installed and used in
accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential area
may cause harmful interference in which case the
user will be required to correct the interference at
his own expense.

DIMENSIONS/WEIGHT

 10.13” H x 12.31” W x 4.63” D
(25.73cm x 31.27cm W x 11.75cm D)
 Weight: 4.25 LBS (1.91 kg)

Environment

Temperature: 0 to +40° C
Humidity: 0 to 85% non-precipitating

1 947078

Precautionary Designations

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: To reduce the risk of electric shock,
Refer se rvic ing to qu alifie d serv ice pers onn e l.

Do not remove cover.

No user serviceable parts inside.

This symbol indicates that dangerous
voltage constituting a risk of electric
sho ck is pre s ent within this un it.

This symb o l indica tes that there are
imp o rtant op er ating a nd m a inte nance
instruction s in the lit erature accompanyin g

this unit.

Packing List

Qty. Item

1 VIP-410
1 VSP Document

MOUNTING

Remove the screw holding the mounting bracket to
the enclosure. Mount the bracket using appropriate
hardware such as # 8 pan head crews. After
making the required connections, reattach the
enclosure to the mounting bracket

Network Connection

The VIP-410 has one RJ-45 network connector on
the rear panel. Use a standard Ethernet patch cable
to connect the VIP-410 to Ethernet switch. See Fig.
1 for details.

Setup

Information specific to your application will need to
be programmed into the VIP-410 using a computer.
The PC used for the programming should be
connected to the same subnet as the VIP-410.
Setup will be done using the IP Solutions Setup
Tool. Download the latest version of the free IP

TECHNICAL ASSISTANCE

When trouble is reported, verify power is being
supplied to the unit and there are no broken
connections. If a spare unit is available, substitute
a spare unit for the suspected defective unit.

Assistance in troubleshooting is available from the
factory. Call [phone] and press 1 for
Technical Support or via email at
[e-mail]

When requesting assistance, you should include all
available information. It is strongly suggested that
you go to the web site and review the information at
www.valcom.com.

Valcom equipment is not field repairable. Valcom,
Inc. maintains service facilities in Roanoke, VA.
Should repairs be necessary, attach a tag to the
unit clearly stating your company name, address,
phone number, contact person and the nature of
the problem. Send the unit to:

Valcom, Inc.

Repair & Return Dept.

5614 Hollins Road

Roanoke, Va. 24019-5056

Solution Setup Tool from the Valcom web site at
www.valcom.com/vipsetuptool. .

Valcom, Inc. warrants its products only to the original purchaser, for its own use, to be free from defects in materials and workmanship under conditions of
normal use and service for a period of one year from the date of shipment. This Limited Warranty obligation shall be limited to the replacement, repair or refund
of any such defective device within the warranty period, provided that:

1. inspection by Valcom, Inc. indicates the validity of the claim;

2. the defect is not the result of damage, misuse or negligence after the original shipment;

3. the product has not been altered in any way or repaired by others and that factory sealed units are unopened (a service charge plus parts
and labor will be applied to units defaced or physically damaged);

4. freight charges for the return of products to Valcom are prepaid;

5. all units 'out of warranty' are subject to a service charge. The service charge will cover minor repairs (major repairs will be subject to
additional charges for parts and labor).

This Limited Warranty is in lieu of and excludes all other warranties, expressed or implied and in no event shall Valcom, Inc. be liable for any
anticipated profits, consequential damages, loss of time or other losses incurred by the buyer in connection with the purchase, operation,
maintenance, installation, removal or use of the product. The maximum liability of Valcom under this warranty is limited to the purchase price of the
specific Product covered by the warranty.

Disclaimer. Except for the Limited Warranty provided herein, the product is provided “as-is” without any warranty of any kind whatsoever including, without

limitation, any WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT.
This warranty specifically excludes damage incurred in shipment. In the event a product is received in damaged condition, the carrier should be notified

immediately. Claims for such damage should be filed with the carrier involved in accordance with the F.O.B. point.

VALCOM LIMITED WARRANTY

Headquarters:

Valcom, Inc.

5614 Hollins Road Roanoke, VA 24019-5056

Phone: [phone] FAX: [phone]

2 947078