Valcom V-D2425, V-D2440 Installation Manual
Installation Manual V1.03
V-D2425 and V-D2440 Digital Clock
Valcom, Inc.
5614 Hollins Road
Roanoke, VA 24019
540-563-2000 P.
540-362-9800 F.
www.valcom.com
V-D2425 and V-D2440 Wired Clock
Table of Contents
Table of Contents—2
Installation Instructions
Flush Mount 3
Flush Mount Installation—3
Wall Mount 4
Surface (Wall) Mount Installation—4
Double Mount 5
Metal Double Mount Installation—5
Plastic Surface (Wall) Mount Installation— 6
Wiring Information
Wiring and Jumper Settings 6
Plastic Surface (Wall) Mount Installation—7
2-Wire Digital Communication 7
Plastic Double Mount Installation—8
RS485 Communication 110V 8
Plastic Double Mount Installation—9
Plastic Double Mount Installation—10
Support
Frequently Asked Questions 9
Wiring and Jumper Settings—11
Troubleshooting 10
2 Wire Digital Communication Wiring Information—12
Troubleshooting—13
Frequently Asked Questions—14
Compliances—15
Valcom, Inc.
5614 Hollins Road
Roanoke, VA 24019
540-563-2000 P.
540-362-9800 F.
www.valcom.com
*manuals may change without prior notice
2
Installation Instructions
Flush Mount Installation
Valcom, Inc.
5614 Hollins Road
Roanoke, VA 24019
540-563-2000 P.
540-362-9800 F.
www.valcom.com
1. Mount the flush mount box into the wall.
2. Connect the ground wire into the flush mount box using the tooth lockwasher and the machine screw nut (included in the
kit).
3. Disconnect the red filter from the display panel.
4. Connect the wiring as shown on the wiring diagram.
5. IMPORTANT: If using a low voltage system (24 volt) make sure that the transformer is an isolated transformer.
6. Mount the display panel into the flush mount box using the four (4) black machine screws (#6, included in the kit). Make
sure the switches are on the right side.
7. Snap the red filter into the display panel.
3
Flush Mount Picture 2.5”
Flush Mount Picture 4.0”
Installation Instructions
Flush Mount Installation
Figure 1
Valcom, Inc.
5614 Hollins Road
Roanoke, VA 24019
540-563-2000 P.
540-362-9800 F.
www.valcom.com
H = 4.65”
W = 10.3”
Front View: Side View
Flush Mount Angled View:
D3 = .28”
D4 = 3.5”
H = 4.65”
Figure 2
Front View: Side View
Front view:
Flush Mount Angled View:
D3 = .28”
D4 = 3.5”
H = 7.5”
4
Installation Instructions
Surface (Wall) Mount Installation
Valcom, Inc.
5614 Hollins Road
Roanoke, VA 24019
540-563-2000 P.
540-362-9800 F.
www.valcom.com
1. Mount the wall mount box into the double gang box using four machine screws(#6-32) included in the kit.
2. Connect the ground wire into the flush mount box using the tooth lockwasher and machine screw nut (included in the kit).
3. Disconnect the red filter from the display panel.
4. Connect the wiring as shown on the wiring diagram.
5. IMPORTANT: If using a low voltage system (24 volt) make sure that the transformer is an isolated transformer.
6. Mount the display panel into the flush mount box using four (4) black machine screws (#6, included in the kit). Make sure
the switches are on the right side.
7. Snap the red filter into the display panel.
5
Loading...