Valcom V-D11025A, V-D11040A Installation And Programming Manual
Installation and Programming Manual V1.03
V-D11025A / V-D11040A Digital Clocks
Valcom, Inc.
5614 Hollins Road
Roanoke, VA 24019
540-563-2000 P.
540-362-9800 F.
www.valcom.com
V-D11025A/V-D11040A Digital Clocks
Table of Contents
Table of Contents—2
Flush Mount Installation—3
Flush Mount Installation—4
Surface (Wall) Mount Installation—5
Metal Double Mount Installation—6
Plastic Surface (Wall) Mount Installation—7
Plastic Surface (Wall) Mount Installation—8
Plastic Double Mount Installation—9
Plastic Double Mount Installation—10
Plastic Double Mount Installation—11
Wiring and Jumper Settings—12
V-D11025A/V-D11040A Slave Mode—13
59 Minute Correction—14
58 Minute Correction—14
National Time/Rauland—15
Dukane—15
Rauland Digital—16
Midnight Reset or Once a Day Pulse—16
Setting the Time on the Digital Clock—17
Programming the Digital Clock—17
Relay Output Selections—23
Frequently Asked Questions—24
Troubleshooting—25
Valcom, Inc.
5614 Hollins Road
Roanoke, VA 24019
540-563-2000 P.
540-362-9800 F.
www.valcom.com
*manuals may change without prior notice
2
Flush Mount Installation
Valcom, Inc.
5614 Hollins Road
Roanoke, VA 24019
540-563-2000 P.
540-362-9800 F.
www.valcom.com
1. Mount the flush mount box into the wall.
2. Connect the ground wire into the flush mount box using the tooth lockwasher and the machine screw nut (included in the
kit).
3. Disconnect the red filter from the display panel.
4. Connect the wiring as shown on the wiring diagram.
5. IMPORTANT: If using a low voltage system (24 volt) make sure that the transformer is an isolated transformer.
6. Mount the display panel into the flush mount box using the four (4) black machine screws (#6, included in the kit). Make
sure the switches are on the right side.
7. Snap the red filter into the display panel.
3
Flush Mount Picture 2.5”
Front View:
Side View
Flush Mount Picture 4.0”
Flush Mount Installation
Fig ure 1
Valcom, Inc.
5614 Hollins Road
Roanoke, VA 24019
540-563-2000 P.
540-362-9800 F.
www.valcom.com
H = 4.65”
W = 10.3”
Front View: Side View
Flush Mount Angled View:
D3 = .28”
D4 = 3.5”
H = 4.65”
Fig ure 2
Front view:
Flush Mount Angled View:
D3 = .28”
D4 = 3.5”
H = 7.5”
4
Surface (Wall) Mount Installation
Valcom, Inc.
5614 Hollins Road
Roanoke, VA 24019
540-563-2000 P.
540-362-9800 F.
www.valcom.com
1. Mount the wall mount box into the double gang box using four machine screws(#6-32) included in the kit.
2. Connect the ground wire into the flush mount box using the tooth lockwasher and machine screw nut (included in the kit).
3. Disconnect the red filter from the display panel.
4. Connect the wiring as shown on the wiring diagram.
5. IMPORTANT: If using a low voltage system (24 volt) make sure that the transformer is an isolated transformer.
6. Mount the display panel into the flush mount box using four (4) black machine screws (#6, included in the kit). Make sure
the switches are on the right side.
7. Snap the red filter into the display panel.
5
Metal Double Mount Installation
Valcom, Inc.
5614 Hollins Road
Roanoke, VA 24019
540-563-2000 P.
540-362-9800 F.
www.valcom.com
1. Screw hanger/mounting rod (included in the kit) into the crossbar (also included in the kit).
2. Insert wires through hanger/mounting rod.
3. Install crossbar using two (2) #6-32 screws into double gang box.
4. Mount the double mount box into the clock base using two (2) #6 nuts and Tooth Lockwasher #6. (The double mount can be
mounted either on the wall or on the ceiling).
5. Insert the two (2) locking hole plugs (0.187”) and the locking hole plug (0.562”) into the unused holes.
6. Insert double mount case onto the hanger/mounting rod.
7. Insert the support bracket onto the hanger/mounting rod.
8. Screw the two (2) nuts (included in the kit) onto hanger/mounting rod and secure the clock base to wall.
9. Connect the ground wire into the double mount box using the tooth lockwasher and machine screw nut (included in the kit).
10. Disconnect the red filter from the display panel.
11. Connect the wiring as shown on the wiring diagram.
12. IMPORTANT: If using a low voltage system (24 volt) make sure that the transformer is an isolated transformer.
13. Mount the display panel on one side of the double mount box using four (4) black machine screws (#6, included in the
kit). Make sure the switches are on the right side.
14. Snap the red filter into the display panel.
15. Repeat steps 9-13 for the second clock.
6
Plastic Surface (Wall) Mount Installation
Valcom, Inc.
5614 Hollins Road
Roanoke, VA 24019
q
540-563-2000 P.
540-362-9800 F.
www.valcom.com
y
t
r
w
e
7
Valcom, Inc.
5614 Hollins Road
Roanoke, VA 24019
540-563-2000 P.
540-362-9800 F.
www.valcom.com
Plastic Surface (Wall) Mount Installation
Mount Housing to Wall and/or Gang Box - To mount the housing to the wall, drive two (2) plastic anchors into the wall (not
q
supplied in kit) and take two pan head screws (also not supplied in kit) and drive them into the plastic inserts leaving an 1/8th inch
gap between the head of the screw and the wall. Mount the housing to the wall by lining up the two holes in the back of the top of
the housing with the two screws with the 1/8 inch gap from the wall and slide the housing onto the heads of the screws. To mount the
housing to the gang box, take the four (4) 6-32 x 1” screws (supplied in kit) and screw them through the four holes in the center of the
inside of the housing and the four holes in the gang box.
Note: If using a metal gang box, a ground must be provided to the gang box.
Feed Wiring Into the Housing - Take the wire coming from the inside of the gang box and feed it through the hole in the middle of
w
the housing.
Plug and Secure Wiring - Loosen the provided wire clamp (comes attached to the inside of the housing) and slip excess wiring
e
through and tighten the clamp. After securing excess wiring, plug the jack at the end of the wiring into the appropriate jack on the back
of the display board.
Mount Display Board to Housing - Using the four (4) self tapping, 6-19 x 1/2” flat head screws supplied in the assembly kit, take
r
the display board and screw it to the front side of the clock housing (4 screws per clock).
Snap on Filter - Take the red filter bezel and snap it on to the front side of the housing.
t
Snap on Frame - Take the gray frame and snap it on to the front side of the housing.
y
8
Loading...