Valcom V-5330100, V-5330200 Service Manual
PagePac
Back Box (Optional)
Volume Control
®
by
P-TEC VOICE PAGING SPEAKERS
V-5330100 (VOICE COIL)
V-5330200 (70 VOLT)
INTRODUCTION
P-TEC Voice Paging Speakers are suitable for
voice paging as well as background music. The
V- 5330200 is a 70 volt model with adjustabl e taps
and volume control. The V - 5330100 is a voice coil
(45 Ohm) 3.4 volt model with volume control.
P-TEC speakers consist of a 3.6 inch cone
speaker mounted in a unique surface-mount baffle. The baffle is designed for mounting on
acoustic tile, such as those normally found in suspended-ceilings; and can be mounted without
cutting large holes in the tile. The mounting pins
can be removed for mounting in a hard ceiling.
The speaker housing has screw holes for securing
speaker without mounting pins. Although the
P-TEC speakers are designed especially for standard suspended ceilings, they can be used on
many types of ceiling materials.
Issue 2
DIMENSIONS/WEIGHT
• 8”Dia. x 2.5”D (20.32cm x 6.35cm)
Voice Coil .75 lbs. (.34 kg)
70 Volt 1.25 lbs. (.56 kg)
INSTALLATION
Selecting the Power-Tap Wire (70V)
Note: For the V-5330100 Speakers (Voice Coil),
begin at Suspended Ceiling Installation.
1. Remove the Quick-Connect connector from
the accessory pack.
2. Select the desired power-tap wire:
Yellow = 1/4W
Red = 1/2W
Green = 1W
White = 2W
Blue = 4W
Note: Refer to spacing chart (Fig ure 6) for re com-
mended speaker spacing.
Figure 1. P-TEC Paging Speaker (70V shown)
3. Install the Quick-Connect connector on the
wire. Use pliers to close the connector over
the wire. The connector can be removed by
prying it open with a screwdriver, and can be
reused several times (see Figure 2).
Reusable
Quick-Connect
Connector
Tap Wire
Figure 2. Attaching the Reuseable Quick-Connect
Connector (V-5330200 Only)
1947165
4. Connect the power-tap wire to the gold (+)
Q
Gold ( + )
To Paging
Amplifier
To Next
Speaker
terminal (see Figure 3).
5. Arrange the unused power-tap wires neatly
inside the speaker housing and tape them to
the inside of the housing.
( - ) Silver
4. If necessary, adjust paging volume after installation. The volume control is located on the
side of the speaker. Use a small screwdriver t o
turn the control.
5. Install the volume control cover found in th e
accessory pack.
( + ) Gold
Black - Common
(Connected at Factory)
70V Transformer
Reusable
uick-Connect
Connector
Arrange unused wires
neatly inside speaker housing.
Power Tap Wires
Power Tap Wires
Yellow - 1/4 Watt
Yellow
Red - 1/2 Watt
Red
Green - 1 Watt
Green
White - 2 Watt
White
Blue - 4 Watt
Blue
Tap Wire
- 1/4 Watt
- 1/2 Watt
- 1 Watt
- 2 Watt
- 4 Watt
Figure 3. Connecting the Tap Wire
(V-5330200 Only)
Suspended Ceiling
Note: Wrap wires around strain relief posts so
speaker wires will not pull free.
1. Lift the adjacent ceiling tile and slide it out of
the way.
2. Install the speaker by inserting the mounting
pins through the ceiling tile, and hold the
speaker in place.
3. Place the wire and washers, and speaker
mounting clips over mounting pins (so pins
slide through clips).
To
Amplifier
Red
Gold
Spike
Use mounting holes and screws
when spikes can not be used.
Black
Silver
Spike
Figure 4. P-TEC Installation
Note: When using a PagePac
®
Amplicenter,
music volume should be adjusted at the
paging amplifier or music source. Adjust
paging before adjusting background music.
Maintain Speaker Phasing
When using multiple speakers in a single run,
keep speakers in phase by connecting the
speaker wires to the same spike on each speaker
(either wire can connect on either spike, as long
as the pattern is followed on each speaker) . The
gold spike is the plus (+) terminal (see Figure 5).
Figure 5. Maintaining Speaker Phasing
Handling Shielded Speaker Cable
V-5330200 Only
If you are using shielded speaker cable, splice the
shield wire at the speaker location so a continuous shield is maintained. When connecting a single speaker, or the last speaker on the run, clip
the shield wire where it emerges from the outer
insulation on the speaker cable.
TECHNICAL ASSISTANCE
When calling, have a VOM and a telephone test
set available and call from the job site. Call (540)
427-3900 and ask for PagePac Technical Support, or call (540) 427-6000 for Valcom 24-hour
Automated Support or visit our websites at
http://www.pagepac.com and www.valcom.com.
Note: Washers provide isolation from the pins if
the back of the tile is covered with metal
foil.
2947165
Loading...