Valcom IP Solutions VIP-483 User Manual

Issue 3

VIP-483

Vandal Resistant IP FlexHorn

INTRODUCTION

The VIP-483 Vandal Resistant IP FlexHorn
enables loudspeaker voice paging anywhere on
an Ethernet network. The VIP-483 consists of a
high efficiency Class-D Horn and a Network
Interface, allowing stand alone capability when
used with a SIP telephone system or can be
accessed from a variety of Valcom managed
VoIP products. Power is provided to the VIP-483
via a Power over Ethernet (PoE) switch meeting
the 802.3af specification.

SPECIFICATIONS

Access Methods

 SIP telephone system
 PBX, FXO Port w/VIP-811
 POTS telephone set w/VIP-811
 PBX, FXS Port w/VIP-821
 Valcom M Cast Page Group

Features

 RJ-45 for network connection
 Network activity LEDs
 Power over Ethernet (PoE) 802.3af

compatible

 Vandal Resistant stainless steel faceplate

Dimensions/Weight

 8.5” H x 11.0" W x 4.25" D
(21.6cm H x 27.9cm W x 10.8cm D)
 Weight: 3.5 lbs. (1.6 kg)

Nominal Power Requirements

Via 802.3af (PoE) Ethernet Switch: Class 3

Environment

Temperature: 0 to +40° C
Humidity: 0 to 85% non-precipitating

Packing List

Qty Item

1 VIP-483 IP FlexHorn
1 VSP Document

Precautionary Designations

CAUTION: To reduce the risk of electric shock,

Refer servicing to qualified service personnel.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

Do not remove cover.

No user serviceable parts inside.

This symbol indicates that dangerous
voltage constituting a risk of electric
shock is present within this unit.

This symbol indicates that there are
important operating and maintenance
instructions in the literature accompanying
this unit.

1 947349

FCC Information

This equipment has been tested and found to
comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide
reasonable protection against harmful
interference when the equipment is operated
in a commercial environment. This
equipment generates, uses and can radiate
radio frequency energy and if not installed
and used in accordance with the instruction
manual, may cause harmful interference to
radio communications. Operation of this
equipment in a residential area may cause
harmful interference in which case the user
will be required to correct the interference at
his own expense.

INSTALLATION

Operation

The VIP-483 provides IP loudspeaker paging
access via network connection to customer
telephone system or stand alone telephone set.
Interface to customer telephone system can be
via SIP registration, FXO or FXS port (with
appropriate PBX connection and Valcom
VIP-81x/82x).

Mounting

The VIP-483 is designed for flush mounting on a
hollow surface or to a Valcom backbox. Using
Figure 1 as a guide, cut a hole in the mounting
surface large enough to allow recessing the
FlexHorn into the wall. Next, drill mounting holes
in the surface to align with the four mounting
holes in the stainless steel grille. Using
appropriate anchors and screws (not included),
mount the VIP-483 to the surface. Alternatively,
Valcom backbox model VB-R16 is available for
mounting this model.

Power Connections

The only method of powering a VIP-483 Network
Interface is via a Power over Ethernet (PoE)
network switch or power injector meeting the

802.3af specification.

Network Connection

The VIP-483 has one Ethernet network connector
on the circuit board. Use a standard Ethernet
patch cable to connect the Ethernet connector of
the VIP-483 to an Ethernet switch.

Signal Connections

Signal connections from the network interface to
the FlexHorn are pre-wired at the factory.
No further connections are required.

Status Indicator Lights

The VIP-483 Network Interface has 2 status
indicator lights on the RJ-45 Ethernet connector.
One LED (left corner) indicates Link when lit, the
other LED flashes to indicate network activity.

Setup

Information specific to your application will need
to be programmed into the VIP-483 using a
computer. The PC used for programming should
be connected to the same subnet as the VIP-483.

Setup will be done using the IP Solutions Setup
Tool. The IP Solutions Setup Tool may be
downloaded from the Valcom web site at
http://www.valcom.com.

TECHNICAL ASSISTANCE

Assistance in troubleshooting is available from
the factory. Call [phone] and press 1 for
Technical Support or via email at
[e-mail].

When requesting assistance, you should include
all available information. It is strongly suggested
that you go to the web site and follow the trouble
resolution procedure at http://www.valcom.com.

Valcom equipment is not field repairable.
Valcom, Inc. maintains service facilities in
Roanoke, VA. Should repairs be necessary,
attach a tag to the unit clearly stating your
company name, address, phone number, contact
person and the nature of the problem. Send the
unit to:

Valcom, Inc.

Repair & Return Dept.

5614 Hollins Road

Roanoke, Va. 24019-5056

2 947349

FIGURE 1. MOUNTING

Valcom, Inc. warrants its products only to the original purchaser, for its own use, to be free from defects in materials and workmanship under conditions of
normal use and service for a period of one year from the date of shipment. This Limited Warranty obligation shall be limited to the replacement, repair or refund
of any such defective device within the warranty period, provided that:

1. inspection by Valcom, Inc. indicates the validity of the claim;

2. the defect is not the result of damage, misuse or negligence after the original shipment;

3. the product has not been altered in any way or repaired by others and that factory sealed units are unopened (a service charge plus parts
and labor will be applied to units defaced or physically damaged);

4. freight charges for the return of products to Valcom are prepaid;

5. all units 'out of warranty' are subject to a service charge. The service charge will cover minor repairs (major repairs will be subject to
additional charges for parts and labor).

This Limited Warranty is in lieu of and excludes all other warranties, expressed or implied and in no event shall Valcom, Inc. be liable for any
anticipated profits, consequential damages, loss of time or other losses incurred by the buyer in connection with the purchase, operation,
maintenance, installation, removal or use of the product. The maximum liability of Valcom under this warranty is limited to the purchase price of the
specific Product covered by the warranty.

Disclaimer. Except for the Limited Warranty provided herein, the product is provided “as-is” without any warranty of any kind whatsoever including, without

limitation, any WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT.
This warranty specifically excludes damage incurred in shipment. In the event a product is received in damaged condition, the carrier should be notified

immediately. Claims for such damage should be filed with the carrier involved in accordance with the F.O.B. point.

VALCOM LIMITED WARRANTY

Headquarters:

Valcom, Inc.

5614 Hollins Road Roanoke, VA 24019-5056

Phone: [phone] FAX: [phone]

3 947349