Issue 1
Issue 2
VIP-431-DS
IP TALKBACK WALL SPEAKER/CLOCK ASSEMBLY
INTRODUCTION
The VIP-431-DS IP Talkback Wall Speaker with
Digital Clock enables two-way handsfree voice
access to a single location over an IP-based
network. This allows a page zone extension
anywhere on the network. The speaker audio level
is electronically adjusted via software. Clock
synchronization is acquired from a Network Time
Protocol (NTP) server, either a private internal
server or from the Internet. A call switch input is
provided for call initiation. The enclosure is made
of steel with a durable gray powder coated finish
and features an angled design to direct sound
downward. The color of the enclosure can easily
be changed to match any decor. A detachable
black cloth grille is included. Power is provided to
the VIP-431-DS via a Power over Ethernet (PoE)
switch meeting the 802.3af specification.
SPECIFICATIONS
Access Methods
PBX, FXO Port using a VIP-811
POTS telephone set using a VIP-811
PBX, FXS Port using a VIP-821
Valcom M Cast Page Group
SIP–enabled telephone system
Features
RJ-45 network connection
802.3af compatible
High Efficiency Class-D Amplifier
Network Time Protocol (NTP) synchronization
INSTALLATION
FCC Information
This equipment has been tested and found to
comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference when the equipment is
operated in a commercial environment. This
equipment generates, uses and can radiate radio
frequency energy and if not installed and used in
accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential area
may cause harmful interference in which case the
user will be required to correct the interference at
his own expense.
DIMENSIONS/WEIGHT
15.0” H x 12.25” W
4.0” D (top) 1.45” D (bottom)
(38.1cm H x 31.1cm W
10.2cm D (top) 3.7cm (bottom)
Weight: 4.25 LBS (1.91 kg)
Environment
Temperature: 0 to +40° C
Humidity: 0 to 85% non-precipitating
Precautionary Designations
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: To reduce the risk of electric shock,
Refer se rvic ing to qu alifie d serv ice pers onn e l.
Do not remove cover.
No user serviceable parts inside.
This symbol indicates that dangerous
voltage constituting a risk of electric
sho ck is pre s ent within this un it.
This symb o l indica tes that there are
imp o rtant op er ating a nd m a inte nance
instruction s in the lit erature accompanyin g
this unit.
1 947793
NETWORK
CONNECTION
Packing List
Qty. Item
1 VIP-431-DS
1 VSP Document
MOUNTING
Remove the screw holding the mounting bracket to
the enclosure. Mount the bracket using appropriate
hardware such as #8 pan head crews. After
making the required connections, reattach the
enclosure to the mounting bracket
SPEAKER CONNECTION DETAILS
LED (+)
LED (-)
IP TALKBACK
CONNECTS TO SPEAKER
OUT ON POWER FAIL
P6
P5P3P2P4
CALL SWITCH
SPEAKER OUT
NETWORK
-10 dB LINE
LEVEL OUT
MOUNTING
BRACKET
Figure 1. Connections
Network Connection
The VIP-431-DS has one RJ-45 network connector
on the rear panel. Use a standard Ethernet
patch cable to connect the VIP-431-DS to an
Ethernet switch. (See Figure 1)
Call Switch Connection
The VIP-431-DS provides a call switch input via
screw terminal connections. See Figure 1 for
detailed connections.
LED (+) and (-) Connection
LED (+) and (-) is a current limited output designed
to illuminate an optional LED. The LED is intended
to provide visual indication of call progress. The
LED illumination will flash when the call switch is
pressed and will continue to flash until the call is
answered. The LED illumination will be solid while a
connection to the VIP-431-DS is established.
-10 dB Line Level Out Connection
The -10dBm Line Level Out may be connected to
up to 40 Valcom Self Amplified Speakers in order to
provide additional sound reinforcement in an area.
Setup
Information specific to your application will need to
be programmed into the VIP-431-DS using a
computer. The PC used for programming should be
connected to the same subnet as the VIP-431-DS.
Setup will be done using the IP Solutions Setup
Tool. Download the latest version of the free IP
Solutions Setup Tool from Valcom web site at
www.valcom.com/vipsetuptool.
TECHNICAL ASSISTANCE
When trouble is reported, verify power is being
supplied to the unit and there are no broken
connections. If a spare unit is available, substitute
a spare unit for the suspected defective unit.
Assistance in troubleshooting is available from the
factory. Call (540) 563-2000 and press 1 for
Technical Support or via email at
support@valcom.com
When requesting assistance, you should include all
available information. It is strongly suggested that
you go to the web site and review the information
provided at http://www.valcom.com.
Valcom equipment is not field repairable. Valcom,
Inc. maintains service facilities in Roanoke, VA.
Should repairs be necessary, attach a tag to the
unit clearly stating your company name, address,
phone number, contact person and the nature of
the problem. Send the unit to:
Valcom, Inc.
Repair & Return Dept.
5614 Hollins Road
Roanoke, Va. 24019-5056
2 947793
Loading...