Thank you for purchasing a quality VALCO BABY product. Please read and follow the instructions outlined in
this guide carefully. Familiarise yourself with the construction and safety features; be sure that you understand
all the warnings and safety guidelines before use.
Important: Please read the following instructions carefully before assembling this product. Retain this
guide in a safe place for future reference.
PRODUCT REFERENCE GUIDE
Due to our policy of continuous product
development, this product is constantly
evolving. It is possible that some features or
procedures outlined here have changed since
this document was written. If you are unsure
of any procedure shown here, please contact
us via the web at info@valco.com.au to obtain
the most up to date information before use.
Include the batch number, which can be found
on a sticker on the frame.
All pictures and diagrams herein are provided
for illustration purposes only.
Actual product, colour or fabric may vary.
VALCO BABY reserves the right to modify or
alter any specication or colour without notice
or obligation to modify any product previously
purchased
JOEY
TODDLER SEAT FOR
ZEE TWO
FURTHER INFORMATION
In North America only
www.valcobaby.com
1800 610 7850
© Copyright VE 2013240113
Suitable for Zee Two
USA Model No: ZTT0649
Weight limit: 20kgs
A
YOUR JOEY SEAT REQUIRES SOME
ASSEMBLY BEFORE USE:
FIGURE A
1. Remove Joey toddler
seat from the carton and
dispose of any packaging
thoughtfully.
2. The Joey comes in two parts,
the main seat section and a
back support bar.
Illustration only
Actual product may vary.
FIGURE B
3. Align the back support bar with the corresponding tubes
of the seat back. Be sure the buttons on the support bar
face the same side as the corresponding holes on the
seat tube.
4. Insert the back support bar into the tube. Depress
each button while pushing down on the bar, inserting it
further into the seat tubes until the buttons pop into the
button holes on the housing.
NOTE: FOR SAFETY REASONS THE SUPPORT BAR IS A TIGHT
FIT AND YOU MAY NEED TO PUSH HARD TO SEAT THE BAR INTO
POSITION CORRECTLY
FIGURE C
5. Pull the fabric of the seat back up and over the back
support bar.
6.
Work the fabric
over the back support bar until it ts
snugly into position.
NOTE: THE FABRIC WILL BE A TIGHT FIT AND WILL REQUIRE
EFFORT TO FIT IN PLACE.
7. Pull the side armrest aps over the metal frame and
secure with the snaps.
IMPORTANT WARNING: ALWAYS TEST THAT ALL BUCKLES,
SNAPS AND CLAMPS ARE SECURELY ENGAGED BEFORE USE.
JOEY ASSEMBLY/OPENING
FIGURE D
8. Remove Joey toddler seat from the carton and dispose
of any packaging thoughtfully.
9. Remove the bumper bar from the nylon housing at
either side of the stroller frame by pressing each inner
“release button” and pulling the bar upward (refer to
your stroller guide)
.
TO ATTACH THE SEAT
FIGURE E
10. Position the Joey toddler seat in the center of the
stroller and slot the clip foot over the front bar of the
stroller footrest. Be sure that the Joey seat faces forward
on the stroller.
11. Gently push down on the clip foot to secure the clip
foot onto the bar.
IMPORTANT WARNING: ALWAYS TEST THAT ALL BUCKLES/
CLAMPS ARE SECURELY ENGAGED BEFORE USE.
FIGURE C
12. Insert the bar ends into the nylon housing located on
either side of the frame. Be sure that the bar is securely
engaged in both sides.
E
B
C
!
!
D
2
J
USING YOUR HARNESS
FIGURE G
Your stroller harness is specically designed with many
built in safety features. This includes the requirement
that, when opened, all straps are released so that no
dangerous loops can be formed causing a strangulation
hazard.
WARNING: YOUR CHILD MUST ALWAYS
BE HARNESSED WHEN IN THE STROLLER
Closing your harness:
16. Slide each of the shoulder strap bottom guides (a) into
the corresponding channel on the top of each side strap
prong.
17. Insert each completed prong into the central buckle
housing (b).
Carefully adjust the harness straps to snugly
t your child by adjusting the sliders (c & d)
located on each strap. The harness should
be tted to your child’s body, tight enough
so that they cannot wriggle free of the straps
but, loose enough, so as not to cause any
discomfort.
Opening your harness:
18. Press the central housing button (e).This
will release both side prongs from the central
housing. The shoulder and waist straps will
release automatically from each other.If the
shoulder and waist straps do not automatically
disengage from each other, manually slide the
guides of the waist channels. Your harness will
separate into 5 sections.
IMPORTANT WARNING: WHEN NOT IN USE, BE SURE THE
SHOULDER AND WAIST STRAPS ARE ALWAYS DISCONNECTED
FROM THE CENTRAL HOUSING AND EACH OTHER.
a
b
c
e
d
!
!
!
F
G
TO REMOVE THE SEAT
FIGURE F
13.To remove the seat: Feeling the side of the nylon
housing that sits below the frame at each side (facing
inward), locate the release button in the side housing
FIGURE G
14. Press the release button inward while simultaneously
lifting upward on the housing. Repeat for the other side
and lift the seat free from the stroller.
15. Lift the seat free from the stroller. The clip foot will
automatically disengage.
IMPORTANT WARNING: ALWAYS TEST THAT ALL BUCKLES AND
CLAMPS ARE SECURELY ENGAGED BEFORE USE.
FOLDING YOUR STROLLER
The Joey Seat for Zee Two cannot be folded with your
stroller. Remove the seat as outlined in Fig. F, prior to
folding your stroller.
WARNING
• FOLLOW THE MANUFACTURER’S INSTRUCTIONS.
• PUT ON ALL THE BRAKES WHENEVER YOU PARK THE PRAM/STROLLER.
• DO NOT LEAVE CHILDREN UNATTENDED.
• DO NOT CARRY EXTRA CHILDREN OR BAGS ON THIS PRAM/STROLLER.
• MAKE SURE CHILDREN ARE CLEAR OF ANY MOVING PARTS IF YOU ADJUST THE PRAM/
STROLLER. OTHERWISE THEY MAY BE INJURED.
Remember, your child’s safety is your responsibility...
• NEVER USE ON STAIRS OR ESCALATORS.
• AlwAys use the tether strAp when the stroller is in use.
• the CorreCt use AnD MAintenAnCe oF this VehiCle Are essentiAl.
• Be sure thAt All ClAMps AnD BuCkles Are seCurely FixeD AnD in plACe BeFore use
• when in the stroller, your ChilD Must AlwAys weAr the sAFety hArness, CorreCtly
FitteD AnD ADjusteD, At All tiMes.
• the MAxiMuM weight oF the oF the toDDler in this seAt is 20 kg’s.
• the optiMuM MAnoeuVrABility oF your stroller, pArtiCulArly when useD with the
joey seAt, is only AChieVeD when the tyres Are Fully puMpeD to the optiMAl operAting
pressure. (40 p.s.i.)
• neVer reMoVe your hAnDs FroM the stroller hAnDle while your ChilD is in the joey
SEAT.
• CheCk All pArts BeFore use For BreAkAge or FAtigue. DisContinue use iMMeDiAtely iF
ANY PART IS FOUND TO BE DAMAGED OR BROKEN.
• AlwAys plACe your ChilD into the joey seAt. neVer Allow your ChilD to CliMB into or
OUT OF THE SEAT.
neVer leAVe the stroller At rest (pArkeD) with A toDDler in the joey seAt.
• neVer use this seAt iF the ChilD is unwilling to sit in it.
• AlwAys Be AwAre oF your ChilD’s position when sitting in the joey seAt. exCessiVe
leAning to one siDe or while the stroller is Cornering, MAy CAuse the unit to BeCoMe
UNSTABLE.
• extrA CAre Must Be tAken when using on uneVen surFACes.
• not reCoMMenDeD For A ChilD unDer 6 Months olD
• Do not use this seAt with Any other MoDels oF prAM/strolerr
• AlwAys ensure thAt eACh ChilD is CleAr oF All MoVing pArts when ADjusting the
STROLLER.
• when in the stroller eACh ChilD Must AlwAys weAr the sAFety hArness, CorreCtly
FitteD AnD ADjusteD, At All tiMes.
• AlwAys Be AwAre oF the risks proViDeD By Fire AnD other signiFiCAnt sourCes oF heAt
suCh As rADiAtors, etC. whiCh MAy Be in the iMMeDiAte ViCinity oF your stroller.
• it MAy Be unsAFe to use Any ACCessories other thAn VAlCo BABy ApproVeD ones.
• this proDuCt is intenDeD For DoMestiC use only. it is not intenDeD For CoMMerCiAl
USE.
Should the chassis become wet, dry off promptly before storing. If this pram is used near the ocean or salted roads, spray the chassis and seat
frame with water and dry. We recommend a rust inhibiting product should be used to prevent rust and fatigue on metal parts.
We recommend that you wipe down axles and lubricate the wheels every 3 months. Sand and dirt can grind down axles, if you live near the beach
or in a dusty environment you must wipe down the axles and wheels then lubricate them monthly.
AXLES ARE BEST LUBRICATED WITH GREASE OR PETROLEUM JELLY. MOVING PARTS ARE BEST LUBRICATED WITH SILICONE BASED PRODUCTS. DO
NOT USE OIL BASED PRODUCTS.
FURTHER INFORMATION
In North America only
www.valcobaby.com
1800 610 7850
!
Loading...