Thank you for purchasing a quality VALCO product. Please read and follow the instructions outlined in this
guide carefully. Familiarise yourself with the construction and safety features; be sure that you understand all
the warnings and safety guidelines before use.
Retain this guide in a safe place for future reference.
Important: Please read the following instructions carefully before assembling this product. Retain this guide in
a safe place for future reference.
PRODUCT REFERENCE GUIDE
TWIN TODDLER SEAT
© Copyright VE 2008
Due to our policy of continuous product
development, this product is constantly
evolving. It is possible that some features or
procedures outlined here have changed since
this document was written.
If you are unsure of any procedure shown
here, please contact us via the web at
info@valco.com. au or
info@valcobaby.com in North America,
to obtain the most up to date information
before use. Include the batch number, which
can be found on a sticker on the frame.
All pictures and diagrams herein are provided
for illustration purposes only. Actual product,
colour or fabric may vary. VALCO reserves the
right to modify or alter any specication or
colour without notice or obligation to modify
any product previously purchased
FURTHER INFORMATION
In Australia/New Zealand
www.valco.com.au
www.valco.co.nz
In North America only
www.valcobaby.com
1800 610 7850
TWIN TODDLER SEAT
TO INSTALL YOUR TWIN
TRI-MODE TODDLER SEAT:
(THE EASY WAY!)
FIGURE A
1. Before you begin to install the toddler
seat make sure to remove the bumper bar
or nylon plugs from the housing on the
stroller frame.
To do so: From the underside of the nylon
housing, feel the side of the nylon housing
that sits below the frame at each side of the
stroller (the place where the bumper bar
connects to the stroller).
2. Locate the center release “button.” (1)
3. Press the release button inward while
simultaneously pushing upward on the bar
or plug.
4. Repeat for the other side.
NOTE: TO AVOID FINGER ENTRAPMENTS,
THE NYLON PLUGS MUST BE
RETAINED AND INSTALLED WHEN THE
BUMPER BAR OR TODDLER SEAT IS NOT
IN USE.
FIGURE B
5. Remove the toddler seat from the box.
Your toddler seat will come folded at and
compact.
FIGURE C
6. Open the seat up by pulling the seat
back away from the ‘U’ shaped metal bar.
A
C
B
1
1
Remove Bumper Bar or Plugs
Bumper Bar
Nylon Plug
press
1
FIGURE D
7. Locate the swivelling mini rod, located on
each side of the toddler seat.
FIGURE E
8. Simultaneously rotate both mini rods,
and the ‘U’ shaped metal bar, so that they
meet.
9. Insert the ‘U’ legs into the nylon housings
of the mini rods until you feel them click
into place.
NOTE: UNTIL YOU HEAR A CLICK, THE BAR
IS NOT SECURE.
FIGURE F
10. You Toddler Seat is now fully
assembled.
11.Insert the seat connectors into the
housings on either side of your stroller (the
place where the bumper bar goes).
12. Once secured, slightly lift up the toddler
seat to ENSURE each leg has fully engaged
in each housing.
E
F
CLICK
D
2
FIGURE G
13. Your toddler seat is now attached to
the stroller and should look like this.
FIGURE H
14. Check the underside of the footrest for
a ‘D’ shaped metal ring.
NOTE: IF YOU CANNOT LOCATE A ‘D’ RING
UNDERNEATH THE FRONT FOOTREST
OF YOUR STROLLER, YOU MAY HAVE AN
OLDER MODEL TRI-MODE. FOR DETAILS
ON HOW TO ATTACH THE TODDLER SEAT
TO YOUR OLDER MODEL STROLLER,
PLEASE CONTACT VALCO DIRECT AT info@
valco.com.au (IN AUS) OR info@valcobaby.
com (IN NORTH AMERICA).
15. Locate the strap on the ‘U’ Shaped
metal bar that rests on the front of the
footrest.
FIGURE I
16. Thread the strap through the
D-shaped ring, from the front.
G
I
Locate strap
Locate metal ring
H
3
FIGURE J
17. Once through the D-shaped ring, bring
the strap back and upward towards you.
18. Thread the strap through the
rectangular metal ring attached to the
actual strap.
Be sure that the strap is threaded BEHIND
the movable metal separator in the ring.
(3)
19. Pushing the metal separator back
against the strap to make space, thread
the end of the strap into the space you
have just made. (4)
20. Pull the strap end through the ring as
far as you can to tighten, securing the font
end of your toddler seat to your stroller
frame.
FIGURE K
21. Now the Toddler Seat is safely
attached to your stroller, and ready for use.
FIGURE L
22. Be sure to remove and dispose of the
plastic from the front bumper bar of the
toddler seat.
23. Please dispose of all packaging
materials thoughtfully and responsibly.
J
K
L
1
2
3
4
Remove Plastic
4
TO FOLD YOUR TODDLER SEAT
DOWN WITH YOUR STROLLER:
FIGURE M
24. Locate the ap that covers the locking
pin in the nylon housing joining each leg
of the toddler seat.
25. Press down on the ap and pull the
“U” shape leg slightly from the housing.
26. Repeat this process on the other side.
27. Remove the “U” legs totally from the
housing.
FIGURE N
28. Fold the “U” frame forward so that it is
as parallel as possible to, and sitting on,
the front of the stroller.
29. Swivel the mini rid upward against the
underside of the toddler seat front bar.
30. Fold the toddler seat down onto the
“U” frame.
TO FOLD YOUR STROLLER
WITH THE TODDLER SEAT:
FIGURE 0
31. You should now be able to fold your
stroller as normal.
NOTE: WITH THE TODDLER SEAT FOLDED
IN PLACE, YOUR STROLLER WILL SIT UP
A LITTLE HIGHER THAN NORMAL IN THE
FOLDED POSITION.
M
N
O
5
ALSO AVAILABLE TO USE WITH
TWIN TODDLER SEAT:
TODDLER SEAT HOOD
The toddler seat hood offers your toddler
maximum coverage from the various
weather conditions you will inevitably
encounter. It is easily retractable and
attachable.
TODDLER SEAT RAINCOVER
The encompassing rain cover allows you
to protect all your children from the nasty
weather. With easily attachable Velcro and
extra ventilation, this rain cover is all you
need to protect the child in the stroller and
toddler seat too.
HITCHHIKER
This unique “platform step” fits easily on
the back of the Twin Tri-mode stroller for an
instant “ride” for an older child.
CUP HOLDER
This is just what you’ve been waiting for!
Keep beverages from spilling while on the
go with our sturdy cup holder. Fits your
coffee cup or water bottle (even the 1L)
equally well, and will attach to most stroller
handles.
AVAILABLE AT ALL GOOD RETAILERS!
The Toddler Seat Hood
The Cup Holder
The Hitchhiker
6
WARNINGS
Your child’s safety is your responsibility …
Be sure to check that all clamps and buckles are securely xed and in •
place before use.
Check all parts for breakage or fatigue before use. Discontinue •
immediately if any part is found to be damaged or broken.
The maximum weight of the toddler in this seat is 20 kg’s/ 45lbs. •
ALWAYS be sure your stroller wheels are fully inated before riding with •
the toddler seat. Fully inated tires provide the most stable platform and
are less susceptible to punctures and blowouts.
NEVER leave your child unattended while in any stroller or in this seat. •
NEVER remove your hands from the stroller handle while your child is in •
this seat.
To avoid tipping ALWAYS hold the stroller when your child is climbing into •
the seat.
NEVER leave the stroller at rest (parked) with a toddler in the seat. •
NEVER use this seat if the child is unwilling to sit in it. •
ALWAYS be aware of your child’s position when sitting in the toddler •
seat. Excessive leaning to one side or while the stroller is cornering, may
cause the unit to become unstable.
NEVER use this seat with a child under 6 months of age and/or is unable •
to sit up unassisted.
NEVER use this toddler seat with any other brand product. •
Only use this toddler seat with the correct model VALCO Tri-mode Twin •
Stroller.
ALWAYS ensure that each child is clear of all moving parts when •
adjusting the stroller.
NEVER leave any child unattended in the stroller. •
NEVER use on escalators or stairs. •
When in the stroller each child must ALWAYS wear the safety harness, •
correctly tted and adjusted, at all times.
This product is intended for domestic use only. It is not intended for •
commercial use.
In Australia/New Zealand
www.valco.com.au
www.valco.co.nz
In USA only
www.valcobaby.com
1 800 610 7850
In Canada
416 488 1900
Loading...