Twin Latitude Car
Seat Adapter
Compatible with most Peg Perego Car Seats
PRODUCT REFERENCE GUIDE
Thank you for purchasing a quality VALCO product. Please read and follow the instructions outlined in this
guide carefully. Familiarise yourself with the construction and safety features; be sure that you understand all
the warnings and safety guidelines before use. This product is for use with the VALCO Latitude stroller in North
American only. This product is not intended for use in Australia.
Important: Please read the following instructions carefully before assembling this product. Retain this
guide in a safe place for future reference.
Due to our policy of continuous
product development, this
product is constantly evolving. It
is possible that some features or
procedures outlined here have
changed since this document
was written. If you are unsure
of any procedure shown here,
please contact us via the web at
info@valcobaby.com to obtain
the most up to date information
before use. Include the batch
number, which can be found on a
sticker on the frame.
FURTHER INFORMATION
North America only
www.valcobaby.com
1800 610 7850
All pictures and diagrams herein
are provided for illustration
purposes only. Actual product,
color or fabric may vary. VALCO
reserves the right to modify or
alter any specication or color
without notice or obligation to
modify any product previously
purchased
© Copyright VE 2008
A
Hood
Seat Reclined
Adaptor Bar
1
2
Front View
INSTALLING YOUR PEG PEREGO
CAR SEAT ADAPTOR
FIGURE A
1. Begin preparing the Latitude stroller for the Car
Seat Adaptor by removing the canopy (hoods) from the
stroller and reclining the seats to their fully reclined
position (detailed instructions in the Twin Latitude
Stroller Instruction Manual).
2. Remove the bumper bar, (detailed instructions in the
Twin Latitude Stroller Instruction Manual).
B
C
3. Remove the extra hood and Peg Perego Adaptor
Bar from the packaging and dispose of packaging
responsibly.
FIGURE B
4. Prepare the Hood for installation by rotating the
hood rods so they are aligned with the corresponding
connector pieces on the stroller frame (where the twin
hood was connected.) (1)
NOTE: ENSURE THAT THE HOOD IS PLACED OVER THE
LEFT SEAT OF THE STROLLER (WHEN FACING YOU).
5. Simultaneously slide the hood rods onto the
corresponding raised pieces on the stroller frame and
lock into place. (2)
Figure C
6. Align the Adaptor Bar connector piece with the
corresponding raised piece on the outer frame of the
stroller.
NOTE: BE SURE THAT THE ADAPTOR BAR IS IN ITS
UPRIGHT POSITION BY PULLING THE SUPPORT BAR
AWAY FROM THE ADAPTOR FRAME.
D
7. Slide the Adaptor onto the corresponding raised piece
and lock into place.
NOTE: ONLY ONE SIDE OF THE ADAPTOR WILL SLIDE
ONTO THE STROLLER FRAME. THE ADAPTOR WILL NOT
BE CONNECTED TO THE MIDDLE FRAME.
Figure D
8. Locate the middle hood connector piece.
9. Unscrew the screw, washer and nut from the middle
piece.
NOTE: THE UNSCREWING AND SCREWING IS ONLY
Front View
Press
3
4
E
PART OF THE INITIAL INSTALLATION PROCESS, AND
WILL NOT HAVE TO BE REPEATED WITH EACH USE.
FIGURE E
10. Insert the remaining unattached adaptor bar into
the centre of the middle connector piece.
F
G
H
FIGURE F
11. Align the adaptor piece with the middle connector
piece and hood piece.
12. Insert the screw, and secure with the washer and
nut.
13. The Adaptor is now secured to the frame with the
support bar resting on the edge of the seat, above the
footrest.
FIGURE G
14. Adjust the footrest upwards.
To do so: Press the adjust button, and move the footrest
to the desired position. (3)
15. Located on the car seat adaptor are two sets of
tether straps. The rst set (as shown in Figure G) rest on
the foot rest of the stroller. Adjust these straps so they
wrap underneath the foot rest of the stroller. (4)
16. Secure by inserting the male clip into the female
end. Ensure these straps are as tight as possible.
17. The adaptor is now securely attached to your stroller.
You may readjust the footrest to suit your child.
FIGURE H
18. Position the Car Seat so the infant is facing the
handlebar of the stroller.
19. Line the Car Seat up with the adaptor bar so that
the Car Seat rests on the adaptor bar when inserted.
IMPORTANT WARNING: ALWAYS TEST THAT ALL
STRAPS ARE SECURELY ENGAGED BEFORE
USE.
FIGURE I
I
20. Once your car seat is inserted, locate the remaining
set of straps.
21. Take the Male/Female strap and slip the strap
through the car seat belt hook on the side of the car
seat.
22. Repeat with the other strap.
23. Insert Male clip into its Female counterpart and
buckle.
24. Adjust straps to tighten around car seat.
25. You may want to readjust the recline of the seat
to ensure the car seat has the most comfortable and
secure ride.
TO REMOVE YOUR CAR SEAT:
26. Reverse the steps outlined in Figure I and lift out the
car seat.
TO REMOVE YOUR ADAPTOR:
27. Slide all three connector pieces from the stroller,
undo the buckle under the footrest and remove adaptor.
NOTE: THERE IS NO NEED TO UNSCREW THE ADAPTOR.
RETAIN THE ADAPTOR IN THIS FORM FOR EASY FUTURE
INSTALLATIONS.
WARNINGS
•Always follow car seat manufacturer’s instructions when using the car seat.
•Be sure to check that all straps are securely xed and in place before use.
• Check all parts for breakage or fatigue before use. Discontinue immediately if any part
is found to be damaged or broken.
• NEVER leave any child unattended at any time.
• This product is intended for use in North America only. It is not intended for use in
Australia.
• This product is intended for domestic use only. It is not intended for commercial use.
In North America only
www.valcobaby.com
1 800 610 7850
Loading...