p
Read and follow the instructions contained within carefully before use. Retain this guide in a
safe and easily accessible place for future reference.
Drawings, pictures and specifications contained in this manual are for illustration purposes only – actual product may vary. VALCO BABY
reserves the right to alter any specification(s), colour or features without prior notice or incurring any obligation to similarly alter products
reviously purchased.
Product Reference Guide
S E R I E S
Thank you for purchasing a quality VALCO product. Due to our policy of continuous product
development, this product is constantly evolving. It is possible that some features or procedures
outlined here have changed since this document was written. If you are unsure of any procedure
outlined here please contact the store from which you purchased it to obtain the most up to date
information, or contact us via the internet. See relevant web contact addresses on the back page.
Stroller Assembly/Opening
Remove the stroller from the carton and dispose of all packaging immediately including the black rubber protectors on either
side of the brake bar and front wheel protector. The front wheel forks, rear wheels, front bar and hood all need to be installed
prior to use.
1. Lay the stroller flat on the floor
and carefully cut the cable tie
which holds the frame.
2. Lift the handle upward to a
vertical position.
1. Lift the front wheel housing
upward so that the stroller
frame unfolds from beneath.
2. Press down on the locking hinge
with your hand or foot.
IMPORTANT WARNING: Always test that all latches are securely engaged before use.
1. Secure the frame closed by
swinging the fold latches
(located on both sides of the
frame) and fully engaging them
tightly onto the frame.
Installing/Removing the rear wheels
1. Pressing on the centre hub
button, insert the SQR axle
through the outside of the metal
hub in each wheel.
IMPORTANT: Insert through outside
of the wheel - the side which does
NOT have the nylon brake cog)
Your front bar
1. Pressing the axle button, insert
the protruding long axle into the
opening in the tube at the rear
of the stroller chassis.
2. Repeat this procedure for the
other side.
If your brakes do not engage, check to see that the nylon brake cogs are on the INSIDE of each wheel
when it is attached to the chassis. If not, remove the wheel and SQR axle and re-insert the SQR axle
from the other side of the wheel, so that the cog will be on the inside of the wheel.
1. To remove the wheel simply
press the axle button in the
centre of the wheel hub and
simultaneously pull the wheel
outward.
1. Remove the plugs from the nylon housing at either side of the stroller frame
by pressing each inner “release button” and pulling the plug upward.
2. Insert the bar ends into the nylon housing located on either side of the
frame. Be sure that the bar is securely engaged
3. Adjust the front bar by simultaneously pressing the 2 red buttons and
swivelling the bar (forward or backward) to the desired position.
4. To remove the front bar: Feeling the side of the nylon housing that sits below
the frame at each side (facing inward), locate the release “button.”
5. Press the release button inward while simultaneously pushing upward on the
bar housing. Repeat for the other side.
IMPORTANT WARNING: The front bar IS NOT a restraining device.
Installing/Removing and using the front wheel forks
Y
y
T
Y
our Runabout stroller utilizes our
unique and revolutionary new TRIMODE™ front swivel system:
1. To install the front fork, rotate the
TRI-MODE selection dial to the
centre (45
2. Tilt the stroller frame upward on
the rear wheels.
3. Insert the fork shaft into the TRI-
MODE housing till it “clicks” into
place.
IMPORTANT: Always test that the fork
is securely engaged in the housing.
0
) position.
Folding/Opening
1. Fold the hood back up against the
handle.
2. Release the locking clamps at
either side of the stroller.
4. Holding the frame at the rear,
press down with your foot on
the rear basket tube. This will
disengage the side hinge locks.
5. Continue pushing the rear of
the basket, moving the rear
wheels forward beneath the
frame.
our stroller
To remove the front fork:
1. Rotate the TRI-MODE
selection dial to the centre
0
) position.
(45
2. Tilt the stroller frame upward
on the rear wheels.
3. Press the centre release
button. The fork will then be
released.
3. Simultaneously lift the
secondary safety catch and
swing the handle forward.
ou can lock the frame closed by
6.
stretching the locking strap over
the frame, placing the metal
catch over the rivet on the
chassis
The unique TRI-MODE™ swivel system is as
flexible as it is functional over a variety of
terrains and uses.
1. LOCK
2. O
3. SWIVEL:
: This position is best for use on
extremely rough or soft terrain such
as sand etc which inhibit wheel swivel.
To lock your wheel, rotate the dial to
the “LOCK” position. Swivel the wheel
around till it locks into position.
:
The central position locks the wheel
into a tight 45
provides more stability for use with a
toddlerseat or when going down
inclines.
unfettered swivel action.
0
swivel arc. This
This position allows full,
o open, unhook the frame
1.
locking strap reversing the
previous step.
2. Holding on to the side of the
footrest, with your foot
stopping the rear wheels, lift
the handle so that the frame
begins to unfold.
Adjusting your seat – zip/belt System (selected units)
Y
(selected units)
T
NOTE: Before using your stroller, be sure to attach the tether straps around the stroller frame by feeding the strap through
the slit in the steel buckle. While not essential for safety, these help reduce the motion of the seat within the stroller frame.
3. Press down on the side locking
hinges (on the basket) to lock
the frame in the open position.
4. Secure the handle to the
frame by engaging the locking
clamps on both sides.
NOTE: Special care must be taken
when adjusting the seat position with
a child in the stroller. Before adjusting
the zippers, place your hand beneath
the seat at its current position and lift
it slightly. This will relieve pressure on
the zippers and make them easier to
adjust.
1. To recline, pull one of the zippers
2. Do the same to the corresponding
3. For more recline, release more
4. For seat incline simply reverse this
BE SURE THAT ALL ZIPPERS ARE
OPENED/CLOSED FULLY BEFORE USE.
“no zip” recline
he new “no zip” recline offers an
almost infinite amount of seat
adjustments:
1. RECLINE: While squeezing the
centre release mechanism in a
pincer action, ease the seat down
to the desired position.
2. INCLINE: Place your hand in the
centre of the rear of the seat.
3. Pull the incline strap while gently
pushing on the rear of the seat
until the desired position has been
reached.
ALWAYS TEST that the seat is
securely locked in place.
IMPORTANT: Always check that
the brake has fully engaged
our seat can be adjusted to 4 positions
using the zip system
located on the seat side downward.
zipper on the other side of the seat
zippered sections.
procedure.
In addition to the 4 adjustment
positions using the zip system, your
stroller has an additional 5
which raises the seat to an even more
upright sitting position.
1. With all zippers fully closed, lift
the seat back further upward
with your hand.
2. Secure the seat with the two
sets of straps (one at the top
and one at the bottom of the
seat back), inserting each
buckle into the corresponding
buckle housing in the matching
strap.
Installing your hood Using your brakes
1. Place the plastic hood housings
over the corresponding housing on
either side of the stroller frame.
2. Align the straight track on the
stroller housing with the
corresponding “hole” in the hood
housing.
3. Slide the hood housing downward,
over the track, so that it
completely engages onto the
stroller frame.
There are two available brake
systems available for the Runabout
Tri Mode series:
STANDARD BRAKE (pictured)
1. Press down on the centre of the
brake bar until the bar ends
engage in the nylon brake cogs
on the wheel.
2. To disengage, lift the brake bar
upward till it locks in the upright
position.
CONCEALED BRAKE:
1. Press the centre toggle down
firmly with your foot until you
feel the wheels have locked.
2. To release, lift the centre toggle
from beneath with your foot.
th
position
IMPORTANT WARNING: Always test that all axles, wheels, front bar, hinges and locks are securely engaged before use.
EXTRAS
Y
Y
Y
Y
g y
C
B
Y
1
2
Optional Extra on most models
our Runabout is equipped with a tire
pump that hangs in a special pocket
found sewn beneath the seat at the
rear.
Your tires should be kept at a
pressure of 40 p.s.i. Under inflated
tyres can cause excessive and uneven
tire wear, greater susceptibility to
punctures and greater difficulty in
smooth operation.
our Runabout is equipped with a
removable “Head Hugger” and
shoulder harness covers. The
“Head Hugger” is designed to
optimize the comfort of newborn
babies within the stroller. The
shoulder straps increase your
child’s comfort levels when in the
harness as well as keeping
harness adjusters away from busy
fingers.
our Runabout hood is fitted with a
zip system to which attaches our
unique silver insect mesh (optional
extra on most models)
This protective mesh has been
tested and proven to block out up to
80%* of UV rays
tested to Australian Standard 4399)
(*
AIRGO™ SYSTEM
our Runabout has been designed to maximise air flow
within the stroller by way of our exclusive Airgo™ system.
This unique system combines a special breathable seat
fabric, with our new flexible hood. The hood incorporates a
built in storage bag, designed to zip off when more air flow
is required, to reveal an additional mesh air vent. The bag is
designed “to go” or can be easily hung from the stroller
handle.
Usin
our Runabout stroller is fitted with our unique new multi point safety harness system. Your
TO SECURE YOUR CHILD IN THE HARNESS:
1. Overlap buckles (A) and (B) so that they fit together to form one complete buckle.
2. Insert the completed buckle into the Buckle Housing (C) until it engages securely in place.
3. Carefully adjust the harness straps to snugly fit your child by adjusting the Sliders
located on all Shoulder Straps, Waist Straps and the Crotch Strap.
4. Your harness can be adjusted for even more comfort for smaller or larger children (at the
top of the seat back and front of the seat) by threading/removing the crotch or shoulder
straps through the webbing sewn into the seat. You will need to detach the waist straps
at the sides of the stroller in order to do so. (To detach the waist straps: With a pincer
movement, depress the centre buckle button and pull the strap free from the housing.)
5. To prevent older children tampering with the strap adjustments and for greater child
comfort, your RUNABOUT stroller is provided with 2 soft strap covers for each harness.
To fit, detach the waist straps at the sides of the stroller (as in point 4) and thread the
strap through the strap cover. Re-attach each strap.
The harness should be snugly fitted to the baby’s body, tight enough so that the baby cannot
wriggle itself free of the straps but loose enough so as not to cause the baby any discomfort.
TO OPEN YOUR HARNESS
1. Press down on the Buckle Prongs (1).
2. Simultaneously push the release button in the centre of the buckle (2)
3. Pull the buckles from the Buckle Housing.
Your harness system has been designed to meet very stringent safety standards and incorporates
our unique secondary action. This helps ensure that your child cannot release the harness unaided.
our harness
MUST always be harnessed while in the stroller.
child
:
A
OPTIONAL/ADDITIONAL ACCESSORIES
r
T
Available in versions for both Single and Twin Runabout
models, the optional toddlerseat sits firmly inside the chassis.
Perfect for twins and an older sibling (Twin model) or when a
new baby comes along and junior still likes to go for a ride!
Both Twin and single models even fold totally out of the way
with the stroller! See your local specialist retailer for more
info and suitability.
Sunstopper (Universal fit)
The unique SUNSTOPPER
provides the ultimate
protection from the suns
harsh rays, while providing a
comfortable open environment
for the child. The roll up blind
system means that the child
can be shielded from the sun
without being fully enclosed,
and folds up into its own self
enclosed pouch for easy
storage.
Toddlerseat
Bottle/Cup Holde
(Universal fit)
The revolutionary VALCO
BABY cup/bottle holder was
designed for the busy
lifestyle of today’s parents
and carers. With the
specially designed holding
section big enough to
accommodate up to a 1.5
litre bottle or those big
coffee cups, refreshment is
always within easy reach!
UV Protective Insect Net
Our unique insect net zips directly in to the inside of your
RUNABOUT Tri Mode hood. In addition to keeping baby
cool, comfortable and safe from insects, it also blocks up
to a massive 80%* of the sun’s harmful UV rays.
(* tested to Australian Standard 4399)
Boot cover
The generous proportions
of this fleecy lined boot
keep your child warm and
protected from the
elements while offering a
sense of space without
constriction.
ravel Storage Bag
Available in BLACK only,
the travel bag is
specifically tailored to the
RUNABOUT model and
provides sections and
compartments for all the
components including
wheels, axles etc.
With tailored slots for the
harness system, the fleecy
lined muff keeps your child
comfortable in cool
conditions, while the top
zips off to convert it to a
comfy stroller pad.
With all the features of the
standard model, the 4
season model includes a zip
out top section which
reveals our unique 80%* UV
protective net. This allows
even more cool and
regulated airflow in warmer
conditions.
Foot Muff
4 Season Foot Muff
The VALCO HITCHHIKER is a boon to any parent with a child who is old enough to walk but
young enough to need to rest along the way. Made of high quality and extremely sturdy
materials (maximum weight 30 kg’s / 66 lb’s), the HITCHHIKER is easily adjustable for height,
width and distance from the stroller which makes it fit most brands, makes and models of
strollers. The handy “hang up” system means it can hang out of the way when not in use,
while the unique quick release systems allows for quick and easy removal.
All this and more makes the HITCHHIKER the perfect option for that “in between” age child.
See your local specialist retailer for more information.
WARNINGS
g,
Be sure to check that all clamps and buckles are securely fixed and in place before use.
Check all parts for breakage or fatigue before use. Discontinue immediately if any part is found to
be damaged or broken.
The maximum weight of the child for which this stroller is intended is 22 kg’s (48 lbs)
The maximum height of the child for which this stroller is intended is 106 cm (42 in)
This product will become unstable if the recommended load is exceeded.
Can be used from birth +. A cocoon specially designed to be used with a stroller is recommended
when any fully reclining stroller is used with a newborn.
NEVER jog with a newborn baby in any pram or stroller until the child can sit up
unassisted (approximately 6 months).
ALWAYS ensure that the child is clear of all moving parts when adjusting the stroller.
ALWAYS beware of little fingers when folding or unfolding your stroller to prevent finger
entrapments.
ALWAYS engage the brake system when the stroller is at rest.
NEVER leave any child unattended in the stroller.
NEVER use on escalators or stairs.
When in the stroller the child must ALWAYS wear the safety harness, correctly fitted and adjusted,
at all times.
DO NOT hang shopping bags from the handle as this may affect the stroller’s stability.
Always use the basket provided, the maximum weight in the basket is 6 kg’s (13 lbs)
Do not carry additional children. It may be unsafe to use any accessories other than VALCO
approved ones.
ALWAYS be aware of the risks provided by fire and other significant sources of heat such as
radiators etc. which may be in the immediate vicinity of your stroller.
This product is intended for domestic use only. It is not intended for commercial use.
Continued and extended exposure to sunlight and the elements can change the colours of many
materials. To avoid fadin
Caring for your stroller
Moving parts may be lubricated with silicone based lubricants – do not use oil.
Regularly check wheels for loose spokes – tighten as necessary.
Your Runabout chassis is made of aluminium alloy but does include some metal parts. Special
care must always be taken to avoid rust. If this pram is used near the ocean or salty air
environments, spray the chassis and seat frame with water and dry thoroughly. This is
particularly important for parts such as wheel spokes and springs. We recommend rust
inhibiting product should be applied to prevent accelerated rust and fatigue of these metal parts!
We recommend that you wipe down axles and lubricate the wheels every 3 months,
particularly the front wheel and housing. Sand and dirt can grind down axles so, if you
live, walk or run near/on the beach or in a dusty environment, you must remove and
wipe down the axles and wheels, then lubricate them MONTHLY.
AXLES AND MOVING PARTS ARE BEST LUBRICATED WITH SILICONE BASED
PRODUCTS. DO NOT USE OIL BASED PRODUCTS.
Your child’s safety is your responsibility ………
always cover and store in a shaded area.
In Australia/NZ In North America
www.valco.com.au
www.valcobaby.com
© Copyright VE 2006
www.valco.co.nz
1 800 610-7850
Loading...