Valco baby TRIMODE, TWIN EX Product Reference Manual
Thank you for purchasing a quality Valco Baby product. Please read and follow the instructions outlined in this
guide carefully. Familiarise yourself with the construction and safety features; be sure that you understand all
the warnings and safety guidelines before use.
Important: Please read the following instructions carefully before assembling this product. Retain this
guide in a safe place for future reference.
PRODUCT REFERENCE GUIDE
© Copyright VE 2009
Due to our policy of continuous product
development, this product is constantly
evolving. It is possible that some
features or procedures outlined here
have changed since this document
was written. If you are unsure of any
procedure shown here, please contact
us via the web at info@valcobaby.com
to obtain the most up to date information
before use. Include the batch number,
which can be found on a sticker on the
frame.
All pictures and diagrams herein are
provided for illustration purposes only.
Actual product, color or fabric may vary.
Valco Baby reserves the right to modify
or alter any specication or colour
without notice or obligation to modify any
product previously purchased
FURTHER INFORMATION
In Australia/New Zealand
www.valco.com.au
www.valco.co.nz
In North America only
www.valcobaby.com
1800 610 7850
TRIMODE
TWIN EX
STOLLER
Opening the strOller chassis
FIGURE A
1. Lay the stroller at on the oor and carefully cut the
cable tie which holds the frame. To unfold the chassis,
locate the rear legs.
NOTE: The rear centre leg is highlighted in red.
2. Holding the rear centre leg, lift the stroller upwards. Pull
the centre leg outwards as far as it can go.
FIGURE B
3. Lift the handlebar upward towards you until the stroller is
in a vertical position.
4. Secure the stroller by swinging the locking clamps
(located on both sides of the frame) and fully engaging
them tightly onto the frame.
FIGURE C
5. Press down on the basket frame locking hinge with your
hand or foot.
IMPORTANT WARNING: ALWAYS TEST THAT ALL LATCHES
ARE SECURELY ENGAGED BEFORE USE.
installing the wheels
FIGURE D
6. Pressing on the centre axle button, insert the Super Quick
Release (SQR) axle through the outside of the hub in each
wheel.
IMPORTANT: INSERT THROUGH OUTSIDE OF THE WHEEL
(THE SIDE WHICH DOES NOT HAVE THE NYLON BRAKE COG).
A
C
B
D
Outside
wheel hub
Axle button
Nylon
brake
cog
FIGURE E
7. Press the axle button and insert the protruding long axle
into the opening on the stroller frame beneath the brake.
Release the axle button when wheel is in place to secure.
NOTE: Ensure that the brake pedal is fully retracted, so that the
brake pin (highlighted in red) does not obstruct the wheel cog
from fully engaging the housing.
8. Repeat the procedure for the other side. TEST that each
wheel is securely engaged by pulling on it.
9. To remove the wheel, simply press the axle button in
the centre of the wheel hub and simultaneously pull the
wheel outward.
IMPORTANT NOTE: If your brakes do not engage, check to see the
nylon brake cogs are on the INSIDE of each wheel when it is
attached to the chassis. If not, remove the wheel and SQR axle
and re-insert the SQR axle from the other side of the wheel, so
that the cog will be on the inside of the wheel.
FIGURE F
Your Twin Tri-mode stroller utilizes our unique and revolutionary
new DUAL TRIMODE ™ front swivel system:
10. Tilt the stroller frame upward so that it rests on the
handle and the rear wheels.
11. Insert each fork shaft respectively into each
TRI-MODE housing till it “clicks” into place.
IMPORTANT: Before use, always test that the fork is securely
engaged in the housing by pulling on it.
To remove the front fork:
12. Rotate the TRI-MODE selection dial to the centre (45°)
position.
13. Tilt the stroller frame upward so that it rests on the
handle and the rear wheels.
14. Press the centre release button and pull the fork away
from the mechanism.
FIGURE G
The unique TRI-MODE™ swivel system is as exible as it is
functional over a variety of terrains and uses.
15. LOCK: This position is best for use on extremely rough or
soft terrain such as sand etc which inhibit wheel swivel.
To lock your wheel, rotate the dial to the “LOCK” position.
Swivel the wheel around till it locks into position.
16. O: The central position locks the wheel into a tight 45°
swivel arc. This provides more stability for use with a
toddlerseat or when going down inclines so as not to turn
so sharply!
17. SWIVEL: This position allows full, unfettered Installing/
Removing your hoods 360° swivel action.
E
F
G
9
b
a
b
y
l
o
c
k
s
w
i
v
e
l
14
Loading...