Valco baby RunAbout Tri-mode series Product Reference Manual

Product Reference Guide
Read and follow the instructions contained within carefully before use. Retain this guide in a safe and easily accessible place for future reference.
S E R I E S
Drawings, pictures and specifications contained in this manual are for illustration purposes only – actual product may vary. VALCO BABY reserves the right to alter any specification(s), colour or features without prior notice or incurring any obligation to similarly alter products
reviously purchased.
Thank you for purchasing a quality VALCO product. Due to our policy of continuous product development, this product is constantly evolving. It is possible that some features or procedures outlined here have changed since this document was written. If you are unsure of any procedure outlined here please contact the store from which you purchased it to obtain the most up to date information, or contact us via the internet. See relevant web contact addresses on the back page.
Stroller Assembly/Opening
Remove the stroller from the carton and dispose of all packaging immediately including the black rubber protectors on either side of the brake bar and front wheel protector. The front wheel forks, rear wheels, front bar and hood all need to be installed prior to use.
1. Secure the frame closed by
swinging the fold latches (located on both sides of the frame) and fully engaging them tightly onto the frame.
1. Lift the front wheel housing
upward so that the stroller frame unfolds from beneath.
2. Press down on the locking hinge
with your hand or foot.
1. Lay the stroller flat on the floor
and carefully cut the cable tie which holds the frame.
2. Lift the handle upward to a
vertical position.
IMPORTANT WARNING: Always test that all latches are securely engaged before use.
Installing/Removing the rear wheels
1. Pressing on the centre hub
button, insert the SQR axle through the outside of the metal
hub in each wheel. IMPORTANT: Insert through outside of the wheel - the side which does NOT have the nylon brake cog)
1. To remove the wheel simply
press the axle button in the centre of the wheel hub and simultaneously pull the wheel outward.
1. Pressing the axle button, insert
the protruding long axle into the opening in the tube at the rear of the stroller chassis.
2. Repeat this procedure for the
other side.
If your brakes do not engage, check to see that the nylon brake cogs are on the INSIDE of each wheel when it is attached to the chassis. If not, remove the wheel and SQR axle and re-insert the SQR axle from the other side of the wheel, so that the cog will be on the inside of the wheel.
Your front bar
1. Remove the plugs from the nylon housing at either side of the stroller frame
by pressing each inner “release button” and pulling the plug upward.
2. Insert the bar ends into the nylon housing located on either side of the
frame. Be sure that the bar is securely engaged
3. Adjust the front bar by simultaneously pressing the 2 red buttons and
swivelling the bar (forward or backward) to the desired position.
4. To remove the front bar: Feeling the side of the nylon housing that sits below
the frame at each side (facing inward), locate the release “button.”
5. Press the release button inward while simultaneously pushing upward on the
bar housing. Repeat for the other side.
IMPORTANT WARNING: The front bar IS NOT a restraining device.
Installing/Removing and using the front wheel forks
Y
our Runabout stroller utilizes our unique and revolutionary new TRI­MODE™ front swivel system:
1. To install the front fork, rotate the
TRI-MODE selection dial to the centre (45
0
) position.
2. Tilt the stroller frame upward on
the rear wheels.
3. Insert the fork shaft into the TRI-
MODE housing till it “clicks” into place.
IMPORTANT: Always test that the fork is securely engaged in the housing.
To remove the front fork:
1. Rotate the TRI-MODE
selection dial to the centre (45
0
) position.
2. Tilt the stroller frame upward
on the rear wheels.
3. Press the centre release
button. The fork will then be released.
The unique TRI-MODE™ swivel system is as flexible as it is functional over a variety of terrains and uses.
1. LOCK
: This position is best for use on extremely rough or soft terrain such as sand etc which inhibit wheel swivel. To lock your wheel, rotate the dial to the “LOCK” position. Swivel the wheel around till it locks into position.
2. O
:
The central position locks the wheel
into a tight 45
0
swivel arc. This provides more stability for use with a toddlerseat or when going down inclines.
3. SWIVEL:
This position allows full,
unfettered swivel action.
Folding/Opening
y
our stroller
1. Fold the hood back up against the
handle.
2. Release the locking clamps at
either side of the stroller.
3. Simultaneously lift the
secondary safety catch and swing the handle forward.
4. Holding the frame at the rear,
press down with your foot on the rear basket tube. This will disengage the side hinge locks.
5. Continue pushing the rear of
the basket, moving the rear wheels forward beneath the frame.
1.
T
o open, unhook the frame locking strap reversing the previous step.
2. Holding on to the side of the
footrest, with your foot stopping the rear wheels, lift the handle so that the frame begins to unfold.
6.
Y
ou can lock the frame closed by stretching the locking strap over the frame, placing the metal catch over the rivet on the chassis
NOTE: Before using your stroller, be sure to attach the tether straps around the stroller frame by feeding the strap through
the slit in the steel buckle. While not essential for safety, these help reduce the motion of the seat within the stroller frame.
Adjusting your seat – zip/belt System (selected units)
In addition to the 4 adjustment positions using the zip system, your stroller has an additional 5
th
position which raises the seat to an even more upright sitting position.
1. With all zippers fully closed, lift
the seat back further upward with your hand.
2. Secure the seat with the two
sets of straps (one at the top and one at the bottom of the seat back), inserting each buckle into the corresponding buckle housing in the matching strap.
Y
our seat can be adjusted to 4 positions
using the zip system
1. To recline, pull one of the zippers
located on the seat side downward.
2. Do the same to the corresponding
zipper on the other side of the seat
3. For more recline, release more
zippered sections.
4. For seat incline simply reverse this
procedure.
BE SURE THAT ALL ZIPPERS ARE OPENED/CLOSED FULLY BEFORE USE.
3. Press down on the side locking
hinges (on the basket) to lock the frame in the open position.
4. Secure the handle to the
frame by engaging the locking clamps on both sides.
NOTE: Special care must be taken when adjusting the seat position with a child in the stroller. Before adjusting the zippers, place your hand beneath the seat at its current position and lift it slightly. This will relieve pressure on the zippers and make them easier to adjust.
“no zip” recline
(selected units)
Installing your hood Using your brakes
There are two available brake systems available for the Runabout Tri Mode series:
STANDARD BRAKE (pictured)
1. Press down on the centre of the
brake bar until the bar ends engage in the nylon brake cogs on the wheel.
2. To disengage, lift the brake bar
upward till it locks in the upright position.
CONCEALED BRAKE:
1. Press the centre toggle down
firmly with your foot until you feel the wheels have locked.
2. To release, lift the centre toggle
from beneath with your foot.
1. Place the plastic hood housings
over the corresponding housing on either side of the stroller frame.
2. Align the straight track on the
stroller housing with the corresponding “hole” in the hood housing.
3. Slide the hood housing downward,
over the track, so that it completely engages onto the stroller frame.
T
he new “no zip” recline offers an almost infinite amount of seat adjustments:
1. RECLINE: While squeezing the
centre release mechanism in a pincer action, ease the seat down to the desired position.
2. INCLINE: Place your hand in the
centre of the rear of the seat.
3. Pull the incline strap while gently
pushing on the rear of the seat until the desired position has been reached.
ALWAYS TEST that the seat is securely locked in place.
IMPORTANT: Always check that
the brake has fully engaged
IMPORTANT WARNING: Always test that all axles, whee ls, front bar, hinges and locks are securely engaged before use.
EXTRAS
Optional Extra on most models
Y
our Runabout is equipped with a tire pump that hangs in a special pocket found sewn beneath the seat at the rear.
Your tires should be kept at a pressure of 40 p.s.i. Under inflated tyres can cause excessive and uneven tire wear, greater susceptibility to punctures and greater difficulty in smooth operation.
Y
our Runabout is equipped with a removable “Head Hugger” and shoulder harness covers. The “Head Hugger” is designed to optimize the comfort of newborn babies within the stroller. The shoulder straps increase your child’s comfort levels when in the harness as well as keeping harness adjusters away from busy fingers.
Y
our Runabout hood is fitted with a zip system to which attaches our unique silver insect mesh (optional extra on most models)
This protective mesh has been tested and proven to block out up to
80%* of UV rays
(*
tested to Australian Standard 4399)
AIRGO™ SYSTEM
Y
our Runabout has been designed to maximise air flow within the stroller by way of our exclusive Airgo™ system. This unique system combines a special breathable seat fabric, with our new flexible hood. The hood incorporates a built in storage bag, designed to zip off when more air flow is required, to reveal an additional mesh air vent. The bag is designed “to go” or can be easily hung from the stroller handle.
Usin
g y
our harness
C
B
A
Y
our Runabout stroller is fitted with our unique new multi point safety harness system. Your
child
MUST always be harnessed while in the stroller.
TO SECURE YOUR CHILD IN THE HARNESS:
1. Overlap buckles (A) and (B) so that they fit together to form one complete buckle.
2. Insert the completed buckle into the Buckle Housing (C) until it engages securely in place.
3. Carefully adjust the harness straps to snugly fit your child by adjusting the Sliders
located on all Shoulder Straps, Waist Straps and the Crotch Strap.
4. Your harness can be adjusted for even more comfort for smaller or larger children (at the
top of the seat back and front of the seat) by threading/removing the crotch or shoulder straps through the webbing sewn into the seat. You will need to detach the waist straps at the sides of the stroller in order to do so. (To detach the waist straps: With a pincer movement, depress the centre buckle button and pull the strap free from the housing.)
5. To prevent older children tampering with the strap adjustments and for greater child
comfort, your RUNABOUT stroller is provided with 2 soft strap covers for each harness. To fit, detach the waist straps at the sides of the stroller (as in point 4) and thread the strap through the strap cover. Re-attach each strap.
The harness should be snugly fitted to the baby’s body, tight enough so that the baby cannot wriggle itself free of the straps but loose enough so as not to cause the baby any discomfort.
1
2
TO OPEN YOUR HARNESS
:
1. Press down on the Buckle Prongs (1).
2. Simultaneously push the release button in the centre of the buckle (2)
3. Pull the buckles from the Buckle Housing.
Your harness system has been designed to meet very stringent safety standards and incorporates our unique secondary action. This helps ensure that your child cannot release the harness unaided.
OPTIONAL/ADDITIONAL ACCESSORIES
UV Protective Insect Net
Our unique insect net zips directly in to the inside of your RUNABOUT Tri Mode hood. In addition to keeping baby cool, comfortable and safe from insects, it also blocks up to a massive 80%* of the sun’s harmful UV rays.
(* tested to Australian Standard 4399)
Toddlerseat
Available in versions for both Single and Twin Runabout models, the optional toddlerseat sits firmly inside the chassis. Perfect for twins and an older sibling (Twin model) or when a new baby comes along and junior still likes to go for a ride! Both Twin and single models even fold totally out of the way with the stroller! See your local specialist retailer for more info and suitability.
Sunstopper (Universal fit)
The unique SUNSTOPPER provides the ultimate protection from the suns harsh rays, while providing a comfortable open environment for the child. The roll up blind system means that the child can be shielded from the sun without being fully enclosed, and folds up into its own self enclosed pouch for easy storage.
Bottle/Cup Holde
r
(Universal fit)
The revolutionary VALCO BABY cup/bottle holder was designed for the busy lifestyle of today’s parents and carers. With the specially designed holding section big enough to accommodate up to a 1.5 litre bottle or those big coffee cups, refreshment is always within easy reach!
T
ravel Storage Bag
Available in BLACK only, the travel bag is specifically tailored to the RUNABOUT model and provides sections and compartments for all the components including wheels, axles etc.
4 Season Foot Muff
With all the features of the standard model, the 4 season model includes a zip out top section which reveals our unique 80%* UV protective net. This allows even more cool and regulated airflow in warmer conditions.
Boot cover
The generous proportions of this fleecy lined boot keep your child warm and protected from the elements while offering a sense of space without constriction.
Foot Muff
With tailored slots for the harness system, the fleecy lined muff keeps your child comfortable in cool conditions, while the top zips off to convert it to a comfy stroller pad.
The VALCO HITCHHIKER is a boon to any parent with a child who is old enough to walk but young enough to need to rest along the way. Made of high quality and extremely sturdy materials (maximum weight 30 kg’s / 66 lb’s), the HITCHHIKER is easily adjustable for height, width and distance from the stroller which makes it fit most brands, makes and models of strollers. The handy “hang up” system means it can hang out of the way when not in use, while the unique quick release systems allows for quick and easy removal.
All this and more makes the HITCHHIKER the perfect option for that “in between” age child. See your local specialist retailer for more information.
Your child’s safety is your responsibility ………
WARNINGS
Be sure to check that all clamps and buckles are securely fixed and in place before use. Check all parts for breakage or fatigue before use. Discontinue immediately if any part is found to
be damaged or broken.
The maximum weight of the child for which this stroller is intended is 22 kg’s (48 lbs) The maximum height of the child for which this stroller is intended is 106 cm (42 in) This product will become unstable if the recommended load is exceeded. Can be used from birth +. A cocoon specially designed to be used with a stroller is recommended
when any fully reclining stroller is used with a newborn.
NEVER jog with a newborn baby in any pram or stroller until the child can sit up
unassisted (approximately 6 months).
ALWAYS ensure that the child is clear of all moving parts when adjusting the stroller. ALWAYS beware of little fingers when folding or unfolding your stroller to prevent finger
entrapments.
ALWAYS engage the brake system when the stroller is at rest. NEVER leave any child unattended in the stroller. NEVER use on escalators or stairs. When in the stroller the child must ALWAYS wear the safety harness, correctly fitted and adjusted,
at all times.
DO NOT hang shopping bags from the handle as this may affect the stroller’s stability. Always use the basket provided, the maximum weight in the basket is 6 kg’s (13 lbs) Do not carry additional children. It may be unsafe to use any accessories other than VALCO
approved ones.
ALWAYS be aware of the risks provided by fire and other significant sources of heat such as
radiators etc. which may be in the immediate vicinity of your stroller.
This product is intended for domestic use only. It is not intended for commercial use. Continued and extended exposure to sunlight and the elements can change the colours of many
materials. To avoid fadin
g,
always cover and store in a shaded area.
Caring for your stroller
Moving parts may be lubricated with silicone based lubricants – do not use oil. Regularly check wheels for loose spokes – tighten as necessary.
Your Runabout chassis is made of aluminium alloy but does include some metal parts. Special care must always be taken to avoid rust. If this pram is used near the ocean or salty air environments, spray the chassis and seat frame with water and dry thoroughly. This is particularly important for parts such as wheel spokes and springs. We recommend rust inhibiting product should be applied to prevent accelerated rust and fatigue of these metal parts!
We recommend that you wipe down axles and lubricate the wheels every 3 months, particularly the front wheel and housing. Sand and dirt can grind down axles so, if you live, walk or run near/on the beach or in a dusty environment, you must remove and wipe down the axles and wheels, then lubricate them MONTHLY.
AXLES AND MOVING PARTS ARE BEST LUBRICATED WITH SILICONE BASED PRODUCTS. DO NOT USE OIL BASED PRODUCTS.
www.valco.com.au www.valco.co.nz
In Australia/NZ In North America
www.valcobaby.com
1 800 610-7850
© Copyright VE 2006
Loading...