Thank you for purchasing a quality VALCO product. Please read and follow the instructions outlined in this
guide carefully. Familiarise yourself with the construction and safety features; be sure that you understand all
the warnings and safety guidelines before use.
Retain this guide in a safe place for future reference.
PRODUCT REFERENCE GUIDE
Due to our policy of continuous product development, this product is
constantly evolving. It is possible that some features or procedures outlined
here have changed since this document was written.
If you are unsure of any procedure shown here, please contact us via the web
at info@valco.com.au to obtain the most up to date information before use.
Include the batch number, which can be found on a sticker on the frame.
All pictures and diagrams herein are provided for illustration purposes only.
Actual product, colour or fabric may vary. VALCO reserves the right to modify
or alter any specication or colour without notice or obligation to modify any
product previously purchased
FURTHER INFORMATION
In Australia/New Zealand
www.valco.com.au
In North America only
www.valcobaby.com
1800 610 7850
REBEL Q STROLLER
WITH OPTIONAL
BASSINET ACCESSORY
© Copyright VE 2011
vs020811
ASSEMBLY
OPENING YOUR STROLLER
FIGURE A
1. Remove the stroller from the carton and dispose
of all packaging responsibly. The front wheels, rear
wheels, seat, bumper bar and hood all need to be
installed prior to use
2. Lay the stroller frame at on the ground with the
handle facing upwards. Release the frame lock if
engaged (see Diagram Q)
3. Lift the handle upward to a vertical position. You
will feel the chassis unfolding as you lift.
FIGURE B
4. Continue to lift the handle until you feel the
chassis lock into the open position.
IMPORTANT WARNING: ALWAYS TEST THAT ALL
LATCHES ARE SECURELY ENGAGED BEFORE USE.
INSTALLING/REMOVING THE WHEELS
FIGURE C - REAR WHEELS
5. Pressing on the axle release button, insert the
axle through the outside of the metal hub and
through the nylon brake cog.
IMPORTANT: INSERT THROUGH OUTSIDE OF THE
WHEEL - THE SIDE WHICH DOES NOT HAVE THE
BRAKE COG SPROCKETS
6. While pressing the axle release button (6), insert
the wheel axle into the wheel housing of the frame
at the rear of the stroller chassis.
7. Keeping the axle release button depressed, insert
the wheel as far as it will go into the channel.
Release the button and pull the wheel slightly
back toward you to ensuring that it has locked
securely into place.
8. Repeat this procedure for the other wheel.
9. To remove a rear wheel, rmly grasp the wheel
spokes while pressing the axle release button.
Gently pull the wheel free of the wheel housing.
FIGURE D - FRONT WHEELS
10. Line each front wheel pin (10) with the
corresponding front wheel housing (11).
11. Insert wheel pin into the wheel housing and push
it up until it clicks into place.
12. To remove the front wheel, rmly grasp the wheel
while pressing the wheel release button (13) and
gently pull the wheel free of the wheel housing
PRESS
6
A
B
C
Outside
wheel hub
Axle button
5
click
10
11
13
D
FIGURE E - FRONT WHEEL LOCK
13. The front wheels of your stroller offer either a full,
360º swivel action or a locked position.
14. To lock the front wheel, turn the wheel so that the
bulk of it is beneath the stroller and push down on
the wheel lock (14) until it locks into position.
15. Repeat this procedure for the other side.
IMPORTANT WARNING: ALWAYS TEST THAT THE LOCKS
ARE FULLY ENGAGED BEFORE USE.
INSTALLING THE SEAT
FIGURE F
16. Line up the seat housing with the corresponding
connectors located on either side of the stroller frame.
17. Lower the seat onto the connectors and gently push the
seat down until it clicks securely into place.
NOTE: YOUR SEAT CAN BE INSTALLED EITHER
FORWARD OR REARWARD FACING.
18. To remove the seat, simultaneously depress both
buttons in the seat housing on either side of the seat
unit and lift the seat unit from the frame.
IMPORTANT WARNING: NEVER REMOVE/RELEASE THE
SEAT WITH A CHILD IN IT.
INSTALLING THE BUMPER BAR
FIGURE G - BUMPER BAR
19. Insert the front bar ends into the nylon housings
located on either side of the frame. Be sure that the
bar is securely engaged.
20. Wrap the crotch strap around the installed bumper
bar and snap into position
21. Adjust the front bar by simultaneously pressing the
button on the bar housing and swivelling the bar to
the uppermost position. This is the only position for
use with a child in the stroller.
22. To remove the front bar: Feeling the side of the
nylon housing that sits below the frame at each side
(facing inward), locate the release button.
23. Press each release button inward while simultaneously
pulling upward on the bar housing. Repeat for the other
side. Note that this may be difcult to do as the bar is
secured rmly as a safety precaution.
IMPORTANT WARNING: THE FRONT BAR IS NEITHER A
RESTRAINING NOR CARRYING DEVICE.
USING THE ADJUSTABLE HANDLE
FIGURE H - ADJUSTABLE HANDLE
24. Your handle can be adjusted to multiple positions.
25. Press the centre locking button while
simultaneously moving the handle up or down.
26. Releasing the locking button will allow the handle
to lock into the next position.
14
click
E
F
click
21
19
G
push
25
H
FOOTREST ADJUSTMENT
FIGURE I - FOOTREST ADJUSTMENT
27. To adjust your footrest, simultaneously press the
two adjusting buttons on either side of the footrest
and move it up or down to the desired position.
SEAT ADJUSTMENT
FIGURE J - SEAT ADJUSTMENT
28. Your stroller seat has 4 recline positions.
29. To recline the seat simply lift the recline handle
located on the back of the seat and ease the seat
down into the required position.
30. For seat incline, gently push the seat upward into
the desired upright position. It is not necessary to
lift the recline handle.
NOTE: SPECIAL CARE MUST BE TAKEN WHEN
ADJUSTING THE SEAT POSITION WITH A CHILD IN
THE STROLLER.
HOOD
FIGURE K- HOOD INSTALLATION
31. Insert the plastic hood legs into the
corresponding housing on either side of the
stroller frame.
32. To remove your hood; Feeling the side of the
nylon housing that sits below the frame at each
side (facing inward), locate the hood release tabs.
33. Press the hood release tabs inward while
simultaneously lifting the hood upward. Repeat for
the other side.
FIGURE L- USING THE HOOD
The Expanda hood unzips, increasing the size of
your standard hood to give greater coverage and
protection from the sun and weather for your child.
To open the Expanda Hood:
34. Locate the zip in the center of the Expanda Hood
and unzip completely. Gently pull the Expanda
Hood forward until it reaches its full extension
To close the Expanda Hood
35. Gently push the Expanda Hood back, allowing
the middle section to fold in on itself. Carefully zip
the Expanda Hood closed.
IMPORTANT: always take care when closing the
Expanda Hood to avoid the zipper catching on the
ENCLOSED fabric
I
push
I
click
lift
26
J
K
L
47
FOLDING YOUR STROLLER
FIGURE M - FOLDING
36. Lower the seat to the full recline position. Note: This is not
necessary for folding but will ensure that your Rebel Q stroller is at its
most compact when folded.
37. Fold the hood back against the frame.
38. Squeeze the center locking button on the handle.
39. While keeping the centre locking button depressed, press the
frame lock button rmly and push the handle inward, with a rm
downward action, past the frame lock until it engages the lock
spring. This will unlock the frame.
40. Continue to ease the chassis downward until it is fully collapsed.
FIGURE N- FRAME LOCK
41. Locate the locking clasp on the side of the stroller frame.
42. With your stroller in the closed position, swivel the clasp into
position and secure the catch over the frame rivet.
43. Your stroller is now ready for storage or transport.
HARNESS
FIGURE O - USING YOUR HARNESS
YOUR STROLLER IS FITTED WITH OUR UNIQUE MULTI POINT SAFETY
HARNESS SYSTEM. ALWAYS USE THE HARNESS, cORREcTLY FITTED AND
ADJUSTED, WITH YOUR cHILD IN THIS SEAT
TO SECURE YOUR CHILD IN THE HARNESS:
FIGURE O
44. Slide the shoulder strap buckle (1) into the housing of the
waist strap buckle (2), forming a complete buckle
45. Repeat for the opposite side.
46. Insert the completed buckle (3) in the buckle housing (4) until
it engages securely in place.
47. Repeat for the opposite side.
48. Carefully adjust the harness straps to snugly t your child
by adjusting the Sliders located on all Shoulder Straps, Waist
Straps and the Crotch Strap (5).
Your harness can be adjusted for even more comfort for smaller or
larger children by threading the harness webbing through the
adjusting ‘sliders’ in either direction, you can change the length
of the webbing thus making them tighter or looser over your
child’s torso.
The harness should be snugly tted to the baby’s body, tight
enough so that the baby cannot wriggle itself free of the straps
but loose enough so as not to cause the baby any discomfort.
TO OPEN YOUR HARNESS
49. Press down rmly on the button in the center of the buckle
housing (4). The waist and shoulder strap sections will spring
free of the buckle housing.
50. If they do not automatically release, slide the shoulder strap
buckles (1) free from the waist strap sections. This is to ensure
that they do not form a potential entrapment area.
51. Your harness will separate into 5 sections
IMPORTANT WARNING: WHEN NOT IN USE DISCONNECT SHOULDER
STRAPS FROM THE WAIST STRAP AND/OR BUCKLE.
BRAKES
FIGURE N - USING YOUR BRAKES
49. Press down on the red brake lever located on the rear axle to
simultaneously engage the brake in both rear wheels.
50. To release, simply lift the red brake lever with your foot.
IMPORTANT WARNING: ALWAYS TEST THAT THE BRAKES ARE SECURELY
ENGAGED BEFORE USE.
M
N
O
P
1
1
2
3
4
TETHER STRAP
FIGURE O - USING THE TETHER STRAP
51. Your stroller comes equipped with a Safety
Tether. Secure the strap to your wrist to stop the
stroller rolling away.
NOTE: ALWAYS USE THE TETHER STRAP WHEN A CHILD IS
IN THE STROLLER
OPTIONAL BASSINET
BASSINET ASSEMBLY
FIGURE R - CONTENTS
1. Remove the Rebel Q Bassinet from the carton and
dispose of all packaging thoughtfully.
2. Lie the bassinet on a at surface, ‘bottom’ down.
PLEASE NOTE THAT THE HOOD OF YOUR REBEL Q
BASSINET IS ATTACHED TO THE BASSINET BODY AND
CANNOT BE REMOVED.
FIGURE S - CREATING THE BASSINET BODY
3. Inset: pull back the inner lining and locate the wire
support frames.
4. Lifting the top bassinet frame slightly and using
the nger loop on each support frame, pull each
outward to create the bassinet body
5. Be sure to pull each frame as far as it can go and
lock into the stoppers found on the base of the
bassinet.
FIGURE T - DRESSING THE BASSINET
6. Fold fabrics inside out. Line up each of the press
studs.
7. Pull the harness through the slits.
8. Straighten the inner lining in the bassinet neatly.
9. Secure by wrapping the end of the lining over the
bassinet sides and end. Straighten the fabric.
Q
R
S
T
CLICK
U
V
W
X
Y
FIGURE U - ATTACHING THE FIXING FRAME
10. Turn the bassinet over.
11. Align the xing frame with the with the
corresponding housing located on either side of
the bassinet.
12. Insert the xing frame connectors into the
housing until the seat is securely ‘clicked’ into
place.
FIGURE V - INSERTING THE MATTRESS
13. The Rebel Q mattress pad is a contoured, wedge
shape to t the shape of the bassinet. Insert the
mattress into the bassinet with the thicker, wider
end to the front of the bassinet. For your baby’s
extra security and safety, The Rebel Q Bassinet
comes equipped with waist straps. To Use: Make
sure that the lap straps remain on top of the
mattress when you assemble the bassinet. Place
your baby carefully into the assembled Rebel Q
Bassinet. Always place your baby’s head at the
forward (hood) end of the bassinet. Fold the lap
straps over your baby’s waist, leaving arms free.
Secure the lap strap snugly, but not overly tight,
by gently pressing the opposing Velcro strips
together.
WARNING !: ALWAYS USE THE WAIST STRAPS WHEN
CARRYING YOUR BABY IN THE BASSINET TO AVOID BABY
SLIDING OR ROLLING.
FIGURE F - ADJUSTING THE HOOD
14. To adjust your canopy, simultaneously press the
two grey buttons on the outside of the hood frame
and move to the desired position. NOTE: When the
hood is fully extended, it is in ‘carrying mode’, and
must be tested to ensure that it is fully engaged .
FIGURE G - FOOT COVER
15. The foot cover is easily attached by wrapping it
over the bassinet sides and securing in position
with the snaps found on the sides of the hood.
FIGURE H
16. To x your bassinet to your Rebel Q frame, line
up the xing housing with the corresponding
connectors located on either side of the stroller
frame.
17. Insert the connectors into the housing and push
downwards until the bassinet is securely in place
and you hear it ‘click’.
18. To remove your bassinet, simultaneously press
the grey release buttons on either side of the xing
frame housing and lift the bassinet from the frame.
IMPORTANT WARNING: ALWAYS TEST THAT ALL LATCHES
ARE SECURELY ENGAGED BEFORE USE.
WARNING
• Follow the manufacturer’s instructions.
• Put on all the brakes whenever you park the pram/stroller.
• Do not leave children unattended
• Do not carry extra children or bags on this pram/stroller.
• Make sure children are clear of any moving parts if you adjust the pram/stroller. Otherwise they may be injured.
Remember: Your child’s safety is your responsibility
• Never use on stairs or on an escalator.
• The correct use and maintenance of this vehicle are essential
• When in the stroller a child must always wear a safety harness, correctly tted and adjusted, at all times.
• Always use the tether strap when the stroller is in use.
• Check all parts before use for breakage or fatigue. Discontinue use immediately if any part is found to be damaged or broken.
• Should the chassis become wet, dry off promptly before storing. If the pram is used near the ocean or salted roads, spray the
chassis & seat with water & dry. We recommend a rust inhibiting product should be used to prevent rust and fatigue on metal
parts.
• We recommend a rust inhibiting product should be used to prevent rust & fatigue on metal parts.
• We recommend that you wipe down axles & lubricate the wheels every 3 months. Sand & dirt can grind down axles, if you live
near the beach or a dusty environment you must wipe down the axles & wheels , then lubricate them monthly.
• Maximum load of baskets: 3.5kgs.
• Always be aware of the risks provided by re and other signicant sources of heat such as radiators, etc. which may be in the
immediate vicinity of your stroller.
• It may be unsafe to use any accessories other than Valco approved ones.
• Be sure that all clamps and buckles are securely xed and in place before use.
• Can be used from a newborn baby onwards. A bassinet or cocoon, specially designed to be used with a stroller, is
recommended when any fully reclining stroller is used with a newborn.
• Always hold the bassinet in such a way that you keep the bassinet balanced and the bassinet with the child remains in the
horizontal position.
• The bassinet is only suitable for a child that cannot sit up on its own or roll onto its side and cannot support itself on its hands
and knees.
• Only place the bassinet down on a rm, horizontal and dry surface.
• Do not allow other children to play near the bassinet unattended
• Do not use the bassinet or the stroller if any parts are broken, torn or missing
• The maximum weight of a child for which this stroller was intended is 20 kgs.
• The maximum weight of a child for which this bassinet was intended is 9kgs.
•
Never run with a newborn baby in any pram or stroller until the child can sit up unassisted (approximately 6 months).
• Do not hang shopping bags from the handle as this may affect the stroller’s stability.
• This product is intended for domestic use only. It is not intended for commercial use.
AVOID SUFFOCATION HAZARDS:
• Unlike cribs that have rigid sides, the bassinet mattress is specially designed to prevent suffocation. The mattress is designed
to be a snug t and should not exceed 30mm in thickness. Using a thicker or different sized mattress may allow a child’s
head to bet between the mattress and the side of the bassinet causing suffocation. To help prevent suffocation from
entrapment, USE ONLY THE MATTRESS PROVIDED.
• NEVER use additional mattress or padding. Use only the tted sheet provided.
CARE & MAINTENANCE
• Continued and extended exposure to sunlight and the elements can change the colours of many materials. To avoid fading,
always cover and store in a shaded area.
• DO NOT use any bleach based products to clean the Rebel Q.
• The Rebel Q can be cleaned using a damp sponge and mild detergent.
• The mattress sheet and the inner lining are both removable and may be gentle machine washed. Line dry only.
• To prevent mould or mildew always allow fabrics to dry COMPLETELY before storing. Always store in a well ventilated area.
• Should the chassis become wet, dry off promptly before storing. If this pram is used near the ocean or salted roads, spray
the chassis and seat frame with water and dry. We recommend a rust inhibiting product should be used to prevent rust and
fatigue on metal parts.
• We recommend that you wipe down axles and lubricate the wheels every 3 months. Sand and dirt can grind down axles, if you
live near the beach or in a dusty environment you must wipe down the axles and wheels then lubricate them monthly.
AXLES ARE BEST LUBRICATED WITH GREASE OR PETROLEUM JELLY. MOVING PARTS ARE BEST LUBRICATED WITH SILICONE
BASED PRODUCTS. DO NOT USE OIL BASED PRODUCTS.
In Australia/New Zealand
www.valco.com.au
In North America only
www.valcobaby.com
1 800 610 7850
Loading...