Code
Code
Commode Mod.
VC001
Commode stool Commode Mod. VC002
Product compliant
USER MANUAL
VAIMAS SRL
via Volpato, 39
36035 Marano Vicentino VI
Directive 93/42
EEC Class I Medical
Devices
Rev. 1.4
VAIMAS SRL Via Volpato, 39 36035 Marano Vicentino VI
rev.
The commode stool, VC001 chair, and VC002 chair were designed and created to
be inserted over the toilet in order to allow disabled people or those with motor
difficulties, to safely perform their bodily functions. Plus, it can be temporarily used
as a toilet in extremely urgent situations.
1. Chrome-plated steel structure
2. Backrest and seat with removable chamber pot lid
3. Chamber pot
4. Padded armrests
5. Measurements in cm:
Stool
52
70-78
60
20
90
42
46
VC001
52
94-102
60
20
90
42
46
VC002
52
100
80
20
90
42
46
COMMODE STOOL - without wheels and platform, with legs that can be adjusted
for height in 3 positions, pitch 40
VC001 - without wheels and platform, with legs that can be adjusted in 3 positions,
pitch 40, removable backrest in washable faux leather.
VC002 - with pivoting wheels Ø 80 mm (2 with brake) and plastic platform with
height-adjustable footrest
Remove the complete commode chair from the cardboard packaging
Remove any tape from the wheels and the chamber pot
To assemble the commode chair, simply follow the instructions and perform the
adjustments as follows:
Remove the screws in the backrest attachment; insert the backrest, then replace
the screws and attach them using two 8 mm spanners.
GENERAL INFORMATION
TECHNICAL DATA
VERSIONS
ASSEMBLY
VAIMAS SRL Via Volpato, 39 36035 Marano Vicentino VI
rev.
Proceed with the assembly of the armrests using a Philips screwdriver; insert the
screws in the slots and then tighten:
Legs For the Commode Stool and model VC001, it is possible to adjust the height
of the seat in three positions using the peg. To adjust the height, use your thumb
to push the peg inside the pipe and rotate slightly to move the leg into the desired
position. Make sure all four legs are positioned at the same height.
Platform Open the clamp (figure) that attaches the platform holder to the
seat leg.
Turn the platform holder outward until it reaches the ideal front
leg-rear leg axis (Figure to the side).
Tighten the clamp to safely
block the platform holder to the seat
leg.
Lower the plastic footrest
platform Adjust the height of the
platform to the desired position.
CHECKS AND
MAINTENANCE
Weekly: Check the cleanliness of the seat and the chamber pot Monthly: check
the attachment of the backrest screws.
For model VC002, check the play in the pivoting wheels, check the attachment of
the wheels to the seat shaft, using a 9 mm spanner.
ADJUSTMENTS
VAIMAS SRL Via Volpato, 39 36035 Marano Vicentino VI
rev.
On a weekly basis, clean the seat thoroughly using common detergents.
Do not use acids or abrasive products.
Whenever the patient’s capacity cannot ensure safe use of the commode chair,
they must always be aided by a person with normal motor abilities when sitting or
standing.
To make it easier for the user to sit down or stand up, lift the plastic platform;
During sitting or standing, BLOCK the rear wheels with the brake (only mod.
VC002) by stepping on the plastic bracket located on the top of the wheel.
Whenever the patient requires assistance while sitting down, the operator
must hold the seat still with their hands on the rear part (for both models);
VC002: When the patient is sitting down or standing up from the
commode, it is absolutely forbidden to rest their feet on the plastic platform!
VC002:During the transport phase, the patient must keep their feet on the
plastic platform and sit properly
Before putting the commode seat on the toilet and having the patient sit down,
remove the plastic chamber pot and padded lid.
Outside of routine maintenance, if any part should
deteriorate, contact your distributor or the
VAIMAS srl office directly. Our technicians will be available to
help.
MAXIMUM CAPACITY 90 KG
Only use as intended by the manufacturer.
Always assist the patient when standing up or sitting down.
For model VC002, brake the rear wheels when the user is standing up or sitting down.
During the standing up or sitting down phase, do not rest the feet on the plastic platform.
Any change or restoration must be approved by the manufacturer.
Any use other than that intended by the manufacturer, could harm the patient.
The manufacturer declines all responsibility for damage caused by improper use or use in a
manner not set forth in this manual.
Warning: The information contained in this document is subject to change without prior notice.
CLEANING
USE
SUPPORT
SAFETY
Loading...