VADDIO ZOOMSHOT WALLVIEW SR 999-6918-000, ZOOMSHOT WALLVIEW SR 999-6918-001, ZOOMSHOT Installation And User Manual

Installation and User Guide

VADDIO™ ZOOMSHOT™ WALLVIEW™ SR

High Definition Point of View Camera System with 19X Optical Zoom

Model Number 999-6918-000 (North America)
Model Number 999-6918-001 (International)

© 2014 Vaddio - All Rights Reserved. ZoomSHOT WallVIEW SR - Document Number 342-0651 Rev B

Zoom SHOT WallVIEW SR

TABLE OF CONTENTS

Overview .................................................................................................................................................................... 3

Unpacking: ................................................................................................................................................................. 4

Front View with Feature Call-outs .......................................................................................................................... 4

Image: ZoomSHOT HD PTZ Camera ............................................................................................................... 4

Rear Panel Connections with Feature Call-outs .................................................................................................... 5

Image: ZoomSHOT HD Camera ....................................................................................................................... 5

Quick-Connect SR Interface ...................................................................................................................................... 6

Image: Rear Panel with Feature Call-outs ........................................................................................................ 6

First Time Set-up: ...................................................................................................................................................... 6

Step By Step Installation Instructions: ................................................................................................................... 7

Image: Basic Wiring Configuration .................................................................................................................... 8

Compliance and CE Declaration of Conformity - ZoomSHOT .................................................................................. 9

Warranty Information ............................................................................................................................................... 10

ZoomSHOT WallVIEW SR General Specifications: ............................................................................................ 11

Appendix 1: Pin-outs for ZoomSHOT Camera ....................................................................................................... 12

Table EZCamera Power & HD Video RJ-45 Connector Pin-outs .................................................................... 12

Appendix 2: Pin-outs for Quick-Connect SR Interface ........................................................................................... 12

Table: DE-15 - YPbPr Pin-Out ........................................................................................................................ 12

Communication Specification .................................................................................................................................. 13

ZoomSHOT Command List (1/2) ...................................................................................................................... 13

ZoomSHOT Command List (2/2) ...................................................................................................................... 14

ZoomSHOT Inquiry List (1/1) ........................................................................................................................... 15

ZoomSHOT WallVIEW SR System Document Number 342-0651 Rev B Page 2 of 16

Zoom SHOT WallVIEW SR

prop

O

VERVIEW

:
The Vaddio ZoomSHOT HD camera produces amazing results for
small, medium and large room applications. Anywhere that a Point­of-View or stationary camera can be used alone or in conjunction
with a Vaddio PTZ camera to simplify camera coverage and preset
positioning, the ZoomSHOT is the answer.

Essentially, the ZoomSHOT is a low cost pan/tilt/zoom camera,
where the pan and tilt are adjusted manually. However, unlike
security-type stationary cameras, the ZoomSHOT is equipped with a
19X optical power zoom lens that produces a horizontal field of view
ranging from 58º on the wide end to 3.1º on the tele end in a HD 16:9
format.

ZoomSHOT HD is a camera with a unique pedigree. Designed from
the ground up, this HD camera uses the Vaddio EZCamera™ Cat-5
wiring standard for video, power and control. Using HSDS™ (high
speed differential) video outputs over Cat-5 cable, the ZoomSHOT
sports a wide range of video resolutions that are selectable from the

Image: ZoomSHOT HD Camera

rear panel; from 480p/59.94-YPbPr up to and including 1080p/60.
The HSDS processing allows delivery of the HD video signals up to
150’ (45.72m).

Choose between three (3) IR frequencies for the Vaddio IR Shot
Commander to allow multiple cameras to be locally IR controlled with
a single remote control. The ZoomSHOT also has an OSD (on
screen display) for easy set-up and basic image control that’s
accessible with the IR remote. Up to six (6) camera zoom presets
can be programmed and recalled via the remote or RS-232 (up to 16
zoom presets with RS-232). IR signal forwarding is also included.

ZoomSHOT is paired with the tried-and-true Quick-Connect SR
Interface in this package which represents a super-high value and a
very low price. So breathe easy, and try a ZoomSHOT today!

Image: ZoomSHOT Rear Panel

Intended Use:

Before operating the device, please read the entire manual thoroughly. The system was designed, built and
tested for use indoors with the power supply provided. The use of a power supply, other than the one provided, or
outdoor operation has not been tested and could damage the device and/or create a potentially unsafe operating
condition.

Important Safeguards:

Read and understand all instructions before using. Do not operate any device if it has been dropped or
damaged. In this case, a Vaddio technician must examine the product before operating. To reduce the risk of
electric shock, do not immerse in water or other liquids and avoid extremely humid conditions.

Use only the power supply provided with the system. Use of any unauthorized
power supply will void any and all warranties.

Please do not use “pass-thru” type RJ-45 connectors. These pass-thru type connectors do not
work well for professional installations and can be the cause of intermittent connecti ons which
can result in the RS-232 control line failing and locking up, and/or compromising the HSDS (high
speed differential) signals. For best results please use standard RJ-45 connectors and test all
cables for

er pin-outsprior to use and connection to Vaddio product.

Save These Instructions:

The information contained in this manual will help you install and operate your product. If these instructions are
misplaced, Vaddio keeps copies of Specifications, Installation and User Guides and most pertinent product
drawings for the Vaddio product line on the Vaddio website. These documents can be downloaded from

www.vaddio.com free of charge.

ZoomSHOT WallVIEW SR System Document Number 342-0651 Rev B Page 3 of 16

Zoom SHOT WallVIEW SR

U

NPACKING

Carefully remove the product and all of the included parts from the packaging.
Identify the following parts for each camera:

ZoomSHOT WallVIEW SR Camera System (North America):

Part Number: 999-6918-000

 One (1) ZoomSHOT HD Camera (998-6918-000)
 One (1) Vaddio IR SHOT Commander Remote
 One (1) Quick-Connect SR Interface
 One (1) 3-Position Phoenix-type Connector for IR Forwarding
 One (1) 24 VDC, 2.0 A Power Supply with Power Cord for North America
 One (1) Thin Profile Wall Mount with Mounting Hardware
 One (1) EZCamera™ Control Adapter (RJ-45-F to DB-9-F)

 Documentation

ZoomSHOT WallVIEW SR Camera System (International):

Part Number: 999-6918-001

 One (1) ZoomSHOT HD Camera (998-6918-000)
 One (1) Vaddio IR SHOT Commander Remote
 One (1) Quick-Connect SR Interface
 One (1) 3-Position Phoenix-type Connector for IR Forwarding
 One (1) 24 VDC, 2.0 A Power Supply
 One (1) Euro Power Cable
 One (1) UK Power Cable
 One (1) Thin Profile Wall Mount with Mounting Hardware
 One (1) EZCamera™ Control Adapter (RJ-45-F to DB-9-F)
 Documentation

Front View with Feature Call-outs

Image: ZoomSHOT HD PTZ Camera

1) Lens: 19X Optical Zoom Lens

2) IR Sensor and Power LED: The IR sensor for the IR Shot Commander Remote is located here. In a

separate opening, a blue LED power light and a red LED tally resides (turns purple on boot up).

3) The Yoke: For manual pan and tilt. Tilt range is ± 30° and Pan is limited to the service loop of the cabling.

4) The Aluminum Base and Steel Cylindrical Body: Please don’t drop it on your foot, it’s fairly substantial.

5) Logo: Really Cool Logo Badge (RCLB). The RCLB is affixed to the base in a recessed ovoid area.

:

①

②

③

④

⑤

ZoomSHOT WallVIEW SR System Document Number 342-0651 Rev B Page 4 of 16

Zoom SHOT WallVIEW SR

Rear Panel Connections with Feature Call-outs

Image: ZoomSHOT HD Camera

①

③

②

④

1) RS-232 & IR Out: The RS-232 accepts modified VISCA protocol for camera control, as well as transmits IR

signaling received by the front IR receiver, which can be transmitted to third party devices.

2) EZ Power/Video Port:

This RJ-45 connector is only used with the Quick-Connect SR, Quick-Connect DVI-D/HDMI SR Interface, Quick­Connect USB and USB Mini Interfaces to supply power and return HSDS (differential) video from the camera
over Cat-5 cable up to distance of 150’ (45.72m).

3) Dip Switch Settings:

Settings for IR remote frequency, IR receiver on/off, image flip, test bars and defaults can be configured on these
switches. See the Switch Settings page for additional information. The dip switch settings are as follows:

Dip Switch Function

1 Up = IR1, Down = IR2
2 Up = IR 1 or 2, Down = IR3
3 Up=IR ON, Down = IR OFF
4 Up = Normal Image, Down = Image Flip
5 Test Bars
6 Update Position - Leave UP unless updating firmware

All Down Reset to Defaults - with power cycle

A rotary switch allows the user to choose the component HD output video resolution and format. See the HD
Video Select Rotary Switch Settings are as follows:

Rotary

0

1 1080i/59.94 9 --
2 1080p/59.94 A --
3 -- B --
4 720p/50 C --
5 1080i/50 D --
6 1080p/50 E 1080p/29.97
7 480p/59.94 F 1080p/25

Resolutions

720p/59.94 8 576p/59.94

Rotary

Resolutions

4) HD Video Select:

ZoomSHOT WallVIEW SR System Document Number 342-0651 Rev B Page 5 of 16

Zoom SHOT WallVIEW SR

QUICK-CONNECT SR INTERFACE

Image: Rear Panel with Feature Call-outs

1) Power Input:

5.5mm OD x 2.5mm ID coaxial connector for the provided PowerRite 24 VDC, 2.0 Amp power supply.

2) EZCamera Power & HD Video:

A single Cat-5 connection between the EZCAMERA POWER & HD VIDEO RJ-45 connector and the camera’s
EZ Power HD Video Port on the HD-19 camera extends power and video. Power is fed to the camera and HSDS
video is returned from the camera on the same Cat-5.

3) HD Video Output:

DE-15 connector outputs the YPbPr analog component HD video, which was extended from the camera over
Cat-5 cable. SD video resolutions (Y/C and CVBS formats) are not supported by the Quick-Connect SR
Interface, however analog component SD video is supported.

4) IR Output:

With the IR pass-thru turned ON (see camera dip switch settings), IR from third-party IR remote controls can be
sent through the ZoomSHOT camera to third-party equipment, such as hardware videoconferencing codecs. IR
can be used as either modulated (through the air) or non-modulated (wired) signals).

5) RS-232 Input & Output Jacks:

These RJ-45 connectors allow an external controller (beware of upcoming shameless plug) like the
ProductionVIEW™ Precision Camera Controller to route through the Quick-Connect SR for ease of cabling.

①

② ④

③

⑤

FIRST TIME SET-UP:

The ZoomSHOT was designed to be very easy to use and operate. There is documentation at the back of this
manual for pin-outs of the connectors on the Quick-Connect and camera.

Before Installing:

 Choose camera mounting location, paying close attention to camera viewing angles, lighting conditions,

possible line of site obstructions, and checking for in-wall obstructions where the camera is to be mounted.
Always pick a mounting location that will optimize the performance of the camera.

 The Thin Profile Wall Mount for the ZoomSHOT can be mounted directly to a 1-gang wall box or can be

mounted using only dry wall anchors.

 For Power/Video and RS-232 signals, use standard Cat-5 cable (568B termination and real RJ-45

connectors) from the EZ-POWER VIDEO and RS-232 ports on the back of the ZoomSHOT to the Quick-

Connect SR Interface. The EZ-POWER VIDEO jack on the camera is highlighted red as a reminder that

there is 24 VDC power on that Cat-5 cable.

ZoomSHOT WallVIEW SR System Document Number 342-0651 Rev B Page 6 of 16

Zoom SHOT WallVIEW SR

Step By Step Installation Instructions:
Step 1: After determining the optimum location of the camera, route, mark and test the two (2) Cat-5 cables from

the camera to the Quick-Connect SR Interface located at the head-end. The two Cat-5e cables should feed­through the hole located on the rear flange of the Thin Profile Wall Mount. If the bracket is to be mounted on a 1­gang wall box, use the screws supplied with the wall box cover plate to attach the Thin Profile Wall Mount. If
mounting to the drywall with wall anchors, use two (2) quality wall anchors. The mounting holes are slotted and
are 90° opposing to provide easy leveling. Level the mount and tighten the mounting screws.

Step 2:

Using the HD VIDEO SELECT rotary switch and CAMERA SETTINGS dip switches on the back of the camera,
set up the camera’s output resolution and functional preferences. There are tables on previous pages that
identify the choices…maybe keep these tables handy for future use…or you can easily look them up on the

Vaddio website (vaddio.com) when needed.

On the camera:

 Set the desired HD Resolution with the rotary selection switch.
 Set the IR frequency of the camera (if it is to respond to the IR remote control).
 Set the image orientation (normal or flipped).

Step: 3: Follow the sample wiring diagram for connecting the Cat-5 cables to the ZoomSHOT and Quick-

Connect SR Interface (yep, on the next page, but read and understand the rest of these instructions especially
the next note).

NOTE: Check all Cat-5e cables for continuity in advance of the final connection. Label the

Cat-5e cables. Plugging the EZ-POWER VIDEO cable into the wrong RJ-45 may cause
damage to the camera system and void the warranty. For premise cabling, please use real
RJ-45 connectors and crimpers. Please don’t use the pull through or EZ type of RJ-45.

Step 4: Place the camera onto the camera mount and use the provided ¼”-20 screws to secure the camera to

the mount. To dress the cabling, push the extra cable back into the wall opening.

Step 5: Connect the Vaddio 24 VDC, 2.0 Amp power supply to a power outlet and to the Quick Connect SR

Interface. Power will travel down the EZ-POWER VIDEO Cat. 5 cable to the camera. The camera will boot up
and in a few seconds, HSDS (differential) video will travel back down the Cat-5 cable and be ready to accept
control information from the IR remote control or RS-232 camera controller.

To insure proper continuity of control and operation of the cameras, the RS-232 controller (control
system or joystick) should be powered on after the camera.

.

ZoomSHOT WallVIEW SR System Document Number 342-0651 Rev B Page 7 of 16

Zoom SHOT WallVIEW SR

r

Image: Basic Wiring Configuration

ZoomSHOT
Rear View

RS-232 & IR
OUT Cat-5

For Zoom &
CCU Control

24VDC, 2.0 A

PowerRite Power

Supply

Note: RS-232 Control can be run through the RS-232
IN and OUT of the Quick-Connect SR Interface and is

HSDS (differential) HD Video &
24 VDC Power One (1) Cat-5 Cable

←

YPbPr (HSDS differential)

Powe

YPbPr

ProductionVIEW Precision Camera Controller

required for use with IR Forwarding.

→

Rear Panel
Quick-Connect SR Interface

HD Monitor

(Simulated HD Video Feed)

ZoomSHOT WallVIEW SR System Document Number 342-0651 Rev B Page 8 of 16

Zoom SHOT WallVIEW SR

COMPLIANCE AND CE DECLARATION OF CONFORMITY - ZOOMSHOT

Compliance testing was performed to the following regulations:

 FCC Part 15 (15.107, 15.109), Subpart B Class A
 ICES-003, Issue 4: 2004 Class A
 EN 55022 A: 2006 + A1: 2007 Class A
 KN22 2008 (CISPR 22: 2006) Class A
 KN24 2008 (CISPR 24: 1997 + A1: 2000 + A2: 2002) Class A
 EMC Directive 2004/108/EC Class A



EN 55024: A2: 2003 Class A

FCC Part 15 Compliance

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part
15, Subpart B, of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at his/her own
expense.

Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This
device must accept any interference including interference that may cause undesired operation of the device.
Changes or modifications not expressly approved by Vaddio can affect emission compliance and could void the
user’s authority to operate this equipment.

ICES-003 Compliance

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out
in the Radio Interference Regulations of the Canadian Department of Communications.
Le présent appareil numérique n’emet pas de bruits radioélectriques dépassant les limites applicables aux
appareils numeriques de la classe A préscrites dans le Règlement sur le brouillage radioélectrique édicte par le
ministère des Communications du Canada.

European Compliance

This product has been evaluated for Electromagnetic Compatibility under the EMC Directive for Emissions and
Immunity and meets the requirements for a Class A digital device. In a domestic environment this product may
cause radio interference in which case the user may be required to take adequate measures.

Standard(s) To Which Conformity Is Declared:

EMC Directive 2004/108/EC
EN 55022 A: 2006 + A1: 2007(CISPR 22:2005/A1:2005)
EN 55024: A2: 2003

 EN 61000-4-2: 1995 + Amendments A1: 1998 + A2: 2001 Electrostatic Discharge
 EN 61000-4-3: 2006 + A1: 2008 Radiated Immunity
 EN 61000-4-4: 2004 + Corrigendum 2006 Electrical Fast Transients
 EN 61000-4-5: 2006 Surge Immunity
 EN 61000-4-6: 2009 Conducted Immunity
 EN 61000-4-8: 2010 Power Frequency Magnetic Field
 EN 61000-4-11: 2004 Voltage Dips, Interrupts and Fluctuations

KN24 2008 (CISPR 24: 1997 + A1: 2000 + A2: 2002) IT Immunity Characteristics

 EN 61000-4-2 Electrostatic Discharge
 EN 61000-4-3 Radiated Immunity
 EN 61000-4-4 Electrical Fast Transients
 EN 61000-4-5 Surge Immunity
 EN 61000-4-6 Conducted Immunity
 EN 61000-4-8 Power Frequency Magnetic Field
 EN 61000-4-11 Voltage Dips, Interrupts and Fluctuations

IEC 60950-1:2005 (2nd Edition); Am 1:2009 Safety
EN 60950-1:2006+A11:2009+A1:2010+A12:2011 Safety

Class A
Immunity

ZoomSHOT WallVIEW SR System Document Number 342-0651 Rev B Page 9 of 16

Zoom SHOT WallVIEW SR

WARRANTY INFORMATION

(See Vaddio Warranty, Service and Return Policies posted on vaddio.com for complete details):

Hardware* Warranty: Two (2) year limited warranty on all parts and labor for Vaddio manufactured products. Vaddio

warrants its manufactured products against defects in materials and workmanship for a period of two years from the day of
purchase, to the original purchaser, if Vaddio receives notice of such defects during the warranty. Vaddio, at its option, will
repair or replace products that prove to be defective. Vaddio manufactures its hardware products from parts and components
that are new or equivalent to new in accordance with industry standard practices.

Exclusions: The above warranty shall not apply to defects resulting from improper or inadequate maintenance by the

customer, customers applied software or interfacing, unauthorized modifications or misuse, mishandling, operation outside the
normal environmental specifications for the product, use of the incorrect power supply, modified power supply or improper site
operation and maintenance. OEM products and products manufactured by other companies are excluded and are covered by
the manufacturer’s warranty.

Vaddio Customer Service: Vaddio will test, repair, or replace the product or products without charge if the unit is under

warranty. If the product is out of warranty, Vaddio will test then repair the product or products. The cost of parts and labor
charge will be estimated by a technician and confirmed by the customer prior to repair. All components must be returned for
testing as a complete unit. Vaddio will not accept responsibility for shipment after it has left the premises.

Vaddio Technical Support: Vaddio technicians will determine and discuss with the customer the criteria for repair costs

and/or replacement. Vaddio Technical Support can be contacted through one of the following resources: e-mail support at

[e-mail] or online at vaddio.com.

Return Material Authorization (RMA) Number: Before returning a product for repair or replacement request an RMA from

Vaddio’s technical support. Provide the technician with a return phone number, e-mail address, shipping address, product
serial numbers and original purchase order number. Describe the reason for repairs or returns as well as the date of
purchase. See the General RMA Terms and Procedures section for more information. RMA’s are valid for 30 days and will be
issued to Vaddio dealers only. End users must return products through Vaddio dealers. Include the assigned RMA number in
all correspondence with Vaddio. Write the assigned RMA number clearly on the shipping label of the box when returning the
product. All products returned for credit are subject to a restocking charge without exception.

Voided Warranty: The warranty does not apply if the original serial number has been removed or if the product has been

disassembled or damaged through misuse, accident, modifications, use of incorrect power supply, use of a modified power
supply or unauthorized repair.

Shipping and Handling: Vaddio will not pay for inbound shipping transportation or insurance charges or accept any

responsibility for laws and ordinances from inbound transit. Vaddio will pay for outbound shipping, transportation, and
insurance charges for all items under warranty but will not assume responsibility for loss and/or damage by the outbound
freight carrier. If the return shipment appears damaged, retain the original boxes and packing material for inspection by the

carrier. Contact your carrier immediately.
Products not under Warranty: Payment arrangements are required before outbound shipment for all out of warranty

products.

*Vaddio manufactures its hardware products from parts and components that are new or equivalent to new in accordance with industry standard practices.

Other General Information:
Care and Cleaning

Do not attempt to take this product apart at any time. There are no user-serviceable components inside.

 Do not spill liquids in the product
 Keep this device away from food and liquid
 For smears or smudges on the product, wipe with a clean, soft cloth
 Use a lens cleaner on the lens - not a hanky
 Do not use any abrasive chemicals.

Operating and Storage Conditions:

Do not store or operate the device under the following conditions:

 Temperatures above 40°C (104°F) or temperatures below 0°C (32°F)
 High humidity, condensing or wet environments
 In inclement weather
 In swimming pools or under waterfalls
 Dry environments with an excess of static discharge
 In orbit (vacuum issue)
 Under severe vibration

ZoomSHOT WallVIEW SR System Document Number 342-0651 Rev B Page 10 of 16

Zoom SHOT WallVIEW SR

V

V

ZoomSHOT WallVIEW SR General Specifications:

ZoomSHOT Camera System

Part Numbers

Image Sensor

ideo Output Resolutions

Lens/ Focal Length
Horizontal Viewing Angle

ideo S/N Ratio
Minimum Illumination
Serial Control Protocol
Manual Pan/Tilt Range

Preset Positions
Tally Light
Camera Connectors

HD Video Select
Camera Settings

Thin Profile Wall Mount

User Controls
Materials & Weight
Dimensions:

Quick-Connect SR Interface

Connectors

Power Supply
Dimensions (H x W x D)
Weight
Accessory

Moon in Front Page Header: Europa - Sixth closest moon of the planet Jupiter.

ZoomSHOT WallVIEW 999-6918-000 (North America)
ZoomSHOT WallVIEW 999-6918-001 (International)

1/3-Type Exmor High-speed, Progressive Scan CMOS Sensor with 1.3 Megapixels
HD: 1080/59.94/50/30/25, 1080i/59.94/50, 720p/59.94/50

SD: 480p/59.94 & 576p/50
19X Optical Zoom, F=4.5mm wide to 85mm tele end (F1.6-F2.9), Min. Focus Distance 1.0m

58.1° Wide End to 3.2° Tele End - 16:9 Format
>52 dB

0.7 LUX (F1.6, 50IRE)
RS-232 (Modified VISCA)
Pan: Limited to service loop of cabling, yoke and base are mechanical only

Tilt: ± 30°
Invertible for Ceiling Mount

Six (6) Programmed and Recalled via IR Remote, 16 Programmed and Recalled with RS-232
Available through RS-232 Control
Two (2) RJ-45 Jacks:

 EZ-Power VIDEO RJ-45 Jack for use with Quick-Connect - Supplies power to the camera and

returns differential HD video from the camera

 RS-232 RJ-45 Jack (RS-232 Communication and IR Out (with Quick-Connect -SR Interfaces

16-Position Rotary Switch: Used to set HD Video Resolution Output
6-Position Dip Switch: For IR Freq., Baud Rate 9600, Image Flip & Test Bars

16-Position Rotary Switch for Output Resolution Settings
535-2000-237 (Provided with WallVIEW Systems)

Black powder coating, Sized to fit on 1-gang wall box or drywall mounting
IR Shot Commander Remote with OSD for set-up, RS-232 Port for External Control
Aluminum & Steel, Weight = 2.75643 lbs. (1.68kg)
Tube: 3” ( 76.2mm) Diameter x 4.75” (120.65mm) Long

Base: 5.5” (139.7mm) Diameter
Overall Height: 5.5” (139.7mm) Tall

 Power Connector: 5.5mm OD, 2.5mm ID coaxial connector
 Power/Video RJ-45: Supplies power to, and differential HD video from the camera
 Video Output: DE-15 connector for HD Analog Component (YPbPr) video only (No SD Support)
 IR Output: Transmits modulated or non-modulated IR signals received from the camera’s IR

receiver

 RS-232 IN RJ-45: Accepts RS-232 from ProductionVIEW or other external control systems
 RS-232 OUT RJ-45: Sends RS-232 from Quick-Connect SR to the camera

24 VDC, 2.0 Amp
1/3 Rack Size - 1.6” (40.64mm ) H x 5.5” (139.7mm) W x 3.25” (82.5500000000001mm) D

0.45 lbs. ( 0.2041165643 kg)
Rack Mount Adapter: 998-6000-002 - Holds three (3) Quick-Connect SR Interfaces

ZoomSHOT WallVIEW SR System Document Number 342-0651 Rev B Page 11 of 16

Zoom SHOT WallVIEW SR

A

PPENDIX 1: PIN-OUTS FOR ZOOM

Table EZCamera Power & HD Video RJ-45 Connector Pin-outs

ZoomSHOT EZPOWER HD VIDEO PORT

Pin YPbPr

1 Power+
2 Power-
3 Y+
4 PB+
5 PB -
6 Y -
7 PR+
8 PR-

SHOT C

AMERA

EZ POWER

HD VIDEO

12345678

Important Note: The EZ POWER HD VIDEO RJ-45 Connector is for use with the Quick-Connect SR,
Quick-Connect DVI/HDMI SR, Quick-Connect USB and USB Mini Interfaces ONLY (568B Wiring

Standard). The video signals are differential (HSDS™) and can only be received by the interfaces
above.

ZoomSHOT Camera RS-232 Port

Pin # Function

Pin - 1 N/A
Pin - 2 N/A
Pin - 3 N/A
Pin - 4 IR Output (Diff Signal to Quick-Connect)
Pin - 5 IR Ground (Diff Signal to Quick-Connect)
Pin - 6 Digital GND
Pin - 7 RXD (from TXD of control source)
Pin - 8 TXD (to RXD of control source)

A

PPENDIX 2: PIN-OUTS FOR QUICK-CONNECT SR INTERFACE

Table: DE-15 - YPbPr Pin-Out

Pin YPbPr

1 Pr
2 Y
3 Pb
4 -
5 -
6 Pr GND
7 Y GND
8 Pb GND

9 -
10 GND
11 -
12 -
13 -
14 -
15 -

-

12345678

ZoomSHOT WallVIEW SR System Document Number 342-0651 Rev B Page 12 of 16

Zoom SHOT WallVIEW SR

COMMUNICATION SPECIFICATION

Communication Speed: 9600 bps (default)
Start bit: 1
Stop bit: 1
Data bits: 8
Parity: None
No Flow control

12345678

Pin # RJ-45 RS-232 and IR Out Pins

1) Unused

2) Unused

3) Unused

4) IR Output (Diff Signal to Quick-Connect SR)

5) IR Ground (Diff Signal to Quick-Connect SR)

6) GND (GND of IR Short Range - Pin 3)

7) RXD (from TXD of control source)

8) TXD (to RXD of control source)

NOTE: The Vaddio ZoomSHOT control protocol is similar, but not identical to the Sony® VISCA™ command set

in order to be compatible with several popular control devices. Not all VISCA commands are supported and
there are many ZoomSHOT specific commands in the following Command and Inquiry Lists.

ZoomSHOT Command List (1/2)

Command Set Command Command Packet Comments

Address Set Broadcast 88 30 01 FF Address Set (Daisy chain)
IF_Clear Broadcast 88 01 00 01 FF IF Clear
Command Cancel 8x 2p FF p:socket number(1,2)
CAM_Power On

Off(Standby)

CAM_Zoom Stop

Tele(Standard)
Wide(Standard)
Tele(Variable)
Wide(Variable)
Direct
Direct(Variable)

CAM_Focus Stop

Far(Standard)
Near(Standard)
Far(Variable)
Near(Variable)
AutoFocus
ManualFocus
Auto/Manual
Direct

CAM_WB Auto

Manual
One Push WB

CAM_RGain Reset

Up
Down
Direct

CAM_BGain Reset

Up
Down
Direct

CAM_AE Full Auto

Manual

CAM_Iris Reset

Up
Down
Direct

CAM_Gain Reset

Up
Down
Direct

CAM_Bright Reset

Up
Down
Direct

CAM_Backlight On

Off

CAM_Aperture Reset

Up
Down
Direct

8x 01 04 00 02 FF
8x 01 04 00 03 FF
8x 01 04 07 00 FF
8x 01 04 07 02 FF
8x 01 04 07 03 FF
8x 01 04 07 2p FF
8x 01 04 07 3p FF
8x 01 04 47 00 0p 0q 0r FF
8x 01 7E 01 4A 0v 0p 0q 0r 0s FF
8x 01 04 08 00 FF
8x 01 04 08 02 FF
8x 01 04 08 03 FF
8x 01 04 08 2p FF
8x 01 04 08 3p FF
8x 01 04 38 02 FF
8x 01 04 38 03 FF
8x 01 04 38 10 FF
8x 01 04 48 0p 0q 0r 0s FF
8x 01 04 35 00 FF
8x 01 04 35 03 FF
8x 01 04 35 05 FF
8x 01 04 03 00 FF
8x 01 04 03 02 FF
8x 01 04 03 03 FF
8x 01 04 43 0p 0q 0r 0s FF
8x 01 04 04 00 FF
8x 01 04 04 02 FF
8x 01 04 04 03 FF
8x 01 04 44 0p 0q 0r 0s FF
8x 01 04 39 00 FF
8x 01 04 39 03 FF
8x 01 04 0B 00 FF
8x 01 04 0B 02 FF
8x 01 04 0B 03 FF
8x 01 04 4B 00 00 0p 0q FF
8x 01 04 0C 00 FF
8x 01 04 0C 02 FF
8x 01 04 0C 03 FF
8x 01 04 4C 00 00 0p 0q FF
8x 01 04 0D 00 FF
8x 01 04 0D 02 FF
8x 01 04 0D 03 FF
8x 01 04 4D 00 00 0p 0q FF
8x 01 04 33 02 FF
8x 01 04 33 03 FF
8x 01 04 02 00 FF
8x 01 04 02 02 FF
8x 01 04 02 03 FF
8x 01 04 42 00 00 0p 0q FF

Power On/Off

p:(0-Slow to 7-Fast)

pqrs: Zoom Position*
v: zoom speed

pqrs: Focus position*
Normal Auto (Auto Tracing WB)
Manual White Balance
One Push White Balance Mode

pqrs:00-ffff

pqrs:00-ffff
Auto Exposure Mode
Manual Control Mode

pq(0x00-0x11)

pq(0x00-0x11)

pq(0x00-0x24)

pq(0x00-0x1F)

ZoomSHOT WallVIEW SR System Document Number 342-0651 Rev B Page 13 of 16

Zoom SHOT WallVIEW SR

ZoomSHOT Command List (2/2)

Command Set Command Command Packet Comments

CAM_Memory Reset

Set

Recall
CAM_IDWrite 8x 01 04 22 0p 0q 0r 0s FF pqrs:0x0000 – 0xFFFF
IR_Receive On

Off
CAM_LR_Reverse On

Off
CAM_PictureEffect Color

B&W
Tally On

Off
Preset Pan Speed Zoom Speed 81 01 7E 01 0B 00 00 ZZ FF ZZ:Zoom Speed(0-7);
BLK.Enhance No support No support No support
GMA.Enhance Gamma 8x 01 7E 54 00 00 0p 0q FF pq: Gamma (0x00-0x10)
CRM.Enhance Chroma 8x 01 7E 55 00 00 0p 0q FF pq: Chroma (0x00-0x64)
KNE.Enhance Knee No support No Support
DIS.Enhance Digital Image

Stabilizer
SNR.Enhance Digital Noise

Reduction
AGC.Enhance AGC Mode 8x 01 7E 59 00 FF

CAM_Shutter Reset

Up

Down

Direct
CAM_ICR ICR On

ICR Off

8x 01 04 3F 00 0p FF
8x 01 04 3F 01 0p FF
8x 01 04 3F 02 0p FF

8x 01 06 08 02 FF
8x 01 06 08 03 FF
8x 01 04 61 02 FF
8x 01 04 61 03 FF
8x 01 04 63 00 FF
8x 01 04 63 04 FF
8x 01 7E 01 0A 00 02 FF
8x 01 7E 01 0A 00 03 FF

8x 01 7E 57 02 FF
8x 01 7E 57 03 FF
8x 01 7E 58 02 FF
8x 01 7E 58 03 FF

8x 01 7E 59 01 FF
8x 01 7E 59 02 FF
8x 01 7E 59 03 FF
8x 01 7E 59 04 FF
8x 01 04 0A 00 FF
8x 01 04 0A 02 FF
8x 01 04 0A 03 FF
8x 01 04 4A 00 00 0p 0q FF
8x 01 04 01 02 FF
8x 01 04 01 03 FF

p:Memory No(=0-0xF)

Mirror (Horizontal) on
Mirror (Horizontal) off

On
Off
On
Off
Off
Low
Medium
High
Manual

pq(0x00-0x23)
ICR On – Cut filter out B&W
ICR Off – Cut filter in Color

*Zoom and Focus Data:

CAM_Zoom: Range(0x000–0x6B3)
CAM_Focus: Range (0x0000-0xC000) dependent on Zoom Position

ZoomSHOT WallVIEW SR System Document Number 342-0651 Rev B Page 14 of 16

Zoom SHOT WallVIEW SR

ZoomSHOT Inquiry List (1/1)

Inquiry Command Command Response Packet Comments

CAM_PowerInq 8x 09 04 00 FF y0 50 02 FF

CAM_ICRModeInq 8x 09 04 01 FF y0 50 02 FF

CAM_IDInq 8x 09 04 22 FF y0 50 0p 0q 0r 0s FF pqrs:0x0000 – 0xFFFF
CAM_BacklightModeInq 8x 09 04 33 FF y0 50 02 FF

CAM_WBModeInq 81 09 04 35 FF y0 50 00 FF

CAM_FocusModeInq 8x 09 04 38 FF y0 50 02 FF

CAM_AEModeInq 8x 09 04 39 FF y0 50 00 FF

CAM_MemoryInq 8x 09 04 3F FF y0 50 0p FF p:Preset 0-0xf
CAM_ApertureInq 8x 09 04 42 FF y0 50 00 00 0p 0q FF Pq:x00-0x1F
CAM_RGain 8x 09 04 43 FF y0 50 0p 0q 0r 0s FF pqrs:00-ffff
CAM_BGain 8x 09 04 44 FF y0 50 0p 0q 0r 0s FF pqrs:00-ffff
CAM_ZoomPosInq 8x 09 04 47 FF y0 50 00 0p 0q 0r FF pqr(0x00-0x6B3)
CAM_FocusPosInq 8x 09 04 48 FF y0 50 0p 0q 0r 0s FF pqrs: Focus Position
CAM_ShutterPosInq 8x 09 04 4A FF y0 50 00 00 0p 0q FF pq(0x00-0x23)
CAM_Iris 8x 09 04 4B FF y0 50 00 00 0p 0q FF pq(0x00-0x11)
CAM_Gain 8x 09 04 4C FF y0 50 00 00 0p 0q FF pq(0x00-0x24)
CAM_Bright 8x 09 04 4D FF y0 50 00 00 0p 0q FF pq(0x01-0x64)
CAM_LR_Reverse 8x 09 04 61 FF y0 50 02 FF

CAM_Freeze 8x 09 04 62 FF y0 50 02 FF

CAM_PictureEffect 8x 09 04 63 FF y0 50 00 FF

IR_ReceiveInq 8x 09 06 08 FF y0 50 02 FF

TallyInq 8x 09 7E 01 0A FF y0 50 02 FF

PresetSpeedInq 8x 09 7E 01 0B FF y0 50 00 00 rr FF rr:Zoom 0x00-0x07
BLK.Enhance No support No support No support
GMA.Enhance 8x 09 7E 54 FF y0 50 00 00 0p 0q FF pq: Gamma (0x00-0x10)
CRM.Enhance 8x 09 7E 55 FF y0 50 00 00 0p 0q FF pq: Chroma (0x00-0x64)
KNE.Enhance No support No Support No support
DIS.Enhance 8x 09 7E 57 FF y0 50 02 FF

SNR.Enhance 8x 09 7E 58 FF y0 50 02 FF

AGC.Enhance 8x 09 7E 59 FF

y0 50 03 FF

y0 50 03 FF

y0 50 03 FF

y0 50 03 FF
y0 50 05 FF

y0 50 03 FF

y0 50 03 FF
y0 50 0A FF
y0 50 0B FF

y0 50 03 FF

y0 50 03 FF

y0 50 04 FF

y0 50 03 FF

y0 50 03 FF

y0 50 03 FF

y0 50 03 FF
y0 50 00 FF
y0 50 01 FF
y0 50 02 FF
y0 50 03 FF
y0 50 04 FF

On
Off(Standby)
On - ICR filter Out
Off – ICR filter In

On
Off
Auto
Manual
One Push WB
Auto
Manual
Auto Exposure Mode
Manual Control Mode
Shutter Priority Mode
Exposure Priority Mode

On
Off
On
Off
Off
B&W
On
Off
On
Off

On
Off
On
Off
Off
Low
Medium
High
Manual AGC Gain

ZoomSHOT WallVIEW SR System Document Number 342-0651 Rev B Page 15 of 16

Zoom SHOT WallVIEW SR

***Manual AGC Gain: 0:0dB, 1:3dB, 2:6dB, 3:9dB, 4:12dB, 5:15dB, 6:18dB, 7:21dB, 8:24dB, 9:27dB, 10:30dB, 11:33dB,

12:36dB, 13:39dB & 14:42dB

©2014 Vaddio - All Rights Reserved. Reproduction in whole or in part without written permission is prohibited. Specifications and pricing are subject to
change without notice or obligation. Vaddio, ZoomSHOT, ProductionVIEW, WallVIEW, EZCamera, Quick-Connect and HSDS are trademarks of Vaddio. All

ZoomSHOT WallVIEW SR System Document Number 342-0651 Rev B Page 16 of 16

other trademarks are property of their respective owners. Document Number 342-0651 Rev B

Toll Free: 800-572-2011 ▪ Phone: [phone] ▪ FAX: [phone]

www.vaddio.com