VADDIO WallVIEW CCU HD-19, 999-6948-000AW, 999-6948-001AW, 999-6948-000, 999-6948-001 Installation And User Manual
...
A
r
INSTALLATION AND USER GUIDE
V
AADDDDIIO
V
High Definition PTZ Camera Featuring the Quick-Connect™ CCU Interface
™
O
™
Black Ve
Part Number 999-6947-000 (North America)
Part Number 999-6947-001 (International)
©2011 Vaddio - All Rights Reserved ● WallVIEW CCU HD-19 ● Document Number 324-0268 Rev. A
W
W
sion
VII
E
W
AALLL
L
V
E
rctic White Version
Part Number 999-6947-000AW (North America)
Part Number 999-6947-001AW (International)
EZIM CCU Slot Card for HD-19
W
™
™
C
C
C
U
H
U
H
C
Quick-Connect CCU Interface for HD-19
D--1199
D
WallVIEW CCU HD-19
Inside Front Cover - Blank
WallVIEW CCU HD-19 Manual 342-0268 Rev. A Page 2 of 20
WallVIEW CCU HD-19
p
WallVIEW CCU HD-19 Overview:
The WallVIEW CCU HD-19 HD camera, Quick-Connect CCU and
EZCamera™ Cat-5e cabling system using HSDS™, delivers a
system that allows for easy installation and integration. The HD-19
camera is built around a 1/3-type Exmor high-speed CMOS image
sensor with a total of 1.3 Megapixels and a 19X optical zoom lens,
making it the ideal choice for a wide range of HD video applications.
Because the camera module is built around a new, high speed
CMOS image sensor with an increased pixel aperture size, high
frame rate, high signal to noise ratio, using the column-parallel A/D
conversion method, the resolution, saturation and the sensitivity of
the sensor is increased. The HD-19 achieves improved picture
quality even in low light environments requiring a minimum
illumination rated at an astonishing 0.7 LUX (F1.6 - 50IRE).
The HD-19 is paired with the Quick-Connect CCU Interface and EZIM CCU Slot Card, which provides power,
video and control to the camera up to 500’ (152.4m) over three (3) Cat-5e cables. The Quick-Connect CCU
functions allow users to control a variety of image controls built into the camera, including iris, red and blue gain,
pedestal, knee, chroma, SmartShot™ and overall gain. The CCU also has three (3) preset scenes available for
time of day or other interesting lighting conditions.
The WallVIEW CCU HD-19 is an exceptional camera system for integration projects, since no power supply is
required at the camera location. Use the WallVIEW CCU HD-19 for high definition camera applications, such as
houses of worship, corporate boardrooms, live event production and distance-learning.
Intended Use:
Before operating the device, please read the entire manual thoroughly. The system was designed, built and
tested for use indoors, and with the provided power supply and cabling. The use of a power supply other than the
one provided or outdoor operation has not been tested and could damage the device and/or create a potentially
unsafe operating condition.
Important Safeguards:
Read and understand all instructions before using. Do not operate any device if it has been dropped or damaged.
In this case, a Vaddio technician must examine the product before operating. To reduce the risk of electric shock,
do not immerse in water or other liquids and avoid extremely humid conditions.
Use only the power supply provided with the system. Use of any
unauthorized power supply will void any and all warranties.
Save These Instructions:
The information contained in this manual will help you install and operate your product. If these instructions are
misplaced, Vaddio keeps copies of Specifications, Installation and User Guides and most pertinent product
drawings for the Vaddio product line on the Vaddio website. These documents can be downloaded from
www.vaddio.com free of charge.
WallVIEW CCU HD-19 Manual 342-0268 Rev. A Page 3 of 20
Please do not use “pass-thru” type RJ-45 connectors. These pass-thru type connectors do not
work well for professional installations and can be the cause of intermitten t connections which
can result in the RS-232 control line failing and locking up, and/ or compromising the HSDS™
signals. For best results please use standard RJ-45 connectors and test all cables for proper
in-outs prior to use and connection to Vaddio product.
WallVIEW CCU HD-19
UNPACKING:
Carefully remove the device and all of the parts from the packaging.
Unpack and identify the following parts for 999-6947-000:
One (1) ClearVIEW HD-19 HD Camera
One (1) Vaddio IR Remote Commander
One (1) Quick-Connect CCU Interface
One (1) EZIM CCU Slot Card
One (1) 36 VDC, 2.78A Power Rite™ Switching Power Supply
One (1) 998-1001-232 EZCamera Control Adapter (for control systems)
One (1) Thin Profile Wall Mount with Mounting Hardware
One (1) AC Cord Set for North America
Documentation
(Note: The 999-6947-001 Int’l Version includes the Euro and UK power cables)
ClearVIEW HD-19 PTZ Camera, Front View with Feature Call-outs:
①
④
②
③
1) Zoom Lens and Image Sensor:
The 19X optical zoom lens is built around a 1/3-Type, high-speed, progressive scan CMOS image sensor with a
total of 1.3 Megapixels for precise HD video image acquisition.
2) Red Tally Light:
A red tally light is illuminated when the camera receives a VISCA command from an external control system.
3) IR Sensors:
IR sensors are built into the front of the ClearVIEW HD-19 to receive IR signals from the IR remote control
supplied with the camera.
4) Blue Power Light:
A Vaddio blue power light is illuminated when the camera is turned on.
Compatible Switchers and Joystick Controllers:
ProductionVIEW™ HD MV
(999-5625-000)
AutoPresenter
(999-5675-000)
Precision Camera Controller
(999-5700-000)
WallVIEW CCU HD-19 Manual 342-0268 Rev. A Page 4 of 20
WallVIEW CCU HD-19
ClearVIEW HD-19 PTZ Camera, Rear View with Feature Call-outs:
⑤
⑨
⑥
⑩
⑦
⑪
⑧
5) RS-232 IN & IR Out:
The RS-232 accepts modified VISCA protocol for camera control, as well as transmits IR signaling received by
the IR receivers, which can be transmitted to third party devices.
6) Dip Switch Settings:
Settings for IR remote, baud rate, SD output format, and image flip can be configured on these switches. See
page 5 for additional information on switch settings.
7) HD Video Select:
A rotary switch allows the user to choose the component HD output video resolution and format. See page 6 for
additional information on switch settings.
8) 12 VDC Input:
Power input for the standard, ClearVIEW HD-19 camera power supply.
9) YPbPr Output:
Component HD video is fed through the DB-15 connector. YPbPr and Composite signals are simultaneous. This
is an HD camera and the SD signals are down converted and are really not the sweet spot of this camera.
9) Composite Video (CVBS) Output:
The CVBS output feeds out SD video signals and is configurable with the dip switches to choose between
480i/NTSC or 576i/PAL in 4:3 formats. Squeeze and letterbox modes are also available (see dipswitches 6&7).
11) EZ Power/Video Port:
This RJ-45 connector is only used with the Quick-Connect SR Interface and the Quick- Connect DVI-D/HDMI SR
Interface to supply power and return HSDS video from the camera.
12) Slot for Optional Cards:
Optional slot cards can be plugged into the ClearVIEW HD-19 camera (the HD-SDI and the EZIM CCU Slot Cards
are available).
WallVIEW CCU HD-19 Manual 342-0268 Rev. A Page 5 of 20
⑫
WallVIEW CCU HD-19
Quick-Connect CCU for HD-19, Front Panel Controls (left to right):
Tally Light:
The blue LED tally light on the front panel is tied to the tally contacts on the rear panel allowing the user to easily
track which camera interface is being used in a multi-camera system by supplying a simple contact closure.
LCD Display:
Backlit (blue) display indicates which parameter (iris, detail, etc.) is being adjusted. When a rotary encoder is
moved, the name of the control being adjusted and the value of that assigned parameter will be displayed.
Quick-Connect CCU Controls (left to right - magnified):
Scenes A, B & C:
Three camera adjustment scenes (A, B & C) can be stored into microprocessor memory. When lit (backlit blue
SPDT Button), the scene is activated. To store a scene, the user adjusts the controls and touches and holds the
scene button down until the button blinks.
Detail: The Detail control sharpens or softens objects in the frame. This control works well to sharpen text.
Red & Blue Gain Controls: The Red and Blue Gain encoders adjust the red and blue gain of the signal when
AWB is disengaged.
AWB: The Automatic White Balance controls/adjusts the color levels automatically when engaged. Turn off
AWB to manually adjust the Red and Blue levels, as well as Red, Green and Blue Enhance.
OPWB: One Push White Balance is not operable in this release
Gamma, Chroma and Brightness Control:
Gamma adjusts the overall brightness of an image. Chroma controls the color of the image being acquired
without affecting brightness. The brightness control governs the overall brightness of the image.
SHIFT: Pressing Shift illuminates the button and changes the Gamma, Chroma and Brightness Control to Digital
Image Stabilization, Shutter Control and Noise reduction. Digital Image stabilization works well if the camera is
hand-held or the surface where the camera is mounted has vibration (front of a church balcony). NOTE: When
using a joystick for control of the camera, leave image stabilization off because the subsampled window if the
video image will cause delay and is not going to allow an operator to be very precise with the cam era movement
and joystick. Shutter adjustments are 1/30 to 1/500. For most applications 1/60 will work fine. Noise Reduction
can be on or off and will help reduce the noise produced by sub optimum conditions.
Auto Iris: The Auto Iris mode automatically adjusts the iris and gain of the camera. To manually adjust the iris or
gain, turn off this control. With auto Iris engage, the SmartShot (AGC Gain Limit) can be set to off, low, med, and
high. SmartShot limits the ACG Gain to avoid poor image reproduction in suspect lighting conditions).
Manual Iris: The Manual Iris control allows the user to set the iris manual to one of the settings available.
Gain: The Gain control boosts the signal level when the iris is open all the way, and there is not enough lighting
available. To manually adjust the Gain, Auto Iris must be off.
WallVIEW CCU HD-19 Manual 342-0268 Rev. A Page 6 of 20
Loading...