VADDIO WallVIEW CCU HD-18 HD-SDI Installation And Manual

Installation and Guide

Cameras and Electronic Product for Integrators

Vaddio™ WallVIEW™ CCU HD-18 HD-SDI

High-Definition HD-18 PTZ Camera featuring the EZIM HD-SDI Slot
Card and Quick-Connect CCU

Model Number 999-6908-000W (North America)
Model Number 999-6908-001W (International)
Arctic White Version

EZIM HD-SDI Card for HD-18

Model Number 999-6908-000 (North America)
Model Number 999-6908-001 (International)

Quick-Connect CCU for HD-18

©2010 Vaddio - All Rights Reserved. WallVIEW CCU HD-18 SDI - Document Number 341-988 Rev. A

WallVIEW CCU HD-18 HD-SDI

WallVIEW CCU HD-18 HD-SDI Overview

Figure 1: Quick-Connect HD-18 CCU

With the WallVIEW CCU HD-18 HD-SDI PTZ camera and CAT 5e cabling system, Vaddio delivers a
solution that allows for easy installation and integration and ultimate flexibility for the most demanding of
users. The camera is built around a 1.3 megapixel, 1/3” CCD with an 18x optical zoom lens, making it
the ideal choice for a wide range of high definition video applications. The HD-SDI output of the included
HD-SDI Slot Card can be configured as either HD (720p@59.94/50Hz, 1080i@59.94/50Hz or
1080p@60/59.94/50/30/250Hz (yep, it’s 3Gb/s capable for HD-SDI outs), or SD (480i/29.97 or 576i/25).

Because the camera module is built around a CCD image sensor, the HD-18 is excellent in low-light
situations, with a 1.8 LUX rating. In addition, the video signal to noise ratio output of the camera is
greater than 50dB, delivering clean, crisp, and clear video. The multi-element motorized zoom lens
allows WallVIEW CCU HD-18 HD-SDI to capture a wide angle of view (55.2°) enough to view everyone
at a conference room table, as well as capture an individual from a long distance (3.2°). The zoom range
provides greater flexibility for a wide variety of applications. The pan range of the HD-18 is ±170 and tilt
range is -30 to +90 degrees.

Vaddio’s Quick-Connect CCU Power and Control Interface and EZIM HD-SDI Slot Card are part of this
system. The CCU provides power and control up to 500 feet over two (2) CAT 5e cables. The CCU
allows users to control a variety of image controls built into the camera, including iris, red and blue gain,
pedestal, knee, gamma, chroma and gain. The HD-SDI/SDI signal with 3Gb/s compatible transmitter are
returned over a single coax cable. To summarize, the wiring out to this camera system is two (2) CAT 5e
cables and one coax.

The WallVIEW CCU HD-18 HD-SDI is an exceptional camera system for integration projects, since no
power supply is required at the camera location. Use the WallVIEW CCU HD-18 HD-SDI for high
definition camera applications, such as houses of worship, corporate boardrooms, live event production
and distance-learning.

Intended Use:

Before operating the Vaddio WallVIEW CCU HD-18 HD-SDI, please read the entire manual thoroughly.
The system was designed, built and tested for use indoors, and with the provided power supply and
cabling. The use of a power supply other than the one provided or outdoor operation has not been tested
and could damage the camera and/or create a potentially unsafe operating condition.

Important Safeguards:

Read and understand all instructions before using. Do not operate any device if it has been dropped or
damaged. In this case, a Vaddio technician must examine the product before operating. To reduce the
risk of electric shock, do not immerse in water or other liquids and avoid extremely humid conditions.

Save These Instructions:

The information contained in this manual will help you install and operate your Vaddio WallVIEW CCU
HD-18 HD-SDI. If these instructions are misplaced, Vaddio keeps copies of Specifications, Installation
and User Guides and most pertinent product drawings for the Vaddio product line on the Vaddio website.
These documents can be downloaded from www.vaddio.com

Use only the power supply provided with the WallVIEW CCU HD-18 HD­SDI system. Use of any unauthorized power supply will void any and all
warranties.

Please do not use the “pass-thru” RJ-45 type connector. Please use
standard RJ-45 connectors for best results.

free of charge.

WallVIEW CCU HD-18 HD-SDI Manual 341-988 Rev. A Page 2 of 26

WallVIEW CCU HD-18 HD-SDI

UNPACKING:

Carefully remove the device and all of the parts from the packaging.
Unpack and identify the following parts:

• One (1) ClearVIEW HD-18 PTZ Camera

• One (1) Quick-Connect CCU Interface for HD-18

• One (1) IR Remote Control

• One (1) EZIM HD-SDI Slot Card for HD-18

• One (1) Wall Mount and Hardware

• One (1) RJ-45 to DB-9 Adapter

• One (1) Vaddio PowerRite 36 VDC, 2.78 Amp Power Supply

• One (1) AC Cord Set (US - North America - or - UK and Europe - International)

• Documentation and Manuals

THE COMPONENTS:

• The Camera

Figure 2: ClearVIEW HD-18
PTZ Camera (front)

1

3

2 4

1. Camera – A 1/3”, 1.3 megapixel HD image sensor is combined with an 18x optical zoom lens, for
capturing high-quality video.

2. Tally Light – A tally light is illuminated when the camera receives a VISCA command or from the
CCU tally port on the back of the Quick-Connect CCU.

3. IR Sensors – Dual IR sensors are built into the front of the WallVIEW CCU HD-18 HD-SDI to
receive IR signals from the IR remote control supplied with the camera.

4. Power Light – A power light is illuminated when the camera is turned on.

Compatible Switchers and Joystick Controllers (not included in this package):

ProductionVIEW HD-SDI

(999-5650-000/001)

Precision Camera Controller

(999-5700-000/001)

WallVIEW CCU HD-18 HD-SDI Manual 341-988 Rev. A Page 3 of 26

WallVIEW CCU HD-18 HD-SDI

The Components (continued)

Figure 3: WallVIEW HD-18 camera (back)

5

9

6

10

7

11

8

Rear of WallVIEW HD-18

5. RS-232 In & IR Out – The RS-232 accepts modified VISCA™ protocol for camera control, as well
as transmits IR signaling received by the IR receivers, which can be transmitted to third party
devices.

6. DIP Switch Settings – Settings for IR remote, baud rate, SD output format, image flip can be
configured on these switches. See page 6 for additional information switch settings.

7. HD Video Select - A rotary switch allows the user to choose the component HD output video
resolution and format. See page 6 for additional information on switch settings.

8. 12 VDC Input - NOTE: The power input is not used with the WallVIEW HD-18 system. This is only
used on the standard, ClearVIEW HD-18 camera.

9. YPbPr Video Output - Component HD video is fed through the DB-15 connector.

10. SD Video Output - Standard definition video is fed through the BNC connector.

11. EZ Camera Port - This port is not used in the CCU/HD-SDI Configuration

12. Slot for Optional Cards - Optional slot cards can be plugged into the WallVIEW HD-18 camera
through the slot in the back of the camera base…like the EZIM HD-SDI Slot Card.

IMPORTANT SAFEGARD

Do not insert or remove the EZIM HD-SDI Slot Card into an HD-18
Camera when the camera is powered ON. Detach all power
connectors before installing or removing the EZIM HD-SDI Slot Card.

12

WallVIEW CCU HD-18 HD-SDI Manual 341-988 Rev. A Page 4 of 26

WallVIEW CCU HD-18 HD-SDI

The Components (continued)

• Quick-Connect CCU

Front Panel Controls (left to right):

Figure 4: Quick-Connect HD-18 CCU Front Panel

Tally Light:

The blue LED tally light on the front panel is tied to the tally contacts on the rear panel allowing the user
to easily track which camera interface is being used in a multi-camera system by supplying a simple
contact closure (i.e. from ProductionVIEW HD-SDI or Precision Camera Controller).

LCD Display:

Backlit (blue) display indicates which parameter (iris, detail, etc.) is being adjusted. When a rotary
encoder is moved, the name of the control being actuated and the value of that assigned parameter will
be displayed.

Scenes A, B & C:

Three camera adjustment scenes (A, B & C) can be stored into microprocessor memory. When lit (backlit
blue SPDT switch), the scene is activated. To store a scene, the user adjusts the controls and touches
and holds the scene button down until the button blinks. To clear a scene setting, press the two other
Scene buttons simultaneously, and hold until “Scene _ Cleared” is displayed.

Detail:

The Detail control sharpens or softens objects in the frame.

Red & Blue Gain Controls:

The Red and Blue Gain encoders adjust the red and blue gain of the signal when AWB is disengaged.

AWB:

The Automatic White Balance controls/adjusts the color levels automatically when engaged. Turn off
AWB to manually adjust the Red and Blue levels, as well as Red, Green and Blue Enhance.

SHIFT:

Pressing Shift illuminates the button and changes the Pedestal adjustment knob to Knee adjustment.
Knee adjustment allows bright objects that are easily overexposed to be reproduced more accurately.
Pressing the Shift button a second time turns the light off, and the knob reverts to Pedestal adjustment.

Pedestal / Knee, Chroma & Gamma:

The Pedestal adjustment controls the absolute black level of an image. Chroma controls the overall color
of the image being captured. Gamma adjusts the overall brightness of an image. See SHIFT for
information on Knee.

Auto Iris:

The Auto Iris mode automatically adjusts the iris and gain of the camera. To manually adjust the iris or
gain, turn off this control.

Manual Iris:

The manual iris control allows the user to set the iris manually to one of the 18 settings available.

Gain:

Gain control boosts the signal level when the iris is open all the way, and there is not enough lighting
available. To manually adjust the gain Auto Iris must be off.

WallVIEW CCU HD-18 HD-SDI Manual 341-988 Rev. A Page 5 of 26

WallVIEW CCU HD-18 HD-SDI

The Components (continued)
Rear Panel Connections and Controls (Left to Right):

+ G

Figure 5: Quick-Connect HD-18 CCU Rear Panel

Power Supply Input:

36V 2.78 Amp power supply on a 5.5mm OD x 2.5mm ID connector. Only use the power supply
provided.

Power on RJ-45:

Power is provided on a CAT 5e cable to EZIM HD-SDI Card.

RS-232 IN on RJ-45:

RS-232 Input from ProductionVIEW HD-SDI, Precision Camera Controller, or a third-party controller.
Daisy Chain control is not supported.

RS-232 OUT on RJ-45:

The RS-232 Output from the CCU is connected to the RS-232 Input on the HD-18 camera.

Tally on 2-pin Phoenix type connector:

Contact Closure lights LED on front panel allowing indication of which QCCU/camera combination is
active in a multi-camera/CCU installation. A tally command will also be sent to the camera to illuminate
the LED on the camera.

G/L Input on BNC-F:

This option is not supported on the HD-18 camera.

Camera Feature Switches:

The CCU interface has an 8-position dip switch on the rear panel to allow certain functionality as it relates
to other Vaddio products and for future use.

Y-Gain:

The Y-Gain adjustment is not supported with the EZIM HD-SDI Slot Card system.

Distance:

The Distance Adjustment is not supported with the EZIM HD-SDI Slot Card system.

Video Outputs:

The video outputs on the back of the Quick-Connect CCU are not supported or used with the HD-SDI
Slot Card system. The SDI signal is fed on a coax cable directly from the back of the EZIM HD-SDI slot
card at the camera to the HD-SDI Console or monitor or over HD-SDI signal destination.

Video RJ-45

The EZCamera Power/Video RJ-45 port is not supported with the CCU/HD-SDI system.

WallVIEW CCU HD-18 HD-SDI Manual 341-988 Rev. A Page 6 of 26

WallVIEW CCU HD-18 HD-SDI

The Components (continued)

• EZIM HD-SDI Slot Card

Using only the most advanced and leading edge components available today, the EZIM HD-SDI produces
remarkable picture quality and is capable of 3Gb/s single link HD-SDI. Currently, the EZIM HD-SDI
coupled with the HD-18 PTZ camera can output 1080p/60, has been tested and is compatible with the
single link 3Gb/s inputs of the Vaddio ProductionVIEW HD-SDI Seamless Video Switcher and Camera
Controller.

Anatomy of the Vaddio EZIM HD-SDI Slot Card:

1) Two (2) HD-SDI/SDI Outputs on BNC

a. Carrier Class, Gold Finish Body and Contacts, Circuit Board Edge Mount (3Gb/s compliant)

2) One (1) RJ-45 Jack 36VDC used to Power HD-18 Camera and Card with the Quick-Connect CCU

3) Two (2) Captive, Spring Loaded, Retractable Thumb Screws

Figure 6:

EZIM HD-SDI Slot
Card - Front View

①③②

4) 24-Pin Self Guiding Blind Mating Interface Connector

5) Power Module (Regulator) provides power to Camera and Slot Card

6) 3Gb/s HD-SDI/SDI transmitter, generating a SMPTE 424M, SMPTE 292M, SMPTE 259M-C

compliant serial digital output signal with integrated low noise VCO and integrated cable driver .

Figure 7:

EZIM HD-SDI Slot Card - Top View

⑤

④

⑥

WallVIEW CCU HD-18 HD-SDI Manual 341-988 Rev. A Page 7 of 26

WallVIEW CCU HD-18 HD-SDI

First Time Set-up with the WallVIEW CCU HD-18 HD-SDI:

WallVIEW CCU HD-18 HD-SDI was designed to be exceptionally easy to use and operate. There is
documentation at the back of the manual for pin-outs for all of the connectors on the WallVIEW CCU HD-

ON

DIP SWITCH SETTINGS

IMAGE

IR

9600

OUT
OFF

ON

3

3

21

bps

38400

bps

4

4

NTSC

SD 4:3

SD

6 & 7 UP

SD

SD

SQ

PAL

5

68109

56

SD
LB

7

7

FLIP

BARS

OFF

ON ON

8

TEST

10

OFF

OFF

ON

910

0
1
2
3
4
5
6
7

HD VIDEO SELECT

720p/59.94

1080i/59.94

1080p/59.94

1080p/60

720p/50

1080i/50

1080p/50

480i/29.97

8
9

A
B
C
D
E
F

576i/25

1080p/30
1080p/25

18 HD-SDI System.

Getting Started:

First, set up the HD/SD-SDI output resolution for the camera, baud rate and image flip.

Figure 8: Dip Switch and Video Output Resolution Setting Options Label for the HD-18 Camera

IR 1

1 & 2 UP

IR 2ONIR 3

12

• IR 1, 2 & 3: These settings, using switches 1 & 2, determine the IR frequency of the IR remote control
that was supplied with your camera. The IR remote has the capability of operating up to three different
PTZ cameras from one remote, using the selector buttons at the top of the remote.

• IR Out: The IR output is sent on the RJ-45, RS-232 jack on the back of the camera. NOTE: When
using the Quick-Connect CCU, the IR output must be in the Off position (up).

• Baud Rate: The options for baud rate are either 9600 or 38,400 for RS-232.

• SD Output Frequency: Select either NTSC or PAL as the output for the camera’s SD signal that is

transmitted on the BNC connector.

• SD Output Size: Three options are available for the SD output, select from crop, squeeze or letterbox.
NOTE: These switches adjust only the composite SD output, not the SDI output, which will remain 4:3.

• Image Flip: Turning Image Flip on (switch down), will allow the camera to be inverted.

• Test Bars: Turning this switch on will override the camera video output and send test video bars from

the camera to the CCU to allow more accurate setting of the video level at the CCU.

• Switch 10: This switch is unused, and should be left in the OFF position.

RS-232 Cabling

For RS-232, use a standard CAT 5e cable (568B termination for RJ-45 connectors) from the RS-232 port
on the back of a Vaddio ProductionVIEW camera controller or switcher. If the camera will be connected
to a third-party control system (such as AMX or Crestron), a DB-9 to RJ-45 adapter cable is supplied with
the camera for RS-232.

IR OUT – Switch 3

When operating the HD-18 camera with the Quick-Connect CCU, the IR Output must be set to the OFF
position on the back of the camera. If it is not turned off, it will interfere with proper operation of the PTZ

camera.

INSTALLATION

The WallVIEW CCU HD-18 HD-SDI product was specifically designed for installation on a vertical wall
surface with Coax and CAT 5e cable connectivity for Video, Power and Control signaling (one coax and
two CAT 5e cables). Installation is simplified in that no custom cables and no power outlets are required
near the camera bracket. The use of “pass-thru” RJ-45 connectors should not be used (see notice on
page 2).

WallVIEW CCU HD-18 HD-SDI Manual 341-988 Rev. A Page 8 of 26

WallVIEW CCU HD-18 HD-SDI

Before Installing

• Locate the camera mounting location paying close attention to camera viewing angles, lighting

conditions, possible line of site obstructions, and checking for in-wall obstructions where the camera
is to be mounted. Pick a mounting location to optimize the performance of the camera.

• Pre-wire all cabling as required (see the wiring diagram example below).

• The Thin Profile Wall Mount for the HD-18 can be mounted directly to a 2-gang wall box or can be

mounted to the drywall using four dry wall anchors.

MOUNTING AND INSTALLATION INSTRUCTIONS
Step 1:

After determining the optimum location of the camera system, route the 1 (one) coax and 2 (two) CAT 5e
cables from the camera to the equipment head-end. The cables should feed-through the oval slot located
on the rear flange of the wall mount. If the bracket is to be mounted on a 2-gang wall box, use the screws
supplied with the wall box cover plate to attach the Thin Profile Wall Mount. If mounting to the drywall
with wall anchors, use the four (4) quality wall anchors. The mounting holes are slotted and are 90°
opposing to provide easy leveling. Level the mount and tighten down the mounting screws.

Step 2:
Installing the EZIM HD-SDI Slot Card:

• Remove all power connections

and be

certain that the HD-18 camera is not
powered up before attempting to install
the EZIM HD-SDI Slot Card. Remove
the blank plate (1) that covers the card
slot opening. Retain the blank panel as

Figure 9:

Rear View of
HD-18 with
Blank Plate
Shown

needed in case the Slot Card is ever
removed.

Please disconnect camera from power
before inserting or removing the EZIM
HD-SDI Slot Card.

• Carefully slide the EZIM HD-SDI Slot
Card into the HD-18 Camera base and
let the self mating connectors (2)
engage. The camera base is notched
on either side of the card slot (3) to aid
in alignment. Push the Slot Card in
completely.

Figure 10:

Rear View of HD-18
Showing Insertion of
the Slot Card

①

③

②

WallVIEW CCU HD-18 HD-SDI Manual 341-988 Rev. A Page 9 of 26

WallVIEW CCU HD-18 HD-SDI

• When the Slot Card is fully seated,
tighten the retractable spring loaded
captive screws (4). Do not force or cross

Figure 11:

Rear View of HD-18 with EZIM HD-SDI Slot Card Installed

tread the captive screws. Slowly tighten
both of the screws at the same time to
avoid any undesirable and/or dastardly
threading incidents.

Note:

The video outputs on the camera body (DE-15 with
YPbPr, BNC with CVBS and EZCamera VIDEO with
YPbPr) remain live and allow for simultaneous output
along with the HD-SDI Outputs.

FIRMWARE VERSIONS:
The firmware version V01.02.01 for the HD-18 camera that enables the HD-SDI Slot Card
to operate properly (dated May 20

th

, 2010). If you have purchased an HD-18 PTZ camera

④

before this date, a firmware update is required. The updates and directions are on the
Vaddio website (vaddio.com) and if assistance with the download and update is
needed, please contact Vaddio Technical Support at 800-572-2011.

Note: IR Output – Switch 3

When operating the HD-18 camera with the Quick-Connect CCU, the IR Output (switch 3) must be set to

the OFF position on the back of the camera. If it is not turned off, it will interfere with proper operation of

the PTZ camera.

Step 3:

Follow the sample configuration wiring diagrams in the manual for connecting the CAT 5e cables to the
camera and Quick-Connect CCU, using a Vaddio ProductionVIEW HD-SDI. Additional diagrams are
available on our website for installation with other equipment.

IMPORTANT NOTES:

• Check all CAT 5e cables for continuity in advance of the final connection.

Plugging the POWER CAT 5e Cable into the wrong RJ-45 may cause
damage to the camera system and void the warranty.

• Please do not use the “pass-thru” RJ-45 type connector. Please use

standard RJ-45 connectors for best results.

Step 4:

Place the camera onto the camera mount and using the ¼”-20 screws to secure the camera to the mount.

Step 5:

Connect the Vaddio 36 VDC power supply to an AC outlet. Power will travel down the Power CAT 5e
cable to the camera. The camera will “Home” to a centered position ready for control information from the
IR remote control or RS-232 camera controller of the integrators’ choice. To insure proper continuity of
control and operation of the cameras, the RS-232 controller (control system or joystick) should be
powered on after the camera.

Step 6:

For setting up the CCU, first make sure that the video monitor that you are using is set up correctly, and is
delivering accurate color reproduction. Next, adjust the iris level of the camera, so that brighter areas are
not washed out. After that is done, adjust the Pedestal level so that the black levels are not too dark, and
not too light. After this, adjust the Red & Blue Gain, Gamma, Detail, Knee and Chroma. NOTE: Gain
(next to Iris, should be left at 0 (zero), unless lighting is inadequate, then turn it to a level where the signal
brightness is at an appropriate level. Gain adds additional noise (grain) to the video the higher it is turned
up.

WallVIEW CCU HD-18 HD-SDI Manual 341-988 Rev. A Page 10 of 26

WallVIEW CCU HD-18 HD-SDI

Slot Card Dimensions:

Figure 12:

4.75”

(120.65mm)

3.0”

(76.2mm)

4.25”

(107.95mm)

5.875”

(149.23mm)

HD-SDI/SDI Cable Distances

Using the ProductionVIEW HD-SDI Console and the HD-18 HD-SDI Slot Card, expected HD-SDI/SDI
cable distances are approximately:

Resolutions: SMPTE STD Cable Distances*

720p SMPTE 292M Max. Length: 754.543 ft. (230m)
1080i

SMPTE 292M Max. Length: 754.543 ft. (230m)

1080p/29.97/25 Hz
1080p** SMPTE 424M Max. Length: 459.287 ft. (140m)

1080p/60/59.94/50Hz - 3Gb/s compliant
480i SMPTE 259M Max. Length: 820.179 ft. (250m)
576i SMPTE 259M Max. Length: 820.179 ft. (250m)

*Distances are approximate and based on using Belden 1694A coax cable. Results may vary according
to the quality of cable used and with the ability of individual installer/integrator.

**Tested with HD-SDI Receivers in the ProductionVIEW HD-SDI Consol e.

WallVIEW CCU HD-18 HD-SDI Manual 341-988 Rev. A Page 11 of 26

WallVIEW CCU HD-18 HD-SDI

EZIM HD-SDI Slot Card Output Resolutions:

The HD-SDI/SDI output of the Slot Card will be dependent on the output signal being fed into the slot card
from the Vaddio HD-18 camera. The HD Video Resolutions are selected via the 16-position rotary switch
on the HD-18 camera. A label has been placed on the bottom of the camera for reference. The HD-SDI
and the YPbPr are concurrent outputs at the same resolution. For example, when the rotary switch is set
to the “0” position, both the HD-SDI and the YPbPr output will be 720p/59.94.

Position Resolution SMPTE Std. Position Resolution SMPTE Std.

0 720p/59.94 SMPTE 292M 8 576i/25* SMPTE 259M
1 1080i/59.94 SMPTE 292M 9 NA

2 1080p/59.94** SMPTE 424M A NA
3 1080p/60** SMPTE 424M B NA
4 720p/50 SMPTE 292M C NA
5 1080i/50 SMPTE 292M D NA
6 1080p/50** SMPTE 424M E 1080p/30 SMPTE 292M
7 480i/29.97* SMPTE 259M F 1080p/25 SMPTE 292M

Rotary Switch on

Rear of HD-18

Camera

*A firmware upgrade to the HD-18 may be required to enable standard definition SDI outputs.
**Tested with HD-SDI Receivers in the ProductionVIEW HD-SDI Console. Compatibility with other 3Gb/s

Switchers and monitors may differ***.
***Certain equipment may not be capable of all the resolutions listed and therefore may not function

properly. If a certain resolution does not seem to work appropriately, please make sure that the
displaying device is properly configured, capable of the resolution that is chosen and is cabled correctly.
Furthermore, just because a resolution is listed on the above table, in this manual, does not mean the
display device can reproduce it accurately. There are many variables and not all monitors are created
equal. If you can’t get a certain resolution to display correctly, simply choose a different resolution.

Alternatively, if a resolution on this table is not listed, the camera and Slot Card will not output that
resolution. Please select a resolution on the table that the HD-18 Camera and HD-SDI Slot Card,
mixer/switcher/scaler/controller (i.e. ProductionVIEW HD-SDI), monitor and cable are all capable of
producing.

EZIM HD-SDI Slot Card Pin-Out Assignments for the POWER RJ-45 Jack

(This power jack to be used with the Quick-Connect CCU)

Power Connector RJ-45

Signal

Pin

1) Power +

2) Power -

3) Power +

4) Power -

5) Power +

6) Power -

7) Power +

8) Power -

12345678

WallVIEW CCU HD-18 HD-SDI Manual 341-988 Rev. A Page 12 of 26

WallVIEW CCU HD-18 HD-SDI

System Configuration Example 1:

Sample configuration of a WallVIEW CCU HD-18 connected to ProductionVIEW™ HD-SDI, with power, video, control
and tally cabling.

HD-SDI
Coax Cable

Power
CAT 5

Vaddio HD-18 with optional
HD-SDI Card in camera

*Quick-Connect CCU provides Power and
Color Correction/Shading to the HD-18

RS-232 & Tally
CAT 5

Cat. 5 up to 500’ (152.4m)

*Vaddio Quick-Connect CCU HD-18

720p/1080i up
to 230m using
Belden 1694A
coax cable

RS-232
Control

TALLY IN

TALLY OUT

HD-SDI

Camera Controller and Seamless 6X2 HD-SDI/SDI Switcher

Vaddio ProductionVIEW HD-SDI

Optional Accessory – UXHD CrossPoint (999-5690-000)

The Vaddio UXHD CrossPoint is a dual input (HD­SDI/SDI & analog component YPbPr or RGBHV or
SD), dual output (HD-SDI/SDI & analog
component YPbPr or RGBHV or SD) scaler and
format converter. The CrossPoint allows signal
conversion for delivering video into and out of
ProductionVIEW HD-SDI. See the next page for a
line drawing with UXHD CrossPoint.

WallVIEW CCU HD-18 HD-SDI Manual 341-988 Rev. A Page 13 of 26

WallVIEW CCU HD-18 HD-SDI

System Configuration Example 2:

HD-SDI System using two HD-18 Cameras with the HD-SDI Slot Cards installed. The HD-18’s are
powered and color-corrected by the Quick-Connect CCU and controlled by the ProductionVIEW HD-SDI
Seamless Switcher/Controller. In this case a PC is connected to a UXHD CrossPoint to convert the
RGBHV format to HD-SDI and at the same time, the UXHD CrossPoint can convert one of the two HD­SDI Program Outputs to use with an existing RGBHV or HD video projector.

HD-SDI (Coax)

Vaddio HD-18 Cameras

With optional HD-SDI Slot Card

Power

RS-232

HD-SDI (Coax)
720p/1080i up to
230m using Belden
1694A coax cable

ProductionVIEW HD-SDI

HD-SDI PROGRAM
Monitor*

Power & Control
Cat. 5 Cables up
to 500’ (152.4m)

HD-SDI CAM 2 IN

HD-SDI CAM 1 IN

Power

RS-232

RS-232

RS-232

(Conv. to HD-SDI)

*Simulated Video Feeds

HD-SDI
(PC)

PC IN

PC

RGBHV

Vaddio UXHD

IN

HD-SDI
PROG
OUT

HD-SDI

HD-SDI
PROG OUT

HD-SDI PREVIEW

Monitor*

CrossPoint

OUT

RGBHV

(HD-SDI

PROG)

RGBHV

Projector

WallVIEW CCU HD-18 HD-SDI Manual 341-988 Rev. A Page 14 of 26

WallVIEW CCU HD-18 HD-SDI

Other Configurations:

Simple Configuration - Local 12 VDC Power, Control from ProductionVIEW HD-SDI and HD-SDI Video
from the Slot Card to ProductionVIEW HD-SDI.

Local PowerRite™
12 VDC Power
(outlet at camera)

Vaddio HD-18 Cameras*

With optional EZIM HD-SDI Slot Card

Local PowerRite
12 VDC Power
(outlet at camera)

HD-SDI
COAX

HD-SDI
COAX

RS-232

CAT 5

RS-232

CAT 5

ProductionVIEW
HD-SDI Console*

HD-SDI PROGRAM

(Feed to Satellite Truck)

HD-SDI

*Up to six (6) Vaddio HD-18 PTZ Cameras can be controlled by the ProductionVIEW HD-SDI Seamless
Video Switcher and Joystick Camera Control Console.

HD-SDI

**HD -SDI Monitor

PROGRAM

**Simulated Video Feeds

HD-SDI

**HD -SDI Monitor

PREVIEW

WallVIEW CCU HD-18 HD-SDI Manual 341-988 Rev. A Page 15 of 26

WallVIEW CCU HD-18 HD-SDI

General Specifications:

WallVIEW CCU HD-18 HD-SDI

Part Numbers WallVIEW CCU HD-18 HD-SDI 999-6908-000 - North America

• Vaddio ClearVIEW HD-18 *

Image Device 1/3” CCD
Picture Elements 1.3 Megapixels
HD-SDI Signals

SDI Signals
Lens 18x Optical Zoom
Focal Length f=4.7 to 84.6mm
Horizontal Viewing Angle 3.2 to 55.2 degrees (16:9)
Video S/N Ratio >50 dB
Invertible Yes, with image flip control
Minimum Illumination 1.8 Lux
Control Protocol VISCA
Serial Communication RS-232 (9600 or 38,400)
Pan Range +170 degrees to -170 degrees
Tilt Range +90 degrees to -30 degrees
Pan/Tilt Speed 0.25° to 60° degrees/second
Preset Positions 16 (internal), 6 recalled via IR Remote
Weight 5.8 lbs. (2.63 kg.)

• Quick-Connect CCU Interface *

Connectors Power Connector: 5.5mm OD x 2.5mm ID

Camera Select Switch For Future Use – All switches should be in the down position
Video Adjustments Detail, Red and Blue Gain, White Balance (Auto/Manual), Iris (Auto/Manual) Pedestal, Knee,

CAT 5e Cable Distance Up to 500’ (152.4m) – Control and Power Only
SDI Distance See page 4 of manual for distances
Power Supply 36 VDC, 2.78 Amp
Dimensions 1-RU Rack Mount - 1.75” H x 19” W x 6” D (4.45 cm x 4.26 cm x 15.24 cm)

• Thin Profile Wall Mount HD-18 *

Materials 12-Gauge CRS with Black Powder Coat Paint
Dimensions 5.125” H x 6.75” W x 10” D (13 cm x 17.15 cm x 25.4 cm)
Weight Approx. 2.4 lbs. (1.1kg)

HD-SDI Slot Card for HD-18 Camera *

Part Number 998-6900-007 - For use with the Vaddio HD-18 PTZ Camera Only
Power Jack:

HD-SDI Output:
Slot Card Connection to

Camera
HD-SDI Transmitter

Dimensions:
Weight: 0.3lbs (.13607772375643 kg - roughly)

* All Products Designed and Manufactured in the USA

WallVIEW CCU HD-18 HD-SDI 999-6908-000W - North America (Arctic White Version)
WallVIEW CCU HD-18 HD-SDI 999-6908-001 - International
WallVIEW CCU HD-18 HD-SDI 999-6908-001W - International (Arctic White Version)

HD: 1080p @ 60/50/30/25 Hz, 1080i @ 59.94/50 Hz, 720p @ 59.94/50Hz
SD: 480i/29.97 or 576i/25 SD-SDI

Power RJ-45: Supplies 36V to EZIM HD-SDI
Control In RJ-45: Accepts RS-232 from ProductionVIEW or other non-daisy-chain control systems
Control Out RJ-45: RS-232 output to camera
Tally: 2-Pin Phoenix type spring cage connector
G/L Input: BNC Connector for Sync (not available on HD-18)
Video Outputs: Unused
Video RJ-45: Unused

Chroma and Gamma, with 3 scenes of storage

One (1) RJ-45, 36VDC used to Power HD-18 Camera and Slot Card with the Quick-Connect CCU
over Cat. 5
Two (2) Outputs on BNC Connectors (Carrier Class, Gold Finish Body and Contacts, Circuit Board
Edge Mount - 3Gb/s compliant)
One (1) 24-pin Self Guiding Blind Mating Interface Connector
Two (2) Captive, Spring Loaded, Retractable Thumb Screws
3Gb/s HD-SDI/SDI transmitter, generating a SMPTE 424M, SMPTE 292M, SMPTE 259M-C

compliant serial digital output signal with integrated low noise VCO and integrated cable driver
(polarizing imaging array not included)

PCB: 4.75” (120.65mm) W x 3.0” (76.2mm) D x .063” (1.6002mm )Thick
With Connectors and Mounting Plate: 5.875” (149.23mm) W x 4.25” (107.95) D

WallVIEW CCU HD-18 HD-SDI Manual 341-988 Rev. A Page 16 of 26

WallVIEW CCU HD-18 HD-SDI

Compliance and CE Declaration of Conformity - Vaddio HD-18 PTZ Camera

FCC Part 15 Compliance

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his/her own expense.

Operation is subject to the following two conditions: (1) This device may not cause interference, and (2)
This device must accept any interference including interference that may cause undesired operation of
the device.

Changes or modifications not expressly approved by Vaddio can affect emission compliance and could
void the user’s authority to operate this equipment.

ICES-003 Compliance

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus
set out in the Radio Interference Regulations of the Canadian Department of Communications.
Le présent appareil numérique n’emet pas de bruits radioélectriques dépassant les limites applicables
aux appareils numeriques de la classe A préscrites dans le Règlement sur le brouillage radioélectrique
édicte par le ministère des Communications du Canada.

European Compliance

This product has been evaluated for Electromagnetic Compatibility under the EMC Directive for Emissions and
Immunity and meets the requirements for a Class A digital device. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate measures.

Standard(s) To Which Conformity Is Declared:
EMC Directive 2004/108/EC

EN 55022 A: 2006 + A1 2007 (CISPR 22:2005/A1:2005) Conducted and Radiated Emissions

 AS/NZS CISPR 22: 2006, Australia and New Zealand - Conducted and Radiated Emissions
 VCCI V-3/2009.04, Japan - Conducted and Radiated Emissions

EN 55024: 1998 + Amendments A1: 2001 + A2: 2003 - Electromagnetic Compatibility - Immunity
EN 61000-4-2 Electrostatic Discharge
EN 61000-4-3 Radiated Immunity
EN 61000-4-4 Electrical Fast Transients
EN 61000-4-5 Surge Immunity
EN 61000-4-6 Conducted Immunity
EN 61000-4-8 Power Frequency Magnetic Field
EN 61000-4-11 Voltage Dips, Interrupts and Fluctuations

WallVIEW CCU HD-18 HD-SDI Manual 341-988 Rev. A Page 17 of 26

WallVIEW CCU HD-18 HD-SDI

Compliance and CE Declaration of Conformity - Vaddio EZIM HD-SDI Slot Card

FCC Part 15 Compliance

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to Part 15, Subpart B, of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his/her own expense.

Operation is subject to the following two conditions: (1) This device may not cause interference, and (2)
This device must accept any interference including interference that may cause undesired operation of
the device.

Changes or modifications not expressly approved by Vaddio can affect emission compliance and could
void the user’s authority to operate this equipment.

ICES-003, Issue 4: 2004, Compliance

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus
set out in the Radio Interference Regulations of the Canadian Department of Communications.
Le présent appareil numérique n’emet pas de bruits radioélectriques dépassant les limites applicables
aux appareils numeriques de la classe A préscrites dans le Règlement sur le brouillage radioélectrique
édicte par le ministère des Communications du Canada.

European Compliance

This product has been evaluated for Electromagnetic Compatibility under the EMC Directive for Emissions and
Immunity and meets the requirements for a Class A digital device. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate measures.

Standard(s) To Which Conformity Is Declared:
EMC Directive 2004/108/EC

EN 55022 A: 2006 + A1 2007 (CISPR 22:2005/A1:2005) Conducted and Radiated Emissions

 AS/NZS CISPR 22: 2006, Australia and New Zealand - Conducted and Radiated Emissions
 VCCI V-3/2009.04, Japan - Conducted and Radiated Emissions

EN 55024: 1998 + Amendments A1: 2001 + A2: 2003 - Electromagnetic Compatibility - Immunity
EN 61000-4-2: 1995 + Amendments A1: 1998 + A2: 2001 - Electrostatic Discharge
EN 61000-4-3: 2006 - Radiated Immunity
EN 61000-4-4: 2004 + Corrigendum 2006 - Electrical Fast Transients
EN 61000-4-5: 2006 - Surge Immunity
EN 61000-4-6: 2007 - Conducted Immunity
EN 61000-4-8: 1993 + Amendment A1: 2001 - Power Frequency Magnetic Field
EN 61000-4-11 Second Edition: 2004 - Voltage Dips, Interrupts and Fluctuations

WallVIEW CCU HD-18 HD-SDI Manual 341-988 Rev. A Page 18 of 26

WallVIEW CCU HD-18 HD-SDI

Compliance and CE Declaration of Conformity - Vaddio Quick-Connect CCU

FCC Part 15 Compliance

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his/her own expense.

Operation is subject to the following two conditions: (1) This device may not cause interference, and (2)
This device must accept any interference including interference that may cause undesired operation of
the device.

Changes or modifications not expressly approved by Vaddio can affect emission compliance and could
void the user’s authority to operate this equipment.

ICES-003 Compliance

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus
set out in the Radio Interference Regulations of the Canadian Department of Communications.
Le présent appareil numérique n’emet pas de bruits radioélectriques dépassant les limites applicables
aux appareils numeriques de la classe A préscrites dans le Règlement sur le brouillage radioélectrique
édicte par le ministère des Communications du Canada.

European Compliance

This product has been evaluated for Electromagnetic Compatibility under the EMC Directive for
Emissions and Immunity and meets the requirements for a Class A digital device. In a domestic
environment this product may cause radio interference in which case the user may be required to take
adequate measures.

Standard(s) To Which Conformity Is Declared:
EMC Directive 89/336/EEC
EN 55022A Conducted and Radiated Emissions
EN 55024 Electromagnetic Compatibility - Immunity
EN 61000-4-2 Electrostatic Discharge Requirements
EN 61000-4-3 Radiated Electromagnetic Field Requirement
EN 61000-4-4 Electrical Fast Transients / Burst Requirements
EN 61000-4-5 Surge Requirements
EN 61000-4-6 Conducted Immunity Requirements
EN 61000-4-8 Power Frequency Magnetic Field Requirements
EN 61000-4-11 Voltage Dips, Interrupts and Fluctuations Requirements

WallVIEW CCU HD-18 HD-SDI Manual 341-988 Rev. A Page 19 of 26

WallVIEW CCU HD-18 HD-SDI

Warranty Information:

Hardware* Warranty - One year limited warranty on all parts. Vaddio warrants this product against

defects in materials and workmanship for a period of one year from the day of purchase from Vaddio. If
Vaddio receives notice of such defects during the warranty period, they will, at their option, repair or
replace products that prove to be defective.

Exclusions - The above warranty shall not apply to defects resulting from: improper or inadequate
maintenance by the customer, customer applied software or interfacing, unauthorized modifications or
misuse, operation outside the normal environmental specifications for the product, use of the incorrect
power supply, improper extension of the power supply cable or improper site operation and maintenance.

Vaddio Customer service – Vaddio will test, repair, or replace the product or products without charge if
the unit is under warranty and is found to be defective. If the product is out of warranty, Vaddio will test
then repair the product or products. The cost of parts and labor charge will be estimated by a technician
and confirmed by the customer prior to repair. All components must be returned for testing as a complete
unit. Vaddio will not accept responsibility for shipment after it has left the premises.

Vaddio Technical support - Vaddio technicians will determine and discuss with the customer the criteria
for repair costs and/or replacement. Vaddio Technical Support can be contacted through one of the
following resources: e-mail support at [e-mail] or online at www.va ddio.com

Return Material Authorization (RMA) number - Before returning a product for repair or replacement,
request an RMA from Vaddio’s technical support. Provide a technician with a return phone number, e­mail address, shipping address, and product serial numbers and describe the reason for repairs or
returns as well as the date of purchase and proof of purchase. Include your assigned RMA number in all
correspondence with Vaddio. Write your assigned RMA number on the outside of the box when returning
the product.

Voided warranty – The warranty does not apply if the original serial number has been removed or if the
product has been disassembled or damaged through misuse, accident, modifications, or unauthorized
repair. Cutting the power supply cable on the secondary side (low voltage side) to extend the power to
the device (camera or controller) voids the warranty for that device.

Shipping and handling - Vaddio will not pay for inbound shipping transportation or insurance charges or
accept any responsibility for laws and ordinances from inbound transit. Vaddio will pay for outbound
shipping, transportation, and insurance charges for all items under warranty but will not assume
responsibility for loss and/or damage by the outbound freight carrier.

• If the return shipment appears damaged, retain the original boxes and packing material for inspection by
the carrier. Contact your carrier immediately.

Products not under warranty - Payment arrangements are required before outbound shipment for all
out of warranty products.

*Vaddio manufactures its hardware products from parts and components that are new or equivalent to new in accordance with
industry standard practices.

.

WallVIEW CCU HD-18 HD-SDI Manual 341-988 Rev. A Page 20 of 26

WallVIEW CCU HD-18 HD-SDI

Other General Information:
Care and Cleaning

• Do not attempt to take any of these products apart at any time. There are no user-serviceable
components inside.

• Do not spill liquids or liquid type substances onto the HD-SDI Slot Card, the CCU or in the HD-18
Camera.

• Keep this device away from food or liquid or other immeasurably bad sticky or oily things.

• For smears or smudges on the products, wipe with a clean, soft cloth but do not attempt to clean the

exposed parts, ICs or connectors on the HD-SDI Slot Card.

• Do not use any abrasive chemicals at any time on any product.

Operating and Storage Conditions:

Do not store or operate the HD-SDI Slot Card under the following conditions:

• Temperatures above 40°C (104°F) or temperatures below 0°C (32°F)

• High humidity, condensing or wet environments or if left out in the lawn overnight

• In inclement weather, especially when it is bad

• Dusty and explosive environments with more than a pile of dust in the air

• Dry environments with an excess of static discharge

• Under severe vibration

Restatement of Important Safeguards:

Read and understand all instructions before using. Do not operate any device if it has been dropped o r
damaged. In this case, a Vaddio technician must examine the product before operating. To reduce the
risk of electric shock, do not immerse in water or other liquids and avoid extremely humid conditions.

Use only the approved power supplies provided with the system.
Use of any unauthorized power supply will void any and all warranties.

Do not use RJ-45 “pass-thru” connectors - they are gnarly and bad,
and should never be used on important, permanent installations.
Use standard RJ-45 connectors for best and consistent results.

Do not insert or remove the EZIM HD-SDI Slot Card into an HD-18
Camera when the camera is powered ON. Detach all power
connectors before installing or removing the HD-SDI Slot Card. The
EZIM HD-SDI Slot Card is not hot swappable.

FIRMWARE VERSIONS:

The firmware version V01.02.01 for the HD-18 camera that enabl es the HD-SDI Slo t
Card to operate properly (dated May 20
PTZ camera before this date, a firmware update is required. The updates and
directions are on the Vaddio website (vaddio.com) and if assistance with the
download and update is needed, please contact Vaddio T echnical Support at 800­572-2011.

th

, 2010). If you have purchased an HD-18

WallVIEW CCU HD-18 HD-SDI Manual 341-988 Rev. A Page 21 of 26

WallVIEW CCU HD-18 HD-SDI

Appendix 1:

Video Pin-out Table for WallVIEW HD-18

Pin YPbPr

1 Pr
2 Y
3 Pb
4 ­5 ­6 Pr GND
7 Y GND
8 Pb GND

9 ­10 ­11 ­12 ­13 ­14 ­15 -

NOTE: This output, on the back of the camera is still
active, even with the EZIM HD-SDI slot card installed.

Appendix 2: Camera Dimensions

WallVIEW CCU HD-18 HD-SDI Manual 341-988 Rev. A Page 22 of 26

WallVIEW CCU HD-18 HD-SDI

Appendix 3: Communication Specification

Communication Speed: 9600 bps (default)
Start bit: 1
Stop bit: 1
Data bits: 8
Parity: None
No Flow control

NOTE: The Vaddio ClearVIEW HD-18 Control Protocol is similar, but not identical to the Sony™
VISCA™ command set in order to be compatible with several popular control devices. Not all VISCA
commands are supported and there are many HD-18 specific commands in the following Command and
Inquiry Lists.

12345678

Pin # RJ-45 RS-232 and IR Out Pins

1) Unused

2) Unused

3) I R Out (TTL level) (not used in CCU Config)

4) IR Output (not used in CCU Config)

5) I R Ground (not used in CCU Config)

6) GND

7) RXD (from TXD of control source)

8) TXD (to RXD of control source)

HD-18 Command List (1/2)

Command Set V Command Command Packet Comments

AddressSet Y Broadcast 88 30 01 FF Address Set
IF_Clear Y Broadcast 88 01 00 01 FF I/F Clear
CommandCancel Y 81 2p FF p: Socket No(=1 to2)
CAM_Power Y

CAM_Zoom Y

CAM_Focus Y

CAM_WB Y

CAM_RGain Y

CAM_BGain Y

CAM_AE Y

CAM_Iris Y

CAM_Gain Y

On

Y

Off
Stop

Tele(Standard)

Y

Wide(Standard)

Y

Tele(Variable)

Y

Wide(Variable)

Y

Direct

Y

Direct(Variable)

Y

Stop
Far(Standard)

Y

Near(Standard)

Y

Far(Variable)

Y

Near(Variable)

Y

AutoFocus

Y

ManualFocus

Y

Auto/Manual

Y

Auto

Y

Manual
Reset

Up

Y

Down

Y

Direct

Y

Reset
Up

Y

Down

Y

Direct

Y

Full Auto

Y

Manual
Shutter Priority

Y

Iris Priority

Y

Bright

Y

Reset
Up

Y

Down

Y

Direct

Y

Reset
Up

Y

Down

Y

Direct

Y

81 01 04 00 02 FF
81 01 04 00 03 FF

81 01 04 07 00 FF
81 01 04 07 02 FF
81 01 04 07 03 FF
81 01 04 07 2p FF
81 01 04 07 3p FF
81 01 04 47 0p 0q 0r 0s FF
81 01 7E 01 4A 0V 0p 0q 0r 0s FF

81 01 04 08 00 FF
81 01 04 08 02 FF
81 01 04 08 03 FF
81 01 04 08 2p FF
81 01 04 08 3p FF
81 01 04 38 02 FF
81 01 04 38 03 FF
81 01 04 38 10 FF

81 01 04 35 00 FF
81 01 04 35 05 FF

81 01 04 03 00 FF
81 01 04 03 02 FF
81 01 04 03 03 FF
81 01 04 43 00 0p 0q 0r FF

8x 01 04 04 00 FF
8x 01 04 04 02 FF
81 01 04 04 03 FF
81 01 04 44 00 0p 0q 0r FF

81 01 04 39 00 FF
81 01 04 39 03 FF
81 01 04 39 0A FF
81 01 04 39 0B FF
81 01 04 39 0D FF

81 01 04 0B 00 FF
81 01 04 0B 02 FF
81 01 04 0B 03 FF
81 01 04 4B 00 00 0p 0q FF

81 01 04 0C 00 FF
81 01 04 0C 02 FF
81 01 04 0C 03 FF
81 01 04 4C 00 00 0p 0q FF

Power On/Off

p:0(Slow) to 7(Fast)
p:0(Slow) to 7(Fast)
pqrs: Zoom Position*
V:(Speed) 0-7

Supported as ‘Standard’
Supported as ‘Standard’

pqr:000-1ff

pqr:000-1ff
Auto Exposure Mode

Manual Control Mode
Shutter Priority Mode
Exposure Priority Mode (default)
AGC Priority Mode

pq(0x00-0x11)

pq(0x00-0x1E)

WallVIEW CCU HD-18 HD-SDI Manual 341-988 Rev. A Page 23 of 26

WallVIEW CCU HD-18 HD-SDI

HD-18 Command List (2/2)

Command Set V Command Command Packet Comments

CAM_Backlight Y Y On

CAM_Aperture Y

CAM_Memory Y

CAM_IDWrite Y 81 01 04 22 0p 0q 0r 0s FF pqrs:Camera ID(==0000 – FFFF)
IR_Receive Y

IR_ReceiveReturn N+

Pan-tiltDrive Y

Tally Y

Preset Pan Speed Y Pan/Tilt Speed 81 01 7E 01 0B WW VV ZZ FF WW: Pan Speed (0x01-0x18)

Motor Config Y Y Hard Motor Stops

BLK.Enhance Y Pedestal 81 01 7E 53 00 00 0p 0q FF pq: Black Level (0x01-0xFD)
GMA.Enhance Y Gamma 81 01 7E 54 00 00 0p 0q FF pq: Gamma (0x00-0x8F)
CRM.Enhance Y Chroma 81 01 7E 55 00 00 0p 0q FF pq: Chroma (0x08-0x1F)
KNE.Enhance Y Knee 81 01 7E 55 00 00 0p 0q FF pq: Knee (0x0-07F)
CAM_Shutter Y

CAM_ExpComp Y

CAM_ICR
Cut Filter

Off
Reset

Up

Y

Down

Y

Direct

Y

Reset

Y

Set

Y

Recall

On
Off

Y

On/Off

Y

On

N+

Off
Up

Down

Y

Left

Y

Right

Y

UpLeft

Y

UpRight

Y

DownLeft

Y

DownRight

Y

Stop

Y

Absolute Position

Y

Y

Home

Reset
Y
Y

On
Y

Off

Soft Motor Stops

Reset

Up

Y

Down

Y

Direct

Y

On

Off

Y

Reset

Y

Up

Y

Down

Y

Direct

Y
Y Y ICR On

ICR Off

81 01 04 33 02 FF
81 01 04 33 03 FF

81 01 04 02 00 FF
81 01 04 02 02 FF
81 01 04 02 03 FF
81 01 04 42 00 00 0p 0q FF

81 01 04 3F 00 0p FF
81 01 04 3F 01 0p FF
81 01 04 3F 02 0p FF

81 01 06 08 02 FF
81 01 06 08 03 FF
81 01 06 08 10 FF

81 01 7D 01 03 00 00 FF
81 01 7D 01 13 00 00 FF

81 01 06 01 VV WW 03 01 FF
81 01 06 01 VV WW 03 02 FF
81 01 06 01 VV WW 01 03 FF
81 01 06 01 VV WW 02 03 FF
81 01 06 01 VV WW 01 01 FF
81 01 06 01 VV WW 02 01 FF
81 01 06 01 VV WW 01 02 FF
81 01 06 01 VV WW 02 02 FF
81 01 06 01 VV WW 03 03 FF
81 01 06 02 VV WW
0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z FF
0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z FF

81 01 06 04 FF
81 01 06 05 FF

81 01 7E 01 0A 00 02 FF
81 01 7E 01 0A 00 03 FF

81 01 7E 01 70 00 00 FF
81 01 7E 01 70 00 01 FF

81 01 04 0A 00 FF
81 01 04 0A 02 FF
81 01 04 0A 03 FF
81 01 04 4A 00 00 0p 0q FF

81 01 04 3E 02 FF
81 01 04 3E 03 FF
81 01 04 0E 00 FF
81 01 04 0E02 FF
81 01 04 0E 03 FF
81 01 04 4E 00 00 0p 0q FF

81 01 04 01 02 FF
81 01 04 01 03 FF

pq(0x00-0x3F)
p:Memory No(=0-0xf)

WW: Pan Speed (0x01-0x18)
VV:Tilt Speed(0x01-0x14)

YYYY: Pan Position*
ZZZZ: Tilt Position*

VV:Tilt Speed(0x01-0x14)
ZZ:Zoom Speed(0-7);

(Only supported in Shutter
Priority Mode)

Pq: 0x00-0x0E
AutoExposure Off

AutoExpouse On

Pq: 0x00-0x1E
ICR On

ICR Off

Additional Information:

Pan Range: 8044 – 7FBC (-32,700 to +32,700)
Tilt Range: E891 – 4C2B (-5,999 to +19,499)

* Actual Pan/Tilt ranges defined in Inquiry list

WallVIEW CCU HD-18 HD-SDI Manual 341-988 Rev. A Page 24 of 26

WallVIEW CCU HD-18 HD-SDI

HD-18 Inquiry List (1/1)

Inquiry Command V Command Command Packet Comments

CAM_PowerInq Y

CAM_ZoomPosInq Y 81 09 04 47 FF y0 50 0p 0q 0r 0s FF pqr: Zoom Position
CAM_WBModeInq Y 81 09 04 35 FF y0 50 00 FF

CAM_RGain Y 81 09 04 43 FF y0 50 00 0p 0q 0r FF pqr:000-1ff
CAM_BGain Y 81 09 04 44 FF y0 50 00 0p 0q 0r FF pqr:000-1ff
CAM_AEModeInq Y 81 09 04 39 FF y0 50 00 FF

CAM_Iris Y 81 09 04 4B FF y0 50 00 00 0p 0q FF pq(0x00-0x11)
CAM_Gain Y 81 09 04 4C FF y0 50 00 00 0p 0q FF pq(0x00-0x1E)
CAM_BacklightModeInq Y 81 09 04 33 FF y0 50 02 FF

CAM_ApertureInq Y 81 09 04 42 FF y0 50 00 00 0p 0q FF pq(0x00-0x3F)
CAM_MemoryInq Y 81 09 04 3F FF y0 50 0p FF p:Memory No(=0-0xf)
CAM_IDInq Y 81 09 04 3F FF y0 50 0p 0q 0r 0s FF pqrs:(0000 – FFFF)
CAM_ReceiveInq Y 81 09 06 08 FF y0 50 02 FF

Pan-TiltMaxSpeedInq Y 81 09 06 11 FF y0 50 WW VV FF WW: Pan Speed (0x01-0x18)

Pan-tiltPositionInq Y 81 09 06 12 FF y0 50 0Y 0Y 0Y 0Y 0Z 0Z

TallyInq Y

PresetSpeedInq Y 81 09 7E 01 0B FF y0 50 WW VV ZZ FF WW: Pan Speed (0x01-0x18)

Motor Config Y 81 09 7E 01 70 FF y0 50 00 FF

BLK.Enhance Y 81 01 7E 53 FF y0 50 00 00 0p 0q FF pq: Black Level (0x01-0xFD)
GMA.Enhance Y 81 01 7E 54 FF y0 50 00 00 0p 0q FF pq: Gamma (0x00-0x8F)
CRM.Enhance Y 81 01 7E 55 FF y0 50 00 00 0p 0q FF pq: Chroma (0x08-0x1F)
KNE.Enhance Y 81 01 7E 56 FF y0 50 00 00 0p 0q FF pq: Knee (0x0-07F)
CAM_AEModeInq Y 81 09 04 39 FF y0 50 00 FF

CAM_ShutterPosInq Y 81 09 04 4A FF y0 50 00 00 0p 0q FF pq: ShutterPosition

CAM_ExpCompModeInq Y 81 09 04 3E FF y0 50 02 FF

CAM_ExpCompPosInq Y 81 09 04 4E FF y0 50 00 00 0p 0q FF pq: ExpComp Pos -Iris Position
CAM_ICRModeInq Y 81 09 04 01 FF y0 50 02 FF

81 09 04 00 FF

81 09 7E 01 0A FF y0 50 02 FF

Y

y0 50 02 FF
y0 50 03 FF

y0 50 05 FF

y0 50 03 FF

y0 50 03 FF

y0 50 03 FF

0Z 0Z FF

y0 50 03 FF

y0 50 01 FF

y0 50 03 FF
y0 50 0A FF
y0 50 0B FF
y0 50 0D FF

y0 50 03 FF

y0 50 03 FF

On
Off(Standby)

Auto
Manual

Auto Exposure Mode
Manual Control Mode

On
Off

On
Off

VV:Tilt Speed(0x01-0x14)
YYYY: Pan (0x0100-0x1800)

ZZZZ:Tilt (0x0100-0x1400)
On

Off

VV:Tilt Speed(0x01-0x14)
ZZ:Zoom Speed(0-7);

Hard Motor Stops
Soft Motor Stops

Auto Exposure Mode
Manual Control Mode
Shutter Priority Mode
Exposure Priority Mode
AGC Priority Mode

(Only supported in Shutter
Priority Mode)

On - AE Mode Off
Off – AE Mode On

ICR On
ICR Off

WallVIEW CCU HD-18 HD-SDI Manual 341-988 Rev. A Page 25 of 26

WallVIEW CCU HD-18 HD-SDI

Toll Free: 800-572-2011 ▪ Phone: [phone] ▪ FAX: [phone]

9433 Science Center Drive, Minneapolis, MN 55428

www.vaddio.com

©2010 Vaddio - All Rights Reserved. Reproduction in whole or in part without written permission is prohibited. Specifications and pricing are
subject to change without notice. Vaddio, ClearVIEW, ProductionVIEW, Quick-Connect, UXHD, WallVIEW, EZCamera, EZIM and PowerRite
are registered trademarks of Vaddio. All other trademarks are property of their respective owners. Document Number 341-988 Rev. A

WallVIEW CCU HD-18 HD-SDI Manual 341-988 Rev. A Page 26 of 26