Vaddio WallVIEW 70 User Manual

Installation and User Guide

y

Camera and Electronic Products for Integrators

WallVIEW™ PTZ Systems

WallVIEW 50i PTZ, WallVIEW 100 PTZ and WallVIEW 70 PTZ
Pan/Tilt/Zoom Camera Systems

Figure 1: WallVIEW Systems (left to right); WallVIEW 50i PTZ, WallVIEW 100 PTZ, WallVIEW 70 PTZ, with each camera showing

INTRODUCTION

The Vaddio WallVIEW PTZ Camera Systems are complete wall-mounted camera
packages featuring the Vaddio EZCamera™ Cabling System that allows the installer to
use Category 5 cabling to run power, video and camera control. The included
PowerRite™ power supply provides the right amount of power required for proper
operation of the camera over Cat. 5 cabling.

INTENDED USE

EZCamera Cabling Shoe and Thin Profile wall mount bracket.

Before installing the Vaddio WallVIEW PTZ Camera Systems, please read
the entire manual thoroughly. All Vaddio camera systems were designed
for use indoors. Outdoor operation is not recommended, hasn’t been
tested, and could damage the camera and/or create a potentially unsafe
operating condition. Use only the Vaddio PowerRite power supply
provided.

SAVE THESE
INSTRUCTIONS

IMPORTANT
SAFEGUARDS

The information contained in this manual will help you install the Vaddio
WallVIEW systems. For reference, Vaddio keeps copies of Specifications,
Installation and User Guides and most pertinent product drawings for the
Vaddio product line on the website. These documents can be downloaded
from www.vaddio.com

Read and understand all instructions before using. Do not operate any
electrical device if it has been dropped or damaged. In this case, a Vaddio
technician must examine the product before operating. To reduce the risk
of electric shock, do not immerse in water or other liquids and avoid
extremely humid conditions.

free of charge.

Use only the power supply provided with the Vaddio WallVIEW products.
Use of an

unauthorized power supply will void any and all warranties.

Ⓒ2006 Vaddio - All Rights Reserved. Reproduction in whole or in part without written permission is prohibited. Specifications and pricing are
subject to change without notice. Vaddio, WallVIEW, ControlVIEW, EZCamera, Quick-Connect and PowerRite are registered trademarks of

Vaddio. All other trademarks are property of their respective owners. Document Number 010-2201-000 Rev. F

Page 1 of 8

UNPACKING

Carefully remove all of the parts from the packaging. Unpack and identify the
following parts for each of the WallVIEW systems:

WallVIEW 100 PTZ

Part Numbers: 999-2204-000 (NTSC) and 999-2204-001 (PAL)

• One (1) Sony® EVI-D100 Camera (not included in WallVIEW Kit)

• Vaddio IR Remote Commander for Sony Cameras (not included in Kit version)

• One (1) Vaddio EZCamera Cable Shoe for D100 camera

• One (1) Thin Profile wall mount bracket (matching color)

• One (1) 12’ (3.66m) S-Video cable

• One (1) 12’ (3.66m) Composite video cable (RCA connectors)

• One (1) Vaddio Quick-Connect™ Box

• One (1) EZCamera Control Adapter

• One (1) 15VDC PowerRite power supply with power cable

• Mounting hardware & Documentation

WallVIEW 70 PTZ

Part Numbers: 999-2704-000 (NTSC) and 999-2704-001 (PAL)

• One (1) Sony EVI-D70 Camera (not included in WallVIEW Kit)

• Vaddio IR Remote Commander for Sony Cameras (not included in Kit version)

• One (1) Vaddio EZCamera Cable Shoe for D70 camera

• One (1) Thin Profile wall mount bracket (matching color)

• One (1) 12’ (3.66m) S-Video cable

• One (1) 12’ (3.66m) Composite video cable (RCA connectors)

• One (1) Vaddio Quick-Connect™ Box

• One (1) EZCamera Control Adapter

• One (1) 18VDC PowerRite power supply with power cable

• Mounting hardware & Documentation

WallVIEW 50i PTZ

Part Numbers: 999-4204-000 (NTSC) and 999-4204-001 (PAL)

• One (1) Canon® VC-C50i Camera with Canon IR Remote

• One (1) Vaddio EZCamera Cable Shoe for 50i Camera

• One (1) Thin Profile wall mount bracket

• One (1) 12’ (3.66m) S-Video cable

• One (1) 12’ (3.66m) Composite video cable (RCA connectors)

• One (1) Vaddio Quick-Connect™ Box

• One (1) EZCamera Control Adapter

• One (1) 18VDC PowerRite power supply with power cable

• Mounting hardware & Documentation

Important Note:

The table below provides minimum and maximum CAT-5 cable distances that can be
used with the standard and optional power supplies with each camera s yst em. 24
VDC power supplies are available as an accessory (Part # 451-2000-024).

For PAL camera versions, both EURO and UK Power cables are included.

For PAL camera versions, both EURO and UK Power cables are included.

For PAL camera versions, both EURO and UK Power cables are included.

WallVIEW 100

WallVIEW 70

WallVIEW 50

18 VDC Power Supply

(included)

Up to 115 ft.

(35.1m)

Up to 200 ft.

(61m)

Up to 185 ft.

(56.4m)

24 VDC Power Supply

(sold separately)

115 ft. to 250 ft.

(35.1m to 76.2m)

200 ft. to 300 ft.

(61m to 91.4m)

185 ft. to 275 ft.

(56.4m to 83.8m)

Vaddio WallVIEW – Document Number – 010-2201-000 Rev. F

Page 2 of 8

INSTALLATION

Before

Installing

Wiring

Diagram

Examples

Daisy Chain

Control

Configuration

The WallVIEW products are cameras specifically designed for installation on a
vertical wall surface with Cat. 5 cable connectivity for Power, Video and Control
signaling. Installation is simplified in that no custom 8-Pin mini-din cables or
expensive S-Video plenum cables are needed and no power outlets are required
near the camera bracket. All cabling is routed to the head-end using Cat. 5 cabling
with the EZCamera Cabling system.

• Locate the camera mounting location paying close attention to camera viewing
angles, lighting conditions, possible line of site obstructions, and checking for
in-wall obstructions where the camera is to be mounted. Pick a mounting
location to optimize the performance of the camera.

• Pre-wire all cabling as required (see wiring diagram examples).

• The WallVIEW 100, 70 and 50i can be mounted to standard 2-gang wall

boxes. All cameras are basically lightweight and the thin profile wall mount
bracket can be adequately secured to the wall with the four (4) provided
conical plastic wall anchors (or your choice of dry wall anchor).

The Basic Idea: WallVIEW 50i, 70 & 100 PTZ

ProductionVIEW

Super Joystick

RS-232

Cat. 5

Cat. 5

S-Video or
Composite

Power to Camera
Video From Camera

Quick-Connect Box

WallVIEW 100 PTZ
with Camera, Shoe
and Mount

Display, Projector
or Codec

Figure 2:

The WallVIEW 50i, 70 & 100 uses a single cat. 5 for Power and Video and a 2nd Cat. 5 for control.
Control is wired in a daisy chain configuration if a single control port is to be used.

Power Supply

RS-232
OUT

Figure 3:

Vaddio ControlVIEW™ Xtreme Camera
Controller with Single RS-232 Control Port
controlling 3 WallVIEW 100s in Daisy Chain
Configuration

RS-232
IN

RS-232
OUT

RS-232
IN

RS-232
OUT

RS-232
IN

Note:

TXD, RXD & GND are required for basic control. For Daisy Chaining, DSR and DTR are required for
Sony products (Pins 1 and 2 on the Cat. 5 cable) and CTS and RTS are Required for Canon products
(Pins 3 and 4 on the Cat. 5 cable).

Vaddio WallVIEW – Document Number – 010-2201-000 Rev. F

Page 3 of 8