VADDIO WallVIEW, 999-6994-000, 999-6994-001 Installation And User Manual

Download

Installation and User Guide

WallVIEW™ HD-USB SR System

Featuring the ClearVIEW™ HD-USB PTZ Camera, CONCEAL™ Mount, Active USB Extension Cable and Power Extension Module

Part Numbers: 999-6994-000 - North America 999-6994-001 - International

WallVIEW HD-USB SR Camera System

Table of Contents

Overview: ................................................................................................................................................................................................................ 3

Soft Ware Notes ................................................................................................................................................................................................. 3

Unpacking ............................................................................................................................................................................................................... 4

ClearVIEW HD-USB PTZ Conferencing Camera ............................................................................................................................................... 5

Diagram: Rear View Connectors with Feature Call-outs: ............................................................................................................................. 5

Diagram: Front View with Feature Call-outs: ................................................................................................................................................ 6

Connecting the Extension Devices to the Camera ................................................................................................................................................. 7

Diagram: Basic Connectivity Example: ......................................................................................................................................................... 7

Detail .................................................................................................................................................................................................................. 8

Diagram: Connection Detail with the Power Extension Module and the Active USB 2.0 Extension Cable .................................................. 8

Diagram: Connection Detail with Local Power to the Camera and the Active USB 2.0 Extension Cable ..................................................... 8

Reference Diagrams ............................................................................................................................................................................................... 9

Reference Diagram: Basic Connectivity Example ........................................................................................................................................ 9

Reference Diagram: Connectivity Example 2 with Audio: ............................................................................................................................. 9

Reference Diagram: H.264 Streaming Connectivity (for Release 2.0 when IP Streaming is enabled): ...................................................... 10

Reference Diagram: Connection Diagram Example using A CDN (for release 2.0 when IP is enabled): .................................................. 10

First Time Set-up with the ClearVIEW HD-USB PTZ Camera .............................................................................................................................. 11

Getting Started ................................................................................................................................................................................................. 11

Table: Switch Setting Label on Bottom of the HD-USB Camera: ............................................................................................................... 11

The Settings Rotary Encoder ........................................................................................................................................................................... 12

For the 1

Step by Step Instructions to install the WallVIEW HD-USB SR Camera System ................................................................................................. 13

Compatibility .......................................................................................................................................................................................................... 14

Internal Web Pages and Control ...................................................................................................................................................................... 15

DHCP Set-up (Dynamic Host Configuration Protocol) ..................................................................................................................................... 15

Static IP Set-up ................................................................................................................................................................................................. 15

Screen Shot Tour .................................................................................................................................................................................................. 16

Admin Pages .................................................................................................................................................................................................... 17

Connecting the Camera to the Program of Choice: .............................................................................................................................................. 21

Skype Example ................................................................................................................................................................................................. 21

VLC Media Player Example .............................................................................................................................................................................. 21

Technical Specifications: ....................................................................................................................................................................................... 22

Compliance and CE Declaration of Conformity: ClearVIEW HD-USB PTZ Camera ........................................................................................... 23

Warranty Information: ............................................................................................................................................................................................ 24

Appendix 1: Communication Specification ........................................................................................................................................................... 25

A Final Note about Software Releases: ................................................................................................................................................................ 26

Release of the Camera and Software, only the USB 2.0 Streaming Video is Active ...................................................................... 12

WallVIEW HD-USB SR PTZ Camera System Document Number 342-0465 Rev. A 6 Page 2 of 28

WallVIEW HD-USB SR Camera System

VERVIEW

Based on the remarkable Vaddio ClearVIEW HD-USB PTZ Conferencing Camera, the WallVIEW HD-USB SR (short range) System includes many of the features that you would expect out of a WallVIEW branded product. The ClearVIEW HD-USB is the world’s first broadcast-quality HD PTZ camera with USB 2.0 output, Ethernet streaming and analog component (YPbPr) outputs built right into the camera. Simply plug the HD-USB camera directly into your PC and there is no need for a separate capture device. The ClearVIEW HD-USB uses standard USB 2.0 UVC drivers, which means that no special USB drivers require installation or can provide headaches. As a result the HD-USB camera works seamlessly with any software application running on any OS that supports USB 2.0 devices. All this, and the ClearVIEW HD-USB PTZ cameras are made in the USA too.

The ClearVIEW HD-USB combines impressive performance with an equally impressive feature set. Using the UVC standard drivers for USB 2.0 video, the HD-USB camera is a plug and play PTZ camera for Unified Communications soft client conferencing systems such as Skype®, Jabber® and Lync®,

WallVIEW HD-USB SR System with CONCEAL Mount

which offers a vast improvement over the “inexpensive webcam” systems available today.

The HD-USB is a high definition conferencing camera suitable for the small, medium or even the largest conferencing space available. The HD zoom lens allows HD-USB to capture a wide angle of view (58.1°) to view everyone at a conference room table, as well as capture an individual from a long distance (3.2°) in a larger room. The motorized zoom lens offers 19X optical zoom and is built around a 1/3-Type Sony® Exmor, progressive scan, high-speed, low noise CMOS image sensor with a total of 1.3 Megapixels for precise and vibrant HD color video images. The HD-USB achieves improved picture quality even in low light environments requiring a minimum illumination rated at an amazingly low 0.7 LUX (F1.6 - 50IRE).

Soft Ware Notes

: Like the ClearVIEW HD-USB PTZ Camera, the WallVIEW systems will be released with two (2) major software releases. Release 1.0 will allow USB 2.0 streaming and with the following Release 2.0 software, the ClearVIEW HD-USB will also support H.264 video streaming. It has a built in Ethernet network interface for both IP control and IP Streaming can be initiated directly from the camera. It will support either RTSP or HLS streaming protocols. The software is easily upgradeable in the field over the Ethernet port.

The WallVIEW HD-USB SR system includes the HD-USB camera, the CONCEAL camera mount, an active, portpowered 20m (65.6168’) USB-2.0 extension cable, the Vaddio Power Extension Module for extending power over CAT-5 cable to the camera and all the USB 2.0 cables, power supplies and mounting hardware that are required to install the WallVIEW HD-USB SR system.

Important Safeguards:

Read and understand all instructions before using. Do not operate any device if it has been dropped or damaged. In this case, a Vaddio technician must examine the product before operating. To reduce the risk of electric shock, do not immerse in water or other liquids and avoid extremely humid conditions.

Use only the power supply provided with the system. Use of any unauthorized

power supply will void any and all warranties.

Please do not use “pass-thru” type RJ-45 connectors. These pass-thru type connectors do not work well for professional installations and can be the cause of in termittent connections which can result in the RS-232 control line failing and locking up, and/or compromising the HSDS™ signals. For best results please use standard RJ-45 connectors and test all cables for prope r pinouts

rior to use and connection to Vaddio product.

WallVIEW HD-USB SR PTZ Camera System Document Number 342-0465 Rev. A 6 Page 3 of 28

WallVIEW HD-USB SR Camera System

Intended Use:

Before operating the device, please read the entire manual thoroughly. The system was designed, built and tested for use indoors, and with the provided power supply and cabling. The use of a power supply other than the one provided or outdoor operation has not been tested and could damage the device and/or create a potentially unsafe operating condition.

Save These Instructions:

The information contained in this manual will help you install and operate your product. If these instructions are misplaced, Vaddio keeps copies of Specifications, Installation and User Guides and most pertinent product drawings for the Vaddio product line on the Vaddio website. These documents can be downloaded from

www.vaddio.com free of charge.

NPACKING

North American Version 999-6994-000

Carefully remove the device and all of the parts from the packaging. Unpack and identify the following parts:

 One (1) ClearVIEW HD-USB PTZ Camera (998-6990-000)  One (1) Vaddio IR Remote Commander  One (1) EZCamera™ Control Adapter (RJ-45 to DB-9)  One (1) Vaddio PowerRite™ 12 VDC, 3.0 Amp Power Supply  One (1) AC Cord Set for North America  One (1) 10’ (3.05m) USB 2.0 Type A (Male) to USB B (Male) Cable  One (1) 1’ (305mm) USB 2.0 Type A (Male) to USB B (Male) Cable  One (1) 20m (65’) Active, Port Powered USB 2.0 Extension Cable  One (1) Power Extension Module  One (1) 24 VDC, 2.75 Amp PowerRite™ Switching Power Supply  One (1) AC Cord Set for North America  One (1) CONCEAL Mount and Hardware for the HD-USB Camera  Documentation

International Version 999-6994-001

Carefully remove the device and all of the parts from the packaging. Unpack and identify the following parts:

 One (1) ClearVIEW HD-USB PTZ Camera (998-6990-000)  One (1) Vaddio IR Remote Commander  One (1) EZCamera™ Control Adapter (RJ-45 to DB-9)  One (1) Vaddio PowerRite™ 12 VDC, 3.0 Amp Power Supply  One (1) Euro Power Cord  One (1) UK Power Cord  One (1) 10’ (3.05m) USB 2.0 Type A (Male) to USB B (Male) Cable  One (1) 1’ (305mm) USB 2.0 Type A (Male) to USB B (Male) Cable  One (1) 20m (65’) Active, Port Powered USB 2.0 Extension Cable  One (1) Power Extension Module  One (1) 24 VDC, 2.75 Amp PowerRite™ Switching Power Supply  One (1) Euro Power Cord  One (1) UK Power Cord  One (1) CONCEAL Mount and Hardware for the HD-USB Camera  Documentation

WallVIEW HD-USB SR PTZ Camera System Document Number 342-0465 Rev. A 6 Page 4 of 28

WallVIEW HD-USB SR Camera System

ClearVIEW HD-USB PTZ Conferencing Camera

Diagram: Rear View Connectors with Feature Call-outs:

Connectors and Functions:

1) 12 VDC Input: Power input on EIAJ-04 connector for local power.

2) HD Video Select: A rotary switch that allows the user to choose the component HD output video resolution

3) Camera Settings (Dip Switch Settings): Settings for IR remote frequency, baud rate, SD output format, and

4) RS-232 IN & IR Out: The upper RS-232 Port is not implemented on the HD-USB Camera. Use the RS-232

5) YPbPr Output: Component HD video is fed through the DE-15 connector (HD-15 for the shell sized

WallVIEW HD-USB SR PTZ Camera System Document Number 342-0465 Rev. A 6 Page 5 of 28

④

⑤

③

⑥

②

Note: Use the EZ POWER VIDEO port with the Power Extension Module

①

⑧

and format. For the USB output, use rotary switch settings 0, 1, 4, or 5. Please see the sections on available resolutions and concurrent resolutions when using USB 2.0 and analog component outputs

image flip, test bars can be configured on these switches.

Port on the lower card ONLY.

challenged). YPbPr and Composite signals are simultaneous. Note: This is an HD camera and the SD signals are down converted and are really not the sweet spot of this camera. This is a courtesy feature only.

⑨

⑩ ⑫

⑪

⑬

⑦

WallVIEW HD-USB SR Camera System

Connectors and Functions (continued)

6) Composite Video (CVBS) Output: The CVBS output feeds out SD video signals and is configurable with

the dip switches to choose between 480i/NTSC or 576i/PAL in 4:3 formats. Squeeze and letterbox modes are also available (see dip switches).

7) EZ POWER VIDEO Port: Use the RJ-45 EZ POWER VIDEO port with the Power Extension Module. The

Power Extension Module sends DC power over pins 1 & 2 to power the HD-USB camera for up to 150’ (45.72m). In the Case of the WallVIEW HD-USB SR system, the limitation is the USB 2.0 Extension Cable, which extends USB 2.0 only 65’ (20m).

8) 5 VDC Output: The 5 VDC output is on an EIAJ-03 connector was added to supply power to the active

Extreme USB Extender transmitter side. The receiver side is powered by the computer’s USB port or powered USB Hub.

9) USB 2.0 Connector: The USB 2.0 is on a type-B Female and attaches to a PC running a soft-client video

conferencing system or video capture software that uses UVC (USB Video Class) standard drivers. No other drivers are required to plug the HD-USB into a computer and have it work. The UVC drivers will auto negotiate the top resolution that the PC and HD-USB Camera can accomplish together and auto implement it, and bob’s your uncle.

10) Settings Rotary Encoder: The Settings encoder allows the user to easily access automatically negotiated

USB or H.264 Preset and User configurations without having to plug in a computer to configure it. While a computer is recommended for set-up, this rotary allows for a quick set-up.

11) Ethernet 10/100 Port (H.264 Streaming Active with Software Release 2.0): The network port has green

and yellow LEDs that indicate ready and usage states. The port allows for access to the internal web pages for camera set-up and control. The network port will stream (unicast) H.264/MPEG4/AVC video (from CIF up to and including 1080p/30) starting with Release 2.0 of the Software.

12) RS-232 Port: The RS-232 Port allows external control systems to engage a rudimentary API. Basic

functions include pan, tilt zoom, on/off etc. The functions on the Vaddio IR Remote Commander are mirrored in the API. Most control is expected to come from the internal web page via Ethernet, Telnet or over USB

2.0.

13) Permanent USB Resource Slot Card: The lower row of connectors and the brains of the HD-USB Came ra

are located on this permanent slot card. The card is not removable and is not compatible with any other Vaddio camera. Please do not try to remove this card at any time.

ClearVIEW HD-USB PTZ Conferencing Camera

Diagram: Front View with Feature Call-outs:

1) Zoom Lens and Image Sensor: The 19X optical zoom lens is

built around a 1/3-Type, high-speed, progressive scan CMOS image sensor with a total of 1.3 Megapixels for precise HD video image acquisition.

2) Blue Power Light: A Vaddio blue power light is illuminated

when the camera is turned on.

3) IR Sensors: IR sensors are built into the front of the HD-USB to receive IR signals from the IR remote

control supplied with the camera.

4) Red Tally Light: The red tally light is not used with the HD-USB

Camera

WallVIEW HD-USB SR PTZ Camera System Document Number 342-0465 Rev. A 6 Page 6 of 28

➊

➍

➋

➌

WallVIEW HD-USB SR Camera System

ONNECTING THE EXTENSION DEVICES TO THE CAMERA

The following diagrams pertain to the connectivity of the WallVIEW HD-USB SR Camera System with the CONCEAL Mount, Power Extension Module and 20m (65.6’) Active USB Extension Cable

Diagram: Basic Connectivity Example:

WallVIEW HD-USB with

CONCEAL Mount

To EZ POWER VIDEO RJ-45 Port

USB 2.0 Distance Limit with the Active

Extension Cable = 20m (65.6’)

CAT-5 Cable - 24 VDC Power

(Pin 1: +, Pin 2: -)

24 VDC, 2.75A

Power Supply

Power Extension

Module

USB 2.0

Cable

Male

M - F

Active USB

2.0 Extension

Type-A Male

USB 2.0 Video using

USB Video Class

(UVC) Drivers

Cable

to Type-A

Female

Host PC with Conferencing Application

1’ (305mm)

Type-B Male

to Type-A

Diagram: Basic Connectivity Example:

This example uses the HD-USB PTZ Camera and Vaddio’s EasyUSB Mixer/Amp, two (2) Echo Cancelling EasyMic™ MicPODs, Power Extension Module, Active USB 2.0 Extension Cable and Two (2) Bose Ceiling Speakers to create a complete room system.

WallVIEW HD-USB with

CONCEAL Mount

PC Video Monitor - HD

Large Screen Format

Bose FS-16F Ceiling Speakers

Optimize for Voice

To EZ POWER

VIDEO RJ-45 Port

Distance Limit

20m (65.6’)

1’ (305mm)

USB 2.0

Cable

Type-B Male

to Type-A

Male

65.6’ Active USB 2.0

Extension Cable

* Type-A Male to Type-A Female

USB 2.0 Video using

USB Video Class

(UVC) Drivers

PC HD

Video

USB 2.0 Cable

USB 2.0 Audio using

USB Audio Class

(UAC) Drivers

Host Tower PC with UC Application

8 Ohm

Speaker

Cable

EasyUSB

Mixer/AMP

Cat-5e

Cable

Cat-5e

Cable

CAT-5 Cable - 24 VDC Power

(Pin 1: +, Pin 2: -)

Power Extension

Module

24 VDC, 2.75A

Power Supply

WallVIEW HD-USB SR PTZ Camera System Document Number 342-0465 Rev. A 6 Page 7 of 28

Two (2) EasyMic MicPODs with

three (3) integrated mic elements

and three (3) Acoustic Echo

Cancellers per mic

8 Ohm

Speaker

Cable

WallVIEW HD-USB SR Camera System

Detail

Diagram: Connection Detail with the Power Extension Module and the Active USB 2.0 Extension Cable

The 24VDC connection from the Power Extension Module to the camera can provide adequate power up to 150’ (45.7m) away. The 65.6’ (20m) long USB extension cable limits the overall distance the camera and computer can be separated.

HD-USB PTZ Camera

Rear View

Power Extension

Module

1’ (305mm)

USB 2.0

Type-B Male

to Type-A

Cable

Male

65.6’ (20m) Active USB 2.0 Extension Cable Type-A Male to Type-A Female

CAT-5 Cable - 24 VDC Power

(Pin 1: +, Pin 2: -)

The 24VDC connection from the Power Extension Module will power the camera up to 150’ (45.7m) away.

DC Power

24 VDC, 2.75A

Power Supply

Modern Computer

Diagram: Connection Detail with Local Power to the Camera and the Active USB 2.0 Extension Cable

In this example the camera is powered by the provided 12 VDC, 3.0 Amp power supply.

Local Power

Provided

12 VDC Power

Supply

USB 2.0 Cable

1’ (305mm)

M F

PC Video Monitor - HD

Large Screen Format

PC HD

Video

65.6’ (20m) Active USB 2.0 Extension Cable Type-A Male to Type-A Female

Host Tower PC with UC Application

USB 2.0

WallVIEW HD-USB SR PTZ Camera System Document Number 342-0465 Rev. A 6 Page 8 of 28

WallVIEW HD-USB SR Camera System

EFERENCE DIAGRAMS

Reference Diagram: Basic Connectivity Example

HD-USB Camera and a Soft-client videoconferencing system (audio is not included in this example).

HD-USB

Conferencing

Camera

USB 2.0

Port

USB 2.0 using only

UVC Drivers

USB 2.0

Port

PC with Host Application

Reference Diagram: Connectivity Example 2 with Audio:

This example uses the HD-USB PTZ Camera and Vaddio’s EasyUSB™ Mixer/Amp, two (2) Echo Cancelling EasyMic™ MicPODs and Two (2) Bose Ceiling Speakers to create a complete room system using programs such as Skype®, Jabber®, Google+®, Microsoft Lync® and others. This configuration features driverless USB 2.0 Video and Acoustic Echo Cancelled (AEC) Audio.

PC Video Monitor - HD

Large Screen Format

Bose FS-16F Ceiling Speakers

Optimize for Voice

ClearVIEW HD-USB

Conferencing

Camera

USB 2.0 Cable

USB 2.0 Video using

USB Video Class

(UVC) Drivers

PC HD

Video

USB 2.0 Cable

USB 2.0 Audio using

USB Audio Class

(UAC) Drivers

8 Ohm

Speaker

Cable

EasyUSB™

Mixer/AMP

Cat-5e

Cable

8 Ohm

Speaker

Cable

Cat-5e

Cable

Tower PC with Host

Application

Two (2) EasyMic MicPODs with

three (3) integrated mic elements

and three (3) Acoustic Echo

Cancellers per mic

WallVIEW HD-USB SR PTZ Camera System Document Number 342-0465 Rev. A 6 Page 9 of 28

WallVIEW HD-USB SR Camera System

Reference Diagram: H.264 Streaming Connectivity (for Release 2.0 when IP Streaming is enabled):

The HD-USB Camera has a Unicast streaming output suitable for up to six (6) concurrent users (at lower resolutions). This configuration shows four (4) concurrent users.

H.264 STREAMING

VIDEO

Network

LAN/WAN

Internet

HD-USB PTZ CAMERA

Reference Diagram: Connection Diagram Example using A CDN (for release 2.0 when IP is enabled):

For a Large Number of Viewers - Use a CDN Content Distribution Network such as Wowza, Amazon or iCloud and more…

WallVIEW HD-USB SR PTZ Camera System Document Number 342-0465 Rev. A 6 Page 10 of 28

WallVIEW HD-USB SR Camera System

FIRST TIME SET-UP WITH THE CLEARVIEW HD-USB PTZ CAMERA

The ClearVIEW HD-USB PTZ Camera was designed to be exceptionally easy to use and operate. There is documentation at the back of the manual for pin-outs. These pin-outs are also available, along with application TechNotes, from the Vaddio website www.vaddio.com.

Getting Started

Step 1: Using the HD Video Select Rotary Switch and Camera Settings Dip Switch on the back of the camera,

set up the camera’s output resolution and functional preferences. There is a label on the bottom of the camera that identifies the choices.

HD-USB Rear Panel

Table: Switch Setting Label on Bottom of the HD-USB Camera:

IR 1

1 & 2 UP

IR 2ONIR 3

Step 2: For USB 2.0 proper operation, set the HD VIDEO SELECT switch to “0” (720p/59.94), “1” (1080i/59.94),

“4” (720p/50) or “5” on the HD-USB Camera. These are the only resolutions that the USB 2.0 and H.264 engines accept. From these four resolutions, all other USB 2.0 and H.264 resolutions are derived.

 For concurrent USB 2.0 and Analog Component (YPbPr), switch settings 0, 1, 4 and 5 are the four

resolutions that can be both digital (USB 2.0 or H.264) and Analog (YPbPr). These resolutions, 720p/59.94, 1080i/59.94, 720p/50 & 1080i/59.94 are the most used resolutions for HD video and are broadcast standards.

 For Analog (YPbPr) output only, all HD VIDEO SELECT switch settings will operate.  For Composite output on the BNC connector, this output is independent from the USB 2.0 resolutions and

the SD settings and are formatted by dip switches 5, 6 and 7.

Step 3: Choose the IR frequency (1, 2 or 3) on the camera for use with the IR Remote Commander. Since only one USB camera can be plugged into a PC at a time, recommended default is Freq. 1 (dip switches 1 & 2 up).

HD Video Select Switch

DIP SWITCH SETTINGS

IR OUT OFF

9600

bps

38400

bps

NTSC

PAL

Camera Settings 10-Pos Dip Switches

SD LB

IMAGE

FLIP

OFF

ON ON

SD 4:3

6 & 7 UP

SD SQ

68109

TEST

BARS

OFF

910

HD VIDEO AND USB 2.0 SELECT

720p/59.94 - USB

1080i/59.94 - USB

1080p/59.94

1080p/60

720p/50 - USB

1080i/50 - USB

1080p/50

480i/29.97

USE ROTARY SETTINGS 0, 1, 4 & 5 FOR USB 2.0 OUT

9 A B C D E F

576i/25

1080p/30 1080p/25

④

WallVIEW HD-USB SR PTZ Camera System Document Number 342-0465 Rev. A 6 Page 11 of 28

WallVIEW HD-USB SR Camera System

Step 4: Leave the IR out OFF (up) as default. Step 5: Use 9600bps for control speed as default.

 If the camera is mounted inverted, then set the Image Flip to ON, otherwise leave it off.  The test bars are really, really non-standard (horizontal - just to mess with the old-timers) and will override the

video output. These test bars are 75% IRE. Use the test bars for…testing.

The Settings Rotary Encoder

The settings encoder allows the user to easily access automatically negotiated USB or H.264 Preset and User configurations without having to plug in a computer to configure it. While a computer is recommended for set-up, this rotary allows for a quick set-up. In the first release of the camera, the USB 2.0 will be activated while the H.264 network streaming will not be activated until the 2 allow the user to quickly determine how the camera is going to be used and give access to presets (both hard and user configurable).

Software Release 2.0 adds H.264 over Ethernet to the HD-USB.

For the 1

The H.264 will follow in Release 2.0, so for now, put the Rotary Selection Switch on the USB Resource Card to position “0”. The label will be on every camera, so when Release 2.0 is ready and upgraded in the field, the label will be ready to go. The documentation will be updated with the extra pages to explain the H.264 set-up in a reliably competent manner.

Position “0” will give the camera the ability to auto-negotiate with the host PC and automatically decide the highest resolution (MJPEG video up to and including 720p/30) that the camera and computer can display and process within the computer’s software.

There will be a table on the profile page which reflects the data on the label above. For Release 2.0, this will be on a web page served up by the camera.

software release. On the bottom of the camera, another label will be included to

FUNCTIONS OF ROTARY SELECTION SWITCH ON USB RESOURCE CARD

SW. POS

0 1 2 3 4 5 6 7

ACTIVE

PORT

USB

ETHERNET ETHERNET ETHERNET ETHERNET ETHERNET ETHERNET ETHERNET

FORMAT PRESET #

USB 2.0

H.264 H.264 H.264 H.264 H.264 H.264 H.264

UVC Auto-Negotiated with Host

PRESET 2 PRESET 3 PRESET 4

USER 1 USER 2 USER 3

Res/FPS/

Bit Rate

720p/30/4Mb 720p/30/4Mb 480p/60/2Mb 480p/60/2Mb

STREAMING

PROTOCOL

RTSPPRESET 1

HLS(HTTP)

RTSP

HLS(HTTP)

SW.

POS

8 9 A B C D E F

ACTIVE

PORT

ETHERNET

FUTURE

WEB CTL.

FUTURE

RESET RESTORES TO FACTORY DEFAULTS FUTURE FUTURE FUTURE

Active Lines for Software Release 1.0 are shaded in yellow.

Release of the Camera and Software, only the USB 2.0 Streaming Video is Active

A Cautionary Note: In the event that the rotary switch was moved from “0” and left on “C” - RESET - RESTORES TO FACTORY DEFAULTS, and is power cycled, all data

will be lost. Sometimes a RESET is required, but those occasions are generally few and far between. On the web pages, a warning dialog box was added to inform the administrator the state of the switch. If the factory reset is not desired, please move the switch back to “0” and do not power cycle the camera. The warning looks almost exactly like the warning below…

FORMAT PRESET #

H.264 USER 4

DYMANIC CONTROL THOUGH WEB PAGE ONLY

Res/FPS/

Bit Rate

STREAMING PROTOCOL

WallVIEW HD-USB SR PTZ Camera System Document Number 342-0465 Rev. A 6 Page 12 of 28

WallVIEW HD-USB SR Camera System

TEP BY STEP INSTRUCTIONS TO INSTALL THE WALL

VIEW HD-USB SR C

AMERA SYSTEM

Step 1: Locating the Camera

Locate the camera mounting position while paying close attention to camera viewing angles, lighting conditions, possible line of site obstructions, and checking for in-wall obstructions where the camera is to be mounted. Pick a mounting location to optimize the performance of the camera.

Like all Vaddio WallVIEW systems, the WallVIEW HD-USB SR is easy to install and operate. The product was specifically designed with CAT-5 cable connectivity for the extension of power and an Active USB 2.0 Extension cable that is powered by the computer’s USB port.

Step 2:

After determining the optimum location of the camera system, run a CAT-5 cable and the Active USB 2.0 Extension Cable from the computer location to the camera location. Make sure to mark and test the CAT-5 cable and use real RJ-45 crimper and connectors using the 568B straight-through wiring standard. Please do not use the “feed-thru” type RJ-45 connectors for professional installations.

Step 3:

Using the CONCEAL wall mount directions, install the CONCEAL mount. If mounting to the drywall with wall anchors, use four (4) quality wall anchors. Make sure to level the mount and tighten the mounting screws.

Step 4:

Connect the CAT-5 cable to the EZ POWER VIDEO RJ-45 port on the back panel of the HD-USB camera. Connect 1’ (305mm) USB 2.0 Cable Type-B Male into the USB Type-B Female on the back panel of the HD-USB camera. Connect the Active USB Extension Cable’s Type-A Female to the 1’ (305mm) USB cable’s Type-A Male Connector. Field dress the cabling and tuck it back into the CONCEAL mount and place on the back cover to hide all the cabling.

NOTE: Check all CAT-5 cables for continuity in advance of the connection. Do not plug the CAT-5 cable into any other RJ-45 port but the EZ POWER VIDEO port. There is 24 VDC Volts on Pins 1 & 2. Plugging into any other port may cause damage to the camera system and void the warranty.

Step 5: At the Head-End

Plug the Active USB Extension Cable Type-A Male directly into the computer. Plug the other end of the CAT-5 cable into the RJ-45 port of the Power Extension Module.

Step 6: Last Chance to check the wiring

After double checking the wiring, plug the 24 VDC power supply into the Power Extension Module and plug the power supply into the power outlet. The HD-USB camera should home and also should be sending USB 2.0 MJPEG video to the computer.

Hint: It may be a good idea to set up the camera “on the ground” to ensure that it works properly and all the computer and camera settings are correct prior to installing it on the wall with the CONCEAL mount.

WallVIEW HD-USB

with CONCEAL Mount

WallVIEW HD-USB SR PTZ Camera System Document Number 342-0465 Rev. A 6 Page 13 of 28

WallVIEW HD-USB SR Camera System

COMPATIBILITY

The HD-USB PTZ Camera will work with the following web browsers, soft codecs, computer operating systems and media players. Thorough testing has been performed by the technical staff at Vaddio to ensure that the HD-USB camera is compatible with the elements listed below.

Compatibility - Web Browsers:

1) Internet Explorer (IE 8 and above)

2) Safari (Rev 4 and 5)

3) Safari/iOS (Rev 4 and 5)

4) Chrome (the latest and current release - auto updating)

5) FireFox (the latest and current release - auto updating)

Compatibility - Soft Codecs: HD-USB Camera shall be compatible with the following soft codecs: Release 1.0:

1) Skype

2) MS Lync

3) Jabber

4) Polycom M100

5) Vidyo Desktop

Future Releases:

1) Google+

2) Adobe Connect

3) ClearSea

4) Web Ex

5) Apple FaceTime

3.4.3: Compatibility - Operating Systems

1) Apple OS X (10.7 and above)

2) Windows XP w/Service Pack 3 with known issues and errata

3) Windows 7

4) Linux

3.4.1: Compatibility - Media Players:

The UVC with MJPEG video shall be compatible with the industry leading PC media players.

1) Quick-Time

2) Windows Media Player (playback)

3) VLC Media Player

Other Compatibilities:

As more UC soft-client and lecture capture programs are released and gain popularity, Vaddio will provide a continuing research and development effort to ensure the camera’s viability and compatibility with other manufacturer’s products.

WallVIEW HD-USB SR PTZ Camera System Document Number 342-0465 Rev. A 6 Page 14 of 28

WallVIEW HD-USB SR Camera System

Internal Web Pages and Control

The internal web pages will allow control of the HD-USB and allow the user to control the camera via an internet connection. These web pages will allow the user or administrator to set security passwords, change the IP address if not dynamic, view diagnostics, access the firmware upgrade page and more.

To access the HD-USB’s web pages, first include your Network Administrator for the network that the camera will be placed. Access to the internal web pages can be achieved three ways for set-up of the HD-USB’s IP address and other administrative functions.

DHCP Set-up (Dynamic Host Configuration Protocol)

DHCP Set-up (skip this section if Static IP). If the LAN has a DHCP (dynamic host configuration protocol) server, then the IP address, gateway and routing information will automatically be assigned. The HD-USB software is defaulted to DHCP. To find out the assigned IP address please have the network administrator provide the IP address and enter that into one of the approved browsers.

The HD-USB will attempt to dynamically obtain an IP address using DHCP, but it will fall back to the default address of 169.254.1.1 if no DHCP server can be found.

Static IP Set-up

It is highly recommended that the Network Administrator is involved on the Static IP set-up of the HD-USB camera…really.

The static IP can be assigned either through the network or directly to a computer using a cross-over cable. Depending on the age of the computer, you may not need a cross-over cable. Either way the steps are the same for network or direct connect to a computer.

The default address of the HD-USB camera is 169.254.1.1 and the Subnet mask is 255.255.0.0. Different computer OS types all have their way of doing things, but they are essentially doing the same thing, changing the IP address so the web pages of the HD-USB are accessible.

For Windows XP Pro, the routine to get to the network settings is fairly simple. Click on the Start button > Control Panels > Network Connections > Right Click Local Area Connection > click on Properties > click on Internet Protocol (TCP/IP) > click on Properties and IP Address and Subnet Mask numbers are displayed. It is best to record the addresses that are in the computer so they can be re-assigned when the operation is finished.

Enter 169.254.1.2 (which is the default address 169.254.1.1 plus 1) and Subnet mask is 255.255.0.0 and click OK > and then OK again. Bring up one of the approved web browsers (like Chrome) and enter http://169.254.1.1 and the Log-in page will appear.

With Apple OS X (10.7 and above), the steps are a bit different but essentially the same…Go to > System Preferences > Network > Ethernet > Configure IPv4: Manually > Enter in 169.254.1.2 and Subnet mask of

255.255.0.0 and click Apply. Bring up one of the approved web browsers (like Safari) and enter http://169.254.1.1 and the Log-in page will appear.

Windows 7 has its own set-up that is a bit different from Windows XP Pro, but similar in that the whole purpose of the first time set up is to give the HD-USB PTZ Camera an address that can be used over and over again by users or administrators to control the camera.

Whoops - Reset to Defaults: If for some reason the IP address was entered wrong or ne eds to be erased and re-entered, remember Rotary Switch position “C” on the lower USB resource card to RESET and RESTORE TO FACTORY DEFAULTS. Set the switch to “c” and is power cycle the camera to restore the default IP address. Move the switch back and start again.

Connect to the Local Area

Network or to a computer

with a Cross-over cable

WallVIEW HD-USB SR PTZ Camera System Document Number 342-0465 Rev. A 6 Page 15 of 28

WallVIEW HD-USB SR Camera System

SCREEN SHOT TOUR

Whether or not the network is DHCP and the Network Administrator has provided the DHCP address, or the Static IP routine is used, after entering the address on the address line the Camera Controls screen will come up. Below the functions and details are called out.

1) Pan, Tilt and Home Controls: These intuitive controls use the up/down arrows for camera tilt, the left/right arrows for camera pan and the center button to move the camera to the home position.

2) Zoom Control: The camera’s zoom lens can be controlled with the “+” to zoom-in and the “-“ button to zoom out.

3) Pan/Tilt and Zoom Speed Controls: The speed for both the Pan/Tilt and Zoom controls can be sped up for longer shots with the two (2) buttons in this section. For tighter shots, it is recommended that the slower speed is used.

4) Store Preset Button: Clicking the Store button opens up a Store Preset pop-up dialog box. To set presets, set up the camera shot, click on choice of preset number (1 through 6). The preset is stored and the dialog box closes.

5) Camera Presets: Six (6) presets can be recalled simply by clicking a preset nu mber.

6) Administration Menu: Clicking on the Administration menu bar, the Admin Log-in screen will appear. Default Admin password is password.

7) Vertical: The vertical button will reduce the size of the window for the user controls and remove the menu

tabs on the left side of the screen. The vertical sizing works well when using it with a soft-client codec. Examples of the vertical box are at the end of the tour.

WallVIEW HD-USB SR PTZ Camera System Document Number 342-0465 Rev. A 6 Page 16 of 28

➏

➊

➋

➌

➍

➎

Store Preset pop-up menu dramatization

➐

WallVIEW HD-USB SR Camera System

Admin Pages

Clicking on the Admin link button will open the Log-in window. Enter the default password on this line and click on Log-in.

After Log-in, the Admin link buttons are exposed and include Networking, Security, Diagnostics, System, Help and Logout Admin.

◄

◄ ◄

WallVIEW HD-USB SR PTZ Camera System Document Number 342-0465 Rev. A 6 Page 17 of 28

WallVIEW HD-USB SR Camera System

By clicking on the Networking link button, the Network Configuration and Network Interfaces are displayed. This is where the Network administrator assigns either DHCP or a Static address and the associated parameters.

By clicking on the Security link button, the Update Password screen is displayed. The default user password is blank and the Admin password is simply “password’. The user names are equally easy…user for User and admin for Admin (use lower case). The Network administrator can reassign the user password and the Admin password. There is only one User password and one Admin password.

◄

WallVIEW HD-USB SR PTZ Camera System Document Number 342-0465 Rev. A 6 Page 18 of 28

WallVIEW HD-USB SR Camera System

By clicking the Diagnostics link button, a set of self-diagnostics will be displayed. These diagnostics may help the Vaddio technical support team diagnose a problem with the HD-USB camera.

The System link button is where the Firmware Updates will be loaded. There will be several firmware updates and upgrades over the life of the camera.

◄

WallVIEW HD-USB SR PTZ Camera System Document Number 342-0465 Rev. A 6 Page 19 of 28

WallVIEW HD-USB SR Camera System

The Help link button informs the Administrator where to call or e-mail for Technical Support. One key part of this screen is the System Information. Please have the system information available when calling Tech Support

Finally, the Vertical button at the top right of the camera control page reduces the size of the camera control window and drops the menu bars to allow the controls to be open and on screen along with any soft-codec application without taking up too much space. The Full button returns it to normal size.

WallVIEW HD-USB SR PTZ Camera System Document Number 342-0465 Rev. A 6 Page 20 of 28

◄

TECHNICAL SUPPORT NOTE: Please work with your Network Administrator prior to calling Vaddio for technical support. Please have on site network personnel i nitiate tech support calls with Vaddio only.

◄

See Below for Vertical Effect

◄

on Menus

WallVIEW HD-USB SR Camera System

CONNECTING THE CAMERA TO THE PROGRAM OF CHOICE:

The HD-USB PTZ Camera is compatible with many programs and media players. The following is an attempt to generally describe the steps to plug in the HD-USB camera and get an image.

Skype Example

1) First, with a quality USB 2.0 cable, plug the USB-B port of the camera to the USB-A port of the computer. A pop up window on the computer monitor will display the following:

a. Found ClearVIEW HD-USB b. Found USB Composite Device c. Found USB Video Device

2) Open Skype and perform the following steps:

a. Open the Tools Menu and drop down to Options b. Click on Video Settings and under Webcam choose USB Video Device

The systems will negotiate the highest resolutions possible, depending on the computer speed, network quality, cabling etc..., and display the video signal of the camera. The camera can be controlled with the supplied Vaddio IR Remote Commander or through IP as described earlier through the came ras web pages.

Make a test call to ensure the system is working properly.

VLC Media Player Example

1) Same first step as above.

2) Open VLC Media Player and perform the following steps:

a. Click on the Media menu and drop down to Open Capture Device and click it. b. Under Device Name, go to the Video Device Name drop down and choose USB Video Device. c. Under Options, enter the Video Size as 1280x720 d. Click on Play e. From there, VLC needs some instruction on the aspect ratio, so click on Tools and drop down to

Aspect Ratio and drop down again to 16:9 for 720p (1280x720).

VLC is a powerful record/playback system and buffers the images so you will notice some delay in the way VLC displays the image.

With all the compatible software available, in general terms, the video device, aspect ratio, and resolution may need to be set manually the first time through initial set-up. Some systems are easier than others (like Skype) and others are more technical in nature and tend to do more stuff (like VLC).

WallVIEW HD-USB SR PTZ Camera System Document Number 342-0465 Rev. A 6 Page 21 of 28

WallVIEW HD-USB SR Camera System

TECHNICAL SPECIFICATIONS:

Part Numbers 999-6990-000 North America, 999-6990-001 International

Video Outputs

USB Interface

Network Interface

H.264 Resolutions (Release 2.0)

User Control

Supported Media Players

Supported Browsers Image Sensor

Minimum Illumination

Lens/ Focal Length

Horizontal Viewing Angle

Pan Range

Preset Positions Power Extension Module Includes

Active USB 2.0 Extension Cable P/N: 440-1005-020

General Information Operating

Temperature Dimensions /

Weight Software Release

Information

 USB 2.0 (MJPEG)

o Resolution up to 720p/30 USB 2.0 (MJPEG) o Use “HD VIDEO AND USB 2.0 VIDEO SELECT” rotary positions 0, 1, 4 &

5 for USB.2.0 Video only

 H.264 (IP)

o Resolution up to 1080p/30 (H.264 over IP & USB 2.0 - Release 2.0)

 Analog Component (YPbPr),

o Analog resolutions up to and including 1080p/60 (YPbPr)

 CVBS - Analog only

o 480i and 576i (4:3, LB and SQ)

Connector: Type-B, USB 2.0 Compliant, Supported Drivers: Standard UVC device (no custom drivers)

Connector: RJ-45, 10/100 Base-T, Supported Protocols: RTSP Streaming, HLS Streaming (apple’s variant of HTTP streaming) - Release 2

CIF, 640x480 (VGA), 480p, 720p/30 1080p/30 (1080p Ethernet only)

Vaddio IR Remote Commander, On Screen Display for camera set-up, RS-232, Ethernet (web page)

Windows Media Player, Apple Quick-Time and VLC Media Player

Internet Explorer 8 & 9, Safari 4 &5, Safari/iOS, Chrome, FireFox 1/3-Type Exmor High-speed,

Progressive Scan CMOS Sensor with 1.3 Megapixels

0.7 LUX (F1.6, 50IRE)

19X Optical Zoom, F=4.5mm wide to 85mm tele (F1.6-F2.9), Min. Focus Distance 1.0m

58.1° Wide End to 3.2° Tele End - 16:9 Format

Pan: +170 degrees to -170 degrees, Tilt: +90 degrees to -30 degrees, Invertible for Ceiling Mount

16 (internal), 6 recalled via IR Remote

 Power Extension Module with 5.5mm OD x 2.5mm ID coax power connector  24 VDC, 2.75 Amp switching power supply (100V-240V, 50 to 60 Hz) with power

cable

Jargy/Mobile Computing 20m (65.6’) Port Powered USB 2.0 Extension Cable Connectors: Type-A Male for Host Side, Type-A Female for device side 1’ (305mm) Type-B Male to Type-A Male USB 2.0 cable included (see Diagrams)

32° to 104° F (0° to 40° C) / 20% to 80% Relative Humidity

7.81” (198.37mm) H x 6.67” (169.42mm) W x 7.057” (179.25. mm) D / 6.04 lbs. (2.7397kg.)

Release 1.0: Includes USB 2.0 Outputs and Analog Outputs simultaneously on and ready to use. Ethernet control via an internal web page and upgrading software capability is active. Release 2.0: H.264 Streaming will be activated for Ethernet port.

WallVIEW HD-USB SR PTZ Camera System Document Number 342-0465 Rev. A 6 Page 22 of 28

WallVIEW HD-USB SR Camera System

COMPLIANCE AND CE DECLARATION OF CONFORMITY: CLEARVIEW HD-USB PTZ CAMERA

Compliance testing was performed to the following regulations:

 FCC Part15, Sections 15.107, 15.109 Subpart B Class A  ICES-003 ISSUE 4, 2004 Class A  EN55022 A1 2007 Class A  EMC Directive 2004/108/EC Class A  IEC 60950-1:2005 (2nd Edition); Am 1:2009 Class A  EN 60950-1:2006+A11:2009+A1:2010+A12:2011 Cla ss A

  FCC Part 15 Compliance

 This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to

Part 15, Subpart B, of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his/her own expense.

  Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This

device must accept any interference including interference that may cause undesired operation of the device.

 Changes or modifications not expressly approved by Vaddio can affect emission compliance and could void

the user’s authority to operate this equipment.

ICES-003 Compliance ICES-003, Issue 4: 2004

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. Le présent appareil numérique n’emet pas de bruits radioélectriques dépassant les limites applicables aux appareils numeriques de la classe B préscrites dans le Règlement sur le brouillage radioélectrique édicte par le ministère des Communications du Canada.

European Compliance

This product has been evaluated for Electromagnetic Compatibility under the EMC Directive for Emissions a nd Immunity and meets the requirements for a Class A digital device. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Standard(s) To Which Conformity Is Declared: EMC Directive 2004/108/EC

EN55024/A2:2003 Information Technology Equipment

Immunity Characteristics Limits and Methods of Measurement

 EN 61000-4-2: 1995 + Amendments A1: 1998 + A2: 2001 Electrostatic Discharge  EN 61000-4-3: 2006 + A1: 2008 Radiated Immunity  EN 61000-4-4: 2004 + Corrigendum 2006 Electrical Fast Transients  EN 61000-4-5: 2006 Surge Immunity  EN 61000-4-6: 2009 Conducted Immunity  EN 61000-4-8: 2010 Power Fre quency Magnetic Field  EN 61000-4-11: Second Edition: 2004 Voltage Dips, Interrupts and Fluctuations  IEC 60950-1:2005 (2nd Edition); Am 1:2009 Information technology equipment - Safety  EN 60950-1:2006+A11:2009+A1:2010+A12:2011 Information technology equipment - Safety

WallVIEW HD-USB SR PTZ Camera System Document Number 342-0465 Rev. A 6 Page 23 of 28

WallVIEW HD-USB SR Camera System

WARRANTY INFORMATION: (See Vaddio Warranty, Service and Return Policies posted on vaddio.com for complete details):

Hardware* Warranty: One year limited warranty on all parts. Vaddio warrants this product against d efects in materials and

workmanship for a period of one year from t he day of purchase from Va ddio. If Vaddio receives notice of such defects during the warranty period, they will, at their option, repair or replace products that prove to be defective. Please see Vaddio’s Service Terms and Conditions at vaddio.com for specific details and policies.

Exclusions: The above warranty shall not apply to defects resulting from: improper or inadequate maintenance by the customer, customer applied software or interfacing, unauthorized modifications or misuse, operation outside the normal environmental specifications for the product, use of the incorrect power supply, improper installation (plugging things in wrong), improper extension of the power supply cable or improper site operation and maintenance.

Vaddio Customer Service: Vaddio will test, repair, or replace the product or pro ducts without charge if the unit is under warranty and is found to be defective. If the product is out of warranty, Vaddio will test then repair the product or products. T he cost of parts and labor charge will be estimated by a tech nician an d confirmed by the customer prior to repair. All components must be returned for testing as a complete unit. Vaddio will not accept res ponsibilit y for shipm ent after it has left the pr emises. Vaddio will only advance replace out of box failures or r andom equipment failures up to 30 days after the purchase date (not the install date).

Vaddio Technical Support: Vaddio technicians will determine and discuss with the customer the criteria for repair costs and/or replacement. Vaddio Technical Support can be contacted through one of the follo wing resources: e-mail support at

support@vaddio.com or online at www.vaddio.com.

Return Material Authorization (RMA) Number: Before returning a product for repair or replacement, request an RMA from Vaddio’s technical support. Provide a technician with a return phone number, e-mail address, shipping address, and product serial numbers and describe the reason for repairs or retur ns as well as the date of purchase and proof of purchase. Include your assigned RMA number in all correspondence with Vaddio. Write your assigned RMA number on the clearly on the shipping label when returning the product. All products returned for credit are subject to a restocking charge without exception.

Voided Warranty: The warranty does not apply if the original serial number has been removed or if the product has been disassembled or damaged through misuse, accident, modifications, or unauthoriz ed repai r. Cutting the po wer supply cabl e on the secondary side (low voltage side) to extend the power to the device voids the warranty for that device.

Shipping and Handling: Vaddio will not pay for inbound shipping transportation or insurance charges or accept any responsibility for laws and ordinances from inbound transit. Vaddio will pay for outbound shipping, transportation, and insurance charges for all items under warranty but will not assume responsibility for loss and/or damage by the outbound freight carrier. If the return shipment appears damaged, retain the original boxes and p acking material for inspection

by the carrier. Contact your carrier immediately. Products Not Under Warranty: Payment arrangements are required before outbound shipment for all out of warranty

products.

*Vaddio manufactures its hardware products from parts and components that are new or equivalent to new in accordance with industry standard practices.

Other General Information: Care and Cleaning

Do not attempt to take this product apart at any time. There are no user-serviceable components inside.

 Do not spill liquids in the product  Keep this device away from food and liquid  For smears or smudges on the product, wipe with a clean, soft cloth  Use a lens cleaner on the lens  Do not use any abrasive chemicals.

Operating and Storage Conditions:

Do not store or operate the device under the following conditions:

 Temperatures above 40°C (104°F) or temperatures below 0°C (32°F)  High humidity, condensing or wet environments  In swimming pools or grain elevators  In inclement weather  Dry environments with an excess of static discharge  In a semi-tractor trailer or refrigerator truck  Under severe vibration

WallVIEW HD-USB SR PTZ Camera System Document Number 342-0465 Rev. A 6 Page 24 of 28

WallVIEW HD-USB SR Camera System

APPENDIX 1: COMMUNICATION SPECIFICATION

Communication Speed: 9600 bps (default) Start bit: 1 Stop bit: 1 Data bits: 8 Parity: None No Flow control

12345678

NOTE: The Vaddio ClearVIEW HD-USB Control Protocol is similar, but not identical to the Sony® VISCA™ command set and is not compatible with Vaddio Joysticks. This is an abbreviated Command set intended to give external control systems basic control over the camera. This list is not the same list as found in the other ClearVIEW (HD-18, HD-19 and HD-20) cameras.

HD-USB Command List

Command Set Command Command Packet Comments

Address Set Broadcast 88 30 01 FF Address Set (Daisy chain) IF_Clear Broadcast 88 01 00 01 FF IF Clear Command Cancel 8x 2p FF p:socket number(1,2) CAM_Power On

Off(Standby)

CAM_Zoom Stop

Tele(Standard) Wide(Standard) Tele(Variable) Wide(Variable) Direct Direct(Variable)

CAM_Focus Stop

Far(Standard) Near(Standard) Far(Variable) Near(Variable) AutoFocus ManualFocus Auto/Manual Direct

CAM_Backlight On

Off

CAM_Memory Reset

Set Recall

Pan-tiltDrive Up

Down Left Right UpLeft UpRight DownLeft DownRight Stop Absolute Position

Home Reset

Tally On

Off

Preset Pan Speed Pan/Tilt/Zoom Speed 81 01 7E 01 0B WW SS ZZ FF WW: Pan Speed (0x01-0x18)

*Zoom and Focus Data:

CAM_Zoom: Range(0x000–0x6B3) CAM_Focus: Range (0x000-0xC000) dependent on Zoom Position

**Additional Information:

Pan Range: 8044 – 7FBC (-32,700 to +32,700) Tilt Range: E891 – 4C2B (-5,999 to +19,499)

8x 01 04 00 02 FF 8x 01 04 00 03 FF

8x 01 04 07 00 FF 8x 01 04 07 02 FF 8x 01 04 07 03 FF 8x 01 04 07 2p FF 8x 01 04 07 3p FF 8x 01 04 47 0p 0q 0r 0s FF 8x 01 7E 01 4A 0v 0p 0q 0r 0s FF

8x 01 04 08 00 FF 8x 01 04 08 02 FF 8x 01 04 08 03 FF 8x 01 04 08 2p FF 8x 01 04 08 3p FF 8x 01 04 38 02 FF 8x 01 04 38 03 FF 8x 01 04 38 10 FF 8x 01 04 48 0p 0q 0r 0s FF

8x 01 04 33 02 FF 8x 01 04 33 03 FF

8x 01 04 3F 00 0p FF 8x 01 04 3F 01 0p FF 8x01 04 3F 02 0p FF

8x 01 06 01 VV WW 03 01 FF 8x 01 06 01 VV WW 03 02 FF 8x 01 06 01 VV WW 01 03 FF 8x 01 06 01 VV WW 02 03 FF 8x 01 06 01 VV WW 01 01 FF 8x 01 06 01 VV WW 02 01 FF 8x 01 06 01 VV WW 01 02 FF 8x 01 06 01 VV WW 02 02 FF 8x 01 06 01 VV WW 03 03 FF 81 01 06 02 VV WW 0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z FF 0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z FF 8x 01 06 04 FF 81 01 06 05 FF

8x 01 7E 01 0A 00 02 FF 8x 01 7E 01 0A 00 03 FF

WallVIEW HD-USB SR PTZ Camera System Document Number 342-0465 Rev. A 6 Page 25 of 28

Pin # RJ-45 RS-232 and IR Out Pins

1) Unused

2) Unused

3) Unused

4) Unused

5) Unused

6) GND (GND of IR Short Range - Pin 3)

7) RXD (from TXD of control source)

8) TXD (to RXD of control source)

Power On/Off

pqrs: Zoom Position* v:(Speed) 0-7

pqrs: Focus position*

p:Memory No(=0-0xe) WW: Pan Speed (0x01-0x18)

VV:Tilt Speed(0x01-0x14)

YYYY: Pan Position** ZZZZ: Tilt Position**

SS:Tilt Speed(0x01-0x14) ZZ:Zoom Speed(0-7);

WallVIEW HD-USB SR Camera System

HD-USB Inquiry List

Inquiry Command Command Response Packet Comments

CAM_PowerInq 8x 09 04 00 FF y0 50 02 FF

y0 50 03 FF CAM_ZoomPosInq 8x 09 04 47 FF y0 50 0p 0q 0r 0s FF pqr: 0-0x6B3 CAM_FocusPosInq 8x 09 04 48 FF y0 50 0p 0q 0r 0s FF pqrs: Focus Position CAM_BacklightModeInq 8x 09 04 33 FF y0 50 02 FF

y0 50 03 FF CAM_MemoryInq 8x 09 04 3F FF y0 50 0p FF p:Preset 0-0xf Pan-TiltMaxSpeedInq 8x 09 06 11 FF y0 50 pp qq FF pp:Pan 0x01-0x18

Pan-tiltPositionInq 8x 09 06 12 FF FF y0 50 0p 0p 0p 0p 0q 0q 0q 0q FF pppp: Pan 0x8044-0x7FB2

TallyInq 8x 09 7E 01 0A FF y0 50 02 FF

y0 50 03 FF PresetSpeedInq 8x 09 7E 01 0B FF y0 50 pp qq rr FF pp:Pan 0x01-0x18

Motor Config 8x 09 7E 01 70 FF y0 50 00 FF

y0 50 01 FF

On Off(Standby)

On Off

qq:Tilt 0x01-0x14

qqqq: Tilt 0xE890-0x4C2C On

Off

qq:Tilt 0x01-0x14 rr:Zoom 0x00-0x07

Hard Motor Stops Soft Motor Stops

A FINAL NOTE ABOUT SOFTWARE RELEASES:

Since there is better than 1/2 a page to fill up here, a note regarding the software releases and the intent of the product lifecycle of the HD-USB camera is included.

The intent of releasing the HD-USB camera with full USB 2.0 implementation and waiting for Release 2.0 for full H.264 implementation was to ensure that the H.264 streaming applications could all be adequately tested and confirmed 100% operational.

The USB 2.0 implementation is in high demand and we are ready for Release 1.0 of the camera strictly for USB

2.0 soft client conferencing programs. While there is some rudimentary Ethernet functionality in Release 1.0, it was included mainly as a means to

upgrade/update the software for future software releases and added functionality. In any case, it is recommended that anyone using the Ethernet connectivity use the Static IP addressing for now.

WallVIEW HD-USB SR PTZ Camera System Document Number 342-0465 Rev. A 6 Page 26 of 28

WallVIEW HD-USB SR Camera System

HD-USB System Notes:

WallVIEW HD-USB SR PTZ Camera System Document Number 342-0465 Rev. A 6 Page 27 of 28

WallVIEW HD-USB SR Camera System

©2012 Vaddio - All Rights Reserved. Reproduction in whole or in part without written permission is prohibited. Specifications and pricing are subject to change without notice. Vaddio, ClearVIEW, WallVIEW, EZCamera, CONCEAL, EasyTalk, EasyMic, EasyUSB and PowerRite are trademarks of Vaddio. All other trademarks are property of their respective owners. Document 342-0465 Rev. A

WallVIEW HD-USB SR PTZ Camera System Document Number 342-0465 Rev. A 6 Page 28 of 28

Toll Free: 800-572-2011 ▪ Phone: 763-971-4400 ▪ FAX: 763-971-4464

9433 Science Center Drive, Minneapolis, MN 55428

www.vaddio.com

VADDIO WallVIEW, 999-6994-000, 999-6994-001 Installation And User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual