VADDIO HD-18, WallVIEW HD-18, WALLVIEW HD-18 999-6905-000, WALLVIEW HD-18 999-6905-001, 999-6905-000 Installation And User Manual

Installation and User Guide

Camera and Electronic Products for Integrators

Vaddio™ WallVIEW™ HD-18

High Definition PTZ Camera featuring the HD-18 Quick-Connect™ SR

Model Number 999-6905-000W (North America)
Model Number 999-6905-001W (International)
Arctic White Version

HD-18 Quick-Connect SR Interface

Model Number 999-6905-000 (North America)
Model Number 999-6905-001 (International)

©2010 Vaddio - All Rights Reserved. WallVIEW HD-18 - Document Number 341-888 Rev. C

WallVIEW HD-18

WallVIEW HD-18 Overview

With the WallVIEW HD-18 PTZ camera and CAT-5 cabling system,
Vaddio delivers a system that allows for easy installation and integration
of camera systems. The camera is built around a 1.3 megapixel, 1/3”
CCD with an 18x optical zoom lens, making it the ideal choice for a wide
range of high definition video applications. In addition to the component
HD output (720p, 1080i or 1080p), the camera comes with a
simultaneous composite SD output (NTSC or PAL).

Because the camera module is built around a CCD image sensor, the
HD-18 is excellent in low-light situations, with a 1.8 lux rating. In
addition, the video signal to noise ratio output of the camera is greater
than 50dB, delivering clean, clear video.

The 7-element Wide Dynamic Zoom lens allows WallVIEW HD-18 to capture a wide angle of view (55.2°)
enough to view everyone at a conference room table, as well as capture an individual from a long
distance (3.2°). The zoom range provides greater flexibility for a wide variety of applications. Pan range
is +170 to -170 degrees, and Tilt range is -30 to +90 degrees.

Paired with the HD-18 camera is Vaddio’s Quick-Connect SR breakout box. Installed at the equipment
headend, the Quick-Connect SR provides power to the camera and component HD video (no SD output
on the Quick-Connect SR) from the camera up to 100 feet over a single CAT-5 cable. In addition, IR
signals (modulated or non-modulated) and RS-232 control can be passed from the camera to third-party
equipment, such as videoconference codecs on a second CAT-5 cable.

The WallVIEW HD-18 is and exceptional camera system for integration projects, since no power supply
is required at the camera location. Use the WallVIEW HD-18 for high definition camera applications, such
as houses of worship, corporate boardrooms, live event production and distance-learning.

Intended Use:

Before operating the Vaddio WallVIEW HD-18, please read the entire manual thoroughly. The system
was designed, built and tested for use indoors, and with the provided power supply and cabling. The use
of a power supply other than the one provided or outdoor operation has not been tested and could
damage the camera and/or create a potentially unsafe operating condition.

Important Safeguards:

Read and understand all instructions before using. Do not operate any device if it has been dropped or
damaged. In this case, a Vaddio technician must examine the product before operating. To reduce the
risk of electric shock, do not immerse in water or other liquids and avoid extremely humid conditions.

Save These Instructions:

The information contained in this manual will help you install and operate your Vaddio WallVIEW HD-18.
If these instructions are misplaced, Vaddio keeps copies of Specifications, Installation and User Guides
and most pertinent product drawings for the Vaddio product line on the Vaddio website. These
documents can be downloaded from www.vaddio.com

Use only the power supply provided with the WallVIEW HD-18 sy stem.
Use of any unauthorized power supply will void any and all warranties.

Do not use “pass-thru” RJ-45 connectors. Use standard RJ-45
connectors for best results.

free of charge.

WallVIEW HD-18 Manual 341-888 Rev. C Page 2 of 16

WallVIEW HD-18

UNPACKING:

Carefully remove the device and all of the parts from the packaging.
Unpack and identify the following parts:

• One (1) WallVIEW HD-18 Camera

• One (1) Quick-Connect SR breakout box

• One (1) Vaddio PowerRite™ 24 VDC, 2 Amp Power Supply

• One (1) EZCamera™ Control Adapter (RJ-45 to DB-9)

• One (1) Wall Mount and Mounting Hardware

• One (1) AC Cord Set (US - North America or UK & Europe - International)

• Documentation and Manual

Figure 2: WallVIEW HD-18 camera (front)

1

3

2 4

Front of WallVIEW HD-18

1. Camera – A 1/3”, 1.3 megapixel HD image sensor is combined with an 18x optical zoom lens, for
capturing high-quality video.

2. Tally Light – A tally light is illuminated when the camera receives a VISCA command from an
external control system and tally is triggered.

3. IR Sensors – Dual IR sensors are built into the front of the WallVIEW HD-18 to receive IR signals
from the IR remote control supplied with the camera.

4. Power Light – A power light is illuminated when the camera is turned on.

Compatible Switchers and Joystick Controllers:

ProductionVIEW HD

(999-5600-000)

ControlVIEW XHD

(999-5672-000)

Precision Camera Controller

(999-5700-000)

WallVIEW HD-18 Manual 341-888 Rev. C Page 3 of 16

WallVIEW HD-18

Figure 3: WallVIEW HD-18 camera (back)

5

9

6

10

7

11

8

Rear of WallVIEW HD-18

5. RS-232 In & IR Out – The RS-232 accepts modified VISCA™ protocol for camera control, as well
as transmits IR signaling received by the IR receivers, which can be transmitted to third party
devices.

6. DIP Switch Settings – Settings for IR remote, baud rate, SD output format, image flip can be
configured on these switches. See page 6 for additional information switch settings.

7. HD Video Select – A rotary switch allows the user to choose the component HD output video
resolution and format. See page 6 for additional information on switch settings.

8. 12 VDC Input – NOTE: The power input is not used with the WallVIEW HD-18 system. This is only
used on the standard, ClearVIEW HD-18 camera.

9. YPbPr Video Output – Component HD video is fed through the DB-15 connector.

10. SD Video Output – Standard definition video is fed through the BNC connector.

11. EZ Port – CAT-5 cable (up to 100 feet) is connected to the Quick-Connect SR. The EZ-Port
supplies power to the camera and delivers component HD video up to 100 feet.

12. Slot for Optional Cards – Optional slot cards can be plugged into the WallVIEW HD-18 camera
through the slot in the back of the camera base.

12

WallVIEW HD-18 Manual 341-888 Rev. C Page 4 of 16

WallVIEW HD-18

Figure 4: Quick-Connect SR (rear)

13

14

15

17

16

13. Power Input – The 24 VDC power adapter powers the Quick-Connect SR and also sends power to
the HD-18 camera.

14. Power & HD Video – The CAT-5 connection that extends to the EZ-Port Power/Video connector on
the HD-18 camera. Maximum distance on the CAT-5 cable is 100 feet (30.5 m).

15. HD Video Output – DB-15 connector that outputs the component HD video extended from the
camera over CAT-5 cabling.

16. IR Output – With the IR pass-thru turned on at the camera (see Camera Settings section), send IR
from third-party IR remote controls to third-party equipment, such as videoconference codecs. IR
can be transmitted as either modulated or non-modulated signals for added flexibility.

17. RS-232 Input & Output Jacks – When using the IR pass-thru function, the IR signals are pulled
from the CAT-5 RS-232 cable and delivered as modulated and non-modulated signals to the IR
Output ports.

First Time Set-up with the WallVIEW HD-18:

WallVIEW HD-18 was designed to be exceptionally easy to use and operate. There is documentation at
the back of the manual for pin-outs for all of the connectors on the WallVIEW HD-18 camera.

Getting Started:

First, set up the HD and SD output resolutions for the camera, along with IR output, baud rate and image
flip. On the next page are the options for the switches that are found on the back of the camera.

WallVIEW HD-18 Manual 341-888 Rev. C Page 5 of 16

WallVIEW HD-18

Figure 5: Dip Switch and HD Video Output Resolution Setting Options for the HD-18 Camera

IR 1

1 & 2 UP

IR 2ONIR 3

ON

21

12

DIP SWITCH SETTINGS

IR
OUT
OFF

ON

3

3

9600

bps

38400

bps

4

4

SD

NTSC

SD

PAL

5

56

SD
LB

7

7

IMAGE

FLIP
OFF

ON ON

8

SD 4:3

6 & 7 UP

SD

SQ

68109

TEST

10

BARS

OFF

OFF

ON

910

0
1
2
3
4
5
6
7

HD VIDEO SELECT

720p/59.94

1080i/59.94

1080p/59.94

1080p/60

720p/50

1080i/50

1080p/50

480i/29.97

8
9

A
B
C
D
E
F

576i/25

1080p/30
1080p/25

Note: The Test Bars are non standard, but are 75% YCbCr Color Bars and are intended as a

convenience for testing the signal path only.

• IR 1, 2 & 3: These settings, using switches 1 & 2, determine the IR frequency of the IR remote control
that was supplied with your camera. The IR remote has the capability of operating up to three different
PTZ cameras from one remote, using the selector buttons at the top of the remote.

• IR Out: The IR output is sent on the RJ-45, RS-232 jack on the back of the camera. Turning on the IR
output will allow IR signals to be transmitted over the CAT-5 cable.

• Baud Rate: The options for baud rate are either 9600 or 38,400 for RS-232.

• SD Output Frequency: Select either NTSC or PAL as the output for the camera’s SD signal that is

transmitted on the BNC connector.

• SD Output Size: Three options are available for the SD output, select from crop, squeeze or letterbox.

• Image Flip: Turing Image Flip on (switch down), will allow the camera to be inverted.

• Test Bars: Turning this switch on will override the camera video output and send test video bars from

the camera to the CCU to allow more accurate setting of the video level at the CCU.

• Switch 10: This switch is unused, and should be left in the OFF position.

RS-232 Cabling

For RS-232, use a standard CAT-5 cable (568B termination for RJ-45 connectors) from the RS-232 port
on the back of a Vaddio ProductionVIEW camera controller or switcher. If the camera will be connected
to a third-party control system (such as AMX or Crestron), a DB-9 to RJ-45 adapter cable is supplied with
the camera for RS-232. Use of pass-thru RJ-45 connectors should not be used (see notice on page 2).

Videoconference Codecs and RS-232

Depending on the codec that is used, and which RS-232 port is used with a codec, special DB-9 to RJ-45
adapters may sometimes be required. Refer to Vaddio’s website for Tech Notes on the WallVIEW HD-18
page on specific diagrams for wiring the camera to videoconference codecs. Any special adapters and
configuration information will be noted on the Tech Note.

INSTALLATION

The WallVIEW HD-18 product was specifically designed for installation on a vertical wall surface with Cat.
5 cable connectivity for Power, Video and Control signaling (two cables are required). Installation is
simplified in that no custom 8-Pin mini-din cables or expensive S-Video plenum cables are needed and
no power outlets are required near the camera bracket. All cabling is routed to the head-end using Cat. 5

cables.

WallVIEW HD-18 Manual 341-888 Rev. C Page 6 of 16

WallVIEW HD-18

Before Installing

• Locate the camera mounting location paying close attention to camera viewing angles, lighting

conditions, possible line of site obstructions, and checking for in-wall obstructions where the camera
is to be mounted. Pick a mounting location to optimize the performance of the camera.

• Pre-wire all cabling as required (see wiring diagram examples).

• The Thin Profile Wall Mount for the WallVIEW HD-18 can be mounted directly to a 2-gang wall box or

can be mounted to the drywall using four dry wall anchors.

Figure 6: Standard wiring configuration of the camera to a Vaddio Joystick controller.

Rear
Panel
HD-18

RS-232
Cat 5e

YPbPr & Power on one (1) Cat 5e up to 100’ (30.48m)

← YPbPr

Power

→

Rear Panel
HD-18 QC SR
(Equipment
Head-end)

YPbPr

24V - 2A
Power Supply

HD Monitor

(Simulated Feed)

ProductionVIEW Precision Camera Controller

WallVIEW HD-18 Manual 341-888 Rev. C Page 7 of 16

WallVIEW HD-18

MOUNTING AND INSTALLATION INSTRUCTIONS
Step 1:

After determining the optimum location of the camera system, route the required 2 (two) Cat. 5 cables
from the camera to the Quick-Connect Pro interface located at the head-end. The two Cat. 5 cables
should feed-through the oval slot located on the rear flange of the wall mount. If the bracket is to be
mounted on a 2-gang wall box, use the screws supplied with the wall box cover plate to attach the Thin
Profile Wall Mount. If mounting to the drywall with wall anchors, use four (4) quality wall anchors. The
mounting holes are slotted and are 90° opposing to provide easy leveling. Level the mount and tighten

the mounting screws.

Step 2:

Follow the sample wiring diagram on the previous page for connecting the Cat. 5 cables to the camera
and Quick-Connect Short Range, using a compatible Vaddio ProductionVIEW joystick camera controller.
Additional diagrams are available on our website for installation with a variety of videoconference codecs,
utilizing the RS-232 Input and Output connectors for IR signaling.

Note: Check all Cat. 5 cables for continuity in advance of the final connection. Plugging the EZ
POWER/VIDEO Cat. 5 Cable into the wrong RJ-45 may cause damage to the camera system and
void the warranty.

Step 3:

Place the camera onto the camera mount and use the ¼”-20 screws to secure the camera to the mount.

Step 4:

Connect the Vaddio 24 VDC power supply to an AC outlet. Power will travel down the Power/Video Cat.
5 cable to the camera. The camera will “Home” to a centered position ready for control information from
the IR remote control or RS-232 camera controller of the integrators’ choice. To insure proper continuity
of control and operation of the cameras, the RS-232 controller (control system or joystick) should be
powered on after the camera.

IMPORTANT NOTE:

Strain relief for the 15-pin connector is highly recommended on the DE-15 connector on the back of the
WallVIEW HD-18 system.

Figure 7: Sample diagram

showing WallVIEW HD-18
connected to a Polycom
HDX-9004 Codec.

WallVIEW HD-18 Manual 341-888 Rev. C Page 8 of 16

NOTE: For additional diagrams and
configurations, see the Tech Notes under
the ClearVIEW HD-18, WallVIEW HD-18
and WallVIEW CCU HD-18 at vaddio.com

WallVIEW HD-18

Compliance and CE Declaration of Conformity

FCC Part 15 Compliance

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his/her own expense.

Operation is subject to the following two conditions: (1) This device may not cause interference, and (2)
This device must accept any interference including interference that may cause undesired operation of
the device.

Changes or modifications not expressly approved by Vaddio can affect emission compliance and could
void the user’s authority to operate this equipment.

ICES-003 Compliance

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus
set out in the Radio Interference Regulations of the Canadian Department of Communications.
Le présent appareil numérique n’emet pas de bruits radioélectriques dépassant les limites applicables
aux appareils numeriques de la classe A préscrites dans le Règlement sur le brouillage radioélectrique
édicte par le ministère des Communications du Canada.

European Compliance

This product has been evaluated for Electromagnetic Compatibility under the EMC Directive for Emissions and
Immunity and meets the requirements for a Class A digital device. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate measures.

Standard(s) To Which Conformity Is Declared:
EMC Directive 2004/108/EC

EN 55022 A: 2006 + A1 2007 (CISPR 22:2005/A1:2005) Conducted and Radiated Emissions

 AS/NZS CISPR 22: 2006, Australia and New Zealand - Conducted and Radiated Emissions

 VCCI V-3/2009.04, Japan - Conducted and Radiated Emissions

EN 55024: 1998 + Amendments A1: 2001 + A2: 2003 - Electromagnetic Compatibility - Immunity
EN 61000-4-2 Electrostatic Discharge
EN 61000-4-3 Radiated Immunity
EN 61000-4-4 Electrical Fast Transients
EN 61000-4-5 Surge Immunity
EN 61000-4-6 Conducted Immunity
EN 61000-4-8 Power Frequency Magnetic Field
EN 61000-4-11 Voltage Dips, Interrupts and Fluctuations

WallVIEW HD-18 Manual 341-888 Rev. C Page 9 of 16

WallVIEW HD-18

Warranty Information:

Hardware* Warranty - One year limited warranty on all parts. Vaddio warrants this product against defects in

materials and workmanship for a period of one year from the day of purchase from Vaddio. If Vaddio receives notice
of such defects during the warranty period, they will, at their option, repair or replace products that prove to be
defective.

Exclusions - The above warranty shall not apply to defects resulting from: improper or inadequate maintenance by

the customer, customer applied software or interfacing, unauthorized modifications or misuse, operation outside the
normal environmental specifications for the product, use of the incorrect power supply, improper extension of the
power supply cable or improper site operation and maintenance.

Vaddio Customer service – Vaddio will test, repair, or replace the product or products without charge if the unit is

under warranty and is found to be defective. If the product is out of warranty, Vaddio will test then repair the product
or products. The cost of parts and labor charge will be estimated by a technician and confirmed by the customer prior
to repair. All components must be returned for testing as a complete unit. Vaddio will not accept responsibility for
shipment after it has left the premises.

Vaddio Technical support - Vaddio technicians will determine and discuss with the customer the criteria for repair

costs and/or replacement. Vaddio Technical Support can be contacted through one of the following resources: e-mail
support at [e-mail] or online at www.vaddio.com

Return Material Authorization (RMA) number - Before returning a product for repair or replacement, request an

RMA from Vaddio’s technical support. Provide a technician with a return phone number, e-mail address, shipping
address, and product serial numbers and describe the reason for repairs or returns as well as the date of purchase
and proof of purchase. Include your assigned RMA number in all correspondence with Vaddio. Write your assigned
RMA number on the outside of the box when returning the product.

Voided warranty – The warranty does not apply if the original serial number has been removed or if the product has

been disassembled or damaged through misuse, accident, modifications, or unauthorized repair. Cutting the power
supply cable on the secondary side (low voltage side) to extend the power to the device (camera or controller) voids
the warranty for that device.

Shipping and handling - Vaddio will not pay for inbound shipping transportation or insurance charges or accept any

responsibility for laws and ordinances from inbound transit. Vaddio will pay for outbound shipping, transportation, and
insurance charges for all items under warranty but will not assume responsibility for loss and/or damage by the
outbound freight carrier.

• If the return shipment appears damaged, retain the original boxes and packing material for inspection by the carrier.

Contact your carrier immediately.

Products not under warranty - Payment arrangements are required before outbound shipment for all out of

warranty products.

*Vaddio manufactures its hardware products from parts and components that are new or equivalent to new in
accordance with industry standard practices.

Other General Information:
Care and Cleaning

Do not attempt to take this product apart at any time. There are no user-serviceable components inside.

• Do not spill liquids in the WallVIEW HD-18

• Keep this device away from food and liquid

• For smears or smudges on the console, wipe with a clean, soft cloth with a light duty household cleaner that

leaves no residue. Repeated use of a “Windex®” type product with vigorous pressure may remove some of
the silk screening and this will void the warranty.

• Do not use any abrasive chemicals.

Operating and Storage Conditions:

Do not store or operate the WallVIEW HD-18 under the following conditions:

• Temperatures above 40°C (104°F) or temperatures below 0°C (32°F)

• High humidity, condensing or wet environments or In inclement weather

• Dusty environments

• Under severe vibration

.

WallVIEW HD-18 Manual 341-888 Rev. C Page 10 of 16

WallVIEW HD-18

WallVIEW HD-18

Part Numbers WallVIEW HD-18 999-6905-000 (North America)

• Vaddio ClearVIEW HD-18

Image Device 1/3” CCD
Picture Elements 1.3 Megapixels
Signal System HD: 1080p, 1080i or 720p @ 59.94; 1080p @ 60; 1080p, 1080i or 720p @ 50

Lens 18x Optical Zoom
Focal Length f=4.7 to 84.6mm
Horizontal Viewing Angle 3.2 to 55.2 degrees (16:9)
Frame Delay 1 frame
Video S/N Ratio >50 dB
Invertible Yes
Minimum Illumination 1.8 lux
Control Protocol VISCA
Serial Communication RS-232 (9600 or 38,400)
Pan Range +170 degrees to -170 degrees
Tilt Range +90 degrees to -30 degrees
Pan/Tilt Speed 0.25° to 60° degrees/second
Preset Positions 16 (internal), 6 recalled via IR Remote
Weight 5.8 lbs. (2.63 kg.)

• Quick-Connect Short Range Interface (SR)

Connectors Power Connector: 5.5mm OD, 2.5mm ID coaxial connector

Cat. 5 Cable Distance Up to 100’ (30.5m)
Power Supply 24 VDC, 2 Amp
Dimensions 1-RU Rack Mount - 1.75” H x 5.5” W x 6” D (4.45 cm x 14 cm x 15.2 cm)

• Thin Profile Wall Mount HD-18

Materials 12-Gauge CRS with Black Powder Coat Paint
Dimensions 5.125” H x 6.75” W x 10” D (13 cm x 17.15 cm x 25.4 cm)
Weight Approx. 2.4 lbs. (1.1kg)

The WallVIEW HD-18 PTZ offers the following accessories for a complete, professional installation.

WallVIEW HD-18 999-6905-000W (Arctic White - North America)
WallVIEW HD-18 999-6905-001 (INT’L)
WallVIEW HD-18 999-6905-001W (Arctic White - INT’L)

SD: Composite NTSC or PAL (simultaneous with HD) NOTE: SD output not on Quick-Connect SR

Power/Video RJ-45: Supplies power to, and component HD from the camera, up to 100 feet
Video Output: DE-15 connector for HD Analog Component (Y,PB,PR) video only – no SD video
IR Output: Transmits modulated or non-modulated IR signals received from the HD-18 IR receiver
Control In RJ-45: Accepts RS-232 from ProductionVIEW or other non-daisy-chain control systems
Control Out RJ-45: Sends RS-232 from Quick-Connect SR to the camera

TANDBERG RS-232 Adapter
999-1002-232

Polycom RS-232 Adapter
999-1003-232

Polycom HDX 8000 Series Adapter
999-1006-232

Blank Panel for Quick-Connect SR
998-6000-002

15-pin to Male BNC output cable
440-5600-001 (3 ft.)
440-5600-002 (6 ft.)
440-5600-003 (7 inch.)

Drop Down Ceiling Mount
535-2225-296

WallVIEW HD-18 Manual 341-888 Rev. C Page 11 of 16

WallVIEW HD-18

Appendix 1:

Video Pin-out Table for WallVIEW HD-18

Pin YPbPr

1 Pr
2 Y
3 Pb
4 ­5 ­6 Pr GND
7 Y GND
8 Pb GND

9 ­10 ­11 ­12 ­13 ­14 ­15 -

EZCamera Power & HD Video RJ-45 Connector Pin-outs
For HD-18 Camera and Quick-Connect HD-18 SR (568B Wiring Standard)

Pin YPbPr

1 Power+

2 Power-

3 Y+

4 PB+

5 PB GND

6 Y GND

7 PR+

8 PR-

12345678

Appendix 2: Camera Dimensions

WallVIEW HD-18 Manual 341-888 Rev. C Page 12 of 16

WallVIEW HD-18

Appendix 3: Communication Specification

Communication Speed: 9600 bps (default)

Start bit: 1
Stop bit: 1
Data bits: 8
Parity: None

12345678

No Flow control

NOTE: The Vaddio ClearVIEW HD-18 Control Protocol is similar, but not identical to the Sony™

VISCA™ command set in order to be compatible with several popular control devices. Not all VISCA
commands are supported and there are many HD-18 specific commands in the following Command and
Inquiry Lists.

Pin # RJ-45 RS-232 and IR Out Pins

1) Unused

2) Unused

3) IR Out (TTL level)

4) IR Output (Diff Signal to HD-18 Quick-Connect)

5) IR Ground (Diff Signal to HD-18 Quick-Connect)

6) GND (GND of IR Short Range - Pin 3)

7) RXD (from TXD of control source)

8) TXD (to RXD of control source)

HD-18 Command List (1/2)

Command Set V Command Command Packet Comments

AddressSet Y Broadcast 88 30 01 FF Address Set

IF_Clear Y Broadcast 88 01 00 01 FF I/F Clear

CommandCancel Y 81 2p FF p: Socket No(=1 to2)

CAM_Power Y

CAM_Zoom Y

CAM_Focus Y

CAM_WB Y

CAM_RGain Y

CAM_BGain Y

CAM_AE Y

CAM_Iris Y

CAM_Gain Y

On

Y

Off

Stop

Y

Tele(Standard)

Y

Wide(Standard)

Y

Tele(Variable)

Y

Wide(Variable)

Y

Direct

Y

Direct(Variable)

Stop

Y

Far(Standard)

Y

Near(Standard)

Y

Far(Variable)

Y

Near(Variable)

Y

AutoFocus

Y

ManualFocus

Y

Auto/Manual

Auto

Y

Manual

Reset

Y

Up

Y

Down

Y

Direct

Reset

Y

Up

Y

Down

Y

Direct

Full Auto

Y

Manual
Shutter Priority

Y

Iris Priority

Y

Bright

Y

Reset

Y

Up

Y

Down

Y

Direct

Reset

Y

Up

Y

Down

Y

Direct

81 01 04 00 02 FF
81 01 04 00 03 FF

81 01 04 07 00 FF
81 01 04 07 02 FF
81 01 04 07 03 FF
81 01 04 07 2p FF
81 01 04 07 3p FF
81 01 04 47 0p 0q 0r 0s FF
81 01 7E 01 4A 0V 0p 0q 0r 0s FF

81 01 04 08 00 FF
81 01 04 08 02 FF
81 01 04 08 03 FF
81 01 04 08 2p FF
81 01 04 08 3p FF
81 01 04 38 02 FF
81 01 04 38 03 FF
81 01 04 38 10 FF

81 01 04 35 00 FF
81 01 04 35 05 FF

81 01 04 03 00 FF
81 01 04 03 02 FF
81 01 04 03 03 FF
81 01 04 43 00 0p 0q 0r FF

8x 01 04 04 00 FF
8x 01 04 04 02 FF
81 01 04 04 03 FF
81 01 04 44 00 0p 0q 0r FF

81 01 04 39 00 FF
81 01 04 39 03 FF
81 01 04 39 0A FF
81 01 04 39 0B FF
81 01 04 39 0D FF

81 01 04 0B 00 FF
81 01 04 0B 02 FF
81 01 04 0B 03 FF
81 01 04 4B 00 00 0p 0q FF

81 01 04 0C 00 FF
81 01 04 0C 02 FF
81 01 04 0C 03 FF
81 01 04 4C 00 00 0p 0q FF

Power On/Off

p:0(Slow) to 7(Fast)
p:0(Slow) to 7(Fast)
pqrs: Zoom Position*
V:(Speed) 0-7

Supported as ‘Standard’
Supported as ‘Standard’

pqr:000-1ff

pqr:000-1ff

Auto Exposure Mode
Manual Control Mode
Shutter Priority Mode
Exposure Priority Mode (default)
AGC Priority Mode

pq(0x00-0x11)

pq(0x00-0x1E)

WallVIEW HD-18 Manual 341-888 Rev. C Page 13 of 16

WallVIEW HD-18

HD-18 Command List (2/2)

Command Set V Command Command Packet Comments

CAM_Backlight Y Y On

CAM_Aperture Y

CAM_Memory Y

CAM_IDWrite Y 81 01 04 22 0p 0q 0r 0s FF pqrs:Camera ID(==0000 – FFFF)

IR_Receive Y

IR_ReceiveReturn N+

Pan-tiltDrive Y

Tally Y

Preset Pan Speed Y Pan/Tilt Speed 81 01 7E 01 0B WW VV ZZ FF WW: Pan Speed (0x01-0x18)

Motor Config Y Y Hard Motor Stops

BLK.Enhance Y Pedestal 81 01 7E 53 00 00 0p 0q FF pq: Black Level (0x01-0xFD)

GMA.Enhance Y Gamma 81 01 7E 54 00 00 0p 0q FF pq: Gamma (0x00-0x8F)

CRM.Enhance Y Chroma 81 01 7E 55 00 00 0p 0q FF pq: Chroma (0x08-0x1F)

KNE.Enhance Y Knee 81 01 7E 55 00 00 0p 0q FF pq: Knee (0x0-07F)

CAM_Shutter Y

CAM_ExpComp Y

CAM_ICR
Cut Filter

Off

Reset

Y

Up

Y

Down

Y

Direct

Reset

Y

Set

Y

Recall

On

Y

Off

Y

On/Off

On

N+

Off

Up

Y

Down

Y

Left

Y

Right

Y

UpLeft

Y

UpRight

Y

DownLeft

Y

DownRight

Y

Stop

Y

Absolute Position

Y

Home

Reset
Y
Y

On
Y

Off

Soft Motor Stops

Reset
Y

Up
Y

Down
Y

Direct

On
Y

Off
Y

Reset
Y

Up
Y

Down
Y

Direct

Y Y ICR On

ICR Off

81 01 04 33 02 FF
81 01 04 33 03 FF

81 01 04 02 00 FF
81 01 04 02 02 FF
81 01 04 02 03 FF
81 01 04 42 00 00 0p 0q FF

81 01 04 3F 00 0p FF
81 01 04 3F 01 0p FF
81 01 04 3F 02 0p FF

81 01 06 08 02 FF
81 01 06 08 03 FF
81 01 06 08 10 FF

81 01 7D 01 03 00 00 FF
81 01 7D 01 13 00 00 FF

81 01 06 01 VV WW 03 01 FF
81 01 06 01 VV WW 03 02 FF
81 01 06 01 VV WW 01 03 FF
81 01 06 01 VV WW 02 03 FF
81 01 06 01 VV WW 01 01 FF
81 01 06 01 VV WW 02 01 FF
81 01 06 01 VV WW 01 02 FF
81 01 06 01 VV WW 02 02 FF
81 01 06 01 VV WW 03 03 FF
81 01 06 02 VV WW
0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z FF
0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z FF

81 01 06 04 FF
81 01 06 05 FF

81 01 7E 01 0A 00 02 FF
81 01 7E 01 0A 00 03 FF

81 01 7E 01 70 00 00 FF
81 01 7E 01 70 00 01 FF

81 01 04 0A 00 FF
81 01 04 0A 02 FF
81 01 04 0A 03 FF
81 01 04 4A 00 00 0p 0q FF

81 01 04 3E 02 FF
81 01 04 3E 03 FF
81 01 04 0E 00 FF
81 01 04 0E02 FF
81 01 04 0E 03 FF
81 01 04 4E 00 00 0p 0q FF

81 01 04 01 02 FF
81 01 04 01 03 FF

pq(0x00-0x3F)

p:Memory No(=0-0xf)

WW: Pan Speed (0x01-0x18)
VV:Tilt Speed(0x01-0x14)

YYYY: Pan Position*
ZZZZ: Tilt Position*

VV:Tilt Speed(0x01-0x14)
ZZ:Zoom Speed(0-7);

(Only supported in Shutter
Priority Mode)

Pq: 0x00-0x0E

AutoExposure Off
AutoExpouse On

Pq: 0x00-0x1E

ICR On
ICR Off

Additional Information:

Pan Range: 8044 – 7FBC (-32,700 to +32,700)
Tilt Range: E891 – 4C2B (-5,999 to +19,499)

* Actual Pan/Tilt ranges defined in Inquiry list

WallVIEW HD-18 Manual 341-888 Rev. C Page 14 of 16

WallVIEW HD-18

HD-18 Inquiry List (1/1)

Inquiry Command V Command Command Packet Comments

CAM_PowerInq Y

CAM_ZoomPosInq Y 81 09 04 47 FF y0 50 0p 0q 0r 0s FF pqr: Zoom Position

CAM_WBModeInq Y 81 09 04 35 FF y0 50 00 FF

CAM_RGain Y 81 09 04 43 FF y0 50 00 0p 0q 0r FF pqr:000-1ff

CAM_BGain Y 81 09 04 44 FF y0 50 00 0p 0q 0r FF pqr:000-1ff

CAM_AEModeInq Y 81 09 04 39 FF y0 50 00 FF

CAM_Iris Y 81 09 04 4B FF y0 50 00 00 0p 0q FF pq(0x00-0x11)

CAM_Gain Y 81 09 04 4C FF y0 50 00 00 0p 0q FF pq(0x00-0x1E)

CAM_BacklightModeInq Y 81 09 04 33 FF y0 50 02 FF

CAM_ApertureInq Y 81 09 04 42 FF y0 50 00 00 0p 0q FF pq(0x00-0x3F)

CAM_MemoryInq Y 81 09 04 3F FF y0 50 0p FF p:Memory No(=0-0xf)

CAM_IDInq Y 81 09 04 3F FF y0 50 0p 0q 0r 0s FF pqrs:(0000 – FFFF)

CAM_ReceiveInq Y 81 09 06 08 FF y0 50 02 FF

Pan-TiltMaxSpeedInq Y 81 09 06 11 FF y0 50 WW VV FF WW: Pan Speed (0x01-0x18)

Pan-tiltPositionInq Y 81 09 06 12 FF y0 50 0Y 0Y 0Y 0Y 0Z 0Z

TallyInq Y

PresetSpeedInq Y 81 09 7E 01 0B FF y0 50 WW VV ZZ FF WW: Pan Speed (0x01-0x18)

Motor Config Y 81 09 7E 01 70 FF y0 50 00 FF

BLK.Enhance Y 81 01 7E 53 FF y0 50 00 00 0p 0q FF pq: Black Level (0x01-0xFD)

GMA.Enhance Y 81 01 7E 54 FF y0 50 00 00 0p 0q FF pq: Gamma (0x00-0x8F)

CRM.Enhance Y 81 01 7E 55 FF y0 50 00 00 0p 0q FF pq: Chroma (0x08-0x1F)

KNE.Enhance Y 81 01 7E 56 FF y0 50 00 00 0p 0q FF pq: Knee (0x0-07F)

CAM_AEModeInq Y 81 09 04 39 FF y0 50 00 FF

CAM_ShutterPosInq Y 81 09 04 4A FF y0 50 00 00 0p 0q FF pq: ShutterPosition

CAM_ExpCompModeInq Y 81 09 04 3E FF y0 50 02 FF

CAM_ExpCompPosInq Y 81 09 04 4E FF y0 50 00 00 0p 0q FF pq: ExpComp Pos -Iris Position

CAM_ICRModeInq Y 81 09 04 01 FF y0 50 02 FF

81 09 04 00 FF

81 09 7E 01 0A FF y0 50 02 FF

Y

y0 50 02 FF
y0 50 03 FF

y0 50 05 FF

y0 50 03 FF

y0 50 03 FF

y0 50 03 FF

0Z 0Z FF

y0 50 03 FF

y0 50 01 FF

y0 50 03 FF
y0 50 0A FF
y0 50 0B FF
y0 50 0D FF

y0 50 03 FF

y0 50 03 FF

On
Off(Standby)

Auto
Manual

Auto Exposure Mode
Manual Control Mode

On
Off

On
Off

VV:Tilt Speed(0x01-0x14)

YYYY: Pan (0x0100-0x1800)
ZZZZ:Tilt (0x0100-0x1400)

On
Off

VV:Tilt Speed(0x01-0x14)
ZZ:Zoom Speed(0-7);

Hard Motor Stops
Soft Motor Stops

Auto Exposure Mode
Manual Control Mode
Shutter Priority Mode
Exposure Priority Mode
AGC Priority Mode

(Only supported in Shutter
Priority Mode)

On - AE Mode Off
Off – AE Mode On

ICR On
ICR Off

WallVIEW HD-18 Manual 341-888 Rev. C Page 15 of 16

WallVIEW HD-18

Toll Free: 800-572-2011 ▪ Phone: [phone] ▪ FAX: [phone]

9433 Science Center Drive, Minneapolis, MN 55428

www.vaddio.com

©2010 Vaddio - All Rights Reserved. Reproduction in whole or in part without written permission is prohibited. Specifications and pricing are
subject to change without notice. Vaddio, ProductionVIEW, Quick-Connect, ControlVIEW, WallVIEW, EZCamera and PowerRite are
registered trademarks of Vaddio. All other trademarks are property of their respective owners. Document Number 341-888 Rev. C

WallVIEW HD-18 Manual 341-888 Rev. C Page 16 of 16