Table: ZoomSHOT 20 HD VIDEO Selections ................................................................................................... 6
Quick-Connect SR Interface ...................................................................................................................................... 7
Image: Rear Panel with Feature Call-outs ........................................................................................................ 7
First Time Set-up: ...................................................................................................................................................... 8
Step By Step Installation Instructions: ................................................................................................................... 9
General Specifications ............................................................................................................................................. 10
Vaddio IR SHOT Commander Remote ................................................................................................................... 11
Image: Vaddio IR SHOT Commander Hand-held IR remote .......................................................................... 11
Table: ZoomSHOT 20 OSD Menu Structure .......................................................................................................... 12
Compliance and CE Declaration of Conformity - ZoomSHOT 20 ........................................................................... 14
Warranty Information ............................................................................................................................................... 15
Appendix 1: Pin-outs for ZoomSHOT 20 Camera and Quick-Connect SR ............................................................ 16
Table: EZ-POWER VIDEO RJ-45 Connector Pin-outs ................................................................................... 16
Table: ZoomSHOT 20 Camera RS-232 Port .................................................................................................. 16
Table: Quick-Connect SR DE-15 Pin-Output (Analog Component YPbPr) .................................................... 16
Communication Specification .................................................................................................................................. 17
ZoomSHOT 20 Command List (1/2) ................................................................................................................. 17
ZoomSHOT 20 Command List (2/2) ................................................................................................................. 18
ZoomSHOT 20 Inquiry List (1/1) ...................................................................................................................... 19
ZoomSHOT 20 QSR System Document Number 342-0968 Rev A Page 3 of 20
Page 4
ZoomSHOT 20 QSR Camera System
V
O
VERVIEW
:
The Vaddio ZoomSHOT 20 QUSB camera system produces amazing
results for small, medium and large room applications. Anywhere that
a Point-of-View or stationary camera can be used alone or in
conjunction with a Vaddio PTZ camera, to simplify camera coverage
and preset positioning, the ZoomSHOT 20 is the answer.
Essentially, the ZoomSHOT 20 camera is a low cost pan/tilt/zoom
camera, where the pan and tilt are adjusted manually. However,
unlike fixed-lens stationary cameras, the ZoomSHOT 20 is equipped
with a 20X optical power zoom lens that produces a horizontal field of
view ranging from 63º on the wide end to 3.47º on the tele end in a HD
16:9 format.
ZoomSHOT 20 was designed from the ground up and uses the Vaddio
EZCamera™ Cat-5 wiring standard for video, power and control. The
ZoomSHOT 20 supports a wide range of HD video resolutions that are
selectable on the rear panel up to the native 1080p/60 resolution. This
camera can deliver HD video signals, power and control up to 150’
(45.72m) on Cat-5 cable.
This system features the Quick-Connect SR Interface, which was the
first HD analog video, power and control interface designed by Vaddio
or anybody else for that matter. The EZ-POWER VIDEO jack, color
coded orange, carries power to the camera and returns HSDS™ (high
speed differential) HD video over the same cat-5/5e/6 cable. The
video output of the Quick-Connect SR is clean YPbPr analog
component. The RS-232 jack, color coded blue, provides bidirectional control and IR Forwarding to and from the camera.
Choose between three (3) IR frequencies for the Vaddio IR SHOT
Commander to allow multiple cameras to be locally IR controlled with
a single remote control. And like all Vaddio camera packages, the thin
profile wall mount is included.
Intended Use:
Before operating the device, please read the entire manual thoroughly. The system was designed, built and tested
for use indoors with the power supply provided. Outdoor operation or use of a different power supply has not been
tested and could damage the device and/or create a potentially unsafe operating condition.
Important Safeguards:
Read and understand all instructions before using. Do not operate any device if it has been dropped or damaged.
In this case, a Vaddio technician must examine the product before operating. To reduce the risk of electric shock,
do not immerse in water or other liquids and avoid extremely humid conditions.
Use only the power supply provided with the system. Use of any unauthorized power
supply will void any and all warranties.
Please do not use “pass-thru” type RJ-45 connectors. These pass-thru type connectors do not work well for
professional installations and can be the cause of intermittent co nnections which can result in the RS-232
control line failing and locking up, and/or compromising the HSDS (high speed differential) signals. For b est
results please use standard RJ-45 connectors and te st all cables for proper pin-outs prior to connection to
addio product.
Save These Instructions:
The information contained in this manual will help you install and operate your product. If these instructions are
misplaced, Vaddio keeps copies of Specifications, Installation and User Guides and most pertinent product
drawings for the Vaddio product line on the Vaddio website. These documents can be downloaded from
www.vaddio.com free of charge.
ZoomSHOT 20 QSR System Document Number 342-0968 Rev A Page 4 of 20
Page 5
ZoomSHOT 20 QSR Camera System
U
NPACKING
Carefully remove the product and all of the included parts from the packaging.
ZoomSHOT 20 QSR Camera System (North America):
Part Number: 999-6920-300
One (1) ZoomSHOT 20, HD Camera (998-6920-000)
One (1) Vaddio IR Shot Commander Remote
One (1) Quick-Connect SR Interface (998-1105-016)
One (1) 24 VDC, 2.0 A Power Supply with Power Cord for North America
One (1) Thin Profile Wall Mount with Mounting Hardware
One (1) EZCamera Cat-5 Control Adapter (RJ-45-F to DB-9-F)
Quick-Start Guide
NOTE: Full manuals are downloaded from support.vaddio.com
ZoomSHOT 20 QSR Camera System (International):
Part Number: 999-6920-301
One (1) ZoomSHOT 20, HD Camera (998-6920-000)
One (1) Vaddio IR Shot Commander Remote
One (1) Quick-Connect SR Interface (998-1105-016)
One (1) 24 VDC, 2.0 A Power Supply
One (1) Euro Power Cable
One (1) UK Power Cable
One (1) Thin Profile Wall Mount with Mounting Hardware
One (1) EZCamera Control Adapter (RJ-45-F to DB-9-F)
Quick Start Guide
NOTE: Full manuals are downloaded from support.vaddio.com
ZoomSHOT 20 Front View with Feature Call-outs
Image: ZoomSHOT 20 HD PTZ Camera
1) Lens: 20X Optical Zoom Lens
2) IR Sensor and Power/Tally LED: The IR sensor for the IR SHOT Commander Remote is located here. In a
separate opening, a blue LED power light and a red LED tally resides (it turns purple on boot up too).
3) The Yoke: For manual pan and tilt. Tilt range is ± 30° and Pan is limited to the service loop of the cabling.
4) The Aluminum Base and Steel Cylindrical Body: Please don’t drop it on your foot, it’s fairly substantial.
5) Logo: Really Cool Logo Badge (RCLB). The RCLB is affixed to the base in a recessed ovoid area.
ZoomSHOT 20 QSR System Document Number 342-0968 Rev A Page 5 of 20
:
②
①
③
④
⑤
Page 6
ZoomSHOT 20 QSR Camera System
Rear Panel Connections with Callouts
Image: ZoomSHOT 20 HD Camera
①
②
③
④
1) RS-232 (Color Coded Blue): The RS-232 RJ-45 accepts modified VISCA protocol for camera control.
2) EZ-POWER VIDEO Port (Color Coded Orange): This RJ-45 connector is only used with the Quick-Connect
SR, Quick-Connect DVI-D/HDMI SR Interface, Quick-Connect USB and USB Mini Interfaces to supply power and
return HSDS (differential) video from the camera over Cat-5/5e/6 cable up to distance of 150’ (45.72m).
3) ZoomSHOT20DIP Sw itch Settings: Settings for IR remote frequency, IR receiver on/off, image flip and
defaults can be configured on these switches. See the Switch Settings page for additional information. The dip
switch settings are as follows:
Table: ZoomSHOT 20 DIP Switch Settings
DIP Switch Function
1 Up = IR1, Down = IR2
2 Up = IR 1 or 2, Down = IR3
3 Up=IR ON, Down = IR OFF
4 Up = Normal Image, Down = Image Flip
5 Not Used
6 Not Used
All Down Reset to Defaults - with power cycle
4) HD Video Select:
A rotary switch allows the user to choose the component HD output video resolution and format. After setting or
changing the resolution, reboot the camera to ensure proper operation. Simply set the rotary switch to an assigned
position to output video. The HD Video Select Rotary Switch Settings are as follows:
Table: ZoomSHOT 20 HD VIDEO Selections
Rotary
0
1 1080i/59.94 9 -2 1080p/59.94 A -3 720p/60 B -4 1080i/60 C -5 1080p/60 D -6 720p/50 E 1080p/30
7 1080i/50 F 1080p/25
Resolutions
720p/59.94 8 1080p/50
Rotary
Resolutions
Notes:
Set the rotary switch to an assigned position. If put on an unassigned position, then 720p/60 will be displayed.
Point the notch in
the switch stem to
assign the rotary
position
ZoomSHOT 20 QSR System Document Number 342-0968 Rev A Page 6 of 20
Page 7
ZoomSHOT 20 QSR Camera System
Q
UICK-CONNECT SR INTERFACE
Image: Rear Panel with Feature Call-outs
1) Power Input:
A 5.5mm OD x 2.5mm ID coaxial connector for the provided 24 VDC, 2.08 Amp power supply.
2) EZ-POWER VIDEO Port (Color Coded Orange):
A single Cat-5 connection between the EZCAMERA POWER & HD VIDEO RJ-45 connector and the camera’s EZ
Power HD Video Port on the HD-20 camera extends power and video. Power is fed to the camera and HSDS
video is returned from the camera on the same Cat-5.
3) HD Video Output:
DE-15 connector outputs the YPbPr analog component HD video, which was extended from the camera over Cat5 cable. SD video resolutions (Y/C and CVBS formats) are not supported by the Quick-Connect SR Interface,
however analog component SD video is supported.
4) IR Output:
With the IR pass-thru turned ON (see camera dip switch settings), IR from third-party IR remote controls can be
sent through the ZoomSHOT camera to third-party equipment, such as hardware videoconferencing codecs. IR
can be used as either modulated (through the air) or non-modulated (wired) signals.
5) RS-232 INPUT (Color Coded Grey) & RS-232 OUT TO CAMERA Jacks:
These RJ-45 connectors allow an external controller (beware of upcoming shameless plug) like the
ProductionVIEW™ Precision Camera Controller to route through the Quick-Connect SR for ease of cabling.
①
②
③
④
⑤
ZoomSHOT 20 QSR System Document Number 342-0968 Rev A Page 7 of 20
Page 8
ZoomSHOT 20 QSR Camera System
(
)
(
)
Image: Basic Wiring Configuration
ZoomSHOT 20 HD POV Camera with Quick-Connect SR Interface (color coded connectors) and ProductionVIEW
Precision Camera Controller.
ZoomSHOT 20
Two Cat-5/5e/6 Cables
Up to 150’ (45.72m)
RS-232 Cat-5
blue to blue
EZ-POWER VIDEO Cat-5
< Power to Camera - HD Video to QC SR >
orange to orange
Quick-Connect SR Interface
(Rear Panel View)
24VDC, 2.08 Amp
Power Supply
Analog Component YPbPr
RS-232
Cat-5
ProductionVIEW Precision Camera Controller
F
IRST TIME SET-UP
HD Monitor
(Simulated HD Video Feed)
:
The ZoomSHOT 20 was designed to be very easy to use and operate. There is documentation at the back of this
manual for pin-outs of the connectors on the Quick-Connect and camera.
Before Installing:
Choose camera mounting location, paying close attention to camera viewing angles, lighting conditions,
possible line of site obstructions, and checking for in-wall obstructions where the camera is to be mounted.
Always pick a mounting location that will optimize the performance of the camera. Please locate the camera to
enable easy positioning of the camera body with the ability to point down and away from the ceiling and a pile
of fluorescent lighting cells. Cameras generally don’t like to be swamped with fluorescent light and nobody sits on the ceiling anyway.
The Thin Profile Wall Mount for the ZoomSHOT 20 can be mounted directly to a 1-gang wall box or can be
mounted using only dry wall anchors.
For Power/Video and RS-232 signals, use standard Cat-5 cable (568B termination and real RJ-45 connectors)
from the EZ-POWER VIDEO and RS-232 ports on the back of the ZoomSHOT to the Quick-Connect SR
Interface. These jacks are color coded for ease of connection.
ZoomSHOT 20 QSR System Document Number 342-0968 Rev A Page 8 of 20
Page 9
ZoomSHOT 20 QSR Camera System
Step By Step Installation Instructions:
Step 1: After determining the optimum location of the camera, route, mark and
test the two (2) Cat-5 cables from the camera to the Quick-Connect SR Interface
located at the head-end. The two Cat-5e cables should feed-through the hole
located on the rear flange of the Thin Profile Wall Mount. If the bracket is to be
mounted on a 1-gang wall box, use the screws supplied with the wall box cover
plate to attach the Thin Profile Wall Mount. If mounting to the drywall with wall
anchors, use two (2) quality wall anchors. The mounting holes are slotted and are
90° opposing to provide easy leveling. Level the mount and tighten the mounting
screws.
Step 2:
Using the HD VIDEO SELECT rotary switch and CAMERA SETTINGS dip switches on the back of the camera, set
up the camera’s output resolution and functional preferences. There are tables on previous pages that identify the
choices…maybe keep these tables handy for future use…or you can easily look them up on the Vaddio website
(vaddio.com) when needed.
On the camera:
Set the desired HD Resolution with the rotary selection switch.
Set the IR frequency of the camera (if it is to respond to the IR remote control).
Set the image orientation (normal or flipped).
Step: 3: Follow the sample wiring diagram for connecting the Cat-5 cables to the ZoomSHOT 20 and Quick-
Connect SR Interface (yep, on the next page, but read and understand the rest of these instructions especially the
next note).
NOTE: Check all Cat-5e cables for continuity in advance of the final connection. Label the
Cat-5e cables. Plugging the EZ-POWER VIDEO cable into the wrong RJ-45 may cause
damage to the camera system and void the warranty. For premise cabling, please use real
RJ-45 connectors and crimpers. Please don’t use the pull through or EZ-type RJ-45s.
Step 4: Place the camera onto the camera mount and use the provided ¼”-20 screws to secure the camera to the
mount. To dress the cabling, push the extra cable back into the wall opening.
Step 5: Connect the Vaddio 24 VDC, 2.08 Amp power supply to a power outlet and to the Quick Connect SR
Interface. Power will travel down the EZ-POWER VIDEO Cat. 5 cable to the camera. The camera will boot up and
in a few seconds, HSDS (differential) video will travel back down the Cat-5 cable and be ready to accept control
information from the IR remote control or RS-232 camera controller.
To insure proper continuity of control and operation of the cameras, the RS-232 controller (control
system or joystick) should be powered on after the camera.
ZoomSHOT 20 QSR System Document Number 342-0968 Rev A Page 9 of 20
Page 10
ZoomSHOT 20 QSR Camera System
GENERAL SPECIFICATIONS
ZoomSHOT 20 QSR System
Part Numbers ZoomSHOT 20 QSR System 999-6920-300 (North America)
ZoomSHOT 20 Camera
Image Sensor 1/2.8-Type Exmor CMOS Image Sensor
Total/Effective Pixels 2.38 Million Total Pixels, 2.14 Million Effective pixels
Video Output Resolutions HD: 1080/59.94/50/30/25, 1080i/59.94/50, 720p/59.94/50, 16:9 Aspect Ratio
Lens/ Focal Length 20X Optical Zoom, F=4.44mm wide end to 89mm tele end (F1.6 - F3.4),
Horizontal Viewing Angle
Video S/N Ratio >52 dB
Minimum Illumination Color: 0.3 Lux (F1.6, 1/30 sec, 50 IRE), B/W: 0.03 Lux (F1.6, 1/30 sec, 50 IRE)
Serial Control Protocol RS-232 (Modified VISCA)
Manual Pan/Tilt Range Pan: Limited to service loop of cabling, yoke and base are mechanical only
Preset Positions Six (6) Programmed and Recalled via IR Remote, 16 Programmed and Recalled with RS-232
Tally Light Available through RS-232 Control
Camera Connectors Two (2) RJ-45 Jacks:
HD Video Select 16-Position Rotary Switch: Used to set the ZoomSHOT 20 HD Video Resolution Output
Camera Settings 6-Position Dip Switch: For IR Frequency, IR ON/OFF and Image Flip
Thin Profile Wall Mount 535-2000-237 (Provided with camera)
User Controls IR Shot Commander Remote with OSD for camera set-up, RS-232
Materials & Weight Aluminum & Steel, Weight = 2.75643 lbs. (1.68kg)
Dimensions: Tube: 3” ( 76.2mm) Diameter x 4.75” (120.65mm) Long
Quick-Connect SR Interface
Connectors
Power Supply 24 VDC, 2.0 Amp
Dimensions (H x W x D) 1/3 Rack Size - 1.6” (40.64mm ) H x 5.5” (139.7mm) W x 3.25” (82.55mm) D
Weight 0.45 lbs. ( 0.2041165643 kg)
Accessory Rack Mount Adapter: 998-6000-002 - Holds three (3) Quick-Connect SR Interfaces
ZoomSHOT 20 QSR System Document Number 342-0968 Rev A Page 10 of 20
ZoomSHOT 20 QSR System 999-6920-301 (International)
Min. Focus Distance 1.5m
Horizontal: 63º Wide End to 3.47º Tele End, (16:9 Aspect Ratio)
Tilt: ± 30°, Invertible for Ceiling Mount
EZ-POWER VIDEO RJ-45 Jack for use with Quick-Connect - Supplies power to the camera and
returns differential HD video from the camera
RS-232 RJ-45 Jack (RS-232 Communication)
Black powder coating, Sized to fit on 1-gang wall box or drywall, mounting hardware included
Power Connector: 5.5mm OD, 2.5mm ID coaxial connector
Power/Video RJ-45: Supplies power to, and differential HD video from the camera
Video Output: DE-15 connector for HD Analog Component (YPbPr) video only (No SD Support)
IR Output: Transmits modulated or non-modulated IR signals received from the camera’s IR
receiver
RS-232 IN RJ-45: Accepts RS-232 from ProductionVIEW or other external control systems
RS-232 OUT RJ-45: Sends RS-232 from Quick-Connect SR to the camera
Page 11
ZoomSHOT 20 QSR Camera System
V
ADDIO IR
SHOT C
OMMANDER REMOTE
Spatially Efficient IR Remote Controller for ZoomSHOT™ 20 and WideSHOT™ Camera Systems
The Vaddio IR SHOT Commander was designed to work with the Vaddio ZoomSHOT and WideSHOT camera
systems and is compatible with the PowerVIEW™, ClearVIEW™ cameras The Vaddio IR SHOT Commander is
compatible with the following Vaddio camera packages:
ZoomSHOT 20 and WideSHOT Camera Systems (shipped with these products)
SE
Vaddio ClearVIEW HD-20
, PowerVIEW HD-22 and HD-30
The Vaddio IR Shot Commander is also compatible with the Sony® EVI series and the BRC series PTZ cameras.
Image: Vaddio IR SHOT Commander Hand-held IR remote
(Top View)
ZOOM OUT ZOOM I
P-STORE IR 1
Red LED indicates IR transmission and
the brightness indicates battery strength
OSD - On Screen
Display Menu
PRESET 1
Power On/Off
Camera Standby
Arrow Keys X 4
Pan Left, Pan Right,
Tilt Up, Tilt Down
Menu Navigation
OK, Enter, Select and
Camera Home
Zoom Camera OUT (wide)
Zoom Camera IN (telephoto)
Preset Button - Setting Presets
Move the camera into position
Push and hold P-STORE button
Touch buttons 1 or 2 to set Preset
Recalls ZoomSHOT Preset 1
or Preset 2 (zoom position)
*WideSHOT uses a manual lens
Select IR Frequencies (3)
Allows up to 3 cameras to
be controlled in a room with
one (1) IR Remote
Note: Camera dip switches
set IR frequency.
Quick Specs
IR Range 20’ to 30’ (6m to 9m)
Batteries 2 x AAA (Batteries not
Keys (buttons) 15 Silicone Rubber Keys
Dimensions
L x W x H
LED Indicator Red LED Illuminates when
Compatible
Cameras
ZoomSHOT 20 QSR System Document Number 342-0968 Rev A Page 11 of 20
shipped with 998-2101-001)
4.53” (115mm) x 1.57”
(40mm) x 1.1” (28mm)
transmitting IR, Brightness
indicates battery strength
Ships with ZoomSHOT and
WideSHOT. Compatible with
all Vaddio ClearVIEW,,
PowerVIEW cameras (limited
function set) and most Sony
BRC & EVI cameras.
Page 12
ZoomSHOT 20 QSR Camera System
TABLE:ZOOMSHOT20OSDMENU STRUCTURE
Use this OSD menu with the IR SHOT Commander to make video adjustments (AWB, COLOR, EXP, etc…) on the HD-20SE
Camera.
Menu Controls Modes/Range Default Notes
SSDR OFF OFF Dynamic Range Adjustment
ON SSDR 0-15 8* *When Dynamic Range is ON
Return Return to Main Menu
WHITE BAL ATW ON Auto White Balance - ON
MANUAL> RED 0 - 1000 560 Adjust Red Level
BLUE 0 - 1000 480 Adjust Blue Level
RETURN< Return to WHITE BAL Menu
AWC-SET OUTDOOR Set to Outdoor when room has direct sun light and blue walls INDOOR Set to Indoor when fluorescent lights start to cause color variation in ATW mode MERCURY SODIUM RETURN< Return to Main Menu
BACKLIGHT OFF OFF Default BLC is off
WDR> LEVEL (LOW / MED / HIGH) OFF Wide Dynamic Range
RETURN< BLC> LEVEL (LOW / MED / HIGH) OFF BOTTOM 1-100 LEFT 1-100 RIGHT 1-100 RETURN< Return to BACKLIGHT Menu
HLC> LEVEL (LOW / MED / HIGH) OFF MASK TONE 1-15 RETURN< Return to BACKLIGHT Menu
RETURN< Return to Main Menu
INTELLIGENCE OFF Intelligence, motion detection analytics and masking are not processed or used by the
FOCUS MODE AUTO / MANUAL / ONE PUSH AUTO ZOOM TRACK> OFF / TRACK / AUTO TRACK AUTOTRACK ZOOM SPEED> SLOW / MEDIUM / FAST DIGITAL ZOOM> OFF/ON OFF Default is OFF
ON>LIMIT X2 - X16 Avoid Digital Zoom if possible
RETURN< Return to FOCUS Menu
Zoom POS INIT> OFF/AUTO Zoom position initialization
MANUAL> POS INIT 1X - 20X 1X Sets INIT Zoom Position
RETURN< Return to FOCUS Menu
USER PRESET> OFF/ON OFF ON > PRESET NO 1-128 1 Zoom Presets
PRESET SAVE PRESET CLEAR RETURN< Return to FOCUS Menu
LENS INIT MANUAL / AUTO RETURN< Return to Main Menu
EXPOSURE BRIGHTNESS 0-100 50 Brightness Sets Luminance Target IRIS> AUTO AUTO Automatic Gain Control
MANUAL> Closed to F28 Manual Iris
RETURN< Return to EXPOSURE Menu
SHUTTER A FLK Use Anti-Flicker when lighting causes color huntingESC MANUAL> 1/30 - 1/30,000 sec. Shutter Speed
RETURN< Return to EXPOSURE Menu
AGC OFF / LOW /MED / HIGH LOW MANUAL (OFF)> AGC VALUE 0 - 36dB 0 dB Automatic Gain Control
RETURN< SSNR OFF / LOW /MED / HIGH LOW Noise Reduction - Don’t use above Low
SENS-UP OFF OFF OFF - Do not Use
RETURN< Return to Main Menu
ZoomSHOT 20 QSR System Document Number 342-0968 Rev A Page 12 of 20
camera, however the OSD menu still works.
Page 13
ZoomSHOT 20 QSR Camera System
ZoomSHOT 20 OSD Menu Structure (continued)
Menu Controls Range/Modes Default Notes
SPECIAL DAY/NIGHT> COLOR / B/W / AUTO COLOR Do not use
DIS> OFF / ON OFF Digital Image Stabilization - leave off DEFOG OFF / ON / MANUAL/AUTO OFF Do not use
COMM AD JUST > BAUD RATE NEVER CHANGE THE BAUD RATE OR THE UART
UART
RETURN< Return to SPECIAL Menu
IMAGE ADJUST> H-REV ON / OFF OFF Use Dip Switch on Camera to Flip Image
V-REV ON / OFF OFF Use Dip Switch on Camera to Flip Image
SHARPNESS ON/OFF ON Picture Detail
ON> 0-30 15 RETURN< Return to IMAGE ADJUST Menu
MONITOR LCD> GAMMA .0 -1.0 0.50 COLOR LEVEL 0-100 50 RETURN< Return to IMAGE ADJUST Menu
USER> GAMMA .0 - 1.0 0.50 COLOR LEVEL 0-100 50 RETURN< Return to IMAGE ADJUST Menu
RETURN< Return to Main Menu
DISPLAY CAM TITLE ON / OFF OFF ON> A-Z, 1-9 RETURN< Return to DISPLAY Menu
CAM ID ON / OFF OFF CAM INFO ON / OFF OFF ZOOM MAG ON/OFF OFF OSD COLOR WHITE WHITE/YELLOW/GREEN/RED/BLUE
LANGUAGE
SET LANGUAGE
RETURN< Return to Main Menu
VIDEO OUT FORM COMPONENT ON / OFF ON Do not change this parameter
RETURN< Do not change resolutions here - Use the
RESET
EXIT
SETTINGS - Control is lost if these are changed.
Factory default reboot will be required.
ENGLISH (ENG, FR, KOR, SP, CHIN, JAP, PORT,
RUS, DUT, ITAL)
Rotary Switch on the back of the camera
ZoomSHOT 20 QSR System Document Number 342-0968 Rev A Page 13 of 20
Page 14
ZoomSHOT 20 QSR Camera System
C
OMPLIANCE AND CE DECLARATION OF CONFORMITY - ZOOM
Compliance testing was performed to the following regulations:
FCC Part 15 (15.107, 15.109), Subpart B Class A
ICES-003, Issue 4: 2004 Class A
EN 55022:2010 Class A
KN22 2008 (CISPR 22: 2006) Class A
KN24 2008 (CISPR 24: 1997 + A1: 2000 + A2: 2002) Class A
EMC Directive 2004/108/EC Class A
EN 55024: A2: 2003
Class A
SHOT 20
FCC Part 15 Compliance
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15, Subpart
B, of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his/her own expense.
Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept
any interference including interference that may cause undesired operation of the device.
Changes or modifications not expressly approved by Vaddio can affect emission compliance and could void the user’s authority
to operate this equipment.
ICES-003 Compliance
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio
Interference Regulations of the Canadian Department of Communications.
Le présent appareil numérique n’emet pas de bruits radioélectriques dépassant les limites applicables aux appareils numeriques
de la classe A préscrites dans le Règlement sur le brouillage radioélectrique édicte par le ministère des Communications du
Canada.
European Compliance
This product has been evaluated for Electromagnetic Compatibility under the EMC Directive for Emissions and
Immunity and meets the requirements for a Class A digital device. In a domestic environment this product may
cause radio interference in which case the user may be required to take adequate measures.
Standard(s) To Which Conformity Is Declared:
EMC Directive 2004/108/EC
EN 55022:2010
EN 55024: A2: 2003
EN 61000-4-2: 1995 + Amendments A1: 1998 + A2: 2001 Electrostatic Discharge
EN 61000-4-3: 2006 + A1: 2008 Radiated Immunity
EN 61000-4-4: 2004 + Corrigendum 2006 Electrical Fast Transients
EN 61000-4-5: 2006 Surge Immunity
EN 61000-4-6: 2009 Conducted Immunity
EN 61000-4-8: 2010 Power Frequency Magnetic Field
EN 61000-4-11: 2004 Voltage Dips, Interrupts and Fluctuations
KN24 2008 (CISPR 24: 1997 + A1: 2000 + A2: 2002)
EN 61000-4-2 Electrostatic Discharge
EN 61000-4-3 Radiated Immunity
EN 61000-4-4 Electrical Fast Transients
EN 61000-4-5 Surge Immunity
EN 61000-4-6 Conducted Immunity
EN 61000-4-8 Power Frequency Magnetic Field
EN 61000-4-11 Voltage Dips, Interrupts and Fluctuations
IEC 60950-1:2005 (2nd Edition); Am 1:2009
EN 60950-1:2006+A11:2009+A1:2010+A12:2011
Safety
Safety
Class A
Immunity
IT Immunity Characteristics
ZoomSHOT 20 QSR System Document Number 342-0968 Rev A Page 14 of 20
Page 15
ZoomSHOT 20 QSR Camera System
WARRANTY INFORMATION
(See Vaddio Warranty, Service and Return Policies posted on vaddio.com for complete details):
Hardware* Warranty: Two (2) year limited warranty on all parts and labor for Vaddio manufactured products. Vaddio warrants
its manufactured products against defects in materials and workmanship for a period of two years from the day of purchase, to
the original purchaser, if Vaddio receives notice of such defects during the warranty. Vaddio, at its option, will repair or replace
products that prove to be defective. Vaddio manufactures its hardware products from parts and components that are new or
equivalent to new in accordance with industry standard practices.
Exclusions: The above warranty shall not apply to defects resulting from improper or inadequate maintenance by the customer,
customers applied software or interfacing, unauthorized modifications or misuse, mishandling, operation outside the normal
environmental specifications for the product, use of the incorrect power supply, modified power supply or improper site operation
and maintenance. OEM products and products manufactured by other companies are excluded and are covered by the
manufacturer’s warranty.
Vaddio Customer Service: Vaddio will test, repair, or replace the product or products without charge if the unit is under
warranty. If the product is out of warranty, Vaddio will test then repair the product or products. The cost of parts and labor
charge will be estimated by a technician and confirmed by the customer prior to repair. All components must be returned for
testing as a complete unit. Vaddio will not accept responsibility for shipment after it has left the premises.
Vaddio Technical Support: Vaddio technicians will determine and discuss with the customer the criteria for repair costs and/or
replacement. Vaddio Technical Support can be contacted through one of the following resources: e-mail support at
support@vaddio.com or online at vaddio.com.
Return Material Authorization (RMA) Number: Before returning a product for repair or replacement request an RMA from
Vaddio’s technical support. Provide the technician with a return phone number, e-mail address, shipping address, product serial
numbers and original purchase order number. Describe the reason for repairs or returns as well as the date of purchase. See
the General RMA Terms and Procedures section for more information. RMA’s are valid for 30 days and will be issued to Vaddio
dealers only. End users must return products through Vaddio dealers. Include the assigned RMA number in all correspondence
with Vaddio. Write the assigned RMA number clearly on the shipping label of the box when returning the product. All products
returned for credit are subject to a restocking charge without exception.
Voided Warranty: The warranty does not apply if the original serial number has been removed or if the product has been
disassembled or damaged through misuse, accident, modifications, use of incorrect power supply, use of a modified power
supply or unauthorized repair.
Shipping and Handling: Vaddio will not pay for inbound shipping transportation or insurance charges or accept any
responsibility for laws and ordinances from inbound transit. Vaddio will pay for outbound shipping, transportation, and insurance
charges for all items under warranty but will not assume responsibility for loss and/or damage by the outbound freight carrier.
If the return shipment appears damaged, retain the original boxes and packing material for inspection by the carrier. Contact
your carrier immediately.
Products not under Warranty: Payment arrangements are required before outbound shipment for all out of warranty products.
Other General Information:
Care and Cleaning
Do not attempt to take this product apart at any time. There are no user-serviceable components inside.
Do not spill liquids in the product
Keep this device away from food and liquid
For smears or smudges on the product, wipe with a clean, soft cloth
Use a lens cleaner on the lens - really, only use a lens cleaner
Do not use any abrasive chemicals.
Operating and Storage Conditions:
Do not store or operate the device under the following conditions:
Temperatures above 40°C (104°F) or temperatures below 0°C (32°F)
High humidity, condensing or wet environments
In inclement weather
In swimming pools or salmon farms
Dry environments with an excess of static discharge
In outer space (mostly gamma ray issues)
Under severe vibration
ZoomSHOT 20 QSR System Document Number 342-0968 Rev A Page 15 of 20
Page 16
ZoomSHOT 20 QSR Camera System
APPENDIX 1:PIN-OUTS FOR ZOOMSHOT20CAMERA AND QUICK-CONNECT SR
Important Note: The EZ-POWER VIDEO RJ-45 Connector on a Vaddio CAT-5 system
camera is for use with the Quick-Connect SR, Quick-Connect DVI/HDMI SR, QuickConnect USB and USB Mini Interfaces ONLY (568B Wiring Standard). The video signals
are differential (HSDS) and can only be processed by the interfaces above.
Table: ZoomSHOT 20 Camera RS-232 Port
Pin # Function
Pin - 1 N/A
Pin - 2 N/A
Pin - 3 N/A
Pin - 4 Not Used with QC-USB
Pin - 5 Not Used with QC-USB
Pin - 6 Digital GND
Pin - 7 RXD (from TXD of control source)
Pin - 8 TXD (to RXD of control source)
RS-232
12345678
Table: Quick-Connect SR DE-15 Pin-Output (Analog Component YPbPr)
Pin YPbPr
1 Pr
2 Y
3 Pb
4 5 6 Pr GND
7 Y GND
8 Pb GND
9 10 GND
11 12 13 14 15 -
ZoomSHOT 20 QSR System Document Number 342-0968 Rev A Page 16 of 20
Page 17
ZoomSHOT 20 QSR Camera System
COMMUNICATION SPECIFICATION
Communication Speed: 9600 bps (default)
Start bit: 1
Stop bit: 1
Data bits: 8
Parity: None
No Flow control
12345678
Pin # RJ-45 RS-232 and IR Out Pins
1) Unused
2) Unused
3) Unused
4) IR Output (Diff Signal to Quick-Connect SR)
5) IR Ground (Diff Signal to Quick-Connect SR)
6) GND (GND of IR Short Range - Pin 3)
7) RXD (from TXD of control source)
8) TXD (to RXD of control source)
NOTE: The Vaddio ZoomSHOT 20 Control Protocol is similar, but not identical to, the Sony® VISCA™ command
set in order to be compatible with several popular control devices. Not all VISCA commands are supported and
there are many HD-Series specific commands in the following Command and Inquiry Lists.
ZoomSHOT 20 Command List (1/2)
Command Set Command Command Packet Comments
Address Set Broadcast 88 30 01 FF Address Set (Daisy chain)
IF_Clear Broadcast 88 01 00 01 FF IF Clear
Command Cancel 8x 2p FF p:socket number(1,2)
CAM_Power On
Off(Standby)
CAM_Zoom Stop
Tele(Standard)
Wide(Standard)
Tele(Variable)
Wide(Variable)
Direct
Direct(Variable)
CAM_Focus Stop
Far(Standard)
Near(Standard)
Far(Variable)
Near(Variable)
AutoFocus
ManualFocus
Auto/Manual
Direct
Manual Control Mode
Shutter Priority Mode
Exposure Priority Mode (default)
pq(0x00-0x08)
pq(0x00-0x2A)
pq(0x01-0x64)
ZoomSHOT 20 QSR System Document Number 342-0968 Rev A Page 17 of 20
Page 18
ZoomSHOT 20 QSR Camera System
ZoomSHOT 20 Command List (2/2)
Command Set Command Command Packet Comments
CAM_Backlight On
CAM_Aperture Reset
CAM_Memory Reset
CAM_IDWrite 8x 01 04 22 0p 0q 0r 0s FF pqrs:0x0000 – 0xFFFF
CAM_LR_Reverse On On
IR_Receive## On
Tally On
BLK.Enhance Pedestal No Support No Support
GMA.Enhance Gamma 8x 01 7E 54 00 00 0p 0q FF pq: Gamma (0x00-0x10)
CRM.Enhance Chroma 8x 01 7E 55 00 00 0p 0q FF pq: Chroma (0x00-0x64)
KNE.Enhance Knee No Support No Support
DIS.Enhance Digital Image
SNR.Enhance Super Noise
AGC.Enhance AGC Mode 8x 01 7E 59 00 FF
CAM_Shutter Reset
CAM_ExpComp On
CAM_ICR
Cut Filter
Off
Up
Down
Direct
Set
Recall
Off
Off
On/Off
Off
Stabilizer
Reduction
Up
Down
Direct
Off
Reset
Up
Down
Direct
ICR On
ICR Off
*Zoom and Focus Data:
CAM_Zoom: Range(0x000–0x071A)
CAM_Focus: Range (0x0ed-0x0944) dependent on Zoom Position