VADDIO 999-5441-000, 999-5441-001 Installation And User Manual

Installation and User Guide

V

AADDDDIIO

V

O

™

™

S

QQUUIIGGGGLLEE

S

“Make Any Whiteboard into a Video Whiteboard”

Model Numbers:
999-5441-000: North America
999-5441-001: International

-

V

-

IIDDEEOO

V

W

HHIITTEEBBOOAARRDD

W

K

K

T

IIT

©2011 Vaddio - All Rights Reserved. Squiggle - Video Whiteboard Kit - Document Number 342-0172 Rev. B

Squiggle Video Whiteboard Kit

Inside Front Cover (blank)

Squiggle Manual 342-0172 Rev. B Page 2 of 16

Squiggle Video Whiteboard Kit

p

Squiggle Overview:

With Squiggle, your whiteboard notes are now available for the world
to see. Installed alongside just about any existing whiteboard, the
Squiggle converts your whiteboard notes into an HD or SD video
signal that can be connected to any live video input device, such as
a videoconferencing system, video mixer or even an HD video
recording system. This same video content can also be captured
with the One-Touch Image Save Button which saves the whiteboard
video image to a USB flash drive as a JPEG file.

The Squiggle is based on the same revolutionary concept of the
Squiggle Board video whiteboard system and uses the same patent
pending technology including the Squiggle Quick-Connect™,
ultrasonic pen sleeves, Cat-5e USB/power extension (up to
100’/30.5m) and Digital Control Panel with IR & ultrasonic sensors.

The Squiggle is a breeze to install and calibrate with the EZTub™
enclosure. Simply center the EZTub enclosure with the left side of
the whiteboard, fasten two (2) screws into the EZTub and snap the
Digital Control Panel into the tub. From there, a single Cat-5e cable
is run from the EZTub to the Squiggle Quick-Connect Interface at the
head-end and then into a video device. A six (6) point calibration
system is used for quick and easy set-up.

The Squiggle Quick-Connect Interface captures the data as it is drawn with the digital marker in real-time sent
from the Digital Control Panel’s pen sensors and outputs high definition DVI-D (HDMI with cable adapter) and
high definition YPbPr analog component video simultaneously at resolutions of 720p/59.94 or 720p/50Hz. The
Quick-Connect can also be switched to standard definition (480i/NTSC and 576i/PAL) instead of HD.

Made in the USA, the Squiggle simply makes any whiteboard into a video whiteboard and further redefines the
concept of the electronic whiteboard for presentation, videoconferencing, distance learning, media retrieval and
on-line curriculum applications world-wide.

Intended Use:

Before operating the device, please read the entire manual thoroughly. The system was designed, built and
tested for use indoors, and with the provided power supply and cabling. The use of a power supply other than the
one provided or outdoor operation has not been tested and could damage the camera and/or create a potentially
unsafe operating condition.

Important Safeguards:

Read and understand all instructions before using. Do not operate any device if it has been dropped or damaged.
In this case, a Vaddio technician must examine the product before operating. To reduce the risk of electric shock,
do not immerse in water or other liquids and avoid extremely humid conditions.

Use only the power supply provided with the system. Use of any unauthorized

power supply will void any and all warranties.

Please do not use “pass-thru” type RJ-45 connectors. These pass-thru type connectors do not
work well for professional installations and can be the cause of intermittent connections which
can result in the RS-232 control line failing and locking up, and/or compromising the HSDS™
signals. For best results please use standard RJ-45 connectors and test all cables for proper

in-outs prior to use and connection to Vaddio product.

Save These Instructions:

The information contained in this manual will help you install and operate your product. If these instructions are
misplaced, Vaddio keeps copies of Specifications, Installation and User Guides and product drawings for the
product line on the Vaddio website. These documents can be downloaded from www.vaddio.com

Squiggle’s Digital Control Panel, EZTub
Enclosure and Wall Spacers (mounted to the
left side and center of existing white board)

free of charge.

Squiggle Manual 342-0172 Rev. B Page 3 of 16

Squiggle Video Whiteboard Kit

Unpacking:

Carefully remove the Squiggle device and all of the parts from the packaging and identify the following parts:

• One (1) Digital Control Panel (and digital control panel removal tool)

• One (1) EZTub Enclosure

• Three (3) Wall Spacers for the EZTub Height Adjustment

• One (1) Squiggle Quick-Connect Interface

• One (1) Black Digital Marker Sleeve

• One (1) Black Marker

• One (1) Digital Eraser

• Four (4) CR2032 Batteries - two (2) for the Digital Marker Sleeve and two (2) for Digital Eraser

• One (1) Black Bullet Nose Marker

• One (1) PowerRite 12 VDC, 3.0 Amp Power Supply

• One (1) AC Cord Set for North America (International kits packed with Euro and UK Power Cables)

• Hardware Mounting Kit (Two each of #6 x 1.75 Pan Head Screws Spiral Wall Anchors)

• Documentation

The Digital Control Panel in the EZTub:

The basic system controls on the Digital Control Panel are as follows:

1) Ultra Sonic Sensors (top & bottom):
The ultrasonic sensors (top and bottom) detect the Digital
Marker Sleeve and pen movements on the Whiteboard.

2) One-Touch Image Save Button:
When a flash drive is plugged into the front panel of the
Squiggle Quick-Connect Interface, pressing this button will
save a copy of what has been drawn on the whiteboard as a
1280x720 JPEG image.

3) Erase Button:
To erase all content on the whiteboard video output, simply
press this button. Pressing this button a second time will
recall all video content written on the board from the last time
it was erased, as long as no other pen strokes are recorded.

4) Calibrate Button:
This button allows the user to calibrate the writing area of the
whiteboard.

5) Power Indicator & IR Sensor:
The ring is illuminated when the device is powered on. The
sensor detects IR emitted from the marker sleeve, and
triangulates the marker movements with the ultrasonic
sensors.

6) Pen Width:
The line thickness is adjustable in three (3) line widths (thin,
medium and thick). Line widths can be mixed on any drawing
being displayed on the video output.

7) EZTub Enclosure:

The EZTub enclosure houses the Digital Control Panel.
There is a small PCBA inside the EZTub that terminates the
Digital Control Panel and extends power and data from the
whiteboard to the Squiggle Quick-Connect Interface.

8) Wall Spacers (far right):

The system is equipped with three (3) 1/4” thick wall
spacers which are used to mount the EZTub and Digital
Control Panel as close as possible to coincident with the
whiteboard surface. Some whiteboards may only need
one spacer, some may need all three.

①
②

③

④

⑤

⑥

⑦

Digital Control Panel

in EZTub

⑧

¼” Thick Wall

Spacer

Squiggle Manual 342-0172 Rev. B Page 4 of 16

Squiggle Video Whiteboard Kit

Squiggle Quick-Connect Interface Front Panel (left to right):

1) USB Drive Port: The USB port on the front panel allows the user to plug in any standard FAT32 or Fat16

USB drive to store content written on the whiteboard. Simply press the One-TOUCH Image Save icon on the
Digital Control Panel (see previous page) and the content written on the whiteboard will be saved to the USB
drive. A confirmation of the saved content will be displayed on the video output. All information is saved as a
1280 x 720 JPEG image.

2) Power Indicator / System Reset Button: When the Quick-Connect is turned on, the POWER indicator light
illuminates. It is not a power switch. This button also serves as a SYSTEM RESET button. Pressing the
button will reset the system from boot up.

Rear Panel Connections and Controls (Left to Right):

1) Power Supply Input: 12VDC, 3.0 Amp power supply on a 5.5mm OD x 2.5mm ID connector.

2) Whiteboard RJ-45: Power and data transmitted to and from the video whiteboard via Cat. 5e cabling.

3) Ethernet on RJ-45: Ethernet port is reserved for future use and not active at this time.

4) Settings: The Quick-Connect has a 5-position dip switch for setting HD or SD resolution, refresh rate,

test bars and switches available for future settings.

5) Video Outputs: Three video outputs; DVI-D, YPbPr HD and CVBS (composite), are available on the

Squiggle Quick-Connect Interface.

• The DVI-D and YPbPr outputs are simultaneous outputs and are at a resolution of 720p/59.94 or
720p/50 which allows the Squiggle Board to be connected to a variety of video devices such as
Vaddio switchers/mixers, videoconferencing codecs, monitors and other third-party video devices.

• The SD video can be chosen instead of the HD DVI-D and YPbPr outputs and output SD resolutions
of 480i/NTSC and 576i/PAL.

NOTE: If the SD composite video output is chosen instead of the HD outputs, a dip switch setting is

changed to allow the SD output to be active. The HD outputs are not active when the SD video is
chosen with the dip switch. Conversely, the SD video out is not active when the HD video is chosen.

Optional Accessories for Squiggle:

Colored Digital Sleeves

(998-5440-030)

①

②

③

Standard Whiteboard

Eraser

(998-5440-010)

④

①

Whiteboard Cleaner

(998-5440-020)

②

⑤

Replacement Bullet

Tip Markers

(998-5440-040)

Squiggle Manual 342-0172 Rev. B Page 5 of 16

Squiggle Video Whiteboard Kit

Installation Step by Step:

Before Installing:

• Keep other IR or ultrasonic devices and reflective surfaces away from the whiteboard location.

• Since Squiggle is being installed next to an existing whiteboard, pull out the tape measure and prepare to

measure precise positions for the location of the EZTub and Digital Control Panel. Typically, the Squiggle
Quick-Connect Interface is located at the head-end, so we’ll make that assumption here too.

Step 1:

Measure the existing whiteboard. Squiggle is always
mounted on the left side and center of the whiteboard.
The center of the Digital Control Panel, not the EZTub,
must be centered on the left side of the white board.

The system is shipped with the EZTub and three (3) ¼”
thick wall spacers (right) to allow the EZTub and Digital
Control Panel to sit flush with the whiteboard surface.

In our mounting example, the whiteboard is a 3’ x 5’
and sits about 1” out from the wall. Make a mark at 1.5’
on the left side of the whiteboard surface and this will
be where the center blue IR receiver (with the Vaddio
Logo) will be aligned.

Step 2:

Determine the required number of wall spacers to raise the
EZTub and Digital Control Panel to the correct height to be even
with the surface of the whiteboard. In this example, the two ¼”
spacers and the EZTub will provide the 1” height needed.

Step 3:

Stack the EZTub and two (2) spacers. Hold them to the left side
of the whiteboard and center the opening for the Digital Control
Panel on the mark that was made on the whiteboard. Snap in
the Digital Control Panel and adjust the height so the center blue
dot is on the center mark. Using the removal tool, remove the
Digital Control Panel and mark the position of the screws. The
EZTub has two keyhole slots and the spacers have oval slotted
screw holes. While still holding the EZTub and Spacers against
the left side of the whiteboard, make two marks on the wall at the
top of the keyhole slots on the EZTub.

Step 4:

Install the two (2) provided spiral wall anchors, or installer’s
preferred anchors at these marks.

Step 5:

Route the Cat-5e cable from the Squiggle Quick-Connect
Interface and decide if the cabling will run inside the wall behind
the EZTub or will be surface mounted. Each Wall Spacer (see
illustration on right) has a cable pass-thru at the bottom to allow
the Cat-5e cable to pass through the wall to the RJ-45 connector
on the back of the EZTub connector.

EZTub and three (3) all Spacers

Any Whiteboard

Center, Left Side of Whiteboard

Digital Control Panel, EZTub and two (2) Wall Spacers
(left to right below)

Keyhole
Slot

Cable pass-thru into
wall behind EZTub

Squiggle Manual 342-0172 Rev. B Page 6 of 16

Squiggle Video Whiteboard Kit

Step 6 - Putting it All Together:

Plug the Cat-5e cable into the RJ-45 jack on the back of the EZTub and stack the Wall Spacers against the back
of the EZTub routing the cable through the spacers. If the cabling is running into the wall, push the extra cable
slack back into the wall at this time. Place the EZTub and spacers against the wall and over the wall anchors.
Take the two (2) provided #6 x 1.75 pan head screws, position them at the top of the keyhole slots of the EZTub,
snug down the EZTub and the spacers. Make sure that the EZTub is against the whiteboard and is also snug to
the wall. Clip the Digital Control panel into the EZTub and the whiteboard.

Any Whiteboard

Digital Control Panel
Center IR Receiver
with Vaddio Logo
Centered on Left
Side of Whiteboard

Center, Left Side of Whiteboard

Power
and Data

Rear Panel of Squiggle
Quick-Connect Interface

Power and Data Connect to
“TO VIDEO WHITEBOARD” RJ-45 Jack

HD DVI-D

Output (HDMI

with Cable)

DVI-D/HDMI and YPbPr are

Simultaneous HD Outputs

At the Same Resolution

HD YPbPr

Output

SD Composite (CVBS)

Video can be selected

instead of HD Outputs.

Choosing SD turns off

the HD, and vice versa.

Please test the Cat-5e cable continuity prior to final connection. Please do not use “pass­through” or “EZ type” RJ-45 connectors. These pass-thru type connectors do not work well for
professional installations and can be the cause of intermittent connections. For best results
please use standard RJ-45 connectors and test all cables for proper pin-outs prior to
connection to Vaddio products.

Step 7:

At the head end, connect the Cat-5e cable to the RJ-45 jack on the rear panel Squiggle Quick-Connect Interface
labeled “TO VIDEO WHITEBOARD”. Plug the Power Supply into the Quick-Connect Interface and plug the power
supply into the wall outlet.

Squiggle Manual 342-0172 Rev. B Page 7 of 16

Squiggle Video Whiteboard Kit

Step 8 - The “Seems Obvious” Step:

Put the provided batteries in the Digital Pen Sleeve and the Digital Eraser.

• Pen: Twist the pen sleeve cap counter-clockwise and put two (2) CR2032 batteries provided, stacked
positive (+) side up, and return the cap. Put the bullet nose black marker in the pen sleeve.

• Eraser: With a coin, twist the digital eraser cap counter-clockwise and put two (2) CR2032 batteries
provided, stacked positive (+) side up and return the cap.

Step 9 - Setting the 5-Position Dip Switch:

The Squiggle Quick-Connect Interface has a 5-position dip switch accessible on the rear panel. Set the switch
settings for your application. The switch settings are on the following table:

5-Position Dip Switch

Dip

Switch

1 2 3 4 5

UP HD

DOWN SD

HD - 720p/59.94 or

SD - 480i/29.97 - NTSC

HD - 720p/50 or

SD - 576i/25 - PAL

- -

- -

SMPTE Color

Bars OFF

SMPTE Color

Bars ON

Accessible from the rear
panel of the Quick-Connect
Interface

UP - ↑

Down -

↓

Example Set-ups:

• HD, 720p/59.94, Color Bars Off: SW1 = UP, SW2 = UP, SW5 = UP

• SD, 480i/NTSC, Color Bars Off: SW1 = DN, SW2 = UP, SW5 = UP

• HD, 720p/50, Color Bars Off: SW1 = UP, SW2 = DN, SW5 = UP

• SD, 576i/PAL, Color Bars Off: SW1 = DN, SW2 = DN, SW5 = UP

Notes: Default Position for all Switches is UP = HD, 720p/59.94, SMPTE Color Bars OFF.

Switches 3 and 4 are not used and are for future features.
The Color Bars are a video testing convenience only.

Using the Squiggle:

Upon connection of the Squiggle and powering up the Squiggle Quick-Connect Interface, the system will boot up
and the Vaddio splash screen will be seen on the HD 720p or SD display device.

Automatically, the Software Version number, MAC address and the legal notices are displayed briefly. The MAC
will be needed as the Ethernet functions are added to the software and for technical support.

Squiggle Manual 342-0172 Rev. B Page 8 of 16

Squiggle Video Whiteboard Kit

Calibration:

The system will load the default 4’ x 6’ whiteboard calibration size. It is recommended that if you have a 4’ x 6’
whiteboard, perform the calibration process anyway. Any other size whiteboard requires calibration. The process
to calibrate the system is as follows:

1) Touch the Calibration button on the Digital Control Panel and the following screen is displayed.

Important Note:

Remember to put two (2)
CR2032 batteries into the
Digital Pen Sleeve, stacked
with the positive (+) sides up,
to allow the pen to calibrate
the system. See Step 9 of
the Installation Procedures.

The prompt, “Using the Electronic whiteboard marker, tap each highlighted target” will be displayed. Start in the
upper left corner and proceed tapping the targets from top to bottom in the order shown above. When the
calibration is complete, the system is ready for use. If the system won’t calibrate, make sure that you have the
right number (2) and polarity of the pen sleeve batteries installed. If there is an unintentional mistake during
calibration, simply touch the calibration button again to stop the process. To restart calibration, touch the button
again.

To Save the Whiteboard Content to USB Drive:

Put a flash drive into the Quick-Connect front panel USB port. This port supports only FAT32 or FAT16 formatted
drives. Touch the Flash Drive Icon on the Digital Control Panel and the system will show the prompt “Saving
image, Please wait…”

After the image is saved the following prompt is displayed briefly:

At this point, the drive may be removed or left in the USB port for future content to be saved. The image saved
can be loaded into any computer device that can accept the FAT32/16 file format and view the image as a JPEG.

Squiggle Manual 342-0172 Rev. B Page 9 of 16

Squiggle Video Whiteboard Kit

For Best Squiggle Results:

Pen & Eraser Etiquette:

The Squiggle Digital Marker Sleeve is the device that is tracked by the ultra sonic
sensors and the IR sensor in the Digital Control Panel. In order to achieve the
best results, adhere to the following guidelines.

• Always write with the pen tip making contact at a 90° angle (perpendicular) to
the whiteboard surface.

• Carefully and firmly press the marker and marker sleeve to the whiteboard
surface. It is a firm contact that engages the sonic transmitters and allows
the marker to be tracked. Pressing too lightly with the marker and sleeve
may result in line drop outs.

• Use bullet point, regular markers for best results. The low odor markers are
eco-friendly, however these eco markers are difficult to erase as the oils are
removed to prevent the odor. Normal bullet nosed markers work best.

• When pressing the Digital Marker Sleeve and marker at a 90° angle, a slight buzzing sound may be audible.
This is really, really normal. Most people will check the battery by holding it up to their ear - but please do not
insert the pen in your or anyone else’s ear.

• An indication of a possible low battery condition in the Digital Marker Sleeve or Digital Eraser is the inability
to write/erase on the far end of the whiteboard opposite from the Digital Control Panel. Change batteries as
needed.

• When returning the marker cap, the marker sleeve can be triggered if handled improperly. The whiteboard
sensors can receive the pulse and leave a dot or very short line on the video image. If this is undesirable,
turn away from the whiteboard during a session and then put the marker cap on the marker holder.

• Loose clothing such as cuffs or puffy “pirate sleeves” can block the pen transmitters and cause drop outs and
less than acceptable results.

• Porcelain over steel whiteboard surface is magnetic. Please do not attach papers to the whiteboard surface
with a magnet. The paper will interfere with the pen tracking and may produce some wicked-awful lines,
again with mostly undesirable effects.

• The Squiggle uses ultrasonic and IR technology. There are some devices in any presentation environment
that may cause interference with normal operation. Try to mitigate interference between all devices using
ultrasonic or IR technology for best results. The resonating induction inhibitor will cancel most stray
interference, but certainly not all of it.

• If colored Digital Marker Sleeves are purchased as an option, the color ring of the marker sleeve should be
matched to the marker color to avoid multiphasic polarizing regeneration. The color of the marker sleeve ring
will match the color of the video displayed.

• The Digital Eraser works like the Digital Markers. To selectively erase portions of the whiteboard content,
press the eraser firmly against the whiteboard at a 90° angle (perpendicular) to engage the ultra sonic and IR
transmitters. If there are pesky line remnants on the video after trying to erase the whole whiteboard with the
Digital Eraser, these are a result of not holding the eraser at a perfect 90° angle to the whiteboard surface.

To do a mass erase job, first touch the Erase Button on the Digital Control Panel and whip out a
sizeable regular whiteboard eraser device and rub down the whole whiteboard. Remember to
clean the surface with high quality Whiteboard Cleaner to clean and refresh the whiteboard

Erase Button

periodically. Cleaning will make it easier to erase…really.

Squiggle Manual 342-0172 Rev. B Page 10 of 16

Squiggle Video Whiteboard Kit

p

Basic Connectivity Diagram:

Squiggle Attached to Existing Whiteboard (no scale)

Power and Data Cat-5e Cable

(Up to 100’ / 30.48m)

Large Format HD Monitor

or HD Projector

General Specifications:

Squiggle Video Whiteboard Kit

Part Numbers

Dimensions

Mounting Holes

EZTub PCBA

Max. Whiteboard Size

Squiggle Quick-Connect Interface

Connectors

Settings Switches
CAT-5 Cable Distance
Flash Drive Format
Average JPEG File

Size
Power Supply
Dimensions
Weight

999-5441-000: Squiggle Video Whiteboard Kit - North America
999-5441-001: Squiggle Video Whiteboard Kit - International

EZTub: .875” (22.23mm) Thick x 14” (355.6mm) Long x 2” (50.8mm) Wide
Digital Control Panel: .275” (6.99mm) x 10” Long (254mm) x 1.375” (34.925) Wide
Wall Spacers: .25” (6.35mm) Thick x 14” (355.6mm) Long x 2” (50.8mm) Wide

Wall Spacers: Two (2) slotted holes 6” on center
EZTub: Two (2) Keyhole shaped mounting holes

Terminates Digital Control Panel when installed into the EZTub. Extends Squiggle power
and Digital Pen Sleeve data to the Squiggle Quick-Connect Interface.

4’ x 8’ (1.22m x 2.03m)

Power Connector: 5.5mm OD x 2.5mm ID
Whiteboard RJ-45: Supplies power and Serial Data to Whiteboard Digital Control Panel
Ethernet RJ-45: Reserved for future use
Video Outputs: DVI-D and DE-15 for YPbPr-HD and BNC Connector for SD video

For setting HD or SD video, Refresh Rate, Color Bars and for Future Enhancements
Up to 100’ (30.5m)
FAT32 or FAT16
200 KB to 300 KB Depending on Content Density

12 VDC, 3.0 Amp
1-RU Rack Mount - 1.72” (4.4cm) H x 19” (48.3cm) W x 6” (15.2cm) D

3.2 lbs. (1.45329107kg) - Approximate Weight

Video Whiteboard

Quick-Connect Interface

YPbPr 720

DVI-D 720p

(HDMI with Adapter Cable)

DVI-D or

HDMI

HD Monitor

(Simulated VC Feed)

USB Flash Drive

Videoconferencing

System

RAR

Squiggle Manual 342-0172 Rev. B Page 11 of 16

Squiggle Video Whiteboard Kit

Compliance and CE Declaration of Conformity

FCC Part 15 Compliance

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his/her own expense.

Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This
device must accept any interference including interference that may cause undesired operation of the device.

Changes or modifications not expressly approved by Vaddio can affect emission compliance and could void the
user’s authority to operate this equipment.

ICES-003 Compliance

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out
in the Radio Interference Regulations of the Canadian Department of Communications.
Le présent appareil numérique n’emet pas de bruits radioélectriques dépassant les limites applicables aux
appareils numeriques de la classe A préscrites dans le Règlement sur le brouillage radioélectrique édicte par le
ministère des Communications du Canada.

European Compliance

This product has been evaluated for Electromagnetic Compatibility under the EMC Directive for Emissions and Immunity and
meets the requirements for a Class A digital device. In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures.

Standard(s) To Which Conformity Is Declared:
EMC Directive 2004/108/EC

EN 55022 A: 2006 + A1 2007 (CISPR 22:2005/A1:2005) Conducted and Radiated Emissions

EN 55024: 1998 + Amendments A1: 2001 + A2: 2003 - Electromagnetic Compatibility - Immunity

EN 61000-4-2 Electrostatic Discharge

EN 61000-4-3 Radiated Immunity

EN 61000-4-4 Electrical Fast Transients

EN 61000-4-5 Surge Immunity

EN 61000-4-6 Conducted Immunity

EN 61000-4-8 Power Frequency Magnetic Field

EN 61000-4-11 Voltage Dips, Interrupts and Fluctuations

Squiggle Manual 342-0172 Rev. B Page 12 of 16

Squiggle Video Whiteboard Kit

WARRANTY INFORMATION

(See Vaddio Warranty Policies posted on vaddio.com for complete details):

Hardware* Warranty: One year limited warranty on all parts. Vaddio warrants this product against defects in materials and
workmanship for a period of one year from the day of purchase from Vaddio. If Vaddio receives notice of such defects during
the warranty period, they will, at their option, repair or replace products that prove to be defective.

Exclusions: The above warranty shall not apply to defects resulting from: improper or inadequate maintenance by the
customer, customer applied software or interfacing, unauthorized modifications or misuse, operation outside the normal
environmental specifications for the product, use of the incorrect power supply, improper extension of the power supply cable
or improper site operation and maintenance.

Vaddio Customer Service: Vaddio will test, repair, or replace the product or products without charge if the unit is under
warranty and is found to be defective. If the product is out of warranty, Vaddio will test then repair the product or products. The
cost of parts and labor charge will be estimated by a technician and confirmed by the customer prior to repair. All components
must be returned for testing as a complete unit. Vaddio will not accept responsibility for shipment after it has left the premises.

Vaddio Technical Support: Vaddio technicians will determine and discuss with the customer the criteria for repair costs
and/or replacement. Vaddio Technical Support can be contacted through one of the following resources: e-mail support at

[e-mail]

Return Material Authorization (RMA) Number: Before returning a product for repair or replacement, request an RMA from
Vaddio’s technical support. Provide a technician with a return phone number, e-mail address, shipping address, and product
serial numbers and describe the reason for repairs or returns as well as the date of purchase and proof of purchase. Include
your assigned RMA number in all correspondence with Vaddio. Write your assigned RMA number on the shipping label when
returning the product. All returns are subject to a restocking fee without exception (see warranty policies at vaddio.com).

Voided Warranty: The warranty does not apply if the original serial number has been removed or if the product has been
disassembled or damaged through misuse, accident, modifications, or unauthorized repair. Cutting the power supply cable on
the secondary side (low voltage side) to extend the power to the device (camera or controller) voids the warranty for that
device.

Shipping and Handling: Vaddio will not pay for inbound shipping transportation or insurance charges or accept any
responsibility for laws and ordinances from inbound transit. Vaddio will pay for outbound shipping, transportation, and
insurance charges for all items under warranty but will not assume responsibility for loss and/or damage by the outbound
freight carrier. If the return shipment appears damaged, retain the original boxes and packing material for inspection by the
carrier. Contact your carrier immediately.

Products Not Under Warranty: Payment arrangements are required before outbound shipment for all out of warranty
products.

*Vaddio manufactures its hardware products from parts and components that are new or equivalent to new in accordance with industry standard practices.

Other General Information:
Care and Cleaning

Do not attempt to take this product apart at any time. There are no user-serviceable components inside.

• Do not spill liquids or liquid type substances onto the device.

• Keep this device away from food or liquid.

• Clean the whiteboard regularly with a good quality whiteboard cleaner, but do not spray on the electronics

• For smears or smudges on the devices, wipe with a clean, soft cloth.

• Do not use any abrasive pads or caustic chemicals at any time on any Vaddio equipment.

Operating and Storage Conditions:

Do not store or operate the device under the following conditions:

• Temperatures above 40°C (104°F) or temperatures below 0°C (32°F)

• High humidity, condensing or wet environments

• Dry environments with an excess of static discharge

• In outer space (under normal circumstances)

• Under severe vibration

• High humidity, condensing or wet environments, inclement weather on in a swimming pool

• Dusty environments or outside in direct sunlight

• Under severe vibration

or online at www.vaddio.com.

Squiggle Manual 342-0172 Rev. B Page 13 of 16

Squiggle Video Whiteboard Kit

Squiggle Notes:

Squiggle Manual 342-0172 Rev. B Page 14 of 16

Squiggle Video Whiteboard Kit

Inside Back Cover (blank)

Squiggle Manual 342-0172 Rev. B Page 15 of 16

Squiggle Video Whiteboard Kit

Toll Free: 800-572-2011 ▪ Phone: [phone] ▪ FAX: [phone]

9433 Science Center Drive, Minneapolis, MN 55428

©2011 Vaddio - All Rights Reserved. Reproduction in whole or in part without written permission is prohibited. Specifications and pricing are subject to
change without notice. Vaddio, Quick-Connect, EZTub, PowerRite, HSDS and EZCamera are registered trademarks of Vaddio. All other trademarks are
property of their respective owners. Document Number 342-0172 Rev. B

Squiggle Manual 342-0172 Rev. B Page 16 of 16

www.vaddio.com