Page 1
2CH Mobile Video Recorder
User Manual
2016 AUG V1.0
※The memory card dose not includes, please buy it separately.
Page 2
2CH Mobile Video Recorder User Manual
i
Health and Safety Information
And Usage Guidelines
Dear Customer,
We appreciate your purchase, if you meet any problem during the usage,
please contact retailer immediately. The important, we remain the right to
change and improve our product without any notices.
Read all following instruction carefully before set up and use：
System Installation Cautions
Before install system, get knowledge of charge and power cable
wiring.。
The system must installed by technicians of professional vehicle
manufacturers or professional vehicle installation service.
Place the device in a well-ventilated location inside a vehicle
Please select the storage device following the storage device
manufacturers advice, in order to meet a long time, a large amount of
data read and write requirements. For ensure the storage devices
quality, please purchase from the official channel.
If you meet any problem during the installation, please contact
technicians of dealer or authorized vendor immediately.
Vehicle System Cautions
Do not let any solid or liquid seep inside the device.
Do not disassemble this equipment, repair or replacement any
component. If the machine does not work properly, please contact the
manufacturers or dealer, we will solve problems as soon as possible.
For avoiding battery leakage damage, Please remove battery from
remote control when you are not plan to use remote control recently.
Please install ground first to avoid static / lightning might broke the
recorder.
Page 3
2CH Mobile Video Recorder User Manual
ii
Usage environment cautions
Please place and use this product under the recommended
temperature, avoid direct sunlight, or near heat sources.
Do not install the machine in moist environments.
Do not expose the machine in smoky, dusty environment
Do not drop the machine for avoiding strong collision
Please install this product in ventilated locations, do not block the
product's vents.
Please use this device within the rated input and output range of
current and voltage.
This device is design for electronic engineering prolonged use; do not
place the device next to flammable or explosive materials. In order to
avoid safety problems.
Page 4
2CH Mobile Video Recorder User Manual
iii
Table of Contents
A.
Accessories
................................................................................ - 1 -
B. Key Features .............................................................................. - 2 -
C. Specifications
............................................................................. - 3 -
D. Product Description ......................................................................... 5
E. Memory Disk .................................................................................... 6
F. Cables Installation Instructions ........................................................ 7
G. Vehicle Installation ........................................................................... 8
H. Recording ...................................................................................... 10
I. Live Display on PC ........................................................................ 11
J. File Backup .................................................................................... 13
K. Configuring the Memory Disk ........................................................ 15
L. Video Playback .............................................................................. 18
M. Snapshot Tool ............................................................................... 19
N. Formatting / Restoring the Memory Disk ....................................... 20
O. WiFi Connection ............................................................................ 22
Page 5
2CH Mobile Video Recorder User Manual
- 1 -
A.
Accessories
Before you use our product, please make sure everything that we list below
is includes in this package. Contact retailers if this package missing any item.
※The memory card sold separately
Standard package includes:
1. Camera *2
2. 2.5M Power cable *2
3. Charge cable
4. USB WIFI dongle
5. Velcro tape
Optional
8/16/32G SD memory card, Class10 or above.
Page 6
2CH Mobile Video Recorder User Manual
- 2 -
B. Key Features
1. Miniature video recording system with 2-way video input, which
suitable for vehicle.
2. H.264 video compression screen without distortion.
3. Vehicle charger, Low power consumption and excellent heat radiation.
Lithium battery is not used to eliminate risks of overheating and
“explosion”.
4. Turn on the engine, automatic start loop recording; Turn off the engine,
saving the data and shutdown the video recording automatically.
5. Built-in gold capacitor. If the machine turns off, the video recording will
be automatic delay, which is ensure that the data saving into the
memory card.
6. The external USB WiFi dongle is available for immediate viewing and
backup file on your mobile device.
7. Made in Taiwan.
Page 7
2CH Mobile Video Recorder User Manual
- 3 -
C. Specifications
DVR Specification
Items
Description
Video input
2 Channel, support similar 2 channel cameras
Frame Size
NTSC: 30 fps (D1); PAL: 25 fps (D1)
Voltage and
Current
DC12V, 250mA (When the old capacitor is charging, Host
voltage and current are about 500mA)
Power supply
(a) ACC ON power offer by 12V vehicle battery
(b) ACC OFF delay about 30 seconds shut down the main
power
(c) ACC OFF Standby current 5mA or less
(d) Built-in gold capacitor, after the main power shut down, it
can be delayed for 3 seconds to save the file for the host.
Operating
Temperature
-15°C~ 50°C
Storage
Recommend to use SDHD card, 4G or above, class 10 or
better.
Recording
Automatically starts continuous recording when powered on
Recording
Content
Date, time, video, audio
Storage
format
Specific file format, need to play with a dedicated play
software
Time setup
Automatic calibration by GPS signals. If GPS signal is
unavailable, internal clock will be used.
Input and
output device
(a) Red light：Flashing indicates the video is recording
(when G-sensor active, the red light flicker higher
frequency).
(b) Green light：Light always on is indicated power on.
(c) DC12V power input.
(d) Image input aperture (1 Vp-p composite video output, 75
ohms), video input has to distinguish between PAL or
NTSC system.
Page 8
2CH Mobile Video Recorder User Manual
- 4 -
Note: Product specifications are subject to change without any notice.
Camera Specification
Power
Input voltageDC5V~DC12V ±10%；Current consumption
about 500mA
Image
resolution
NTSC/PAL
Highest at 30FPS
CMOS
1/4 inch CMOS
Camera angle
horizontal angle 110°/ vertical angle 55°/ diagonal angle
130°
Camera lens
2.0mm (optional)
Temperature
range
Operating temperature：-20°C～60°C (Non-confined space
with naturally cooling environment)
Preservation temperature：-40°C～85°C
Output
terminal
Micro Din
Size
30x43x50mm
Note: Product specifications are subject to change without any notice.
(e) USB 2.0 Input aperture( can select the optional wireless
network card connection to WiFi wireless Internet)
Page 9
2CH Mobile Video Recorder User Manual
- 5 -
D. Product Description
Vehicle device
Power
Recording
SD card slot
Crew for protective cover
Page 10
2CH Mobile Video Recorder User Manual
- 6 -
E. Memory Disk
(1). Loose the screw in counterclockwise rotation, and open the protective cover to
insert/remove SD card.
(2). Please refer to the other sections for format / restore the memory card.
CAUTION
(1) Recommend using SDHC Card, Class 10 above (8G or better)
(2) Before using the memory disk, please format the disk first using the
software player in the CD-ROM. If not, device will automatically
erase all data in the memory disk before recording.
(3) To ensure recording quality, please do not use adapter card with
Micro SD card. Doing so may lead to bad connection due to shock
and vibration.
(4) All memory disks have limited lifespan. Please regularly watch
videos on PC and check the memory disk to ensure proper
functioning
(5) Strongly recommend regular inspection and backup important data.
The shock and vibration can cause physically damaged to memory
disk, resulting in choppy playback or data damage.
SD card slot
Protective cover
Page 11
2CH Mobile Video Recorder User Manual
- 7 -
F. Cables Installation Instructions
Cables
(1) Power connecter
(2) Channel 1 Video Input
(3) Channel 2 Video Input
(4) WiFi Dongle connecter
NOTE: Use this device with compatible vehicle cameras
Power Cable
(1). Power Adapter - Female connector.
(2). Live Wire (red): Wire to the positive pole of Engine Starter. (+)
(3). Earth Wire (Black): Wire to Negative Pole. (-)
1 2 3 4 a b c
Page 12
2CH Mobile Video Recorder User Manual
- 8 -
G. Vehicle Installation
Example Installation
CAUTION
(a) For installation by none-technician, please use tapes instead of boring tools to
avoid damaging the electrical and gasoline system。
(b) Recommended using hose covered wire at high temperatures and engine
wiring portion for extend device lifespan.
(c) For safety, switch off ignition before installation, and please keep away from
gasoline pipeline and tank.。
(d) For avoiding vibration that resulting in poor contacting problem to video
adapter, do not recording video by the SD card transferred by microSD.
(e) Before inserting wires through holes, temporarily wrap the terminal with tape to
prevent bad connection from accumulated dirt or debris. Tightly seal all
electrical connection with tape to prevent loose connection or leak leaking to
the connection.
(f) Connect the power behind the key ignition and fuse (not directly to the vehicle
battery) to avoid depleting the battery.
(g) Recommended to install the device into the trunk or less susceptible to external
impact position. To reduce a direct damage to the device that causes data loss.
Page 13
2CH Mobile Video Recorder User Manual
- 9 -
DVR Installation Diagram
1. Method：Connect to battery, set up the switch.
Independent power supply
2.Method：Connect to Motorbike power supply (ACC ON),
when engine is on turn on automatically.
Page 14
2CH Mobile Video Recorder User Manual
- 10 -
H. Recording
1. Power on/Recording:
Power On, and wait about 30 seconds later, the boot is complete. During the recorder
boot process, The PWR Green light is always on. The red light flashing represents the
beginning of recording.
Lights indicate:
Power：Green light always on is indicating device power on.
Recording：Red light flashing represents the beginning of recording.
2. Power off/Stop recording
A delay of approximately 3 seconds after the power is turned off to stop recording,
and then the system will write buffer zone back to the SD card. After the light goes out,
you can remove the memory card reader of the video file.
Power
Recording
Page 15
2CH Mobile Video Recorder User Manual
- 11 -
I. Live Display on PC
Run the player software , the software display following：
NOTE: The software requires Direct X version 9.0 or above.
1. Viewer schematic diagram
1
Camera 1
2
Camera 2
3
Functions
4
Keyboard
1
2
3
4
Page 16
2CH Mobile Video Recorder User Manual
- 12 -
2. Function Description
Shutdown
Minimize window
Open file, choose file to play
Recoding date line
Backup tool
Screenshot tool
Setting
Reset tool
G-sensor
Not support on this model
Page 17
2CH Mobile Video Recorder User Manual
- 13 -
J. File Backup
Upload files from SD card to PC.
On the player software, select and the following window will open.
To backup video：
Step one. Select the path of the memory disk
Step two. Select the footage that you want to backup
Step three. Select the Backup Format:
1
2
3 4 5
Page 18
2CH Mobile Video Recorder User Manual
- 14 -
Backup Format:：
(1) Raw file (RAW)
The file ending with *.sd
(2) AVI File (*.avi)
Cam1 indicates Cam1 footage
The file ending with*.avi
Cam2 indicates Cam2 footage,
The file ending with*.avi
Note：Recommended backup file with RAW format. The RAW
backup format can save the original data that Backup all
footage information (video, audio, G-SENSOR, speed and
GPS data). However, the AVI format can backup video, time
and audio data, the GPS and G-SENSOR data will loss.。
Step four. Select the backup beginning and ending time
Step five. Select the destination folder of the file and Select Backup to start
Page 19
2CH Mobile Video Recorder User Manual
- 15 -
K. Configuring the Memory Disk
Before use please plug SD card into card reader, then plug card reader into PCs USB
input slot, click the “CarBox2”icon on the screen, set up video format and display
method, after done, plug SD card back into MDE16, it will automatic save changes。
In PCs player, fallowing will show up after click ：
1. Base Configuration
1
Video Frame
Rate
Set the number of frames per
second.,
NTSC30、15
PAL
30、25、20、15、10、5
2
Car
Information
Not support on this model
Page 20
2CH Mobile Video Recorder User Manual
- 16 -
3
Password
This function can encrypt the
data and prevent unauthorized
access. Maximum letters.
Password can contain
maximum 15 letters
For
example:123456789123456
After passwords are setup,
you will need to enter the
password to access the disk
(video playback, configuration,
formatting, etc.)
★NOTE: Password is case-
sensitive. Always keep
passwords in secure location.
4
Playback
Password
Not support on this model
5
Time zone
Not support on this model, can
be changed by player
6
Copy me to
storage
Copy and save Player to SD
Card
7
Unit of Speed
Not support on this model
8
G-sensor
Sensitivity
Not support on this model
9
Audio
Recording
Not support on this model
10
Daylight
Saving Time
Not support on this model
Page 21
2CH Mobile Video Recorder User Manual
- 17 -
2. WiFi Configuration
1. SSID and password preset on「SSID」、「 12345678」
2. SSID and password are replaceable (at least 8 words on password)
Page 22
2CH Mobile Video Recorder User Manual
- 18 -
L. Video Playback
We offer video playback software on PC.
1. Playback on Computer
On the software player, select and the following window will appear:
(1) Select the path of the memory disk or a backup file on the hard disk.
(2) Double click the desired footage to play the file.
1
2
Page 23
2CH Mobile Video Recorder User Manual
- 19 -
M. Snapshot Tool
While playing a footage on the software player, you may take a snapshot of the current
frame by selecting snapshot tool is will showing the window below.
The image had been shot can be found in /Snapshot folder. Otherwise, The player can
selecting setting the destination folder and save the file to *.bmp format.
Page 24
2CH Mobile Video Recorder User Manual
- 20 -
N. Formatting / Restoring the Memory Disk
Q1. Under which condition you require format Memory disk?
Before using a newly purchased memory disk, or when repurposing a used disk for the
device, the memory disk must be formatted first.
Q2. When you need to restore the Memory Disk?
If you want to repurpose the memory disk for other uses (e.g. for computer or digital
camera), you need to restore the disk. All recorded data will be erased from the disk
CAUTION
(1) Before formatting or restoring, make sure the disk
is unlocked.
(2) If you are still unable to format/restore the
memory disk, close the software player, and then
re-open the player as administrator:
Unlock SD
Locked SD
Page 25
2CH Mobile Video Recorder User Manual
- 21 -
Q3. How to format/restore the memory disk?
To format/restore the memory disk：
(1). Plug SD card in to card reader, then plug carder reader into PCs USB slot。
(2). Run the palyer software ,select to open the disk format window.
(3). Select the memory disk,as your requirement select the Format or Restore button.
(4). SD card only can be use after been「format」or「restore」.
a. Select the SD card
b.Format SD card
c. Restore SD card
Page 26
2CH Mobile Video Recorder User Manual
- 22 -
O. WiFi Connection
1. Play store search” VacronPlayer” and download.
2. Open WLAN then link「SSID」, with password「12345678」 . (to change SSID and
password please refer to page 20)
3. Open APP ”VacronPlayer”, click「device list」、「open new」, then type any name you like.
4. Click the device name just named, then switch to 「all channel, the live view will
show up right away.
5. There are four functions available：Live screen shoot、Live video record、video
playback、video download.
6. Can also watch saved video or photo.
CH-1
Video playback
Page 27
2CH Mobile Video Recorder User Manual
- 23 -
Saved video playback
Device info
Set up a new device
1. Name a device
2. IP on the device：WIFI will automatic
find the IP address
3. Stream port number： preset on 80
4. Account number：preset admin
5. password：preset (don’t need to
change)
6. Device channels：depend on the
device cameras
When done set up, save then log out.
Device list
Page 28
2CH Mobile Video Recorder User Manual
- 24 -
Chose to display all channel on this device,
it will jump to channel one for live view.
CAUTION
1. Live view will be delay because of the network data transmission.
2. Video playback can only be use if date is still on the SD card, if the data
has been rewrite, then will not able to be find/download.
3. Please disconnect the WiFi after use, otherwise might not able to use
internet on your device.
4. If there is not HUD as option, please use PC and mobile device once every
month to keep system run normally.
Page 29
For more info
Please check our website
http://vvr.vacron.com.tw Made in Taiwan
Loading...