V3 Semiconductor V292PBC-40REVB2, V292PBC-33REVB2 Datasheet

V292PBC Rev. B2

LOCAL BUS TO PCI BRIDGE

FOR DE-MULTIPLEXED A/D PROCESSORS

V3 Semiconductor reserves the right to change the specifications of this product without notice. V292PBC and V292BMC are trademarks of V3 Semiconductor. All other trademarks are the property of their respective owners.

• Glueless interface between AMD’s Am29030/ 40 processors and PCI bus

• Fully compliant with PCI 2.1 specification

• Configurable for primary master, bus master, or target operation

• Up to 1Kbyte burst access support on both local and PCI interface

• 576 bytes of programmable FIFO storage with DYNAMIC BANDWIDTH ALLOCATION™

• Two channel DMA controller

• Enhanced support for 8/16-bit local bus devices with programmable region size register

• 16 8-bit bi-directional mailbox registers with doorbell interrupts

• Dual bi-directional address space remapping

• On-the-fly byte order (endian) conversion

• Optional power on serial EEPROM initialization

• I2O ATU and messaging unit including hardware controlled circular queues

• Flexible PCI and local interrupt management

• Support for real-mode DOS "holes"

• Ability to generate both Type 0 and Type 1 configuration cycles

• 33MHz and 40MHz local bus versions available with independent PCI operation up to 33MHz

• Low cost 160-pin EIAJ PQFP package

V292PBC provides the highest performance, most flexible, and most economical method to directly connect Am29030/40 processors to the PCI bus. V292PBC is also a suitable candidate for a variety of 32-bit de-multiplexed local bus applications based on Motorola, IBM, DEC and Hitachi embedded processors - where a minimal amount of glue logic is required. V292PBC may also be used in systems without a CPU for a generic PCI master/target interface.

V292PBC Rev B2 is the first I2O ready PCI bridge, fully backward compatible with V292PBC Rev B1. The PCI bus can be run at the full 33MHz frequency, independent of local bus clock rate. The overall throughput of the system is dramatically improved by increasing the FIFO depth and utilizing the unique DYNAMIC

BANDWIDTH ALLOCATION™ architecture. Access to the PCI bus can be performed

through two programmable address apertures. Two more apertures are provided for PCI-to-local bus accesses. There are 32-bytes of read FIFO’s in each direction, 16-byte dedicated for each aperture. V292PBC also includes bi-directional remapping capabilities, and on-the-fly byte order conversion .

Two DMA channels are provided for autonomous PCI-to-Local/Local-to-PCI transfers. Mailbox registers and flexible PCI interrupt controllers are also included to provide a simple mechanism to emulate PCI device control ports.

The part is available in 160-pin low cost EIAJ Plastic Quad Flat Pack (PQFP) package.

Am29030/40

CPU

V292BMC MEMORY

CONTROL

D R A M

ROM

V292PBC

LOCAL TO

PCI BRIDGE

TYPICAL APPLICATION

PERIPHERAL

PCI

PCI SLOT or EDGE CONNECTOR

V292PBC

This document contains the product codes, pinouts, package mechanical information, DC characteristics, and AC characteristics for the V292PBC. Detailed functional information is contained in the User’s Manual.

V3 Semiconductor retains the rights to change documentation, specifications, or device functionality at any time without notice. Please verify that you have the latest copy of all documents before finalizing a design.

1.0 Product Codes

2.0 Pin Description and Pinout

Table 2 below lists the pin types found on the V292PBC. Table 3 describes the function of each pin on the V292PBC. Table 5 lists the pins by pin number. Figure 1 shows the pinout for the 160-pin EIAJ PQFP package and Figure 2 shows the mechanical dimensions of the package.

Table 1: Product Codes

Product Code Processor Bus Type Package Frequency

V292PBC-33 REV B2 Am29030/35/40 32-bit de-multiplexed 160-pin EIAJ PQFP 33MHz V292PBC-40 REV B2 Am29030/35/40 32-bit de-multiplexed 160-pin EIAJ PQFP 40MHz

Table 2: Pin Types

Pin Type Description

PCI I PCI input only pin.

PCI O PCI output only pin.

PCI I/O PCI tri-state I/O pin.

PCI I/OD PCI input with open drain output.

I/O

TTL I/O pin with 4mA output drive.

I TTL input only pin.

TTL output pin with 4mA output drive.

V292PBC

Table 3: Signal Descriptions

PCI Bus Interface

Signal Type R

Description

AD[31:0] PCI I/O Z Address and data, multiplexed on the same pins.

C/BE[3:0] PCI I/O Z Bus Command and Byte Enables, multiplexed on the same pins.

PAR PCI I/O Z Parity represents even parity across AD[31:0] and C/BE[3:0].

FRAME PCI I/O Z

Cycle Frame indicates the beginning and burst length of an access.

IRDY PCI I/O Z

Initiator Ready indicates the initiating agent’s (bus master’s) ability to complete the current data phase of the transaction.

TRDY PCI I/O Z

Target Ready indicates the target agent’s (selected device’s) ability to complete the current data phase of the transaction.

STOP PCI I/O Z

Stop indicates the current target is requesting the master to stop the current transaction (retry or disconnect).

DEVSEL PCI I/O Z

Device Select, when actively driven by a target, indicates the driving device has decoded its address as the target of the current access. As an input to the initiator, DEVSEL indicates whether any device on the bus has been selected.

IDSEL PCI I

Initialization Device Select is used as a chip select during configuration read and write transactions. It must be driven high in order to access the chip’s internal configuration space.

REQ PCI O H

Request indicates to the arbiter that this agent requests use of the bus.

GNT PCI I

Grant indicates to the agent that access to the bus has been granted.

PCLK PCI I PCLK provides timing for all transactions on the PCI bus.

PRST PCI I/O Z/L

Acts as an input when RDIR is high, an output when RDIR is low. As an input it is asserted low to bring all internal PBC operation to a reset state.

PERR PCI I/O Z

Parity Error is used to report data parity errors during all PCI transactions except a Special Cycle.

SERR PCI I/OD Z

System Error is used to report address parity errors, data parity errors on the Special Cycle command, or any other system error where the result will be catastrophic.

INT[A:D] PCI I/OD Z Level-sensitive interrupt requests may be received or generated.

V292PBC

Local Bus Interface

Signal Type R Description

ID[31:0] I/O4 Z Local instruction and data bus.

LA[31:2] I/O4 Z Local address bus.

BWE[3:0] I/O4 Z Local bus byte write enablesb.

R/W I/O4 Z Read/Write.

LREQ I/O4 Z Asserted low to indicate the beginning of a bus cycle.

RDY I/O4 Z Local Bus data ready.

LBREQ O4 L

Local bus request: asserted by the chip to initiate a local bus master cycle.

LBGRT I Local bus grant.

LPAR[3:0] I/O4 Z Local bus parity.

BURST I/O4 Z Burst request.

ERR I/O4 Z Bus Time-out error. LINT O4 H Local interrupt request.

LRST I/O4 L/Z Local bus RESET signal.

MEMCLK I Local bus clock.

Serial EEPROM Interface

Signal Type R Description

SCL/LPERR O4 X EEPROM clock. Local parity error.

SDA I/O4 X EEPROM data.

Configuration

Signal Type R Description

RDIR I

Reset direction. Tie low to drive PRST out and LRST in, high to drive LRST out and PRST in.

Table 3: Signal Descriptions (cont’d)

V292PBC

2.1 Test Mode Pins

Several device pins are used during manufacturing test to put the V292PBC device into various test modes. These pins must be maintained at proper levels during reset to insure proper operation. This is typically handled through pull-up or pull-down resistors (typically 1K to 10K) on the signal pins if they are not guaranteed to be at the proper level during reset. Table 4 below shows the reset states for test mode pins:

Power and Ground Signals

Signal Type R Description

POWER leads intended for external connection to a VCC board plane.

GND -

GROUND leads intended for external connection to a GND board plane.

a. R indicates state during reset. b. Can also be programmed as Byte Enable for both Read/Write in Rev B2.

Table 4: RESET State for Test Mode Pins

PIN# 134 135 153

Connection Pull-Down Pull-Up Pull-Up

Table 5: Pin Assignments

PIN # Signal PIN # Signal PIN # Signal PIN # Signal

1 V

41 V

81 V

121 V

2 INTD 42 AD14 82 LA23 122 LA6 3 PRST 43 AD13 83 ID8 123 ID25 4 PCLK 44 AD12 84 LA22 124 LA5 5 GNT 45 AD11 85 ID9 125 ID26 6 REQ 46 AD10 86 LA21 126 LA4 7 AD31 47 AD9 87 ID10 127 ID27 8 AD30 48 AD8 88 LA20 128 LA3

Table 3: Signal Descriptions (cont’d)

+ 11 hidden pages