Page 1
Take down the model number for reference.
Model No.： Series No.：____________________
All rights are reserved by our company. If there is any change, it is
subject to material product without any prior notice.
Interactive Touch All-in-one
User Manual
Please read this manual very carefully before using,
And keep it properly for any further reference.
Page 2
1
Safety warning:
For your safety, please read the notes below very carefully before using and keep
it properly for any reference.
Put the equipment in the well-ventilated environment.
Don’t put materials such as newspaper, table cloth and curtain above the air
hole of the equipment.
Don’t leave the equipment near the open fire such as the lighted candle.
Don’t spray on the equipment, such as leave bottle full of water far away
from the equipment.
To avoid the equipment to fall, please make sure the whole product is on the
stand or wall mount properly. Likewise, don’t put the equipment on the
unstable stand, cart and table.
While hanging the equipment on the wall mount, make sure to ask the
professionals to do this job.
TypeⅠequipments (with three core power cord and ground connection)
should be connected to the outlet with ground connection protection.
Power plug is the disconnect part; it should be easy to remove.
To type Ⅰ(with three core power cord and ground connection) and typeⅡ
multimedia equipment (with two core power cord and without ground
connection),while open the power supply, make sure the ground connection
protection to typeⅠis proper. In the multimedia system, the equipment
connected with communication network and the equipment to wired network
should meet the specific isolation requirement.
Page 3
2
The terminal with is dangerous. While connecting this terminal to
outer lead, make sure to ask professionals to do this job. Or use existing
down-lead and flexible cord to finish the connection.
Don’t put the battery (battery pack or assembled battery) in the environment
such as sunshine and hot fire.
To protect the environment, collect the waste battery along with the local
recycling method.
If the equipment has replaceable lithium battery, please note:
It is in explosion hazard while not replacing the waste battery.
The waste battery can only be replaced with the same or equivalent
battery.
Warning:
To avoid damage to the product, make sure the equipment is tightly fixed on
the floor or the wall in strict accordance to the installation manual.
The finite network antenna connected with the equipment must be isolated
from the ground connection protection. Otherwise, it is in the risk of catching fire.
Page 4
3
Contents
Safety warnings -------- ---- ---- ---- ---- ------ ---- ------------------------------------------------------------------------01
Contents -------------------------------------------------------------------------------------------------------------------03
Product usage note ------------------------------------------------------------------------------------------------------04
The product functions and features -------------------------------------------------------------------------------------05
Installation ----------------------------------------- ------ --- ---------------------------------------------------------------07
Graphic appearance and connection instructions ---------------------------------------------------------------------08
Remote control description ---------------------------------------------------------------------------------------------10
Basic operations ------------------------------------------------------------------------------------------------------------11
Connections and settings --------------------------------------------------------------------------------------------------13
Menu operation -------------------------------------------------------------------------------------------------------------18
Touch screen software installation and use -----------------------------------------------------------------------------26
Computer specifications --------------------------------------------------------------------------------------------------29
Touch screen specifications------------------------------------------------------------------------------------------------30
Troubleshooting -------------------------------------------------------------------------------------------------------------30
Maintenance ------------------------------------------------------------------------------------------------------------------32
Page 5
4
Products using important notes
(1)Important Notes of moving the all in one PC
Please make sure the unplug the plug from power
socket when moving the machine, and disconnect
antenna, audio/video cables, and any fixed cables
It requires 2 or more people to move the machine.
Please grasp the frames steadily as below when you
move the machine.
(5)Do not repair, modify or disassemble the product, please
wait for the maintenance technicians’ check and repair
(2)Don’t climb on the machine. It is very dangerous to
climb on the machine.
(6)When the malfunction occur, Smoking or emits an odor,
please turn off the machine and unplug the plug. Please
contact the maintenance technicians
When you are make sure the smoke and odor has
disappeared.
(3)While not in the use of the product, please turn off
the power and unplug the plug. Even if the machine is
in standby state, The All-in-one PC has not disconnect
with the power supply completely, so there will be
some electricity consumption
(7)If the product downfall or out frame damage, please turn
off the power immediately, and unplug the plug. Please
contact the maintenance technicians
(4)Please don’t touch the antenna, power line or other
connected power lines or power supply when there are
thunders or lightning
(8)Please unplug the power plug before cleaning
Please do not use solvent to clean the all in one PC such
as gasoline or thinner.
This kind of solvent will damaged outer frame of
damaged the surface.
If the rubber or vinyl products with all in one PC contact
for a long time, there may leave stains
Please use the soft cloth to clean the surface of all in one
PC when cleaning the surface.
Page 6
5
The product functions and features
Touch function
Built-one touch function, touch operation can be carried out directly on the screen.
TV function
1. Multilingual menu.
2. Full-function infrared remote control.
3. Full-channel auto-tuning.
4. AV (video), YPBPR (component), PC (computer) and digital HDMI, USB interface.
5. Support SDTV and HDTV modes (480i / 480p, 576i / 576p, 720p, 1080i / 1080p).
6. Automatic standby after 10 minutes of no signal.
7. Two multimedia interfaces, with movies, music, pictures and text playback.
8. Auditory function alone.
9. Variety of sound and video effects modes.
10. Motion compensation function.
Computer monitor function
1. Provides a large screen display, high resolution and excellent color accuracy.
2. Provides a dynamic display area, automatic resizing, automatic centering, and perfect geometry.
3. Supports a variety of computer display formats, and has an adaptive display.
Multimedia features
1. Intelligent user interface, simple operation.
2． Picture browsing, music player, video player.
3． Support U disk, USB mobile hard disk, MP3, card readers and other USB storage devices.
The product features
1． This product is embedded Touch ultra high-speed infrared touch screen with anti-glare, writing sensitivity,
high stability, fast response, touch-free driving and other characteristics; supports multi-touch, enabling objects to
drag, zoom and rotation.
2. High-quality LCD screen, high brightness, high contrast, digital progressive display, color optimization
features, motion picture and still image quality improvement function, real restore perfect picture .
Page 7
6
3． Video has a very clear 4K or 3D and other special effects.
4. Part of PC applies the modular design, all internal wiring; PC modules overall swap, easy maintenance.
5. Slim, stylish and lightweight.
6. Ultra-low standby power design, with automatic power saving feature.
7. Common port at front, signal access automatic switching.
8. Overall all-in-one designs, highly integrated, enabling a key switch and remote control switch product.
9. Extensions and compatibility, support windows \ Linux and other operating systems; scalable wireless
microphones, WIFI, Bluetooth, 3G and so on.
Main accessories
Above pictures for your reference only, please refer to actual product .
Page 8
7
Installation
Page 9
8
Graphic appearance and connection instructions
The indicator of PC will have no function, because some models are without PC built-in.
PC Interface
Interface on front frame
Please note the distinctions, because USB-Host and USB-Touch have same look and shape.
Page 10
9
TV Interface
Page 11
10
Remote control description
Replacement of remote control battery
Open the battery back cover of the remote control; Slide the back cover along the direction of arrow.
Installation response positive and negative installation specifications AAA batteries, to ensure positive and
negative corresponding, please don’t mix the new and old battery.
After the battery installation, along the direction of the arrow to push the back cover.
Page 12
11
Control range
Around 8 m distance from the remote control receiver, 30
degrees within the scope of left and right side, the remote
control can work normally.
Notice
Pay attention to the following matters when using remote control：
Open the remote control’s back cover of the battery, and then put two no.7 batteries into the battery box
finally closed the battery cover.
Please aim the remote control against the front shell of receiving window. If there is obstacle between the
host machine and the remote control, there may be malfunction on remote control.
In order to ensure the operation of the remote control is in good performance, if you found any abnormal
operation, please replace the battery immediately.
Don’t mix the new and old different model battery.
When Battery power is weak, the electrolyte leakage phenomenon happens sit will damage the remote
control. Once you found the electric power is weak which should replace the battery as soon as possible.
Please take out the battery if does not use the remote control for a long time, in case of battery electrolyte
leakage.
Battery should not be exposed to such as sunlight, Coffining or hot environment.
Basic operations
When you open the all-in-one, you need to pay attention to the following operations:
All-in-one boot
After power on all-in-one, TV on the front panel lights red, press the Power button on the front panel, the red light
flashes for about five seconds, and then the built-in TV and PC section will boot at the same time, TV and PC lights
will be lit blue and green. If you only need to open the TV, you can open it via sleep button on the front panel or
power button of the remote control.
Page 13
12
All-in-one shutdown
The initial state
after press the POWER button (a button off)
PC shutdown
TV boot PC boot
PC, TV boot PC off
then TV and then shut down
C boot, TV shutdown
PC unchanged, TV boot
All-in-one can be via a key operation to achieve TV and PC shutdown, process is as follows:
In case of an accident you need to force shut down all-in-one, press the POWER button for more than 3 seconds,
and then all-in-one would be forced to close.
Backlight off
Press the sleep button on the front panel of the TV to make backlight off, meanwhile other parts of all-in-one is still
working properly, TV power indicator light turns from blue to red, and then press a sleep button again, the
backlight is turned on.
Selecting the signal source
Note: The signal source of All-in-one with the 4K function is as Figure -1, the signal source of All-in-one with 3D
features shown as Figure -2.
Via the key
Press SOURCE key on the front panel, the pop-up signal
source list.
By P + P-up and down buttons to select the signal source.
Press SOURCE key to select and confirm signal source.
Via remote control
Press SOURCE button on the remote control to bring up
the signal source list, as shown.
By remote control “▲▼ ”key to select the signal source.
Finally press ENTER to confirm the remote control.
Page 14
13
Connections and settings
Distance Sensing
There is a distance sensor built-in front control panel. The
Interactive LED touch screen will be turned off automatically once
there is anything blocked distance sensor about 5 to 15 cm for
20-25 seconds.
This function is mainly designed for educational application.
Generally the Interactive LED touch screen will be placed behind
the push-draw blackboard. Once the blackboard closed, the
Interactive LED touch screen will be turned off automatically to
save energy and produce less heat.
Video automatically switch
PC inside all-in-one share HDMI1 port channel with front embedded ports, the default is the built-in PC connection
HDMI1 channel, when an external device is connected to the front HDMI port, HDMI1 channel immediately
switch from PC to the front port.
When the built-in PC and external device of front HDMI port connect it simultaneously, and if need to use the
built-in PC, you need to disconnect the front HDMI port and an external device.
Installation and removing of modularized PC
The modularized PC box is easy for installation and
maintenance.
The modularized PC is built in back of all-in-one.
Please loosen the screws and grasp the PC to move it
out smoothly.
Please do not remove the PC when works well. If
necessary, please make sure the power of all-in-one is off
PC before removing.
The installation of OPS and Mini ATX PC are same.
Page 15
14
External computer is connected to all-in-one
Through the front port
Use an HDMI cable to connect the external computer to the all-in-one’s front HDMI port.
One using a USB cable to the front USB-Touch port to connect to an external computer's USB port.
After 3 connections, turn one machine and computer, using the remote control or buttons to select the
appropriate signal source (pre-HDMI port corresponding to the signal source HDMI1), external computer
may need to install touch-screen management software.
Through the rear port
Use an HDMI cable to connect the external computer to the all-in-one’s rear HDMI port; also be connected
to an external computer and all-in-one via VGA cable and audio cable, while only using one of two ways at
the same time.
Use a USB cable to connect the all-in-one’s front USB-Touch port to an external computer's USB port.
After connections, turn on all-in-one and computer, using the remote control or buttons to select the
appropriate signal source, the external computer may need to install touch-screen management software.
When an external computer access, set the optimal resolution of 1920 * 1080;
Part of the connection cable requires the user to provide by their own.
Page 16
15
Audio and video devices connections
AV in
Using the AV cable to connect audio and video devices with AV output function, yellow for video, red for
the right channel, white for the left channel.
After connected cables, open all-in-one and audio and video devices.
Set all-in-one‘s signal source to the corresponding AV channel.
YPbPr (component)
Use the component audio and video cables to connect devices with component output function, note the
color of cables and socket are connecting correspondingly.
After connected the cable, turn on all-in-one, and audio and video devices.
Set all-in-one’s signal source to the corresponding component channel.
HDMI
Use an HDMI cable to connect external audio and video devices to the HDMI input port of all-in-one.
After connected the cable, turn on all-in-one and external audio and video devices.
Set all-in-one’s signal source to the corresponding HDMI channel.
You can also connect external audio and video devices to all-in-one’s front HDMI port; front HDMI
interface corresponding source is HDMI1, meanwhile HDMI signal automatically switch from the
built-in PC to the front port device.
Page 17
16
Audio output
Connect headphones or other audio devices to all-in-one’s audio output (headphone output) port.
After connected the cable, turn on all-in-one and external audio and video devices.
Coaxial output
Use a coaxial cable to connect the coaxial output to the audio device with coaxial input function.
After connected cables, open all-in-one and audio and video device.
AV output
Use AV audio and video cables to connect all-in-one’s AV output and devices with AV input function, yellow
for video, red for the right channel, white for the left channel.
After connected the cable, turn on all-in-one and audio and video devices.
Page 18
17
Note: Only in AV IN or TV channel, AV has output.
TV board AV output requires the use of 3.5mm AV adapter cable.
TV antenna connection
Connect the antenna or cable TV line to the TV's RF port.
After Connected the antenna, turn on all-in-one power, it is on.
Set all-in-one’s signal source to TV channel.
Enter the menu Tuning.
4KHDMI Port(this is only for the device with 4K port function)
4K HDMI Resolution Ratio Supported: 1920*1080 50Hz/60Hz
3840*2160 23Hz/24Hz/29Hz/30Hz
4096*2160 23Hz/24Hz/29Hz/30Hz
All-in-one’s video output
All-in-one’s PC module supports up to two screens to simultaneously display connected to a projector or
flat-panel TV via VGA and HDMI output interface of PC port. Because all-in-one has in-built one way
Page 19
18
HDMI, it can only simultaneously connect one way of external display device.
Menu operation
Enter the menu
In TV mode, press the Menu button to display the channel, video, sound, time, setting, lock. Press the"◄►
" key in the movement between the sub-menu items (highlighted) to select the desired menu item. Press"▲▼" or"
◄►" key to do the confirmation and adjust the value of the
each of specific sub-menu item.
Throughout the Menu operation, press the key“▲▼◄► ”
to move, press the Menu key to return, press the Enter key to
confirm, press the Escape key to exit.
Channel menu
Automatic station search
Press "▲▼" button to select Auto Tuning, press the "confirm"
button, there will be prompted to "connect the antenna and
Tuning”, press "◄" and choose YES, it starts auto search.
In station search, press the menu key to interrupt and exit,
it will automatically exit after the channel search is completed.
Page 20
19
Manual search
Manual Search
Storage Channel
Sound System DK
The current channel
Search
Fine tuning
Frequency MHz
●Save returns
menu
Press "▲▼" to select manual search, press the "confirm"
key to enter Manual Search.
In the pop-up window, press "▲▼" to select the setting
item, press the "◄►" key to do parameter settings, press
the red button on the left lower corner of the remote
control to save, press the Menu key to return.
Channel edit
Press "▲▼" button to select the channel editing, press the
"confirm" key to enter the menu.
Note: Only the current channel is at the state of "TV", the channel menu will appear, it cannot see the
channel menu at other channels.
Image mode
1. Press "▲▼" button to select the picture mode, press the
"OK" button to select and press menu key exit.
Image mode includes four models of standard, soft, user,
dynamic for choosing; on selecting the user mode of
image mode, the contrast, brightness, color, sharpness
can be set.
2. Contrast
Press "▲▼" button to select Contrast, press "◄► " to adjust the contrast.
3. Brightness
Press "▲▼" button to select Brightness, press "◄►" to adjust the brightness.
4. Color
Press "▲▼" button to select the color, press "◄►" to adjust color.
5. Sharpness
Press "▲▼" button to select Sharpness, press "◄►" to adjust Sharpness.
6. Hue
Press "▲▼" button to select the color, press the "OK" button to adjust the hue.
7. Color Temperature
Page 21
20
Press "▲▼" button to select the color temperature, press the "confirm" key to enter the selection menu, press "◄►
" to select, press the Menu key to exit.
8. Zoom Mode
Press "▲▼" button to select the zoom mode, press the "confirm" key to enter the selection menu, press "◄►" to
select, press the Menu key to exit.
9. Noise Reduction
Press "▲▼" button to select Noise Reduction and press "OK" to select key, press the Menu key to exit.
10. Screen
Press "▲▼" button to select the screen, press the "confirm" key to set, press the Menu key to exit.
11. Dynamic backlight
Press "▲▼" button to select the dynamic backlight, press the "confirm" key to set, press the Menu key to exit.
Note: The screen setting only appears in VGA channels, in VGA channels, the screen display appears
incomplete, offset, blur text, you can choose automatically adjust function under the screen menu , it is
not generally recommend for users to make change for other setting. Dynamic backlight setting is only
appeared for all-in-one with 3D function, and the user can be adjusted according to the actual function
of all-in-one.
Sound menu
1. Sound mode
Press "▲▼" button to select the sound mode, press the "confirm"
key to adjust.
2. 120Hz
Press "▲▼" button to select 120Hz, press "◄►" to set, press the
Menu key to return.
3. 500Hz
Press "▲▼" button to select 500Hz, press "◄►" to set, press the
Menu key to return.
4. 1.5KHz
Press "▲▼" button to select 1.5KHz, press "◄►" to set, press the Menu key to return.
5. 5KHz
Press "▲▼" button to select 5KHz, press "◄►" to set, press the Menu key to return.
6. 10KHz
Page 22
21
Press "▲▼" button to select 10KHz, press "◄►" to set, press the Menu key to return.
7. Balance
Press "▲▼" button to select the balance, press the "◄►" key to set; press the Menu key to return.
8. Automatic volume
Press "▲▼" button to select automatic volume, press the "confirm" key to do open and close settings.
9. Surround sound
Press "▲▼" button to select the surround sound, press the "Enter" key to do on and off settings.
10. Coaxial output
Press "▲▼" button to select the coaxial output, press the "confirm" to set, press the Menu key to return.
Time menu
1. Clock
Press "▲▼" button to select the clock, press the "confirm" key to
enter setup, press "◄►" to set up, press the Menu key to return.
2. Off time
Press "▲▼" button to select off time, press the "confirm" key to
enter setup, press "◄►" to set up, press the Menu key to return.
3. Boot time
Press "▲▼" button to select the boot time, press the "confirm" key to enter setup, press "◄►" to set up, press the
Menu key to return.
4. Sleep time
Press "▲▼" button to select the sleep time, press the "confirm" key to enter setup, press "◄►" to set up, press the
Menu key to return.
5. Auto standby
Press "▲▼" button to select automatic standby, press the "confirm" key to set, press the Menu key to return.
Setup menu
1. Menu language
Press "▲▼" button to select the menu language, press the
"confirm" key to enter the language selection menu, press
the "▲▼◄►" to select, press the Enter key to confirm,
Press the Menu key to return.
Page 23
22
2. Power-saving mode
Press "▲▼" button to select the power-saving mode, press the
"confirm" key to set, there are three states of high, medium and low, screen brightness will be a corresponding
change.
3. Reset
When you select "Reset", press "confirm" key and prompt if confirm or not? press "◄►" to choose whether reset or
not.
When not familiar with all-in-one menu settings and cannot be restored to normal, you can select Reset to default
settings.
4. Blue screen
Select the "blue screen", press "OK" button to select On or Off.
After the blue screen is opened, the menu background is blue; default is off.
Note: Only all-in-one with 3D function has the following features.
3D model
Before setting up this feature, please play 3D movies, then
press the menu to set.
When 3D movie playback, press "" to select 3D mode, press
the "confirm" key to enter, appear prompt of “Please bring
3D glasses", and press the "confirm" key to enter 3D mode
selection. (If you have the switch on the glasses, put the
battery; open the 3D and press keys to do pairing, for details, please refer to glasses instructions)
Press "▲▼" to select the 3D mode, the user can choose according to the film format on their view.
1. Side by side: left and right format, in the absence of 3D features
playback device, you can see it is a picture separated from the
middle and composed of the left and right side by side two nearly
identical images.
2. Top bottom: up and down format, in the absence of 3D features
playback device, you can see it is a picture separated from the
middle, composed of the upper and lower side by side of the two
nearly identical screens.
Page 24
23
3. Normal_2d: The 2D movies into 3D movie playback.
Press "Menu" key to return to the setup menu page.
Press the "Return" key to exit the menu operations.
3D settings
Press "▲▼" to enter 3D mode selection, the user can modify the
settings according to personal preference.
Press "▲▼" to select the option of "+10", press "◄►" to change
the value to change the depth of field.
This option of"0" is not adjustable for a user.
Press "▲▼" to select the option of "left", press "◄►" to change the left and right selection to change the
three-dimensional/3D effect.
Press "Menu" key to return to the setup menu page.
Press the "Return" key to exit the menu operations.
Lock menu
Press "▲▼"key to select system lock, input 4 digits password,
and its initial password is 0000.
1. Reset password
Press the Confirm key to enter to reset the initial password.
2. System lock
Press the Confirm key to select ON or OFF for system lock.
3. Input lock
Press the Confirm key to enter the settings, and press the "▲▼"key to select the input needed setting, press the "
◄►"key to lock or unlock the input settings.
4. Channel lock
Press the Confirm key to enter the settings, and press the "▲▼"key to select the channel needed setting, press the
"◄►"key to lock or unlock the channel settings, locked channel will mark with the emergence of a lock, the
channel list needs to advance search or edited.
Enter multimedia status
Press the source button on the remote control, or USB keyboard
shortcut, select Multimedia.
Page 25
24
Press "◄►"key to switch among pictures, music, movies and text, press the Enter key to enter.
Picture play
Insert the USB storage device into the USB port. Enter the
"Picture", select C, press "OK" to enter the sub-menu.
1. Press "◄►" and "▲▼" to select the picture browsing,
picture is under preview state at this time, press the
"confirm" key to select.
2. Press "► " on the remote control to play the selected
picture, and then press pause. Press " ◄◄ " button
to play the previous piece, press the "►► " to play
the next, you can also press the confirm key, and in
the pop-up menu, you can select pause, play and other functions to operate.
3. Press the "Exit" button to exit.
Tip: When playing pictures, there is a capture feature in the pop-up menu; personal favorite pictures
can be set to the all-in-one's boot LOGO.
Music player
Insert the USB storage device into the USB port. Enter the
"Music", select C, press "OK" to enter the sub-menu.
1. Press "◄►" and "▲▼" to select music preview, the
music is in preview mode at this time, press the
"confirm" key to select.
2. Press"► " to play on the remote control, press
the pause. Press " ◄◄ " button to play the previous, press"►► " to play the next, you can then select the
Page 26
25
pause in the menu at the lower screen to operate play and other functions.
3. Press the "Exit" button to exit.
Movie player
1. Insert the USB storage device into the USB port.
2. Enter the "movie", select C, press "OK" to enter the
sub-menu.
3. Press the "◄►" and "▲▼" key to preview the movie
file you want to play, then the movie is in preview mode, press the "OK" button to select the movie file you
want to play.
4. Press the "► " key on the remote control to play, press the " ◄◄" key to play the previous, press "►► " to
play the next one, you can select pause in the menu at the lower screen to operate play and other functions.
5. Press the "Exit" button to exit.
Text player
Insert the USB storage device into the USB port .Enter the
"text", select C, press "confirm" to enter sub-menu.
1. Press "◄►" and "▲▼" to select text preview, then the text is in preview mode, press the "confirm" key to
select.
2. Press "► " on the remote control to play.
3. Press the confirm key, you can select Previous/ Next
to do flip operation in the menu at the lower screen,
and select music function, it would background play
music files of the USB memory while browsing the text.
4. Press the "Exit" button to exit.
Page 27
26
Installation & Using of touch screen software
1. Load the attached disk into CD-ROM
2. Double-click to run “TouchDevSetup.exe” i
n the disc.
3. Complete installation accordingly.
4. Click “ Finish ” and run touch screen
management application “Fitouch.exe”. The
installation will be completed till to
shows up at right corner of desk top。
Note:
blue shows the equipment has been connected
gray shows the equipment has not been
connected or failed connection
1. Run TouchDev.exe
By default, the software will automatically execute, the icon can
be found at the right corner of desk top.
If the software is closed carelessly, operate “start up” ->
“program”, to find out“TouchDev”, and select “touchdev”,
then run it. By default, shortcut of“touchedv” is on desktop,
double click it.
2. Main Menu
Click the icon of“TouchDev”, there will pop up the main menu
as left figure. Its functions are listed as follows:
Language: select relevant language for interface.
Calibration: conduct screen calibration, to make sure the touch
place correspond to the real location of the screen.
Options: showing basic information of touch screen, allocate
relevant parameters for real requirement, for better effect.
（Ⅰ）Setup
The software will be updated, please turn to your dealer for new version.
（Ⅱ）Basic function
Page 28
27
About: show some information of TouchDev.
Exit: close TouchDev.
3. Calibration:
Normal calibration standards:
As showed in the left picture, there are “custom made” and
“advanced” for calibration. If the two options are not selected,
it is normal model of calibration. This model fits for the case of
connecting only one piece of electronic white board.
“ positioning model ” includes “ touch screen ” and
“electronic white board”, being different at “electronic white
board” supports positioning of non-rectangle screen, and
“touch screen” only supports positioning of rectangle screen.
For screen adopting projector, take “electronic white board”
model.
“positioning location” has two kinds of “1”and “2”, the
first one the icon display is close to the 4 angles of the screen,
the second one the icon display is close to the center of the
screen. (Note: generally, the first one is suggested.)
4. Screen calibration：
After selection, click “calibration”, then appears the interface
as on the left, use touch pen or by hand to touch the center of
icon“ ”. (in the process of positioning, the touch pen must be
vertical to the screen surface, and pen point coincide with the
center of icon “ ”.)
The positioning icon will move to the 4 angles of the screen by
touch. For “electronic white board” model, the icon will also
appear in the center of the screen.
Custom-made calibration:
When select “custom-made”, it is custom made model. It
supports two kinds of positioning, “custom made” model –
need connecting two pieces of electronic white boards at the
same time, in the case of one piece of board, it does not support
custom made model.
Page 29
28
2）matching between two pieces of screen: Referring that the
screen is cut into two pieces, with separate performance on both
pieces at the same time, and both pieces of screen all need touch
screen. In this case, it need two times of positioning, the first
time is on the left, and the second is on the right.
5. Options：
information:
“basic” box shows some information on the present screen, in
the case of matching many pieces of touch screens, different
screens can be numbered to show specific information on
related screen.
“features” box shows some updated information of touch
screen, “√” is supporting, “×”is not supported.
Upgrading method: (related authorized documents are needed
before upgrading.)
Click “×” in“features” will see the upgrading box:
Click “upgrade” to seek for the authorized documents for
upgrading.
6. Configuration：
For “service parameters” configuration, it is suggested to use
default value, unless there is necessary requirement. Description
to parameters: right is starting up or not: select “Yes” to use
right button; select “No”, the right button is closed.
Delayed time length: set the time length to emerge right button
accident.
Fault-tolerant space: there will be error while pressing on the
screen by hand, errors in some range is permitted, and count
these errors as on point to emerge right button accident.
Sleek coefficient: average many a sampling point, to make sure
data points sent to the system is smooth that is the scribing line
is not vibrating very large.
Page 30
29
（Ⅲ）Basic operation
General
operation
The customer could realize the following operations on the screen:
Click------object on the screen
Double click------click the same object twice quickly on the same screen
Drag------press the object and drag it
Right key------press the object and remain for 2-3 second
Item
OPS
Motherboard
Mini ITX architecture，Intel H81 chipset
CPU
Intel1150 interface Pentium，I3, I5, I7 models, refer to real product（below 65W）
Graphics card
Integrated graphics card Intel® HD Graphics, 4600 supporting 4K,2K
Memory
DDRIII1600 / 2G / 4G, refer to real product
Hard disk
SATA2.5” 500G
WIFI
Supports IEEE802.11b / g / n, rate 150,300Mbps, maximum 100 meters indoor coverage to
support security encryption, configuration is optional
Bluetooth
Support Bluetooth standard V3.0 + EDR, the highest rate of 3Mbps, the effective distance of 10
meters, configuration is optional
Please see related documents for detailed in the discs attached with all-in-one.
The content related with hardware installation & connection is only specific to the products without built-in
computer.
Computer specifications
Page 31
30
Touch screen size
Touch technology
Non-contact infrared sensor technology
Sensing objects
Opaque objects (such as a finger, pen, etc.)
Effective Touch Size
≥ Ø5mm
Multi-point support
2, 4 points
Response time
Single-point mode: Click: 13ms continuous: 3ms
Multi-point mode: Click: 13ms continuous: 5-10ms
Two points simultaneous touch: Continuous 10ms
Cursor speed
Up to 300 points / second
Coordinate output
32768x32768
Positioning accuracy
≤±2mm
Touch screen glass
4mm, physical steel Moths 7 explosion, light transmittance:
Life
Unlimited service life
Simple trouble eliminating
All in one cannot work normally
(1)Remote control malfunction.
(2) All-in-one automatically shutdown.
Check power cable whether connect well.
Check whether it have set sleep.
Check whether has signal to input.
Check the key board in front of all in one whether there is obstruction to lead to automatic close backlight of
(3) All in one display no signal.
Check Signal input device to all in one whether the connection is correct.
Check the signal source of all in one whether is correct.
Check the remote control between the TV remote control receiving windows whether there are any objects
blocking, and lead to the remote control failure.
Check the battery in remote control whether have install well or need to be replaced.
Check whether it is in the range of all in one to remote control operation.
all- in -one .
Page 32
31
Built in PC pattern
(1) Signal without full screen or beyond the scope.
Check the resolution whether it is the best resolution.
Check the image zooming mode whether it is correct.
(2) Image shift.
In the menu image set to select automatic calibration.
(3) Image miss color, incorrect color.
Check VAG cable whether connect well or damaged.
Check whether image mode is default in the menu.
Check the setting of PC display output is correct.
(4)Display does not support the format.
In the menu to choice for automatic scaling, and calibration.
Touch function
(1)Touch function invalid.
Confirm whether use random fringe touch pen and considerable size object or finger to operate.
Use check tool to check touch screen AD whether have red or blue words.
(2)Touch position is not accurate.
Recalibrate touch screen.
Check whether touch pen is on touch screen while check calibration.
Audio function is working or not
(1)Have image without sound.
Check if all in one is in silent mode.
Increase the volume.
Check audio cable is correct connected.
Check the output device of PC sound card is correct.
(2)Just one side speaker has sound.
Adjust the sound balance in the menu.
Check the PC voice control panel whether is only set up a sound channel.
Check if audio cable is connected well.
Page 33
32
Maintenance
Proper maintenance can prevent much early failure; regular cleaning can avoid affecting normal use, also influence
display and perfect appearance.
Clean screen
Using a soft cloth to gently wipe the dust on the screen.
Avoid larger strength to repeated cleaning .In order to avoid scratches or damage glass.
If dry cloth hard to erase heterogeneities, and can dip little water and neutral detergent, banning to use
organic solvents.
Be careful not to squeeze water into the machine.
Cleaning surface frame
Use a dry, soft cloth to wipe the front frame, and pay attention to check and prevent foreign objects into the
frame scratching.
Clean all-in-one’s joint place between glass sides and front frame to avoid the accumulation of dust or other
foreign matter.
Don’t use for long time
Don’t use all in one for long time, please remove the plug and take out the battery of remote control.
Note: this manual according to existing products specification, due to the demand of products improve
continuously, So we reserve the right to modify relevant parameters and no future notice.
Loading...