Questions, problems, missing parts? Contact the customer service department at
1-866-994-4148, 8 a.m. - 6 p.m., EST, Monday - Thursday, 8 a.m. - 5 p.m., EST, Friday.
ITEM #0333554, #0333553
MODEL #GU8813-BZ-I, #GU8813-WH-I
DUSK-TO-DAWN
LIGHT
Français p. 7
Español p. 13
ATTACH YOUR RECEIPT HERE
AB13436
Serial Number: Purchase Date:
Utilitech & UT Design® and Grounded in Quality® are
registered trademarks of LF, LLC. All Rights Reserved.
Lowes.com
1
PACKAGE CONTENTS
HARDWARE CONTENTS (shown actual size)
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with
package contents list and diagram above. If any part is missing or damaged, do not attempt to
assemble the product. Contact customer service for replacement parts.
Wire Nut
Qty. 3
AA
SAFETY INFORMATION
WARNING
• Shut off power at the circuit breaker or fuse panel before removing the old fixture or
installing the new one.
CAUTION
• DO NOT USE THIS FIXTURE WITH A DIMMING CIRCUIT. If you presently have dimmer controls,
you will need to remove them, and replace them with regular electrical switches. If you have a three-
way dimmer, you will have to replace it with a regular three-way switch. If you are unfamiliar with
electrical installations, it is recommended you have a qualified electrician do your installation.
Hg
LAMP CONTAINS MERCURY
Manage in accordance with disposal laws.
www.lamprecycle.org
1-866-666-6850
Qty. 2
Machine
Screw
BB
A
B
C
D
Qty. 1
Finial
Cap
CC
Qty. 1
Mounting
Bracket
EE
(Not shown to size)
(Not shown
to size)
Qty. 1
Threaded
Tube
DD
Qty. 1
Grounding
Screw
FF
A Fixture 1 C Bulb 1
PART DESCRIPTION QUANTITY PART DESCRIPTION QUANTITY
B Diffuser 1 D Dusk-to-Dawn Sensor 1
Lowes.com
2
With power disconnected to your electrical box, remove the old fixture. If your old fixture is attached to
an electrical box having more than two (2) wire leads, it is recommended you use tape and markings
to keep track of which wires were attached to each other.
ASSEMBLY INSTRUCTIONS
PREPARATION
Estimated Assembly Time: 45 minutes
Tools Required for Assembly (not included):
Flathead Screwdriver, Safety Glasses, Electrical Tape
Phillips head Screwdriver, Wire Cutters, Pliers, Wire Strippers, Step Ladder, Level
.
1
2
3
Machine
Screw
BB
x 2
Hardware Used
Mounting
Bracket
x 1
EE
Hardware Used
Mounting
Bracket
x 1
EE
EE
1.
Position the elongated holes in the mounting
bracket (EE) over the electrical box ears and attach
the mounting bracket (EE) onto the electrical box
using either the original screws from the electrical box
or the machine screws (BB) (Fig. 1). NOTE: The
included mounting bracket (EE) may be slightly
different. The mounting bracket (EE) may mount
vertically, diagonally or horizontal.
2.
Screw the threaded tube (DD) into the center hole of
the mounting bracket (EE), leaving approximately 1/2
in. of the threaded tube (DD) protruding beyond the
front surface of the mounting bracket (EE) (Fig. 2).
3. For safety and proper operation, your fixture must be
properly grounded (Fig. 3). If you are unfamiliar with the
methods of properly grounding your fixture, consult a
qualified electrician. A copper ground wire is
pre-attached to your fixture pan (A). If your electrical
box is made of plastic and/or has a green or bare
copper grounding wire inside, the fixture grounding wire
and the electrical box ground wire should be connected
together using one of the wire nuts (AA). If your
electrical box is made of metal and is already grounded,
secure the bare end of the fixture ground wire to the
mounting bracket (EE) using the ground screw (FF) on
the mounting bracket (EE).
BB
DD
EE
BB
EE
FF
Threaded
Tube
DD
x 1
Hardware Used
Grounding
Screw
FF
x 1
Lowes.com
3
ASSEMBLY INSTRUCTIONS
4. Connect the supply leads from the electrical box to the
fixture wire leads using the wire nuts (AA) (Fig. 4). The
black lead from the fixture pan (A) is spliced to the black
supply lead, and the white lead from the fixture pan (A) is
spliced to the white supply lead. Make sure the wire nuts
(AA) are tight. You can wrap electrical tape around the
wire nuts (AA) to prevent them from coming loose.
Carefully push the spliced wires back into the electrical
box.
5.
Position the fixture pan (A) over the electrical box so
that the threaded tube (DD) protruding from the
mounting bracket (EE) passes through the hole in the
back of the fixture pan (A). Secure the fixture pan (A) to
the electrical box with the finial cap (CC) (Fig. 5). Make
sure the fixture pan (A) is level. The fixture pan (A)
should be tight up against the wall surface.
6.
Grasp the bulb (C) by the plastic base, and align the
pins on the bulb (C) with the socket (Fig. 6). Rotate the
bulb (C) clockwise approximately
1
/4
turn until the bulb
(C) base is secure in the socket.
7. Push the diffuser up, apply sufficient pressure to it
and rotate it clockwise until it screws in securely to the
pan (Fig. 7).
Restore power to the electrical box to make sure your
fixture is working properly.
AA
A
AA
CC
DD
C
A
CC
Finial
Cap
x 1
Hardware Used
Threaded
Tube
DD
x 1
4
5
7
AA
Wire Nut
Hardware Used
x 2
A
B
C
6
Lowes.com
4
C
A
You may want to periodically clean the fixture using a mild, non-abrasive glass cleaner and soft
cloth. Do NOT use solvents or cleaners containing abrasive agents. When cleaning the fixture,
make sure you have the power turned off and do not spray liquid cleaner directly onto the bulb,
socket, ballast, or wiring.
CARE AND MAINTENANCE
1
2
ASSEMBLY INSTRUCTIONS
1. While holding the diffuser (B) in the palm of your hand(s), rotate it counterclockwise until it
unscrews from the fixture (A).
This fixture uses one (1) GU24 CFL13W self-ballasted fluorescent bulb. These bulbs are readily
available at your local home center, and most larger hardware stores.
Before replacing bulb (C), shut off power to the fixture at the circuit breaker or fuse panel. Allow
sufficient time for fixture and lamp to cool.
4. Dispose of the old lamp(s) in accordance with local, state, and/or federal laws, or go to
www.lamprecycle.org for more information.
2. Remove the defective bulb by grasping it by the
plastic base and unscrewing it from the bulb socket 1/4
turn in counterclockwise direction (Fig. 1).
3. Install the new bulb in the same manner you
removed the old bulb. Reattach the diffuser (B)
following the same instructions in Step 2, except screw
the diffuser (B) onto the fixture (A) in a clockwise
direction. Make sure the diffuser is fully attached onto
the fixture (A) before releasing your hands. Restore
power to the fixture (A).
BULB REPLACEMENT INSTRUCTIONS
Minor problems often can be fixed without the help of an electrician. Before doing any work on the
fixture, shut off power supply at the circuit breaker panel to avoid electrical shock.
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
Fixture doesn’t light.
Circuit breaker trips
when light is turned on.
1. Power is off.
2. Bad wire connection.
3. Defective bulb(s).
4. Defective wall switch.
1. Crossed wires or power wire
is grounded out.
1. Check circuit breaker or wall switch.
2. Check wire splices.
3. Replace bulb(s).
4. Replace switch.
1. Check wiring connections.
8.
In the event of outdoor installation, you will need to
use silicon or other waterproof caulk around the outer
perimeter of the fixture (A) pan to prevent water seeping
into the wiring compartment (Fig. 8).
This fixture (A) is equipped with a dusk-to-dawn sensor
(D). In order to test the fixture (A) during daylight hours,
the electrical switch to the lantern must be turned ON,
and the lens of the photo sensor (D) must be covered
using an opaque material to block the light. Since the
dusk-to-dawn sensor (D) controls the ON/OFF cyle of
the fixture (A), the wall switch controlling the fixture (A)
must be left ON at all times.
8
A
B
Lowes.com
5
REPLACEMENT PARTS LIST
WARRANTY
For replacement parts, call our customer service department at 1-866-994-4148, 8 a.m. - 6 p.m., EST,
Monday - Thursday, 8 a.m. - 5 p.m., EST, Friday.
PART DESCRIPTION PART #
AA Wire Nut HDW8813
BB Machine Screw HDW8813
CC Finial Cap HDW8813
DD Threaded Tube HDW8813
EE Mounting Bracket HDW8813
FF Green Ground Screw HDW8813
AA
AA
BB
AA
BB
DD
FF
EE
CC
Printed in China
Utilitech & UT Design® and Grounded in Quality® are
registered trademarks of LF, LLC. All Rights Reserved.
Lowes.com
6
The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship
for a period of (3) years from the date of original purchase by the consumer. We will repair or replace
(at our option) the unit in the original color and style if available, or in a similar color and style if the
original item has been discontinued, without charge. The manufacturer warrants the lamp for 3 years,
providing the lamp is not used in a commercial application where it is on 24 hours per day, but is
used in a residential environment for 3 - 5 hours per day. Defective units must be properly packed
and returned to the manufacturer with a letter of explanation and your original purchase receipt
showing date of purchase. Call 1-866-994-4148 to obtain a return authorization number and an
address where to ship your defective product. Note: No C.O.D. shipments will be accepted. The
liability of the manufacturer is in any case limited to replacement of the defective light fixture product.
The manufacturer will not be liable for any other loss, damage, or injury which is caused by the
product. This limitation upon the liability of the manufacturer includes any loss, damage, or injury
which is (I) to person or property or otherwise; (II) incidental or consequential in nature; (III) based
upon theories of warranty, contract, negligence, strict liability, tort, or otherwise; or (IV) directly, or
indirectly related to the sale, use, or repair of the product. This warranty gives you specific rights, and
you may also have other rights which vary from state to state.
Loading...