ITEM #0756347, #0756348
MODEL #SE1056-WHG-01LF0-U,
SE1056-BRS-01LF0-U
DUSK-TO-DAWN
LED LIGHT
Français p. 7
Español p. 13
ATTACH YOUR RECEIPT HERE
AB15812
Serial Number: Purchase Date:
Utilitech & UT Design® and Grounded in Quality® are
registered trademarks of LF, LLC. All Rights Reserved.
Questions, problems, missing parts? Contact the customer service department at
1-866-994-4148, 8 a.m. - 6 p.m., EST, Monday - Thursday, 8 a.m. - 5 p.m., EST, Friday.
Lowes.com
1
PACKAGE CONTENTS
HARDWARE CONTENTS (shown actual size)
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with
package contents list and hardware contents list. If any part is missing or damaged, do not
attempt to assemble the product.
Estimated Assembly Time: 45 minutes
Tools Required for Assembly (not included):
Electrical Tape,
Phillips Screwdriver, Flathead Screwdriver, and Silicone Sealant.
Wire Nut
Qty. 3
AA
A Fixture 1 C
D
Dusk-to-Dawn Sensor
Grounding Wire
1
1
PART DESCRIPTION QUANTITY PART DESCRIPTION QUANTITY
B Diffuser 1
Qty. 1
Sensor
Cap
HH
Qty. 1
Sensor
Hood
GG
Qty. 2
Machine
Screw
CCBB
Mounting Bracket
(not actual size)
Qty. 1
C
B
A
Qty. 1
Threaded
Hollow Tube
DD
Qty. 1
Mounting
Cap
FF
SAFETY INFORMATION
WARNING
• Shut off power at the circuit breaker or fuse panel before removing the old fixture or
installing the new one.
• LEDs can be damaged by electrostatic discharge (ESD) shock. Before installation, discharge
yourself by touching a grounded bare metal surface to remove this hazard. To avoid damage,
do not remove the clear lens over the LED module.
• This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
CAUTION
• DO NOT USE THIS FIXTURE WITH A DIMMING CIRCUIT. If the fixture is being wired to a switch that
has dimmer controls, the dimmer switch will need to be replaced with a standard electrical switch. If a
three-way dimmer is currently installed, it will need to be replaced with a standard three-way switch. If
unfamiliar with electrical installations, it is recommended a qualified electrician do the installation.
D
Qty. 1
Grounding
Screw
EE
Lowes.com
2
1.
Screw the threaded tube (DD) to the mounting bracket
(BB). Leave approximately 1 in. of the threaded tube
protruding beyond the front surface of the mounting
bracket.
2. Using (2) machine screws (CC), attach the mounting
bracket (BB) to the electrical box. Pull the existing
electrical supply wires out of the box to either side of
the mounting bracket.
3.
For safe and proper operation, the fixture (A) must be
properly grounded. If the electrical box is made of
metal, and is already grounded, secure the bare end
of the fixture green/copper ground wire to the
mounting bracket (BB) using the green grounding
screw (EE). If the electrical box is a non-grounded
type, or made of plastic, connect both the fixture
green/copper ground wire AND the green/copper
ground wire inside the electrical box to the mounting
bracket (BB) using the green grounding screw (EE).
If unsure whether or not the electrical box is properly
grounded, or the box is plastic and has no ground
wire, or are unfamiliar with the methods of properly
grounding the fixture, consult a qualified electrician.
With power disconnected to the electrical box, remove the old fixture. If the old fixture is attached to
an electrical box having more than two (2) wire leads, use tape and markings to keep track of which
wires were attached together.
ASSEMBLY INSTRUCTIONS
Mounting
Bracket
BB
BB
x 1
Hardware Used
Threaded
Hollow Tube
DD
DD
x 1
Machine
Screw
CC
x 2
Hardware Used
AA
Wire Nut
Hardware Used
x 1
EE
Grounding Screw
x 1
1
Mounting
Bracket
BB
x 1
2
3
AA
EE
BB
D
A
BB
CC
CC
Lowes.com
3
ASSEMBLY INSTRUCTIONS
4. M
ake connections on the back side of the fixture.
Connect the supply lead wires from the electrical box
to the fixture lead wires using the wire nuts (AA). The
black lead from the fixture (A) is spliced to the black
supply lead, and the white lead from the fixture (A) is
spliced to the white supply lead. Ensure the wire nuts
(AA) are tight. Wrap electrical tape around the wire
nuts (AA) to prevent them from coming loose.
Carefully push the spliced wires back into the electrical
box.
5.
Position the fixture over the electrical box so that the
threaded tube (DD) attached to the mounting bracket
passes through the mounting hole in the fixture.
Carefully, hand tighten the mounting cap (FF) and
secure the fixture to the mounting bracket, while
leveling up the fixture during the tightening process.
Ensure the fixture is level prior to fully tightening it
firmly against the surface. Overtightening the fixture
could result in damage to the fixture.
3
AA
Wire Nut
Hardware Used
x 2
FF
Mounting Cap
Hardware Used
x 1
4
AA
AA
5
A
FF
DD
FF
2
6.
In the event of outdoor installation, a silicone or other
waterproof sealant around the outer perimeter of the
fixture (A) is needed to prevent water from seeping
into the wiring compartment.
6
A
Lowes.com
4
CARE AND MAINTENANCE
1
2
OPERATING INSTRUCTIONS
GG
Sensor Hood
Hardware Used
x 1
HH
Sensor Cap
Hardware Used
x 1
C
C
1
Minor problems often can be fixed without the help of an electrician. Before doing any work on the
fixture, shut off power supply at the circuit breaker panel to avoid electrical shock.
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
Fixture doesn’t light.
Fuse blows or circuit
breaker trips when light
is turned on.
1. Power is off.
2. Bad connection.
3. Bad switch.
4. Photo sensor is inactive.
1. Discontinue use.
1. Check if power supply is on.
2. Check cords and/or wiring.
3. Test or replace switch.
4. Cap sensor or wait until dark.
1. Call customer service.
1. If fixture repeatedly cycles ON and OFF at night, the
dusk-to-dawn sensor (C) may be activating erratically
due to light reflecting off a nearby surface. Place the
sensor hood (GG) firmly over the dusk-to-dawn sensor.
This should prevent extraneous light from ‘tripping’ the
dusk-to-dawn sensor (C).
This fixture is controlled by a dusk-to-dawn photo light sensor (C). For the fixture to work properly, the
wall switch controlling the power to the fixture MUST be turned ON at ALL times.
2.
To disable the dusk-to-dawn sensor (C), install the
sensor cap (HH) over the dusk-to-dawn sensor (C). This
will prevent the dusk-to-dawn sensor (C) from controlling
the ON/OFF function, and will allow the ON/OFF function
to be directly controlled by the wall switch.
GG
HH
Periodically clean the fixture using a mild, non-abrasive glass cleaner and soft cloth. Do NOT use
solvents or cleaners containing abrasive agents. When cleaning the fixture, make sure the power is
turned off. Do not spray liquid cleaner directly onto the LEDs, fixture, diffuser, or wiring.
Lowes.com
5
WARRANTY
The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a
period of (5) years from the date of original purchase by the consumer. The fixture is not warrantied for
use in a commercial or retail application. The warranty is limited to use in a residential environment. We
will repair or replace (at our option) the unit in the original color, and style if available, or in a similar color
and style if the original item has been discontinued, without charge. Defective units must be properly
packed and returned to the manufacturer with a letter of explanation and your original purchase receipt
showing date of purchase. Call 1-866-994-4148 to obtain a Return Authorization Number and an address
where to ship your defective product. Note: C.O.D. shipments will NOT be accepted. The liability of the
manufacturer is in any case limited to replacement of the defective light fixture product. The manufacturer
will not be liable for any other loss, damage, labor costs or injury which is caused by the product. This
limitation upon the liability of the manufacturer includes any loss, damage, or injury which is (I) to person
or property or otherwise; (II) incidental or consequential in nature; (III) based upon theories of warranty,
contract, negligence, strict liability, tort, or otherwise; or (IV) directly, or indirectly related to the sale, use,
or repair of the product. This warranty gives you specific rights, and you may also have other rights which
vary from state to state.
REPLACEMENT PARTS LIST
For replacement parts, call our customer service department at 1-866-994-4148, 8 a.m. - 6 p.m., EST,
Monday - Thursday, 8 a.m. - 5 p.m., EST, Friday.
PART DESCRIPTION PART #
B Diffuser ZD-SE1056F01
GG Sensor Hood ZH-SE1056F01-WHG, ZH-SE1056F01-BRS
HH Sensor Cap ZH-SE1056F01-WHG, ZH-SE1056F01-BRS
HH
GG
Printed in China
Utilitech & UT Design® and Grounded in Quality® are
registered trademarks of LF, LLC. All Rights Reserved.
B
Lowes.com
6
Loading...