UTC Fire and Security Americas RS3130 User Manual

UltraSync Wi Fi IP Camera
Installation Guide

P/N 466-5236 • REV B • ISS 28APR16 © 2016 United Technologies Corporation. All rights reserved 1

Contents

Installation environment ...........................................................3

Package contents ....................................................................4

Cable requirements .................................................................6

Camera description .................................................................7

Accessing the SD card ............................................................8

Wedge Camera .....................................................................9

Desktop Camera ...................................................................9

Mounting the Wedge Camera ................................................ 10

Mounting the Desktop Camera .............................................. 13

Quick Setup ........................................................................... 16

Setting up Ethernet/Wi Fi transmission .................................. 16

Wi Fi Signal Strength ............................................................. 17

Add Cameras to a Wi Fi Network ........................................... 18

Add Cameras to UltraSync .................................................... 19

Reboot Cameras ................................................................... 20

View Live Stream and Latest Clip .......................................... 20

Program Event Triggered camera clips .................................. 21

Change Default Camera Settings ........................................... 26

Alternatives for Adding Cameras............................................ 27

via Wi Fi (using Windows PC for setup) ............................... 27

via Ethernet (non-DHCP, using iOS Device for setup) .......... 27

via Ethernet (non-DHCP, using Windows PC for setup) ....... 28

Troubleshooting ..................................................................... 29

Specifications ........................................................................ 31

2 P/N 466-5236 • REV B • ISS 28APR16 © 2016 United Technologies Corporation. All rights reserved

Installation environment

When installing your product, consider these
factors:

• Electrical: Install electrical wiring carefully. It should be done by
qualified service personnel. Always use a proper PoE switch or
a 12 VDC UL listed Class 2 or CE certified power supply to
power the camera. Do not overload the power cord or adapter.

• Ventilation: Ensure that the location planned for the installation
of the camera is well ventilated.

• Temperature: Do not operate the camera beyond the specified
temperature, humidity or power source ratings. The operating
temperature of the camera is between -30 to +60°C (-22 to
140°F). Humidity is below 90%.

• Moisture: Do not expose the camera to rain or moisture, or try
to operate it in wet areas. Turn the power off immediately if the
camera is wet and ask a qualified service person for servicing.
Moisture can damage the camera and also create the danger of
electric shock.

• Servicing: Do not attempt to service this camera yourself. Any
attempt to dismantle or remove the covers from this product will
invalidate the warranty and may also result in serious injury.
Refer all servicing to qualified service personnel.

• Cleaning: Do not touch the sensor modules with fingers. If
cleaning is necessary, use a clean cloth with some ethanol and
wipe the camera gently. If the camera will not be used for an
extended period of time, put on the lens cap to protect the
sensors from dirt.

P/N 466-5236 • REV B • ISS 28APR16 © 2016 United Technologies Corporation. All rights reserved 3

Package contents

Transformer

Check the package and contents for visible damage. If any
components are damaged or missing, do not attempt to use the
unit; contact the supplier immediately. If the unit is returned, it must
be shipped back in its original packaging.

UltraSync Wi Fi IP Wedge Camera

4 P/N 466-5236 • REV B • ISS 28APR16 © 2016 United Technologies Corporation. All rights reserved

Power Supply (US)

UltraSync Wi Fi IP Desktop Camera

P/N 466-5236 • REV B • ISS 28APR16 © 2016 United Technologies Corporation. All rights reserved 5

One power supply with interchangeable plugs is included for SKU

Power Supply (EU)

Power Supply (UK)

Power Supply (AUS)

number RS-3131.

CAUTION: Use direct plug-in UL listed power supplies marked
Class 2/CE certified or LPS (limited power source) of the required
output rating as listed on the unit.

Risk of explosion if battery is replaced by an incorrect type.
Dispose of used batteries according to the instructions.

Cable requirements

For proper operation, adhere to the following cable and power
requirements for the cameras. Category 5 cabling or better is
recommended. All network cabling must be installed according to
applicable codes and regulations.

6 P/N 466-5236 • REV B • ISS 28APR16 © 2016 United Technologies Corporation. All rights reserved

Camera description – Wedge Camera

9

2

1

6

8

7

3

5

4

1

0

1

1

1. Camera cover/housing

2. Lens

3. SD card

4. Ethernet RJ45 PoE port

5. Power supply

6. Base

7. Alarm and Audio port

8. Reset/WPS button

9. Converter pan

10. Antenna

11. Microphone

P/N 466-5236 • REV B • ISS 28APR16 © 2016 United Technologies Corporation. All rights reserved 7

Camera description – Desktop Camera

1. Lens

2. Microphone

3. IR LED

4. PIR

5. Light sensor

6. SD card slot

7. Bracket stand

8. RJ45 network port

9. WPS/RET button

10. Alarm I/O

11. DC12V port

8 P/N 466-5236 • REV B • ISS 28APR16 © 2016 United Technologies Corporation. All rights reserved

Accessing the SD card

Wedge Camera

An 8GB Micro SD card is pre-installed with the camera; (see item 3
in Camera Description, page 6).

Desktop Camera

An 8GB Micro SD card is pre-installed with the camera.
If desired, the Micro SD Card can be replaced with up to 64GB for

local storage as a backup in case, for example, the network fails.

Note: Video and log files stored on the Micro SD card can only be
accessed via the UltraSync App when validated with the UltraSync
Panel.

P/N 466-5236 • REV B • ISS 28APR16 © 2016 United Technologies Corporation. All rights reserved 9

Mounting the Wedge Camera

A

To mount the wedge camera on a wall or ceiling:

1. Drill the holes for the mounting hardware in the mounting
surface using the supplied drill template. To route the cables
from the base of the camera, drill a cable access hole in the
mounting surface.

2. Mount the converter pan to the mounting surface (optional).

Note: If required, you can remove the tab (A) on the side of
the converter pan to pass the cables through.

10 P/N 466-5236 • REV B • ISS 28APR16 © 2016 United Technologies Corporation. All rights reserved

3. Loosen the screws with
the tamper-resistant hex
wrench (supplied) to
remove the camera cover.

4. Mount the camera base to
the converter pan or
mounting surface,
depending on the
installation.

5. Use the supplied lens
alignment tool to adjust
the pan [±30°], tilt
[0 to 80°], and rotation

direction [0 to 360°].

Tilt

Pan

Adjusting
Tool

Rotation

P/N 466-5236 • REV B • ISS 28APR16 © 2016 United Technologies Corporation. All rights reserved 11

6. Re-attach the dome
cover to the camera.

Wedge Camera Dimensions

Wedge Camera Mounting Plate Dimensions

12 P/N 466-5236 • REV B • ISS 28APR16 © 2016 United Technologies Corporation. All rights reserved