UTC Fire and Security Americas 958 BTWI User Manual

AdvisorOne Bluetooth® Wi-Fi® Installation Sheet

EN

CNF

ES

PR

1. Bluetooth Wi-Fi Module

2. AdvisorOne Panel (With Covers Installed)

3. AdvisorOne Panel (With Covers Removed)

English: Installation Sheet

Description

The Advisor™One self-contained lifestyle management and security system detects situations and provides control and information
to home and small business owners (P/N AVO-1037).

This document provides instructions on installing and programming the AdvisorOne Bluetooth Wi-Fi module (P/N AVO-BTWIFI) for
use with the AdvisorOne panel.

The AdvisorOne Bluetooth Wi-Fi module extends the capability of interfacing with the AdvisorOne system. The module’s Wi-Fi
capability enables wireless Ethernet connections to a router and/or provides wireless Ethernet connection to touchscreens and IP
cameras. The module’s Bluetooth capability enables mobile device access and control.

Preparation and Installation

Preparing to Install the Bluetooth Wi-Fi Module

WARNING: Use caution when installing or removing the power supply to an outlet with a metal cover.

1. Depending on the situation, it may be necessary to contact the central monitoring station before starting the installation.

2. If power supply is present, remove the screw from the securement tab and unplug the power supply.

3. Remove the screw securing the panel chassis. Open the panel by pressing down on the tabs and carefully swing the panel
chassis open.

P/N 466-4408 • REV C • 23APR15 1 / 6

CAUTION: Use static electricity precautions when handling electronic components.

Installation

Action

Note

US

Plug the power supply into the outlet and secure with the supplied screw.

Canada

Plug the power supply into the outlet.

Do not use the securement tab and screw.

All Other Installations

Follow regional requirements.

Option

Description

Name

Change the name of the Wi-Fi WAN interface. Optional, not recommended.

Line Fault

Sets the condition that if Wi-Fi connection fails, if the panel treats the loss as a fault or ignores it.
Recommended to leave as Off (default) unless high security monitoring of Wi-Fi link is needed.

Wi-Fi Client

Configuration

This setting enables a Wi-Fi connection from the panel to a router for WAN access. Enabling this
selection will cause the SSID and credential information for a network to join to be accessible.

4. Disconnect the battery from the battery connector (E in Figure 2) by pressing down on the wire end of the battery clip.

5. Remove the Communication Modules Cover by pulling outward on the tabs (F in Figure 2) and then lifting upward when tabs
release.

6. To access the location of the Bluetooth Wi-Fi module, remove the System Electronics Cover (this is the cover with a printed
wiring diagram) by pulling outward on the tabs (C in Figure 2), then disengaging the latch (D in Figure 2) with a small
screwdriver and lifting the cover upward when the latch releases.

Installing the Bluetooth Wi-Fi Module

1. Install the Bluetooth Wi-Fi module (A in Figures 1 and 3) into the Bluetooth Wi-Fi module location (with the bar code label side
up). Carefully align the header of the module (B in Figures 1 and 3) with the pins on the main circuit board. Press into place.

Note: The Bluetooth Wi-Fi module must be installed on the main board in the Bluetooth Wi-Fi location (A in Figure 3). DO NOT
force the module into place.

2. Reinstall the System Electronics Cover, making sure the tabs (C in Figure 2) and the latch (D in Figure 2) are engaged.

3 Reinstall the Communication Modules Cover by pressing the cover down until the tabs (F in Figure 2) snap into place.
Note: All three internal covers must be secured for proper operation.

4. Supply power to the panel as noted in Table 2.

Table 1: Powering the Panel

Note: Connect the battery within 15 seconds of providing AC power to reduce the potential for a low battery indication.

5. Connect the battery to the battery connector on the panel (E in Figure 2).
Note: The cable connector locks into place.

6 Close the panel, making sure all tabs are engaged. Replace the screw securing the panel chassis.

7. If the central monitoring station was notified, inform them this operation is complete.

Module Configuration and Programming

Module Configuration – Wi-Fi Capability

1. Press the Settings icon on the lower left of the AdvisorOne main screen.

2. Press CONFIGURATION to enter programming. Enter installer or dealer code.

3. From the Configuration & Programming screen, press COMMUNICATION.

4. From the Communication screen, press INTERFACES.
For Wireless WAN
5a. From the Interface Communication screen, for press EDIT next to Wireless WAN. The following is displayed:

Table 2: Wi-Fi Wireless WAN Options

2 / 6 AdvisorOne Bluetooth WiFi Module Installation Sheet