UTC Fire and Security Americas 787E SIMON User Manual

Download

Page 1

6LPRQ6HFXULW\ 6\VWHP&RQWURO 3DQHO

Document Number: 466-1873 Rev. C PRELIMINARY May 2002

ITI Part Nos. 60-875

60-910

Doors &

Motion

Windows

Sensors

Status

Arm

5 / 6

3 / 4 7 / 8

1 / 2

Special

Doors

Chime

FIRE

POLICE

Test Weekly

H O M E S E C U R I T Y

System

Disarm

9 / 0

C O D E

Off

SensorMotion Time

H O M E C O N T R O L

Lights

E M E R G E N C Y

AUX

Contents

About This Manual 1

Special Installation Requirements 1

UL Listed Installations 1 Central Station Reporting 1 UL Canada Listed Installations 1 California State Fire Marshall Listed Installations 2

Planning the Installation 2

Standard Panel 2 Interrogator 200 Audio Verification Module 2

Installing the System 2

System Components 2

Control Panel 2 System Devices 3

Planning Sensor Types & Locations 3

Device Locations 4

Control Panel 4 Remote Handheld Touchpad 4 Keychain Touchpad 4

X-10 Modules 4

House Code and Unit Numbers 4

Installing the System 5

Materials Needed 5 Opening the Panel Cover and Chassis 5 Mounting the Panel 5 Connecting Hardwire Devices 6

AC Terminals 6 HWIN1, HWIN2, and DCOUT Terminals 6

Wiring Interior Sirens 6

LD105 Hardwire Interior Siren 6

Wiring Exterior Sirens 7

Hardwire Exterior Siren with Supervision 7

Hardwire Exterior Siren without Supervision 7 Wiring Hardwire Contacts 7 Wiring a Phone Line to the Panel 7

Full Line Seizure 7

No Line Seizure 8 Wiring the Power Transformer 9 Powering Up the Panel 9

Installing the Panel Backup Battery 9

Applying AC Power 9 Installing X-10 Modules 9

Lamp and Appliance Mod ul es 9

Installation Instructions

Universal Module 10

Sensor Installation 10

Programming 10

Entering Program Mode 10 Closing the Cover 10 Reset Memory to the Factory Defaults 10 Set the Clock 10 Adding (Learning) Sensors 10

Deleting Sensors 12 X-10 Module Operation 12 Numbered Options 12

Option 01: Panel Piezo Beeps 13

Option 02: Panel Voice 13

Option 03: Latchkey 13

Option 04: Primary Phone Number 13

Option 05: Secondary Phone Number 13

Option 06: Downloader Phone Number 14

Option 07: Account Number 14

Option 08: Phone Lock 14

Option 09: Downloader Code 14

Option 10: Entry Delay 14

Option 11: Exit Delay 14

Option 12: Phone Mod 1 15

Option 13: Phone Mod 2 15

Option 14: DTMF Dialing 15

Option 15: No Activity Time-out 15

Option 16: Auto Phone Test 16

Option 17: Dialer Delay 16

Option 18: Alarm Cancel Report 16

Option 19: RF Timeout 16

Option 20: Manual Phone Test 16

Option 21: Opening Report s 17

Option 22: Closing Reports 17

Option 23: Force Armed Report 17

Option 24: AC Power Failure Report 17

Option 25: CPU Low Battery Report 17

Option 26: Fail to Communicate 17

Option 27: Ring/Hang/Ring 17

Option 28: No Delay from Keychain Touchpad 18

Option 29: Panel Piezo Alarms 18

Option 30: Panel Panic Ala rms 18

Option 31: Downloader Enable 18

Option 32: 300 Baud 18

Option 33: Audio Verification 18

Option 34: Fail to Open Report 18

Option 35: Fail to Close Report 19

Page 2

Option 36: Sensor Activated Light Lockout Start

Time 19

Option 37: Sensor Activated Light Lockout Stop

Time 19 Option 38: Auto Arm 19 Option 39: Siren Time out 19 Option 40: Troub le Beeps 20 Option 41: Chime Voice 20 Option 42: Speaker Level 20 Option 43: Numeric Pager/Voice Event Notification

Phone Number 20

Option 44: Numeric Pager/Voice Event Notification

Phone Mod 3 20 Option 45: Sensor Alarm Restoral Report 21 Option 46: Fire Shutdown - AVM 21 Option 47: AVM Mode 21 Option 48: Panic Talk - AVM 21 Option 49: Arming LEDs Shutdown 21 Option 50: RF Jam Detect 21 Option 51: 24 Hour Tamper 21 Option 52: Unvacated Premises 22 Option 53: Hardwire Siren Supervision 22 Option 54: Access Code Length 22 Option 55: Status Beep Volume 22 Option 56: Call Waiting 22 Option 57: Supervisory/Tamper Report 23 Option 58: Remote Touchpad Arming 23 Option 59: Exit Extension 23 Option 60: Secure Arming 23 Option 61: Demo Mode 23 Option 62: Supervisory Protest 23 Option 63: 24 Hour Time 23 Option 64: No Arm on Panel Low Battery 24 Option 65: No Usage Report 24 Option 66: External Siren Delay 24 Option 67: Quick Exit 24 Option 68: Swinger Shutdown 24 Option 69: SIA Limits 24 Option 70: Not Available Option 71: Programming Report 25 Option 72: Supervisory Time 25 Option 73: Modem Sensitivity 25 Option 74: Silent Panel Police Panic 25 Option 75: VOX Mic Gain 25 Option 76: VOX Gain Range 25 Option 77: Manual Mic Gain 25 Option 78: VOX Receiver Gain 26 Option 79: Panel Cover Tamper 26 Option 80: Alarm Report Verification 26

Programming System Access Codes 26

X-10 Operation 30

Manual Lamp Module Control 30 X-10 Siren and Lamp Module Functions 30

Emergency Planning 31 Appendix A: Troubleshooting 32

System Status 32 Control Panel 32 Options (Programmable by the homeowner) 32 Sensors 32 X-10 Modules 32

Appendix B: System Configuration 33

Alphabetical Listing of Sensor Names 33 Sensor Assignments/Locations 33 Sensor Group Characteristics 34 Home Control Planning 35 System Access Codes 35 Option Settings 36

Specifications 39

Testing the System 26

Control Panel 26 Sensors 27 Improving Sensor/Panel Communication 28

Antenna 28 If a Sensor Fails the Sensor Test 28

Phone Communication 28 Off-Site Phone Operation 29 Central Station Communication 29 Pager Communication 29 2-Way Voice Operation 29 Voice Event Notification 30

Page 3

FCC Notices

FCC Part 15 Information to the User

Changes or modifications not expressly approved by Interlogix Inc. ca n void the user’s authority to operate the equipment.

FCC Part 15 Class B

This equipment has been te sted and found to comply with th e limits for a Class B digital device, pu rsuant to part 15 of the FCC R ules. These limits are designed to provide reason able protection against interfe rence in a residential installation.

This equipment gen erates, uses, and ca n radia te radio fre qu ency e nergy an d, if not inst alle d and used in acc ordanc e wi th the instructi ons, may ca use har mful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cau se harmful interfere nce to rad io or televi sion rece ption, whic h can be det ermined by t urning th e equipm ent off and on, the user i s encouraged to try to correct th e interference by one or more o f th e following me asures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the af f e cted equipment and th e panel receiver to separate outlets , on different branch circuits. Consult the dealer or an experienced radio/TV technician for help. FCC ID: B4Z-787E-SIMON

ACTA Part 68

This equipment c omplies with P art 68 o f the FC C Ru les. Loca ted on this eq uipmen t is a label that c ontains, am ong o ther inform ation, the FCC registration number and the ringer equiv al en ce num be r (REN) for this equipment. If requested, thi s information must be provided to the telephone company.

FCC Part 68 Registration No. The REN is used to determine the maximum number of devices that may be connected to your telephone line. Excessive RENs on a telephone line may resu lt

in devices not ringing in response to an incoming call. In most areas, the sum of all device RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company. For products approved after July 23, 2001, the REN for this product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label.

A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements as adopted by ACTA. A compliant telephon e c ord and modular plug is provided wi th this product. It is designed to be conne cted to a compliant modular jack that is also compliant. See the Instal lation Instructions for details.

Alarm dialing equipment must be able to seize the telephone line and place a call in an emergency situation. It must be able to do this even if other equipment (telephone, answering system, computer modem, etc.) already has the telephone line in use. To do so, alarm dialing equipment must be connected to a properly installed RJ31X jack that is electrically in series and ahead of all other equipment attached to the same telephone line. Proper installation is depicted in the following diagram . I f you have any questions concerning these instructions, consult your local telephone company or a qualified installer a b out installing an RJ31X jack and al arm dialing equipment for yo u.

C u s t o m e r P r e m i s e s E q u i p m e n t a n d W i r i n g

N e t w o r k S e r v i c e P r o v i d e r ' s F a c i l i t i e s

T e le p h o n e L i n e

N e t w o r k D e m a r c a t i o n P o i n t

T e le p h o n e

R J 3 1 X

J a c k

U n u s e d

R J - 1 1 J a c k

A n s w e r i n g S y s t e m

A la r m D i a l i n g E q u ip m e n t

F a x M a c h in e

T e le p h o n e

C o m p u t e r

U n u s e d R J - 1 1 J a c k

T e le p h o n e

If this equipment causes harm to the t elephon e netwo rk, the telepho ne compa ny may tem porarily di sconne ct you r servic e. If possi ble, you wil l be notif ied in advance. When adv ance notice i s not practi cal, you wil l be notified as soon as possible. You will also be advised of your righ t to file a complaint with the FCC.

The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the operation of the equipment. You will be given advance notice in order to maintain uninterrupted service.

If you experience troubl e with t his equ ipment, ple ase contac t the com pany tha t installe d the eq uipment fo r service and/or re pair info rmatio n. The t elepho ne company may ask you to disconnect this equipment from the network until the problem has been correcte d or you are sure that the equipment is not m al functioning.

This equipment may no t be us ed on coin service provided by the telephone company. Connection to party lines is subjec t to sta te tariffs.

Page 4

Canada Notice

The Canadian Department of Communications label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protec ti ve , op erational, and safety requireme nt s. T he department does not guarantee the equipment will operate to the user’s satisfaction.

Before installing this equ ip ment, users sho uld ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be instal l ed usi ng an acceptable method of conn ec ti on. In some cases, the company’s inside wiring associated with a single- line individual service may be extended by means of a certified connector assembly (telephone extension cord). The customer should be aware that compliance with the above conditions may n ot prevent degradation of service in some situ at ion s .

Repairs to certified equipment should be made by an authorized Ca nadian maintenance facili ty designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malf u nctions, may give the telecommunica tions company cause to request the user to disconnect the equipment.

For your protection, make sure that the electrical ground connections of the power utility, telephone lines, and internal metallic water pipe system, if pres ent, are connected together.

&$87,21

Do not attempt to make connections yourself. Contact the appropriate electrician or electric inspections authority.

The Load Number (LN) assigned to each terminal device denotes the percentage of the total load to be connected to a telephone loop which is used by the device, to prevent overl oading. The termination on a loop ma y consist of any combinatio n of de vic es subject only to the requirem ent that the tota l o f the LNs of all the devices does no t exceed 100. Load Number: .1 Certification Number: 867 11636A

“AVIS: - L ´étiquette du ministèr e de s Com m uni c at io ns du Ca nada identifie le matériel homologué. Cette étiquette certifie que le matériel est conforme a certaines normes de protection, d ´ exploitation et de sécurité des réseaux de télécommunications. Le ministère n ´ assure toutefois pas que le matériel fonc- tionnera a la satisfacti on de l ´ utilisateur.

Avant d ´ installer ce matériel, l ´ utilisateur doit s ´ assurer qu´ il est permis de le raccorder aux installations de l ´ enterprise locale de télécommunication. Le matériel doit également etre installé en suivant une méthod acceptée de raccordement. Da ns ce rta i ns ca s, les fils int éri e urs de l´ enterprise utilisés pour un service individuel a ligne uni que peuvent etre prolongés au moyen d´ un dispositif homologué de raccordement (cordon prolongateur téléphonique interne). L ´ abonné ne doit pas oublier qu ´ il est possible que la conformité aux conditions énoncées ci-dessus n ´ empechent pas le dégradation du servic e dans certaines situations. Actuellement, les enterprises de télécommunication ne permettent pas que l ´ on raccorde l eur ma tériel a des jacks d ´ abonné, sauf dans les cas précis prévus pas les tar r if s p articuliers d e ces enterprises.

Les réparations de matériel homologué doivent etre effectuées pas un centre d ´ entretien canadien autorisé désigné par le fournisseur. La compagne de télé- communications peut dem a nder a l ´ utilisateur d e d ébrancher un appareil a la suite de réparations ou de modifications effectuées par l ´ utilisa teur ou a cause de mauvais fonctionnem ent.

Pour sa propre protection, l ´ utilisateur doit s ´ assurer que tous les fils de mise a la terre de la source d ´ énergie électrique, des lignes téléphoniques et des canalisations d ´´ eau métalliques, s ´ il y en a, sont raccordés ensemble. Cette précaution est particulièrement importante dans les régions rurales.

Avertissment. - L ´ utilisateur ne doit pas tenter de faire ces raccordements lui-meme; il doit avoir recours a un service d ´ inspection des installations élec- triques, ou a electricien, selon le cas”.

Une note expl icative sur les indices de charge (voir 1.6) et leur emploi, a l ´ intention des utilisateurs du matériel terminal, do it etre incluse dans l ´ information qui accompagne le mate ri el homologué. La note pourra it etre rédigée selon le modèle suivant:

“L ´ indice de char g e ( IC) ass ig né a chaque dispositif terminal indique, pour éviter toute surcharge, le pourcentage de la charge totale qui peut etre raccordée a un circuit téléphonique bouclé utilisé par ce dispositif. La terminaison du circuit bouclé peut etre constituée de n ´ import somme des indices de charge de l ´ ensemble des dispositifs ne dépasse pas 100.”

L ´ Indice de charge de cet produit est ____ ________.

Page 5

About This Manual

This manual provides information for planning, installing, programming, and testing this security system. When necessary, this manual refers you to other documentation included with compatible devices.

Planning sheets are included for you to record sensor locations and software programming settings.

Special Installation Requirements

This security system can be used as a fire warning system, an intrusion alarm system, an emergency notification system, or any combination of the three.

Some installations may require configurations dictated by city/ state codes, insurance, or Underwriter’s Laboratories (UL). This section describes the various component and configuration listings.

UL Listed Installations

This section describes the requirements for UL Listed installations.

Basic System

❑ Control Panel (60-875-95R or 60 -875-01-95R) ❑ Backup Battery 6V 1.2 AH (34-025) ❑ Standard Class II 9 VAC, 700 mA Power Transformer

(22-109-ITI) or Class II 9 VAC, 700 mA Line Carrier Power Transformer (22-129-ITI)

❑ Hardwire Interior Siren (13-374) or Hardwire Exterior

Siren (13-046)

Household Burglary Alarm System Unit (UL 1023)

Basic system, plus:

❑ Hardwire Magnetic Contact (13-068 or 13-071) or

Wireless Learn Mode Door/Window Sensor (60-362)

❑ Option 01: Panel Piezo Beeps set to on ❑ Option 10: Entry Delay set to 45 seconds or less ❑ Option 11: Exit Delay set to 60 seconds or less ❑ Option 19: RF Timeout set to 24 hours ❑ Option 29: Control Panel Alarms turned on ❑ Option 38: Auto Arm set to off ❑ Option 39: Siren Timeout set to 4 minutes or more ❑ Option 40: Trouble Beeps set to on ❑ Option 50: RF Jam Detect set to on ❑ Option 53: Hardwire Siren Supervision set to on if

Option 29: Control Panel Alarms is set to off

❑ Option 59: Exit Extension set to off ❑ Option 67: Quick Exit set to off

Household Fire Warning System (UL 985)

Basic system, plus:

❑ Wireless Smoke Sensor 60-506-319.5 or 60 -838-95

learned into sensor group 26

❑ Option 01: Panel Piezo Beeps turned on ❑ Option 19: RF Timeout set to 4 hours ❑ Option 24: AC Power Failure Report set to on

❑ Option 26: Fail to Communicate set to on ❑ Option 29: Control Panel Alarms set to on ❑ Option 39: Siren Timeout set to 4 minutes or more ❑ Option 40: Trouble Beeps set to on ❑ Option 50: RF Jam Detect set to on ❑ Option 53: Hardwire Siren Supervision set to on if

Option 29: Control Panel Alarms is set to off

UL 1023 & 985 24-Hour Backup

❑

For 24-hour backup, the total current draw for all connected devices is limited to 25 mA (during normal standby conditions) using a 1.2 AH battery.

UL 1635 Digital Alarm Communicator System

Same as UL 1023 & 985, plus:

Note

These option settings are in addition to UL 1023 and 985 and are required only if the sy st em is set up for Central station reporting.

❑ Option 12: Phone Mod 1 set to 0 or 1 ❑ Option 16: Auto Phone Test set to 001 ❑ Option 19: RF Timeout set to 4 hours ❑ Option 24: AC Power Failure Report set to on ❑ Option 25: CPU Low Battery Report set to on ❑ Option 50: RF Jam Detect set to on

Central Station Reporting

The panel has been tested with the following central station receivers using SIA and Contact ID reporting formats:

❑ Radionics D6600 Central Station Receiver ❑ Sur-Gard Central Station Receiver with models

SG-DRL2A and SG-CPM2

UL Canada Listed Installations

This section describes the requirements for CUL (UL Canada) Listed installations.

Canadian Standards CSA Certified Accessories Residential Burglary Alarm System Unit

(ORD-C1023-1974)

Basic system as described for “UL Listed Installations” plus:

❑ Hardwire Magne tic Contact (13-068 or 13-071) or Wire-

less Learn Mode Door/ Window Sensor (60-362)

❑ Option 39: Siren Timeout set to 5 minutes or more

Residential Fire Warning System Control Unit (ULC-S545-M89)

Basic system as described for “UL Listed Installations” plus:

❑ Wireless Smoke Sensor 60-506-319.5 or 60 -838-95

learned into sensor group 26

❑ Option 01: Panel Piezo Beeps turned on ❑ Option 19: RF Timeout set to 4 hours ❑ Option 40: Trouble Beeps set to on ❑ Option 39: Siren Timeout set to 5 minutes or more ❑ For 24-hour backup, the total current draw for all con-

nected devices is limited to 33 mA (during normal standby conditions) using a 1.2 AH battery.

Page 6

Planning the Installation

California State Fire Marshall Listed Installations

Applied for.

Planning the Installation

This section describes system capabilities to help you get familiar with the system. “Appendix B” provides planning sheets with tables that let you record the hardware and programming configuration of the system. Fill in all necessary information ahead of time to help prepare for system installation.

Standard Panel

The following describe the basic panel (out-of-b ox) hardware capabilities.

❑ Power: Input for an AC step-down, plug-in style trans-

former.

❑ 2 Siren Outputs/Zone Inputs: Terminals for connecting

hardwire sirens or normally cl osed (NC) loop switch circuits.

❑ Phone Line Connection: Allows panel to communicate

with central monitoring station and/or pagers.

System Components

The security system has three types of components: the control panel, devices th at repo rt to the panel , and devi ces that respond to commands from the panel (see Figure 1).

D O O R / W I N D O W

K E Y C H A I N

T O U C H P A D

S Y ST E M S TA T U S

A R M

D o or s &

W i nd o w s

A R M

M o ti o n

S en s o rs

D IS A R M

263

8 9

O n

E M E R G EN C Y

R E M O T E H A N D H E L D

A U D I O V E R I F I C A T I O N M O D U L E

d&sr e s H o l hB to eK y

T O U C H P A D

S E N S O R

M o t io n

D o o rs & W i n d o w s

S e n s o rs

A rm

1 / 2

3 / 4

S p e c ia l M o t io n

O ff

D o o rs

C h im e

OF F

HO US E CO DE

UN IT CO DE

X -1 0 P O W E R H O U S E

CO NT IN UO US

SO UN D ER ON LY

SO UN D ER & RE LA Y

MO M EN TA RY

U N I V E R S A L

M O D U L E

F IR E

T e s t W e e k ly

RE LA Y O N LY

Figure 1. Typical Security System Components

S y s te m S ta t u s

D is a r m

5 / 6

7 / 8

S e n s o rT im e

L ig h ts

P O L I C E

L A M P

M O D U L E

M O T I O N S E N S O R

9 / 0

O f fO n

A U X

1 5

1 3

1 1

H O M E S E C U R I T Y

C O D E

H O M E C O N T R O L

E M E R G E N C Y

A P P L I A N C E

M O D U L E

1 5

1 3

1 1

S M O K E

S E N S O R

CA R B O N M ON O X ID E

D E T E C T O R

DO N OT P AIN T

C A R B O N M O N O X I D E

A L A R M

F R E E Z E

S E N S O R

Interrogator 200 Audio V er i fication Module

Adding this module allows central station operators to listen-in and talk to occupants on the premises to verify an emergency when an alarm report is received.

Installing the System

This section describes how to install the system control panel. Before starting the installation, plan your system layout and programming us ing t he work she e t s pr ov i ded i n “Appe nd i x B.”

Installing the system consists of the following:

❑ Determining Panel and Device Locations ❑ Mounting the Panel ❑ Connecting Sirens ❑ Connecting Normally Closed Loop Switch Circuits ❑ Connecting the Phone Line to the Panel ❑ Connecting the AC Power Transformer ❑ Powering Up the Panel

Control Panel

The control panel is the main processing unit for all system functions. It receives and responds to signals from wireless sensors and wi reless touchpads t hroughout the premises. For monitored systems, the panel can be connected to the premises phone line for central monitoring station and/or pager reporting.

Two panel models are available. One has an on-board 2-way voice microphone, the other does not. The Interrogator

200

Audio Verification Module can be added to either panel.

User Interface

When the panel cover is closed, the panel buttons operate the security system. The user operates the panel by pressing panel buttons or by using a touchpad. See the User Manual for complete operation instructions.

When the panel cover is open, the buttons program the security system. The panel can be programmed on-site by the installer or user, or from off-site using ITI ToolBox

software. See the “Programming” section of this manual for complete on-site programming instructions. See the ITI ToolBox manual and

T o ol Bo x on- l ine he lp for off-site programming instruc ti o ns.

Note

ITI ToolBox has not been investigate d by UL and should not be used to program panels in UL listed systems.

Panel Tamper

If the panel cover is opened while the system is armed, an intrusion alarm occurs. When the system status button is subsequently pressed, the panel says System Access Alarm.

Page 7

Planning Sensor Types & Locations

System Devices

The system can monitor up to 24 sensors and may use any of the following:

Door/Window Sensor (60-670)

For intrusion protection, install Door/Window sensors on all ground-floor doors and windows. At a minimum, install them in the following locations:

❑ All easily accessible exterior doors and windows. ❑ Interior doors leading into the garage. ❑ Doors to areas containing valuables such as cabinets and

closets.

Indoor Motion Sensor (60-639)

Indoor motion sensors are ideal whenever it is not practical to install door/window sensors on every opening. Identify areas where an intruder is likely to walk through. Large areas in an open floor plan, downstairs fa mily rooms, and hallways are typical locations for indoor motion sensors. For installations with pets, use the ITI SAW Pet Immune PIR (60-807).

Outdoor Motion Sensor (60-639)

Use outdoor motion sensors to detect motion in a protected outdoor area. Detected motion in this protected area can sound chimes or turn on outside lights. Do not use Outdoor Motion

Sensors for intrusion protection.

Freeze Sensor* (60-742)

Freeze sensors detect low temperature conditions which may indicate a furnace failure. The sensor contains a bimetallic thermal switch connected to the built-in transmitter. The sensor transmits an alarm signal to the panel when the surrounding temperature dr ops to about 41°F. When the temperature rises to 50°F, the sensor transmits a restore signal.

Water Sensor* (60-744)

Water sensors detect a water leak/rising water. The detector is connected to the sensor by an 8-foot (2.4-meter) cable. Water that reaches both detector contact points activates the sensor, causing it to transmit an alarm signal.

Smoke Sensor (60-848-95)

Smoke sensors provide fire protection by causing an alarm to sound throughout the house. You can add smoke sensors near sleeping areas and on every floor of the house. Avoid areas that could have some smoke or exhaust such as attics, kitchens, above fireplaces, dusty locations, garages, and areas with temperature extremes. In these areas you may want to install Rateof-Rise sensors to detect extreme temperature changes. See “Emergency P lan ni n g” and the instructions packaged with the smoke sensor for complete placement information.

Keychain Touchpad* (60-659)

The Keychain Touchpad lets you turn the system on and off from right outside the home or activate a panic alarm if there is an emergency. If you have X-10 Lamp Modules, you can use keychain touchpads to turn all system controlled lights on and off.

Remote Handheld Touchpad (60-671)

The Remote Handheld Touchpad lets you turn the system on and off while in the home, turn system controlled lights on and off (all or individual lights), or activate a panic alarm if there is a non-medical emergency.

X-10 Modules*

When the panel is powered using the line carrier power transformer, the system can work with any of the following modules:

❑ X-10 Appliance Module (13-402) ❑ X-10 Powerhorn/Remote Siren Module (13-398) ❑ X-10 Universal Mo du l e (1 3- 39 9)

Note

Use of X-10 modules has not been investigated by UL.

Interrogator® 200 Audio Verification Module* (60-787)

The Audio Verification Module (AVM) gives the central station operator the ability to hear what’s happening at the premises during an alarm and to speak directly to the system user. The operator can then determine how serious an alarm is, find out what kind of help is needed, and dispatch the appropriate assistance. Only one AVM may be installed per panel.

Planning Sensor T ypes & Locations

The first step to an easy and successful installation is to decide what areas or items to protec t, which lights or appliances to operate, and the best location for the panel, touchpad, sensors, and sirens.

Metal objects, mirrors, and metallic wallpaper can block signals sent by the wireless sensors. Make sure there are no metal objects in the way when installing the system.

Use the planning tables in “Appendix B” to determine the appropriate Sensor Type for the sensors you will be adding. You’ll need to understand the application for each sensor. For example, Keychain Touchpads are typically programmed as sensor type 01 (Porta ble pa nic), us ed to send an intrusio n alarm to a central monitoring station. This sensor type is instant intrusion, it does not re qui re res tor al or su pervi sory comm unic ation with the panel and it is active in 4 arming levels (disarm, arm doors & windows, arm motion sensors, and a r m doors/windows and motions sensors).

Carbon Monoxide (CO) Alarm* (60-652-95)

The Learn Mode™ CO Alarm alerts users to hazardous levels of carbon monoxide gas. If dangerous concentrations of gas are present, the red indicator light comes on, the internal siren goes off, and an alarm is transmitted to the panel. The panel sounds its own alarm and reports to the central station.

* Not investigated for use by UL.

Page 8

Planning Sensor Types & Locations

Recommended Sensor Types

Device Recommended

Sensor Type

Keychain Touchpad 01, 03, 06, 07 Remote Handheld Touchpad 01, 03, 06, 07 Indoor Motion Sensor 17 (intrusion), 25

(chime) Outdoor Motion Sensor 25 Smoke Sensor 26 Exterior Door 10 Interior Door 14 Window Sensor 13 CO Alarm 34 Freeze & Water Sensors 29

Device Locations

Note

All Lamp Modules with the same house code will turn on or flash as a group during an alarm or when operating the “Light” button on a Keychain Touchpad.

The numbered dial sets the unit number, which identifies and lets you control a specific device. Each device must have a unique unit number (1-8) to be individually controlled. For example, lights and appliances operated from a Remote Handheld Touchpad or operated by a sensor; or lights programmed to go on during the entry/exit delay or at scheduled times.

Note

When unit numbers 9-16 are used for lamp modules, they can only be controll ed b y an al l on or al l off command.

A lamp will flash to the arming level if its unit number is set to 10. A lamp set to unit number 10 will flash once if the panel is disarmed, twice if doo rs & w indows are armed, etc.

The remote siren can be set to any un i t nu m ber to hear alarm sounds. Set it to unit number 9 to also hear arming level beeps, status beeps, and trouble beeps.

Do not use a lamp module to control appliances. Use an appliance module, si nce the w at tage rati ng on Lamp Modules is less than on Appliance Modules.

Control Panel

Locate the panel where alarm sounds can be heard and is easily accessible for operation.

Do not install the panel near a window or door where it can be reached easily by an intruder.

Remote Handheld Touchpad

Locate Remote Handheld Touchpads where they will be convenient and offer quick access to the user.

Keychain Touchpad

Keychain Touchpads attach to the owner’s key ring or can be conveniently carried.

X-10 Modules

The system can control up to 8 individual unit numbers on Lamp, Wallswitch, Appliance, and Universal Modules.

House Code and Unit Numbers

To Fill Out the Home Control Planning Table:

1. Set the house code on all modules (except the remote siren) to the same letter.

Note

The house code instruct ions that come with the Powerhorn Siren won’t work with this panel. Follow the housecode instructions giv en here.

2. Set the Remote Siren house code to the next alphabetical letter. For example, if you chose house code B in step 1 above, set the remote siren house code to C.

3. Set the module unit numbers.

Note

If you are using a Universal M odule to operate a device, make sure to assign a unique unit number to this module, choosing from 1-8.

4. List the location of the lamp or appliance in the Location column of the Home Control Planning Table.

5. Write the location of each Lamp Module on an adhesive note and label the module.

6. Decide if the device should be activated by sensors, entry/exit delay , time, or a combination. An example of sensor activation is using a motion sensor to turn on a light. Record the information in the appropriate columns.

Each device (lamp, appliance, etc.) controlled by the panel must have an identification setting. The modules use two dials to set identification codes: one with letters A through P and one with numbers 1 through 16.

The lettered dial sets the house code, which enables the system to differentiate this home from other homes in the area. Set all modules (except the remote siren) and the panel to the same house code.

Page 9

Installing the System

Use the following tables to help you further plan X-10 module installation.

House Code Assignments

House Codes Results

A through P Set all modules to the same house

code except the remote sirens.

Next Higher House Code

Remote Siren must be set to the next higher alphabetical letter.

Unit # Result

1 - 8 Used for sensor-activated, time-activated,

and entry/exit delay lights.

❑ Sensor-activated lights are enabled and

disabled by pressing the LIGHTS Sensor Activated button on the panel.

❑ Time-activated lights are enabled and

disabled by pressing the LIGHTS Time Activated button on the panel.

If using the universal module to operate a device, be sure to assign a unique unit number.

❑ The STAR button on the KeyChain

Touchpad activates the universal module controlled device or to turn on special lights if programmed.

Installing the Syste m

This section describes how to open the panel for mounting, mount the panel, connect sirens, hardwire contacts, and the AC power transformer.

Materials Needed

❑ Pencil ❑ Phillips Screwdriver

Opening the Panel Cover and Chassis

Tabs at the top of the panel secure and release the front cover and the chassis. The plastic hinges on the panel bottom allow the cover and chassis to swing down and out of the way (see Figure 2).

Press tab with thumb, then swing cover down.

D o o r s &

M o ti o n

S t a t u s

W in d o w s

S e n s o r s

A r m

1 / 2

3 / 4 7 / 8

S p e c ia l M o ti o n T im e

D o o r s

C h im e

F I R E P O L I C E

T e s t W e e k l y

H O M E S E C U R I T Y

S y s t e m

D i s a r m

9 / 0

5 / 6

S e n s o r

L ig h t s

A U X

O n O ff

C O D E

H O M E C O N T R O L

E M E R G E N C Y

Press tab up with screwdriver, then swing chassis down.

9 Used for remote siren or light control.

❑ For remote siren use, House Code must

be set to next higher number to hear arming level beeps, status beeps, and trouble beeps.

❑ For light contro l, lamp modules with

this setting are controlled by an all on or all off command.

10 Used for remote siren or light control.

❑ For remote siren use, House Code must

be set to next higher number an d only alarm sounds occur at this setting.

❑ For light contro l, lamps will flash

according to selected arming level and are controlled by an all on or all off command.

11 - 16 Used for lamp modu les and cont rolled by an

all on or all off command.

Figure 2. Opening the Panel Cover and Chassis

Mounting the Panel

The panel can be mounted on a wall or on the optional Tabletop Base.

1. Choose a panel location.

2. Run all necessary power, phone, siren, and hardwire contact wires to the desired panel location.

Note

When choosing the AC outlet lo cation for the AC power transformer, make sure the outlet is not controlled by a switch or that it is not part of a ground fault interrupt circuit (GFIC).

3. Refer to Figure 3 for mounting hole locations. For wall mounting, hold the panel against the wall and

mark the mounting hole locations with a pencil. For Tabletop Base mounting, place the panel back on the base until the top and bottom mounting holes line up with the mounting posts on the base.

Page 10

Installing the System

Mounting Holes

Note

The total current available from the DCOUT terminal is 250 mA at up to 122° F (50° C).

With Option 53: Hardwire Siren Supervision turned on, sirens connected to HWIN1 and HWIN2 are supervised and require a

4.7k resistor in the circuit. If either of these terminals is not used with Option 53 on, you must connect a 47k resistor between the unused terminal and DCOUT.

Hardwire Detectors

T o set up HWIN 1 and/ or H WIN2 f or ha rdw ire det ect ors, make the required co nn e c ti ons as de sc r i bed under “Wiring Hardwire Detectors,” then proceed to the “Programming” section to add (learn) them into panel memory.

Wiring Interior Sirens

Panel terminal HWIN1 can be used for connecting interior sirens and activates for status and alarm sounds.

Interior sirens must always be wired with a resistor in the circuit. For circuit supervision which allows the panel to detect if the siren wire is cut (open), Option 53: Hardwire Siren Supervision must be turned on (see the “Programming” section).

LD105 Hardwire Interior Siren

Figure 3. Panel Mounting Hole L oc a t i ons

4. For wall mounting, insert anchors into holes where studs are not present.

5. Install all screws and tighten gently.

Connecting Hardwire Devices

The panel has 5 screw terminals located on the upper-right corner of the circuit board (see Figure 3) for connecting AC power, sirens and/or h ardwire detectors.

AC Terminals

Note

All input s and outputs are Class II power limi t ed circuits.

These terminals are used for connecting a 9 VAC, 700 mA AC power transformer. For systems with no X-10 modules, use transformer part no. 22-109-ITI. For systems wit h X -10 modules, use transformer part no. 22-TBD-ITI

HWIN1, HWIN2, and DCOUT Terminals

These terminals are dual purpose and can be used for either siren or hardwire detector connections.

Note

These terminals cannot provide both functions simultaneously.

Sirens

From the factory, these terminals are set up for siren operation with HWIN1 handling interior sirens (status and alarm sounds), HWIN2 h a ndling exterior sirens (alarm sounds only), and DCOUT providing the positive (+) voltage.

Connect the LD1 05 Hardwire Interior Siren (13-374) to the panel using a 4.7k resistor (included with siren) as shown in Figure 4. The resistor must be co nn ected acr oss the siren wires as close to the siren as possible.

Note

Do not install the resistor at the panel ter m in al s. Thi s does not provide supervision of the wire.

A C A C

4.7k Resistor (Locate at si r en)

Figure 4. Hardwire Interior Sire n wi t h Supervision

Note

If you are installing only an inter ior siren and no exterior siren and Option 53 is on, you must connect a 47k resistor between the HWIN2 and DCOUT terminals.

H W I N 2

RED

H W I N 1D C O U T

BLACK

Page 11

Installing the System

Wiring Exterior Sirens

Panel terminal HWIN2 can be used for connecting exterior sirens and activates when intrusion and fire alarms occur.

Exterior sirens can be wired with or without a resistor in the circuit for supervision. For circuit supervision which allows the panel to detect if the siren wire is cut (open), Option 53: Hardwire Siren Supervision must be turned on (see the “Program- ming” section).

Hardwire Exterior Siren with Supervision

Connect the Hardwire Exterior Siren (13-046) to the panel using a 4.7k resist or (in cluded w ith sir en) as shown in Figu re 5. The resistor must be connected across the siren wires as close to the siren as possible.

Note

Do not install the resistor at the panel terminals. This does not provide supervi s io n of th e w i re .

A C A C

H W I N 2

BLACK

RED

H W I N 1D C O U T

Wiring Hardwire Contacts

You can connect hardwire reed switches (normally closed loop only) to HWIN1 and/or HWIN2, if either terminal is not being utilized for a hardwire siren.

Important!

Connect only normally closed (N/C) reed switches to HWIN1 and/or HWIN2. Other types of hardwire detectors should not be used.

The total resistance of the wire loop must not exceed 3 ohms. This allows you to use up to 200 feet of 2-conductor, 22-gauge stranded wire.

Connect hardwire reed switches to the panel using a 47k resistor as shown in Figure 7. The resistor must be connected at the last switch in the circuit.

Note

Do not install the resistor at the panel terminals. This does not provide superv is io n of th e wi re .

A C A C

H W I N 2

H W I N 1D C O U T

4.7k Resistor (Locate at siren)

Figure 5. Hardwire Exterior Sire n with Supervision

Note

If you are installing only an exterior siren and no interior siren and Option 53 is on, you must connect a 47k resistor between the HWIN1 and DCOUT terminals.

Hardwire Exterior Siren without Supervision

With Option 53 turned off, connect the Hardwire Exterior Siren (13-046) to the panel without a re sistor as shown in Figure 6.

A C A C

H W I N 2

BLACK

RED

H W I N 1D C O U T

47k Resistor

Figure 7. Connecting Normally Closed Hardwire Reed

Switches

Wiring a Phone Line to the Panel

You can connect a phone line to the panel for systems monitored by a central monitoring station and/or systems that notify users by a digital pager or voice event notification.

Basically, there are two methods for connecting the panel to a phone line; full line seizure and no line seizure.

Full Line Seizure

This method requires that the panel be wired ahead (or in front) of all other phones, answering machines, computers, or any other devices on the phone line. This allows the panel to take over (seize) the phone line, even if another device on the line is in use.

An RJ-31X (CA- 38A) ja ck should be ins talled w hen wir ing for full line seizure. This lets the user quickly and easily disconnect the panel from the phone line in case the panel disables the phone line due to a malfunction.

Figure 6. Hardwire Exterior Siren without Supervision

Page 12

Installing the System

Full Line Seizure Wiring with an RJ-31X

Note

For UL Listed systems, th e R J- 31X jack must be mounted within 5 feet of the panel .

1. Run a 4-conductor cable from the TELCO block to the RJ-31X (A in Figure 8).

2. Connect the 4-conductor cable wires to the RJ-31X (B in Figure 8).

3. Disconnect the Green and Red premises phone jack wires from the TELCO block and splice them to the 4conductor cable Black and White (or Yellow) wires (C in Figure 8). Use weatherproof wire connectors for these splices.

4. Connect the 4-conductor cable Green and Red wires to the TELCO block TIP (+) and Red to RING (-) posts (D in Figure 8).

5. Connect the phone cord included with the panel to the RJ-31X and the panel LINE IN jack (E in Figure 8).

Full Line Seizure Wiring with 1 Premises Phone

If a single phone is all that exists on the premises, full line seizure can be accomplished without an RJ-31X.

Note

If the customer ever adds a phone or other phone device to another phone jack, fu ll lin e sei z ure no longer exists. Inform the customer to contact you if they want to add a phone or other device so that you can rewire for full line seizure by adding an RJ-3 1X.

1. Disconnect the phone from the premises phone jack and plug it into the panel PHONE jack (A in Figure 9). This jack is disconnected automatically whenever the panel reports.

2. Connect the phone cord included with the panel to the panel LINE IN jack and the premises phone jack (B in Figure 9).

Lone Premises Phone

BRN

GRN

Black

Green

Black

Green

TIP (+)

GRY

RED

Red

RING

(-)

Red

White (or Yellow)

Red

H W I N 1

H W I N 2

Premises Phone Jack

H W I N 2

Figure 9. Full Line Seizure Wiring with 1 Premises

Phone

White

(or Yellow)

No Line Seizure

This method is typically used where DSL (digital subscriber

line) service exists. DSL allows multiple devices on a single phone line to be used simultaneously. Simply connecting the panel LINE IN jack to an available phone jack on the premises is all that is required.

An in-line filter may be required to ensure panel reporting is successful.

Note

Connecting the panel to a standar d phone (voice) line in

Premises Phone Jack Wires

this manner should be avoided. Other devices in use at the same time t he panel i s using the line can prevent reports from going t hrough.

Figure 8. Full Line Seizure Wiring with an RJ-31X

Page 13

Installing the System

Wiring the Power Transformer

Connect the power transformer to the panel AC terminals as shown in Figure 10.

Note

Do not plug in the transformer at this time.

A C A C

Figure 10. Connecting the Power Transformer

H W I N 2

H W I N 1D C O U T

Powering Up the Panel

When applying power to the panel connect the battery first, then plug in the AC power transformer. This sequence prevents a battery fault condition.

Installing the Panel Backup Battery

3. Connect the red and black battery leads (included with panel) to the battery and panel terminals (see Figure

12).

Black

Red

1. Position and push the battery between the 2 flexible tabs (A in Figure 11).

2. Slide the battery to the left until the tabs snap into place, securing the battery (B in Figure 11).

Tabs

Figure 12.Connecting the Battery Leads to the Battery

and Panel Terminals

Applying AC Power

Note

Make sure the outlet is not controlled by a switch or that it is not part of a ground fault interrupt circuit (GFIC).

1. Remove the center screw from the outlet cover plate and hold the cover plate in place.

WARNING! Use extreme caution when securing the transformer to a met al outlet cover. You could receive a serious shock if a metal outlet cover drops down onto the prongs of the plug while you are sec uring the transformer and outlet cover to the outlet box.

2. Plug the transformer into the lower receptacle of the outlet so that the hole in the transformer tab lines up with the outlet cover screw hole. The panel voice should announce “Hello, system n is o.k.”

3. Insert the cover plate screw through the tran sformer tab and the outlet cover plate. Tighten the screw firmly.

Installing X-10 Modules

Figure 11.Installing the Panel Backup Battery

Lamp and Appliance Modules

1. Set the unit code dial to a unit number dif ferent from all other X-10 modules (between 1 and 8).

Page 14

Programming

2. Set the house code for the installation.

3. Plug the module into a wall outlet.

4. Plug the lamp/appliance into the module.

CAUTION!

Do not plug in appliances or lamps with 300 -watt or larger bulbs into Lamp Modules.

Universal Module

1. Set the unit code dial to a unit number different from all other X-10 modules (between 1 and 8).

2. Set the house code for the installation.

3. Set the module switches to momentary and relay only.

4. Connect the module terminals to the desired device terminals.

5. Plug the universal module into a wall outlet.

Note

See “Light and Appliance C on trol s” to program a Keychain T ouchpad to activate a Universal Module controlled device.

Sensor Installation

Program sensors and devices before you install them. Use the following section to program the panel and add the sensors to panel memory.

Programming

Entering Program Mode

There are 2 codes you can use to enter program mode.

Utility Access Code 1 (Dealer Code)

Depending upon how Option 54 is set, the default utility access code is 654321, 54321, 4321 (factory default), or 321. This code can be used for all programming.

Utility Access Code 2 (Installer Code)

Depending upon how Option 54 is set, the default access code is 654321, 54321, 4321 (factory default), or 321. This code is limited to changing all but the following: Utility Access Code 1, Options 4, 5, 6, 8, 9, 12, 13, 54, and 69.

1. Open the panel cover.

2. Enter Utility Access Code 1 or 2 using the numbered keys.

The panel is now in program mode. Follow the programming arrows on the panel label. The system prompts you through programming steps with beeps and voice messages.

Note

Do not remove panel power whi le in prog ra m mode. Programming changes are saved only when exiting program mode (closing the panel cover).

Program the panel in this order:

1. Set the panel clock.

2. Add (learn) sensors.

3. Set House Code and Light & Appliance Controls (Entry/Exit activated lights, Sensor activated lights, Time activated lights).

4. Change numbered Options as needed.

Exiting Program Mode

Close the cover to exit program mode when you are finished programming.

CAUTION!

Do not power down the panel while in program mode or all programming will be lost. The panel stores programmed information only when you exit program mode (close the cover and leave closed for at least 5 seconds).

Reset Memory to the Factory Defaults

1. Open the panel cover and enter Utility Access code 1.

2. Unplug the transformer and disconnect the battery.

3. Simultaneously pres s an d ho l d Cancel, Clock Set, and Minutes +.

4. Restore power to the panel with either the battery or the transformer while pressing these three buttons. The panel announces “Hello. System XX OK.” Release the buttons.

5. Connect the remaining power source to the panel.

Note

If Option 8: Phone Lock is on, options 04, 05, 06, 08, 09, 12, and 13 will not reset to thei r de fa ul ts.

Set the Clock

1. Press Clock Set from the Start Menu.

2. Press the Hours + and

– keys and listen to the voice

prompts. Stop when panel voice announces the correct hour.

3. Press the Minutes + and

– keys and listen to the voice

prompts. Stop when the panel announces the correct minutes.

4. Press Done. The panel announces the set time.

Adding (Learning) Sensors

These instructions de sc rib e how to ad d sensors, touchpads and other system devices into panel memory. The panel recognizes a sensor when you press a sensor program button, pr ess and release a tamper switch, press a sensor test button, or put a sensor into alarm.

Note

The hardwire inputs must ha ve si r ens or hardwire sensors with 47k Ohm resistors connected between the DCOUT and HWIN1 or HWIN2 terminals before learning in a sensor. If one of these connections is no t made, the panel will learn in a hardwire zone.

Note

If you are installing a sensor on a gun case, jewelry box, or similar usage, and the s ensor is active in level one, you must sub-disarm to avoid putting the panel into alarm when the sensor and the magnet are separated.

The following table, “Device Programming,” describes the programming button location for each device.

Page 15

Programming

Device Programming

Device To Program

Door/Window Sensor Press button on top of sensor

(cover removed) or trip tamper

Motion Sensor Press button on back of sensor

(mounting plat e removed) or trip tamper

Smoke Sensor Trip tamper, press test button, or

put sensor in alarm

Keychain Touchpad Press and hold Lock & Unlock

buttons together

Remote Handheld

Press the EMERGENCY buttons

Touchpad Hardwire Sensors Separate sensor from magne t CO Alarm Plug in the module and within 30

seconds press and hold the test button for 6 beeps

Freeze & Water Trip tamper or press and hold

button on top of the sensor (cover removed) until control panel confirms prog ra m ming. If button is not held down long enough, SYSTEM STATUS reports sensor as open.

Use the Table in Appendix B, which was filled out during the system planning, to help program sensors.

To add a hardwire or RF sensor or remote control:

1. Press

Add. The panel announces “Select from Main

Menu.”

2. Press Sensor/Remote. The panel announces “Press but-

ton on sensor.”

3. Press the sensor program button or release sensor tampe r switch. The panel announces “Keychain Remote. Press sensor again fo r next name or press Done to select.”

4. Press Sensor/Remote repeatedly until you hear the name or item you want to use. An alphabetical list of names the panel uses appears in Appendix B. Each name ma y be used more than once.

Note

For a more specific location name, press Option # for compass directions (north, northeast, east, southeast , south, southwest, west , nor t hw est).

5. Press DONE when you hear the desired name. The panel announces “Use numbered keys to ente r sensor group.”

6. Enter the 2-digit sensor group. The panel announces the sensor group and the first available sensor number, then prompts you to press DONE to accept.

Note

If you wish to use a sensor nu m ber ot her than the next one available, use the numbered keys to enter a 2 digit sensor number immediately after entering the sensor type.

7. Press DONE. The panel confirms programming by announcing the sensor number, name, a nd group.

When adding (learning) sensors, the panel uses an ascending numbering sequenc e star t ing with 1. You can override this by entering the desired sensor number using the numbered keys.

Version 3

Press for program

information.

Light

Control

Add

START MENU

Delete

Option #

Unit #

Entry/Exit

Delay

CONTROL MENU

Sensors

Instruction Summary

Add Option

Option #1:

Panel Beeps Panel Voice

Option #2:

Latchkey Time

Option #3: Option #36:

Sensor Activated Light Lockout Start Time Sensor Activated Light Lockout Stop Time

Option #37:

Chime Voice

Option #41:

Speaker Volume

Option #42:

Pager Phone Number

Option #43:

Status Beep Volume

Option #55:

Add Option #

Press

and follow voice prompts.

See Note

DONE

Add Access Code

Press

use red numbers to enter 4-digit code.

Set Clock

Press

Cancel

MAIN MENU

Sensor/ Remote

Time

645

Minutes

Add

Clock Set

Test

Access Clock

Code

DONE

Access Code

See Note

Minutes

Hours

See Note

Set

Hours

, then

DONE

System should be checked by a qualified technician at least every three years.

Note:

Hold key or press repeatedly until you hear the desired item.

978

Delete

To delete an option or access code

Delete

press prompting.

and follow the voice

Cancel

If you make a mistake or want to

start over press

Cancel

Sensor or Phone Test

To select a test, press follow the voice prompting.

422-2806 Rev A

Test

and

Page 16

Programming

Deleting Sen sors

To delete sensors:

1. Press

Delete. The panel announces “Select from Main

Menu.”

2. Press Sensor/Remote repeatedly until you hear the name and number you want deleted, then press DONE. The panel announces that the sensor is deleted.

X-10 Module Operation

Use the following procedure to program X-10 module operations into panel memory. Notice that the Light Control button is used to program all X-10 module operations (light, appliance, and universal).

To program the house code:

1. Press Add.

2. Press Light Control repeatedly until you hear the desired house code letter.

3. Press DONE.

4. Set the HOUSE dial on each lamp, appliance, and universal module, to the same letter.

5. Set the HOUSE dial on powerhorn/remote sirens to the next sequential alphabetical letter.

To add an entry/exit activated module:

1. Press

2. Press Light Control.

3. Press Unit # repeatedly until you hear the unit number

4. Press Entry/Exit Delay. The panel confirms your pro-

ADD.

that matches the one you chose for the module. gramming.

To add a time-activated module:

1. Press

Add.

2. Press Light Control.

3. Press Unit # until you hear the unit number that matches

the one you ch ose on the module.

4. Press Time .

5. Press Hours and Minutes to set the beginning of the

schedule.

6. Press DONE.

7. Press Hours and Minutes to set the end of the schedule.

8. Press DONE. The panel c onfirms your programming.

To delete an Entry/Exit-activated module:

1. Press

Delete.

2. Press Light Control.

3. Press Unit # repeatedly until you hear the unit number

you want deleted.

4. Press Entry/Exit Delay, then press DONE. The panel

confirms you r programming.

To delete a sensor-activated module:

1. Press Delete.

2. Press Light Control.

3. Press Unit # repeatedly until you hear the unit number

you want deleted.

4. Press Sensors until you hear the one you want deleted.

5. Press DONE. The panel c onfirms your programming.

To delete a time-activated module:

1. Press Delete.

2. Press Light Control.

3. Press Unit # repeatedly until you hear the unit number

you want deleted.

4. Press DONE. The pane l confirms your pro gramming

To add a sensor-activated module:

1. Press

ADD.

2. Press Light Control.

3. Press Unit # repeatedly until you hear the unit number that matches the one you chose for the module.

4. Press Sensors until you hear the sensor you want to control the light.

Note

A Keychain Touchpad button can also be programmed to control a light or appliance m odule.

5. Press DONE. The panel confirms your programmin g.

Numbered Options

Numbered options let you customize system operation according to dealer and user needs.

The “Numbered Options” table in Appendix B lists all system options and their characteristics. Fill in the last column of the table before programming to help speed up the programming process.

There are two ways to reach the desired option setting.

❑ Press Add or Delete, then press Option # repeatedly until

you hear the option you want changed.

Or—

❑ Press Add or Delete, Option #, then enter the option num-

ber using the numbered keys.

The following instructions use the last method.

Note

Although the panel voice prompts you through programming, it is not necessary to wait for the complete message before pressing the next button in the programming sequence.

Page 17

Programming

Option 01: Panel Piezo Beeps (Default = On)

Determines whether the panel piezo produces beeps based on system activity (on) or is silent (off). The following table describes all possible beeps .

Panel Piezo Beeps

Activity Piezo Beep Response

ARM Doors & Windows

Exit Delay—2 beeps sound every 5 seconds and 2 times per second during the last 10 seconds.

Silent Exit—2 beeps sound at the beginning of the exit delay an d 2 more sound just before the exit delay expires.

Entry Delay—2 beeps sound every 5 seconds and 2 times per second during the last 10 seconds.

ARM Motion Sensors

Exit Delay—3 beeps sound every 5 seconds and 3 times per second during the last 10 seconds.

Silent Exit—3 beeps sound at the beginning of the exit delay an d 3 more sound just before the exit delay expires.

Entry Delay—3 beeps sound every 5 seconds and 3 times per second during the last 10 seconds.

Option 02: Panel Voice (Default = On)

Determines whether the panel announces all status, alarm, and program mode messages (on), or only announces messages for canceled alarms, open sensors (protesting), when SYSTEM STATUS is pressed, or if the panel is in program mode (off).

To turn on Panel Voice, press:

Add—Option #—02—DONE.

To turn off Panel Voice, press:

Delete—Option #—02—DONE.

Option 03: Latchkey (Default = Off)

Determines whether the panel reports a Latchkey alarm if the system is not disarmed at a preset time between midnight and 11:59

P.M. (on), or if the Latchkey feature is disabled (off).

Note

The system clock must be set for the Latchkey feature to work.

To set Latchkey, press:

Add—Option #—03—Hours—Minutes—DONE.

To turn off Latchkey, press:

Delete—Option #—03—DONE.

ARM Doors/ Windows & Motion Sens ors

Exit Delay—4 beeps sound every 5 seconds and 4 times per second during the last 10 seconds.

Silent Exit—4 beeps sound at the beginning of the exit delay an d 4 more sound just before the exit delay expires.

Entry Delay—4 beeps sound every 5 seconds and 4 times per second during

the last 10 seconds. DISARM 1 beep CHIME

2 beeps (when programmed) DOORS

CHIME

3 beeps (when programmed) SPECIAL MOTION

Trouble Beeps 6 beeps every minute. Press SYSTEM

STATUS to stop beeps f or 4 hours. No Activity 20 beeps every minute for 5 minutes

(when programmed)

To turn on Panel Piezo Beeps, press:

Add—Option #—01—DONE.

To turn off Panel Piezo Beeps, press:

Delete—Option #—01—DONE.

Note

For all UL listed systems, Op t ion 1 m ust be on (added).

Option 04: Primary Phone Number (Default = none)

Lets you program up to a 26-digit central monitoring station receiver phone number for monitored systems (on), or delete an existing primary phone number (off).

Press Test for each required pause, Add for a *, and Delete for a # (each of which uses one of the 26 available places).

To set Primary Phone Number, press:

Add—Option #—04—Up to 26 digits—DONE.

Note

Pressing DONE is required if you enter fewer than 26 digits. The phone number is aut om atically stored without pressing DONE if all 26 places are used.

To delete Primary Phone Number, press:

Delete—Option #—04—DONE.

Option 05: Secondary Phone Number

(Default = none)

Lets you program up to a 26-digit central monitoring station receiver/numeric pager/voice event notification phone number for monitored systems (on), or delete an existing secondary phone number (off).

Press Test for each required pause, Add for a *, and Delete for a # (each of which uses one of the 26 available places).

Page 18

Programming

Note

For numeric pagers, add 2 pauses at the end of the number. Some pagers may require 3 or 4 additional pauses to work correctly. Pagers that require the panel to dial more than 26 digits will not work.

The panel calls a numeric pager twice f or eac h re port. Silent alarms report to a pager as an intrusion alarm. See the T able “Pager Reporting Messages” for more reporting information.

To set Secondary Phone Number, press:

Add—Option #—05—Up to 26 digits—DONE.

Note

Pressing DONE is required if you enter fewer than 26 digits. The phone number is automatically stored without pressing DONE if all 26 places are used.

To delete Secondary Phone Number, press:

Delete—Option #—05—DONE.

Option 06: Downloader Phone Number

(Default = none)

Lets you program up to a 26-digit phone number for a computer modem for using ITI ToolBox Downloader (on), or delete an existing phone number (off).

Press Test for each required pause, Add for a *, and Delete for a # (each of which uses one of the 26 a vailable places ).

To set Downloader Phone Number, press:

Add—Option #—06—Up to 26 digits—DONE.

Note

Pressing DONE is required if you enter fewer than 26 digits. The phone number is automatically stored without pressing DONE if all 26 places are used.

Option 08: Phone Lock (Default = off)

Prevents resetting of phone/reporting related Options 04, 05, 06, 08, 09, 12, and 13 whe n a mem or y c le a r is pe r fo rme d ( on ), or resets these options to their default values when a memory clear is performed (off).

To turn on Phone Lock, press:

Add—Option #—08—DONE.

To turn off Phone Lock, press:

Delete—Option #—08—DONE.

Option 09: Downloader Code (Default = 12345)

Lets you set a unique 5-digit code that is required for initiating ToolBox sessions (on) or sets the code to its default (off).

The code must be 5 digits long and can range from 00000 to

99999. The Downloader Code must match the downloader access code in the ToolBox account to perform ToolBox sessions.

Note

The downloader code should always be changed from the default setting to avo id com petitor theft.

To set Downloader Code, press:

Add—Option #—09—5-digit code—DONE.

To delete Downloader Code (return to default), press:

Delete—Option #—09—DONE.

Option 10: Entry Delay (Default = 030 sec)

To delete Downloader Phone Number, press:

Delete—Option #—06—DONE.

Option 07: Account Number (Default = 00000)

Lets you program up to a 10-character alphanumeric account number (on) or delete an existing account number (off).

To enter letters (A - F only), p ress 9 th en the Minutes + button. The panel announces the letter A. Continue pressing the Minutes + button to progress through the alphabet.

Note

The CID format only supp orts account numbers with letters B through F, or numbers 0 through 9 (or a combination of those letters and numbers).

To set Account Number, press:

Add—Option #—07—Up to 10 characters—DONE.

Note

Pressing DONE is required if you enter fewer than 10 characters. The accoun t nu m ber is automatically stored without pressing DONE if 11 characters are entered, of which only the first 10 are stored.

To delete Account Number, press:

Delete—Option #—07—DONE.

Determines how much time the user has to disarm the system after entering the armed premises through a designated delay door, before an alarm occurs. Beeps sound during the entire delay time to remind the user to disarm the system.

When turned on, the Entry Delay can be set from 005-254 seconds (030-254 if SIA Limits Option 69 is on). All entries must be 3 digits. When turned off, the Entry Delay is set to 005 seconds (030 if Option 69: SIA Limits is on).

Note

For UL listed systems, the entry del ay must not exceed 45 seconds.

To set Entry Delay, press:

Add—Option #—10—3-digit delay time—DONE.

To reset Entry Delay (return to default), press:

Delete—Option #—10—DONE.

Option 11: Exit Delay (Default = 060 sec)

Determines how much time the user has to leave the premises through a designated delay door after arming the system. Beeps sound after arming the system to remind the user to leave the armed premises.

Page 19

Programming

If a delay door is opened after the Exit Delay expires, the Entry Delay begins. If the user arms the system with No Delay and opens a delay door after the Exit Delay expires, an alarm occurs.

When turned on, the Exit Delay can be set from 005-254 seconds (045-254 if SIA Limits Option 69 is on). All entries must be 3 digits. When turned off, the Exit Delay is set to 005 seconds (045 if Option 69: SIA Limits is on).

Note

For UL listed systems, the exit delay must not exceed 60 seconds.

To set Exit Delay, press:

Add—Option #—11—3-digit delay time—DONE.

To reset Exit Delay (return to default), press:

Delete—Option #—11—DONE.

Option 12: Phone Mod 1 (Default = 0)

Determines the primary phone number (Option 4) report content and reporting format.

Note

UL has only verified reporting compatibility with the ITI CS5000 Digital Alarm Communicator Receiver. For UL listed systems, Phone Mod 1 must be set to 0 or 1.

The following table describes the choices.

Option 13: Phone Mod 2 (Default = 00)

Determines the secondary phone number (Option 5) report content and reporting format. The following table describes the choices. All entries must be 2 digits.

Phone Mod 2

Setting # Content Format

00 All SIA 01 All Contact ID 02 Alarms o nly SIA 03 Alarms only Contact ID 04 Non-Alarms only SIA 05 Non-Alarms only Contact ID 06 Phone 1 failure SIA 07 Phone 1 failure Contact ID 08 Latchkey, No Activity, Phone Test,

Pager Openings, Closings, Fail to Open/ Close, AC Power Restorals/ Failures

09 Same as setting 8 plus Alarms Pager 10 Alarms only (See Options 43 and

44 for more det a i l s. )

Voice Event

Notification

Phone Mod 1

Setting # Content Format

0All SIA 1 All Contact ID 2 Alarms only SIA 3 Alarms only Contact ID

Alarms include: Fire , Intr usi o n, Emergency, Silent, and Alar m Cancels.

Non-alarms include: Latchkey, No Activity, Openings, Closings, Fail to Open, Fail to Close, Force Armed, AC Power Failure, CPU Low Battery, and Trouble Restorals.

To set Phone Mod 1, press:

Add—Option #—12—0, 1, 2, or 3—DONE.

To reset Phone Mod 1 (return to default), press:

Delete—Option #—12—DONE.

To set Phone Mod 2, press:

Add—Option #—13—0, 1, 2, or 3—DONE.

To reset Phone Mod 2 (return to default), press:

Delete—Option #—13—DONE.

Option 14: DTMF Dialing (Default = on)

Determines whether the panel uses DTMF (on) or pulse (off) for dialing progra m me d ph one numbers.

To turn on DTMF Dialing, press:

Add—Option #—14—DONE.

To turn off DTMF Dialing, press:

Delete—Option #—14—DONE.

Option 15: No Activity Time-out (Default = off)

Determines whether the panel sends a No Activity report to a central station or pager when the programmed time period elapses (on), or if the feature is disabled (off).

No activity means control panel, remote handheld, and keychain touchpad buttons have not be pressed and sensors have not been tripped within a specified period of time (except sensors in group 25 ).

The time-out can be set from 02 - 24 hours. All entries must be 2 digits.

Page 20

Programming

To set No Activity Time-out, press:

Add—Option #—15—02 - 24—DONE.

To turn off No Activity Time-out, press:

Delete—Option #—15—DONE.

Option 16: Auto Phone Test (Default = off)

Determines whether the panel automatically performs a periodic phone test (on) or not (off).

The test interval can be from 001 - 254 days. Entries must be 3 digits. The time of day the panel performs the test is determined by Option 72: Super vi s or y Time, which must be turned on for this feature to work.

Note

For UL 1635 listed systems, Auto Phone Test must be set to 001 days.

To set Auto Phone Test, press:

Add—Option #—16—001 - 254—DONE.

To turn off Auto Phone Test, press:

Delete—Option #—16—DONE.

Option 17: Dialer Delay (Default = off)

Determines whether the panel delays dialing programmed phone numbers be fore se nding r eports (on ), or if dialin g begin s immediately (off).

If Option 21: Opening (Disarming) Reports is on, the panel does not delay dialing if the system is disarmed before the delay time expires. The panel dials immediately for both the alarm and opening report.

Note

Regardless of this optio n setting, the panel always dials immediately for alarms from sensors in groups 0-8, 26, for alarms triggered by the control panel or remote handheld touchpad emergency buttons, and for programming, AC power fail ure, and low battery repor ts.

The delay time can be set from 005 - 254 seconds (015 to 045 if Option 69: SIA Limits is on). Entries must be 3 digits.

Note

For UL installations, th e Dialer De lay must n ot ex ceed 45 seconds.

Option 18: Alarm Cancel Report (Default = 005

minutes)

Sets the time frame that determines whether the panel reports an alarm cancel message to the central station.

If the system is disarmed from an alarm state within the programmed time, the panel sends an alarm cancel message to the central station. An alarm cancel message is not reported if the system is disarmed after the programmed time expires.

The time can be set from 005 - 255 minutes. Entries must be 3 digits. When set to 255, the panel always reports alarm cancel messages. Turning off this option disables alarm cancel reporting.

To turn on Alarm Cancel Report, press:

Add—Option #—18—005 - 255—DONE.

To turn off Alarm Cancel Report, press:

Delete—Option #—18—DONE.

Option 19: RF Timeout (Default = 12 hours)

Determines the time period the panel must receive at least one supervisory s ignal from learned s ensors before identifying a sensor failure and sounding trouble beeps. Any sensor failure is reported immediately and again at the supervisory time (Option 72: Supervisory Time).

The timeout ca n be set from 02-24 hours. Entries must be 2 digits.

Note

Setting this feature to 2 hour s (0 2) m ay cause false reports.

For UL 985 and 1635 listed sy st em s, RF Timeout must be set to 4 hours (04). For UL 1023 listed systems, RF Timeout must be set to 24 hours (24) .

To change RF Timeout, press:

Add—Option #—19—02 - 24—DONE.

To reset RF Timeout (return to default), press:

Delete—Option #—19—DONE.

Option 20: Manual Phone Test (Default = on)

To set Dialer Delay, press:

Add—Option #—17—005 - 254—DONE.

To turn off Dialer Delay, press:

Delete—Option #—17—DONE.

Determines whether the user can perform a manual phone test to verify communication to a central station/pager (on), or not (off).

To turn on Manual Phone Test, press:

Add—Option #—20—DONE.

To turn off Manual Phone Test, press:

Delete—Option #—20—DONE.

Page 21

Programming

Option 21: Opening Reports (Default = off)

Determines whether the panel sends opening reports to a central station or pager whenever the system is disarmed (on), or not (off).

To turn on Opening Reports, press:

Add—Option #—21—DONE.

To turn off Opening Reports, press:

Delete—Option #—21—DONE.

Option 22: Closing Reports (Default = off)

Determines whether the panel sends closing reports to a central station or pager whenever the system is armed (on), or not (off).

To turn on Closing Reports, press:

Add—Option #—22—DONE.

To turn off Closing Reports, press:

Delete—Option #—22—DONE.

Option 23: Force Armed Report (Default = off)

Determines whether the panel sends a force armed report to a central stat ion or pager if the user bypasses protesting sensors (indirect bypass) when arming the system (on), or not (off).

To turn on Force Armed Report, press:

Add—Option #—23—DONE.

To turn off Force Armed Report, press:

Delete—Option #—23—DONE.

Option 25: CPU Low Battery Report (Default = on)

Determines whether the panel sends a low CPU battery report to the central station when the panel backup battery voltage drops below 5.4 volts (on), or not (off).

Note

For UL listed systems, CPU Low Battery Report must be on.

To turn on CPU Low Battery Report, press:

Add—Option #—25—DONE.

To turn off CPU Low Battery Report, press:

Delete—Option #—25—DONE.

Option 26: Fail to Communicate (Default = on)

Determines wh ether the panel a nd i nter ior sir ens s oun d trou ble beeps if it is unable to successfully send a report to a central station or page r (on), or not (off).

Note

For UL listed systems, Fail to Communicate must be on.

To turn on Fail to Communicate, press:

Add—Option #—26—DONE.

To turn off Fail to Communicate, press:

Delete—Option #—26—DONE.

Option 27: Ring/Hang/Ring (Default = 1)

Determines when the panel answers a remote phone access or Toolbox call. Depending on whether an answering machine exists at the panel location, off-site access to the panel can be done with a series of phone calls or just one.

The following table shows the available settings.

Option 24: AC Power Failure Report (Default = off)

Determines whether the panel sends AC power failure reports to a central station or pager after the programmed time expires (on), or not (off).

When the panel is without AC power for 30 seconds, the panel LEDs turn off. When the panel is without AC power for the programmed time, an AC power failure is reported. The panel reports an AC power restoral when AC power returns to the panel.

The time can be set f ro m 5- 2 54 m i nu t es . En t ries must be 3 digits.

Note

For UL listed systems, AC Power Failure must be set to 15 minutes.

To turn on AC Power Failure Report, press:

Add—Option #—24—005 - 254—DONE.

To turn off AC Power Failure Report, press:

Delete—Option #—24—DONE.

Ring/Hang/Ring Settings

Setting Control Panel answers after:

1 ring/hang/ring or 10 rings 2 ring/hang/ring/hang/ring or 10 rings 3 ring/hang/ring/hang/ring/hang/ring or 10 rings 4 10 rings

Off Disabled—no remote (off-site) access

For off-site access where an answering machine does not exist, the user or ToolBox operator simply calls the panel location once and listens for 10 rings. The panel should answer after the tenth ring.

For off-site access where an answering machine exists, the user or ToolBox operator must perform the following steps:

1. Call the panel location.

2. Let the phone ring once, then hang up.

Page 22

Programming

3. W ai t at least 10 sec onds but not more than 40, then call the panel location again. The panel should answer on the first ring.

If set to 1, perform steps 1 - 3 once. If set to 2, perform steps 1 - 3 twice. If set to 3, perform steps 1 - 3 three times.

To turn on Ring/Hang/Ring, press:

Add—Option #—27—1, 2, 3, or 4—DONE.

To turn off Ring/Hang/Ring (disable remote access), press:

Delete—Option #—27—DONE.

Option 28: No Delay from Keychain Touchpad

(Default = off)

Determines whether a keychain touchpad arms the system with no delay (on) or no t (off).

Note

When this fe ature is on, the system must be di sarmed before entering the premi ses, since it is disabling the Entry Delay. If Option 58: Remote Touchpad Arming is on, keychain touchpads cannot disarm the system.

To turn on No Delay from Keychain Touchpad, press:

Add—Option #—28—DONE.

To turn off No Delay from Keychain Touchpad, press:

Delete—Option #—28—DONE.

Option 29: Panel Piezo Alarms (Default = on)

Determines whether the panel piezo emits alarm sounds (on) or not (off).

Note

For UL listed systems wh er e th is opti on is off, at least one UL listed external audi bl e signal device must be used and Option 53: Hardwire Siren Supervision must be on.

To turn on Panel Piezo Alarms, press:

Add—Option #—29—DONE.

To turn off Panel Piezo Alarms, press:

Delete—Option #—29—DONE.

Option 30: Panel Panic Alarms (Default = on)

Determines whether the panel panic buttons (police, auxiliary, and fire) activate alarms when pres sed (on), or not (off).

To turn on Panel Panic Alarms, press:

Add—Option #—30—DONE.

To turn off Panel Panic Alarms, press:

Delete—Option #—30—DONE.

Option 31: Downloader Enable (Default = on)

Determines whether the panel can be accessed using ToolBox (on), or not (off).

To turn on Downloader Enable, press:

Add—Option #—31—DONE.

To turn off Downloader Enable, press:

Delete—Option #—31—DONE.

Option 32: 300 Baud (Default = on)

Determines whether the baud rate used by the panel for central station or ToolBox communication is 300 bps (on) or 110 bps (off).

To turn on 300 Baud, press:

Add—Option #—32—DONE.

To turn off 300 Baud, press:

Delete—Option #—32—DONE.

Option 33: Audio Verification (Default = off)

Determines whether the system can perform 2-way voice audio sessions wi th a central stat ion operator (on), or not (off).

Note

Panel voice announce m ents are silenced during audio sessions. If the operator does not terminate the sess io n correctly, panel announcements may not occur for up to 90 seconds after the operator hangs up.

Note

If this option is off, Option 47: AVM Mode and Option 48: Panic Ta lk—A V M will not work.

To turn on Audio Verification, press:

Add—Option #—33—DONE.

To turn off Audio Verification, press:

Delete—Option #—33—DONE.

Option 34: Fail to Open Report (Default = off)

Determines whether the panel sends a Fail to Open report to a central station or pager if the system has not been disarmed by the programmed time (on), or not (off).

Note

System time must be set co rr ectly fo r thi s fea ture to work.

To turn on Fail to Open Report, press:

Add—Option #—34—Hours—Minutes—DONE.

To turn off Fail to Open Report, press:

Delete—Option #—34—DONE.

Page 23

Programming

Option 35: Fail to Close Report (Default = off)

Determines whether the panel sends a Fail to Close report to a central station or pager if the system has not been armed by the programmed time (on), or not (o ff).

Note

System ti me mu s t be set co rr ec tl y f or t his fe at ur e t o wo rk .

To turn on Fail to Close Report, press:

Add—Option #—35—Hours—Minutes—DONE.

To turn off Fail to Close Report, press:

Delete—Option #—35—DONE.

Option 36: Sensor Activated Light Lockout Start

Time (Default = off)

Sets the START time that determines when the panel prevents the sensor activated lights feature from turning on sensor activated lights.

Note

System ti me mu s t be set co rr ec tl y f or t his fe at ur e t o wo rk .

When a time value is set (on) and the sensor activated lights feature is on, the panel prevents sensor activated lights from turning on between the programmed start time (this option) and the programmed stop time (Option 37).

Note

Both Options 36 and 37 must have a time programmed for this feature to work correctly.

When both Options 36 and 37 are turned off and the sensor activated lights feature is on, sensor activated lights turn on at all times.

To set Sensor Activated Light Lockout Start Time, press:

Add—Option #—36—Hours—Minutes—DONE.

To turn off Sensor Activated Light Lockout Start Time, press:

Delete—Option #—36—DONE.

To set Sensor Activated Light Loc kout Stop Time , press:

Add—Option #—37—Hours—Minutes—DONE.

To turn off Sensor Activated Light Lockout Stop Time, press:

Delete—Option #—37—DONE.

Option 38: Auto Arm (Default = off)

Determines how long the system protests (announces open/ failed sensors) when attempting to arm with open/failed sensors, before bypassing these sensors and automatically arming the rest of the system.

Note

The panel protests an arming attempt when it has not received a restore (clos e) si gnal from sensors learned into restore-specific sensor groups. Sensors learned into group 26 (Fire) cannot be bypassed. See “Sensor Group Characteristics” in “Appe ndix B” to identify sensor groups with restore signal requirements.

When this option is on, the panel announces all open/failed sensors repeatedly for 4 minutes, then automatically bypasses the open sensors and arms the rest of the system.

Pressing the ARM Doors & Windows button a second time (before the 4-minute time expires) bypasses all open sensors and arms the rest of the system. Pressing this button a third time eliminates the entry delay.

Note

For UL Listed systems, th is opt i on m ust be on.

Note

This option must be on for Option 52: Unvacated Premises to work corr ectly.

To turn on Auto Arm, press:

Add—Option #—38—DONE. When this option is off, the panel announces all open/failed

sensors once, then automatically bypasses the open sensors and arms the rest of the system.

To turn off Auto Arm, press:

Delete—Option #—38—DONE.

Option 37: Sensor Activated Light Lockout Stop

Time (Default = off)

Sets the STOP time that determines when the panel prevents the sensor activated lights feature from turning on sensor activated lights.

Note

System ti me mu s t be set co rr ec tl y f or t his fe at ur e t o wo rk .

When a time value is set (on) and the sensor activated lights feature is on, the panel prevents sensor activated lights from turning on between the programmed start time (Option 36) and the programmed stop time (this option).

Note

Both Options 36 and 37 must have a time programmed for this feature to work correctly.

When both Options 36 and 37 are turned off and the sensor activated lights feature is on, sensor activated lights turn on at all times.

Option 39: Siren Timeout (Default = 4 min.)

Determines how long sirens sound alarms if no one is present to disarm the system.

The time can be set from 002 - 254 minutes. Entries must be 3 digits. When this feature is turned off, sirens sound alarms until the alarm is canceled (system is disarmed).

Note

For UL listed systems, Siren Timeout must be set to at least 4 minutes.

To set Siren Timeout, press:

Add—Option #—39—002 - 254—DONE.

To turn off Siren Timeout, press:

Delete—Option #—39—DONE.

Page 24

Programming

Option 40: Trouble Beeps (Default = on)

Determines whether the panel, X-10, and hardwire interior sirens sound six beeps every minute when a trouble condition occurs (on) or not (off). The following conditions cause trouble beeps:

❑ AC power failure ❑ Low CPU battery ❑ Sensor failure (supervisory) ❑ Sensor trouble (low battery or tripped tamper) ❑ Fail to communicate ❑ No Activity timer has timed out. Trouble beeps continue

for 5 minutes and if the panel does not see activity, trouble beeps stop and the panel reports the no activity to the central station.

Trouble beeps can be silenced by arming or disarming the system, or by pressing the STATUS button. Trouble beeps resume 4 hours later if the trouble condition is not cleared.

Note

For UL listed systems, Trouble Beeps must be on.

To turn on Trouble Beeps, press:

Add—Option #—40—DONE.

To turn off Trouble Beeps, press:

Delete—Option #—40—DONE.

Option 41: Chime Voice (Default = off)

Determines whether the panel announces the sensor number and name (on) or only sounds beeps (off), when the CHIME Doors or CHIME Spec ial Motio n features are on and sensor s in groups 10, 13, and 25 are tripped while the system is disarmed.

To turn on Chime Voice, press:

Add—Option #—41—DONE.

To turn off Chime Voice, press:

Delete—Option #—41—DONE.

Option 42: Speaker Level (Default = 8)

Sets the volume of voice messages from the panel speaker. The volume can be set from 1 (lowest) to 8 (highest). Turning

off this option returns the setting to the default value.

To set Speaker Level, press:

Add—Option #—42—1 - 8—DONE.

To turn off Speaker Level (return to default), press:

Delete—Option #—42—DONE.

Option 43: Numeric Pager/Voice Event Notification

Phone Number (Default = off)

Lets you program up to a 26-digit phone number for numeric pager or voice event notification (on), or delete an existing phone number (off).

When used to call a numeric pager, a 3-digit code appears on the pager display to identify the report. When used to call a remote phone, a person at the remote phone location can hear system voice alarm announcements. See the “Testing” section for more information.

Press Test for each required pause, Add for a *, and Delete for a # (each of which uses one of the 26 available places).

Note

Some pagers may require 3 or 4 additional pauses after the last digit to work correct l y.

To set Numeric Pager/Voice Event Notification Phone Number, press:

Add—Option #—43—Up to 26 digits—DONE.

Note

Pressing DONE is requi re d if yo u enter fewer than 26 digits. The phone number is automatically stored without pressing DONE if all 26 places are used.

To delete Numeric Pager/Voice Event Notification Phone Number, press:

Delete—Option #—43—DONE.

Option 44: Numeric Pager/Voice Event Notification

Phone Mod 3 (Default = 09)

Determines the report content and reporting format when Option 43: Numeric Pager/Voice Event Notification Phone Number is programmed. The following table describes the choices. All entries must be 2 digits.

Phone Mod 3

Setting # Content Format

08 Latchkey, No Activity, Phone Test,

Openings, Closings, Fail to Open/

Numeric

Pager Close, AC Power Restorals/ Failures

09 Sa me as setting 8 plus Alarms Numeric

Pager

10 Alarms only Voice Event

Notification

To set Numeric Pager/Voice Event Notification Phone Mod 3, press:

Add—Option #—44—08, 09, or 10—DONE.

To reset Numeric Pager/Voice Event Notification Phone Mod 3 (return to default), press:

Delete—Option #—44—DONE.

Page 25

Programming

Option 45: Sensor Alarm Restoral Report

(Default = off)

Determines whether the panel r eports sensor al a r m restorals (on), or not (off). The following table describes the possible settings.

Sensor Alarm Restoral Settings

Setting When Restorals are Reported

Off No restoral reporting 1 Immediately after sensor is closed or restored 2 After siren timeout expires 3 When system is disarmed

To turn on Sensor Alarm Restoral Report, press:

Add—Option #—45—1, 2, or 3—DONE.

To turn off Sensor Alarm Restoral Report, press:

Delete—Option #—45—DONE.

Option 46: Fire Shutdown - AVM (Default = off)

Determines whether system sirens are silenced during a 2-way audio session (on) or not (off). Beeps sound every 10 seconds while sirens are silenced.

To turn on Fire Shutdown - AVM, press:

Add—Option #—46—DONE.

Option 48: Panic Talk - AVM (Default = off)

Determines whether the central station operator can talk to the user during a silent alarm (on) or just listen in on the premises (off).

Silent alarms occur when sensors learned into groups 02 or 03 are tripped, when the Panic Code is entered, or when the panel Police button is pressed and Option 74: Silent Panel Police Panic is turned on.

Note

Option 33: Audio Verification must be on for this fea ture to work.

To turn on Panic Talk - AVM, press:

Add—Option #—48—DONE.

To turn off Panic Talk - AVM, press:

Delete—Option #—48—DONE.

Option 49: Arming LEDs Shutdown (Default = off)

Determines whether the panel LEDs (buttons) turn off 30 seconds after the last button press (on), or remain on for the entire arming period (off).

To turn on Arming LEDs Shutdown, press:

Add—Option #—49—DONE.

To turn off Arming LEDs Shutdown, press:

Delete—Option #—49—DONE.

Option 50: RF Jam Detect (Default = off)

To turn off Fire Shutdown - AVM, press:

Delete—Option #—46—DONE.

Option 47: AVM Mode (Default = off)

Determines whether the panel hangs up and waits for a callback from the central station operator before starting an audio session (on), or stays on line with the central station for an instant audio session (off).

Note

Option 33: Audio Verification must be on for this feature to work.

To set AVM Mode to Callback, press:

Add—Option #—47—DONE.

To set AVM Mode to Instant, press:

Delete—Option #—47—DONE.

Determines whether the panel checks for and reports RF interference/jam to the central station (on), or not (off).

If this option is on and the panel receives a constant 319.5 MHz signal, the panel speaker announces “Option 50 detected” and reports the condition to the central station. If this option is off, the panel does not detect an RF jam.

Note

For UL listed systems, RF Jam Detect must be on.

To turn on Arming LEDs Shutdown, press:

Add—Option #—50—DONE.

To turn off Arming LEDs Shutdown, press:

Delete—Option #—50—DONE.

Option 51: 24 Hour Sensor Tamper (Default = off)

Determines whether the system (armed or disarmed) goes into and reports an alarm anytime a sensor tamper switch is tripped (on), or only when the system is armed and a tamper switch of an armed sensor is tripped (off).

Page 26

Programming

To turn on 24 Hour Tamper, press:

Add—Option #—51—DONE.

To turn off 24 Hour Tamper, press:

Delete—Option #—51—DONE.

Option 52: Unvacated Premises (Default = on)

Determines whether the system automatically arms down to level 2 (ARM Doors & Windows) if the user arms the system to a higher level without leaving the premises (on), or remains at the armed level chosen by the user (off).

Note

This feature does work fr om a keychain touchpad.

If this option is turned on and the user arms to level 3 (ARM Motion Sensors) or 4 (ARM Doors & Windows, + ARM Motion Sensors) but does not exit the premises within the Exit Delay time, the panel automatically changes to arming level 2.

Note

Option 38: Auto Arm must be on for this feature to work.

To turn on Unvacated Premises, press:

Add—Option #—52—DONE.

To turn off Unvacated Premises, press:

Delete—Option #—52—DONE.

❑ Changing the access code length changes the Master, Util-

ity 1, and Utility 2 access codes to their respective defaults as described in the following table.

Note

Changing the Access Code Length clears/deletes any User Codes that were previously programmed. If the customer wants the Access Code Length changed, it should be set before programm in g any new (unprogrammed) access codes, whene ver possible

Access Code Length Defaults

Setting Default Code

3Master—123

Utility 1—321 Utility 2—321

4Master—1234

Utility 1—4321 Utility 2—4321

5Master—12345

Utility 1—54321 Utility 2—54321

6Master—123456

Utility 1—654321 Utility 2—654321

Option 53: Hardwire Siren Supervision

(Default = off)

Determines whether the panel monitors hardwired sirens for open or shorted conditions (on), or not (off).

If this option is turned on, sirens connected to the panel terminals require an EOL resistor in the wire circuit (see “Installing the System” for siren supervision wiring). If this option is turned off, EOL resistors are not required whether sirens are connected or not.

Note

For UL listed systems, th is fe at ur e m ust be on and EOL resistors installed. Also for UL List ed systems, this feature must be on if Option 29: Panel Piezo Alarms is off.

To turn on Hardwire Siren Supervision, press:

Add—Option #—53—DONE.

To turn off Hardwire Siren Supervision, press:

Delete—Option #—53—DONE.

Option 54: Access Code Length (Default = 4)

Determines how many digits are in all access codes. Turning on this option lets you set the access code length to 3,

4, 5, or 6 digits. Turning off this option resets the access code length to the default setting, resets Master, Utility 1, and Utility access codes.

Read the following before changing this option.

❑ This option affects all system access codes (Master, Util-

ity 1, Utility 2, Panic, and User).

To change Access Code Length, press:

Add—Option #—54—3, 4, 5, or 6—DONE.

To reset Access Code Length (to default), press:

Delete—Option #—54—DONE.

Option 55: Status Beep Volume (Default = 07)

Determines the panel piezo volume level for status sounds such as arming, trouble, and status beeps.

The volume can be set from 1 (lowest) to 10 (highest). Turning off this option resets the volume to the default setting. Entries must be 2 digits.

To set Status Beep Volume, press:

Add—Option #—55—01 - 10—DONE.

To reset Status Beep Volume (return to default), press:

Delete—Option #—55—DONE.

Option 56: Call Waiting (Default = off)

Lets you progra m up to a 26 -di gi t numbe r o r code that disa bl es call waiting or any other phone service before dialing central station, pager, or voice event notification phone numbers (on). When this option is turned off, the panel dials only the central station or pager phone numbers.

Press Test for each required pause, Add for a *, and Delete for a # (each of which uses one of the 26 available places).

Page 27

Programming

To program Call Waiting, press:

Add—Option #—56—Up to 26 digits—DONE.

Note

Pressing DONE is required if you enter fewer than 26 digits. The phone number is automatically stored without pressing DONE if all 26 places are used.

To delete Call Waiting, press:

Delete—Option #—56—DONE.

Option 57: Supervisory/Tamper Report

(Default = off)

Determines whether the panel sends supervisory reports to a central station as a tamper (on) or a supervisory (off).

Note

This option is typically used only in Europe where a supervisory condition is required to report as a tamper.

To report supervisories as Tamper Reports, press:

Add—Option #—57—DONE.

To report supervisories as Supervisory Reports, press:

Delete—Option #—57—DONE.

Option 58: Remote Touchpad Arming

(Default = off)

Option 60: Secure Arming (Default = off)

Determines whether an access code is required when arming the system (on) or not (off).

This option does not affect keychain touchpad arm/disarm operation.

To turn on Secure Arming, press:

Add—Option #—60—DONE.

To turn off Secure Arming, press:

Delete—Option #—60—DONE.

Option 61: Demo Mode (Default = off)

Determines whether the panel operates as a demonstration model (on) or a st andard panel (off).

Turning on this feature disables low battery supervision and allows the microphone to remain on continuously during an AVM session.

To turn on Demo Mode, press:

Add—Option #—61—DONE.

To turn off Demo Mode, press:

Delete—Option #—61—DONE.

Determines whether keychain and remote touchpads can disarm the system only during exit and entry delays (on), or arm and disarm the system anytime (off).

CAUTION!

If this option and Option 28: No Delay from Keychain Touchpad is on, users cannot enter and /or dis arm using remote touchpads without causing an alarm.

To turn on Remote Touchpad Arming , press:

Add—Option #—58—DONE.

To turn off Remote Touchpad Arming, press:

Delete—Option #—58—DONE.

Option 59: Exit Extension (Default = on)

Determines whether the panel restarts the exit delay time if the user enters the armed premises during the initial exit delay period (on), or not (off).

Turning on this feature allows users to re-enter during the exit delay period, without disarming and then re-arming the system. Turning off this feature requires the user to disarm and re-arm the system.

Note

For UL listed systems, Exit Ext ension must be off.

To turn on Exit Extension, press:

Add—Option #—59—DONE.

Option 62: Supervisory Protest (Default = off)

Determines whether the panel protests arming if it has not received a supervisory signal from any sensor 15 minutes before arming (on) or not (off).

Note

This feature must be turned on f or E uro pean installations, but turned off for U.S. installations.

To turn on Supervisory Protest, press:

Add—Option #—62—DONE.

To turn off Supervisory Protest, press:

Delete—Option #—62—DONE.

Option 63: 24 Hour Time (Default = off)

Determines whether the panel uses a 24-hour clock (on) or 12hour clock (off).

To turn on 24 Hour Time, press:

Add—Option #—63—DONE.

To turn off 24 Hour Time, press:

Delete—Option #—63—DONE.

To turn off Exit Extension, press:

Delete—Option #—59—DONE.

Page 28

Programming

Option 64: No Arm on Panel Low Battery

(Default = off)

Determines whether the system prevents users from arming if a low CPU battery condition exists (on) or not (off).

To turn on No Arm on Panel Low Battery, press:

Add—Option #—64—DONE.

To turn off No Arm on Panel Low Battery, press:

Delete—Option #—64—DONE.

Option 65: No Usage Report (Default = off)

Determines whether the panel sends a No Usage report to the central station if the user has not operated the system before the programmed time expires (on) or not (off). The timer starts each time the system is disarmed.

This is a customer service feature that alerts the central station if a customer is not using their security system. The service provider can then contact the customer to find out why the system is not being used, and help cor r ect any problems fo r the customer.

The time can be set from 001 to 254 days. Entries must be 3 digits.

To turn on No Usage Report, press:

Add—Option #—65—001 - 254—DONE.

To turn on Quick Exit, press:

Add—Option #—67—DONE.

To turn off Quick Exit, press:

Delete—Option #—67—DONE.

Option 68: Swinger Shutdown (Default = on)

Determines whether the panel prevents the same sensor from activating an alarm more than once in a single arming period (on) or not (off).

Note

Swinger Shutdown does not affect sm oke and fire se nsors.

To turn on Swinger Shutdown, press:

Add—Option #—68—DONE.

To turn off Swinger Shutdown, press:

Delete—Option #—68—DONE.

Option 69: SIA Limits (Default = on)*

Determines whether Entry, Exit, and Dialer delay times fall within SIA limits (on) or factory ranges (off).

The following table shows the available settings when this option is on or off.

To turn off No Usage Report, press:

Delete—Option #—65—DONE.

Option 66: External Siren Delay (Default = off)

Determines whether external siren activation is delayed 30 seconds after an alarm activation (on), or if external siren activation is immediate upon alarm activation (off).

To turn on External Siren Delay, press:

Add—Option #—66—DONE.

To turn off External Siren Delay, press:

Delete—Option #—66—DONE.

Option 67: Quick Exit (Default = off)

Determines whether pressing the Disarm button when the system is armed activates the exit delay time to allow exit and reentry without disarming the system (on) or not (off).

This feature is useful if the user wants to step outside briefly and return, such as to get the paper. If the system is armed and the user presses the Disarm button, the panel announces “Exit time on” and sounds exit delay beeps. This allows a designated entry/exit door to be open for up to 2 minutes without causing an alarm. When the door is closed, the beeps stop and the door is armed again.

Note

For UL listed systems, Qui ck Exi t mu st be off.

SIA Limits

Affected

Option

Option 10:

SIA Limits

(Option 69 on)

030-254 sec onds 005-254 seconds

Entry Delay Option: 11

045-254 sec onds 005-254 seconds

Exit Delay Option: 17

015-045 sec onds 005-045 seconds

Dialer Delay

To turn on SIA Limits, press:

Add—Option #—69—DONE.

To turn off SIA Limits, press:

Delete—Option #—69—DONE.

* Not investigated for use by UL.

Factory Ranges

(Option 69 off)

Page 29

Programming

Option 70: Not Available

Option 71: Programming Report (Default = off)

Determines whether the panel sends a report to the central station anytime the programming mode is entered/exited (on) or not at all (off).

The panel sends a report whenever the dealer (Utility 1) or installer (Utility 2) code is used to enter programming mode and another report is sent when the programming session ends (when the cover is closed).

To turn on Programming Report, press:

Add—Option #—71—DONE.

To turn off Programming Report, press:

Delete—Option #—71—DONE.

Option 72: Supervisory Time (Default = 12:00am)

Determines when the panel reports supervisory conditions (sensor failures) and automatic phone tests to the central station.

Note

The panel clock must be set to the correct time for this option and Option 16: Auto Ph one Test to work correctly.

To set Supervisory Time, press:

Add—Option #—72—Hours—Minutes—DONE.

To turn off (disable) Supervisory Time, press:

Delete—Option #—71—DONE.

Option 73: Modem Sensitivity (Default = off)

To turn off Silent Panel Police Panic, press:

Delete—Option #—74—DONE.

Option 75: VOX Mic Gain (Default = 14)

Sets the mic gain (sensitivity) that triggers the voice-activated switching (VOX).

Room size, acoustics, and furnishings where the panel or Interrogator 200 are located will influence the setting. The available settings are 01 (low) - 64 (high). Entries must be 2 digits.

For panels with a built-in microphone, a setting of 14 is recommended. For systems using the Interrogator 200, a setting of 7 should be used.

To set VOX Mic Gain, press:

Add—Option #—75—01 - 64—DONE.

To reset Vox Mic Gain (return to default), press:

Delete—Option #—75—DONE.

Option 76: VOX Gain Range (Default = 64)

Note

This opti on w orks in c onju ncti on wit h Opt ion 75: V OX Mic Gain. It is important to follow the setting recommendations as described to achieve acceptable operation.

Sets the gain range for the voice-activated switching (VOX). The available settings are 01 (low) - 64 (high). Entries must be

2 digits. For best results, this option should be set equal to or greater

than Option 75: VOX Mic Gain. For panels with a built-in microphone, this option should be set to the default value.

To set VOX Gain Range, press:

Add—Option #—76—01 - 64—DONE.

Determines whether the modem sensitivity is set to normal (off) or high (on).

Note

This feature should be used only if the panel experiences consistent trouble reporting to the central station. Otherwise, leave this option off.

To turn on Modem Sensitivity, press:

Add—Option #—73—DONE.

To turn off Modem Sensitivity, press:

Delete—Option #—73—DONE.

Option 74: Silent Panel Police Panic (Default = off)

Determines whether pressing the panel police panic button causes an audible (off) or silent (on) alarm.

Note

For UL Listed systems, th is opt i on m ust be off (audible).

To turn on Silent Panel Police Panic, press:

Add—Option #—74—DONE.

To reset VOX Gain Range (return to default), press:

Delete—Option #—76—DONE.

Option 77: Manual Mic G ain (Default = 64)

Determines the gain level (sensitivity) during 2-way audio sessions, when Option 33: Audio Verification is set to 0 or 1 (Speak).

Room size, acoustics, and furnishings where the panel or Interrogator 200 are located will influence the setting. The available settings are 01 (low) - 64 (high). Entries must be 2 digits.

For panels with a built-in microphone, a setting of 64 is recommended. For systems using the Interrogator 200, a setting of 20 should be used.

To set Manual Mic Gain, press:

Add—Option #—77—01 - 64—DONE.

To reset Manual Mic Gain (return to default), press:

Delete—Option #—77—DONE.

Page 30

Testing the System

Option 78: VOX Receiver Gain (Default = 6)

Determines the receiver gain level during 2-way audio sessions.

If the VOX is switching the speaker on when the central station operator is not talking, lower both this setting and Option 75: VOX Mic Gain setting. If the VOX is not switching the speaker on when the central station operator is talking, raise this setting and lower Option 75: VOX Mic Gain setting.

Note

Changing this setting doe s not affect speaker volume.

This option can be set from 01 - 10. Entries must be 2 digits.

To set VOX Receiver Gain, press:

Add—Option #—78—1 - 10—DONE.

To reset VOX Receiver Gain (return to default), press:

Delete—Option #—78—DONE.

Option 79: Panel Cover Tamper (Default = off)

Determines whether the panel activates a tamper alarm anytime the cover is opened (on), or only when the system is armed (off).

To enter program mode when this option is on, you must first enter the Master Access code, then open the cover and enter program mode wi thin 10 seconds.

Access Codes (1 - 5)

The panel can have up to 5 secondary user access codes. These could be used by children, a baby sitter, or a service person to disarm (or arm if Option 60 is on). These codes cannot be used for programming.

Panic Code

The Panic Code is able to arm, disarm, or subdisarm the panel and send a silent alarm to the Central Station. There will be no indication of an alarm at the panel.

To add a code:

1. Press Add.

2. Press Access Code button. Continue pressing this button

until you hear the access code to be changed.

3. Press DONE.

4. Enter the new access code by using the nu mbered keys. The panel announces the new code.

To delete a code:

1. Press Delete.

2. Press Access Code. Continue pressing this button until you hear the access code to be deleted.

3. Press DONE. The panel announces the code is deleted.

To turn on Panel Cover Tamper, press:

Add—Option #—79—DONE.

To turn off Panel Cover Tamper (return to default), press:

Delete—Option #—79—DONE.

Option 80: Alarm Report Verification (Default = off)

Determines whether the panel verifies successful alarm reports to the central station/pager with the voice message “Phone communication okay” (on), or not (off).

To turn on Alarm Report Verification, press:

Add—Option #—80—DONE.

To turn off Alarm Report Verification (return to default), press:

Delete—Option #—80—DONE.

Programming System Access Codes

Master Access Code

Depending upon how Option 54 is set, the default Master Access Code is 123456, 12345, 1234 (factory default), or 123. This code is used to: disarm the panel, subdisarm the panel, program light control, set the system clock, program the master code, program access codes 1-5, program the panic code, perform a sensor o r phone test, and p r ogram options 1, 2, 3, 31, 36, 37, 41, 42, 43, and 55.

Testing the Sy st em

This section describes how to perform the following test procedures:

❑ Control Panel ❑ Testing sensors ❑ Testing phone communication ❑ Testing central station communications ❑ Testing the X-10 Lamp Modules

You should test the system after installing, after servicing, and after adding or removing devices from the system.

Control Panel

Test the Control Panel by pressing the buttons as described below.

Note

An access code is required when arming if Option 60: Secure Arming is on.

❑ ARM Doors & Windows-The panel arms Doors & Win-

dows. Press twice to eliminate the programmed entry delay. The button will blink when No Entry Delay is on.

❑ ARM Motion Sensors-The panel will arm Motion Sen-

sors. Press twice to turn Latchkey on. The button blinks when Latchkey is on.

❑ DISARM -The panel will prompt you to enter an access

code. Enter the appropriate code and the panel will disarm Doors, Windows, and Motion Sensors.

Page 31

Arming Levels

Arming Level Description of Level

0 Sub-disarms (Master Access and Panic

codes only), and bypasses 24 hour intrusion sensors (Master Access Code only). Fire sensors (group 26) cannot be sub-disarmed.

Testing the System

The panel responds with Sensor test, press again to change or DONE to select.

5. Press DONE.

The panel will prompt you to trip each sensor one at a time. You may follow the panel voice prompting or test the sensors in any order. Use the “Sensor Tripping Instructions” table on the next page to trip sensors.

Sensor Tripping Instructions

1 Disarm the system 2 Arm Doors and Windows 3 Arm Motions 4 Arm Doors, Windows, and Motions

❑ Two beeps verify that Door/Window sensors are

armed.

❑ One beep indicates the system is disarmed ❑ Three beeps verify that Motion Sensors are armed. ❑ Four beeps ver ify tha t both D oor/Window and Motion

sensors are armed.

❑ SYSTEM STATUS-Press to determine system status and

system time.

❑ CHIME Doors-Press to enable two beeps that sound from

interior sirens, panel siren, and the X-10 pow erhorn siren (if set to uni t number 9) when a protected do or or window learned into s ensor g roup 10 or 13 is opene d. If O ption 4 1: Chime Voice is on, the panel speaker also announces the sensor name and number.

❑ CHIME Special Motion- Press to enable three beeps that

sound from interior sirens, panel siren, and the X-10 powerhorn siren (if set to unit number 9) when a Motion Sensor that is programmed as sensor type 25 is activated. If there are no se nsors learned in to sensor group 25, this function will not be available. If Option 41: Chime Voice is on, the panel speaker also announces the sensor name and number.

❑ LIGHTS Time Activated-Press to enable system con-

trolled lights to turn on/off at a scheduled time.

❑ LIGHTS Sensor Activated-Press to enable system con-

trolled lights to turn on for 4 minutes when a specific sensor is tripped.

❑ AUX, POLICE, FIRE-Press and hold or press twice

quickly to activate a non-medical, police, or fire emergency alarm

Sensor Do This

Door/Window Open the secured door or window Freeze Apply ice to the sensor. Do not

Water Press a wet rag or wet finger over

Carbon Monoxide Alarm

Glass Guard Tap the glass 3 or 4 inches from the

Motion Sensor Avoid the Motion Sensor field of

Rate-of-Rise Heat Detector

Shock Tap the glass twice, away from the

Smoke Press and hold the test button until

Panic Buttons Press and hold the appropriate panic

KeyChain Touchpad Press and hold LOCK and

allow the sensor to get wet

both of the round, gold-plated terminals on the underside of the sensor

Unplug the CO Alarm. Plug it back in, then press the TEST/RESET button until the unit beeps 8 times

sensor

view for 5 minutes, then enter its view

Rub your hands together until warm, then place one hand on the detector for 30 seconds

sensor. Wait at least 30 seconds before testing again

the system sounds transmission beeps

button(s) for 3 seconds

UNLOCK simultaneously for 3 seconds

Sensors

We recommend that you test the sensors after all programming is completed and whenever a sensor-related problem occurs.

Note

While the sensor test is a valuable installation and service tool, it only tests sensor operation for the current conditions. You should perform a sensor test after any change in en vironment, equipment, or programming.

1. Place all sensors in their secured (non-alarm) state.

2. Open the panel cover.

3. Enter the appropriate access code.

4. Press Test.

Remote Handheld Touchpad

Press and hold the 2 EMERGENCY buttons simultaneously for 3 seconds

6. Interior sirens and speakers sound transmission beeps and a voice announcement identifi es the tripped s ensor. Each beep represents one RF packet. Count the num- ber of beeps and refer to the “Minimum Beeps” table for minimum requirements. After the beeps, the panel announces, Sensor Name is activated, se nsor status is XX (XX = number of RF packets). The system will continue to prompt for sensors that have not yet been tested. When all sensors have been tested the panel will announce, Sensor test complete, press DONE.

Page 32

Testing the System

Note

If a sensor does not meet th e m in imum transmission beep requirements, refer to th e “If a Sensor Fails the Sensor Tes t” se ct io n of th is manual

Minimum Beeps

Type of Sensor Number of

Beeps

Wireless Intrusion Sensors 7–8 beeps Wireless Smoke & Heat Sensors 7–8 beeps Wireless Environmental/Panic Buttons 7–8 beeps Hardwire Loops 1 Emergency But tons (Remote Handheld

Touchpads only)

7-8 beeps

7. Press DONE. The panel announces, Sensor Test OK.

8. If Cancel or DONE is pressed and the panel has not

heard from all sensors, the panel will respond, Sensor

test canceled or failure.

Improving Sensor/Panel Communication

To relocate a sensor

1. Test the sensor a few inches from the original position.

2. Increase the distance from the original position and retest until an acceptable location is found.

3. Mount the sensor in the new location.

4. If no location is acceptable, replace the sensor.

To replace a sensor

1. Test a known good sensor at the same location.

2. If the transmission beeps remain below the minimum level, avoid mounting a sensor at that location.

3. If the known-good sensor functions, contact ITI for repair or replacement of the problem sensor.

Phone Communication

Perform a phone test to check the phone communication between the panel and the central station.

To perform a phone test or Downloader (DL) phone test

1. Open the panel cover.

2. Enter the appropriate access code.

3. Press Test twice to perform a phone test

Antenna

The panel antenna can be put into the wall to increase the panel RF range.

CAUTION!

Do not do this for installations that require antenna tamper for external antennas.

If a Sensor Fails the Sensor Test

If sirens do not beep when a sensor is tripped, use an ITI RF Sniffer (60-401) test tool to verify that the sensor is transmitting. Constant beeps from the RF Sniffer indicate a runaway (faulty) sensor. Replace t he sensor.

If possible, locate sensors within 100 feet of the panel. While a sensor may have a range of 500 feet or more out in the open, the environment at the installation site can have a significant effect on transmitter range. A change in sensor location may help overcome adverse wireless conditions and can be accomplished by the following:

❑ reposition the sensor ❑ relocate the sensor ❑ if necessary, replace the sensor

To reposition a sensor

1. Rotate the sensor and test for improved sensor communication at 90 and 180 degrees from the original position.

2. If poor communication persists, relocate the sensor.

Press Test three times to perform a DL phone test.

4. Press DONE. The panel confirms that a phone test or

downloader phone test has beg un. When the phone test is complete, the panel will announce Phone Test is OK within 3 minutes. The panel will say Phone test is on three times if you have a pager. Your pager will display 101 101 if the phone test to the pager was successful.

If the test is unsuccessful, the SYSTEM STATUS button will light and the panel will say Phone communication failure within 10 minutes.

If the panel announces Phone communication failure, proceed to the following instructions.

If the phone test fails

1. Check that the panel is connected to the phone jack.

2. Check the phone number programmed into the panel.

3. Perform the phone test again.

4. If the phone test fails again, check the phone connection wiring.

Page 33

Testing the System

Off-Site Phone Operation

Test the system from a remote phone using the commands in the following table.

Remote Phone Operation

System Function Phone Command

DISARM * + CODE + 1 ARM Doors/Windows * + CODE + 2 ARM Motion Sensors * + CODE + 3 ARM Doors/Windows

with No Entry Delay

ARM Motion Sensor s with Latchkey

ARM Doors/Windows and Motion Sens ors

ARM Doors/Windows with No Entry Delay and Motion Sensors with Latchkey

Toggle Lights * + CODE + 0 System Status * + CODE + # + 1 Audio Verification * + CODE + 5 + X (X = a

Terminate Session * + CODE + 9

* + CODE + 2 + 2

* + CODE + 3 + 3

* + CODE + 2 + 3

* + CODE + 2 + 2 + 3 + 3

command from Audio Verification Set)

Pager Communication

Use the following table to determine what the numeric message is reporting.

Pager Reporting Message

Reports Numeric

Message

Phone Test -101 -101 AC Power Restoral -102 -102 AC Power Failure -103 -103 Latchkey -104 -104 No Activity -105 -105 Panic Code -106 -106 Emergency -107 -107 Intrusion -108 -108 Fire -109 -109 Openings -110 -110 Closings -111 -111 Fail to Open -112 -112 Fail to Close -113 -113

Central Station Communication

After performin g sens or and ph one test s, check t hat th e syste m is reporting alarms successfully to the central station.

To test communication with the central station:

1. Call the central station and tell the operator that you will be testing the system.

2. Arm the system.

3. Test each of the wireless panic buttons and trip at least one sensor of each type (fire, intrusion, etc.) to verify that the appropriate alarms are working correctly.

4. When you finish testing the system, call the central station to verify that the alarms were received.

User Codes for Opening and Closing Reports

Arm or Disarm from: Reports as User:

Panel or Remote Handheld Touchpad

Keychain Touchpad 1-24 (sensor number) Master Code 30 Access Codes 1-5 31-35

2-Way Voice Operation

To initiate an audio session, the central station operator must perform the following steps:

1. After the panel has completed reporting the alarm, pick up the CS phone and press the audio session.

2. Press 1 or 0 to speak, 2 for VOX operation, and 3 or 6 to listen.

3. Press 99 to terminate the session.

Note

Panel voice announce m ents a re s ilen ced during AVM sessions. If the operator does not terminate the session correctly, panel announcements may not occur for up to 90 seconds after the operator hangs up.

Note

To conduct an audio session using remote phone access see the Table “Phone Commands for Remote Access” in the “Testing” secti on.

‚ button to start the

Panic Code 36

Page 34

Testing the System

Phone

Button(s)

0-1 Speak

2 VOX operation

Audio Verificatio n Se t

Function

❑ Keychain T ouchpad: Press the LIGHT button repeatedly

to turn all lights on and off. The panel responds with Lights on/off.

❑ Remote Handheld Touchpad: Press the Lights On but-

ton and the unit # of the lamp module using the numeric buttons to test individual lamp modules 2, 4, 6, and 8. The panel responds with Lights # on/off.

X-10 Siren and Lamp Module Functions

3 or 6 Listen

7 Extend session for 90 more seconds

88 Terminates session with call back (the panel

99 Terminates session with no call back

answers on the first ring if called within 5 minutes)

Voice Event Notification

Testing this feature requires two people; one at the alarm site and the other at the location the panel is programmed to call (Options 5 and/or 43). The panel only reports alarms when this feature is set up.

CAUTION!

If the system is m oni tore d b y a c en tral s tati on, contact them first before se tting off any al arm s to avoid a false dispatch.

1. Contact the central monitoring station (if system is monitored) to inform them you are testing the system and not to dispatch authorities.

2. At the system site, put the system into an alarm condition.

3. At the calling location, pick up the phone after it starts ringing. You should hear the panel voice announce “Press star for alarm.”

4. Press

5. After listening to the alarm information, press

‚ and the panel voice identifies the alarm. If

there is more than one alarm in progress, the panel voice identifies all of them.

ƒ to ter-

minate the call.

All sirens turn off when the system is disarmed or when the siren timeout expires. Siren priority is as follows:

1. Fire (highest priority)

2. Intrusion

3. Emergency

If an alarm of greater priority occurs during an alarm of lower priority, the greater priority alarm sirens sound. Fire alarms sound a temporal 3 patter n (0.5 secon ds on, 0.5 se conds of f for three beeps then 1.5 seconds off).

Note

The X-10 Siren must be set to unit #9 t o “hear” emergency alarms.

Alarm Siren and X-10 Light Information

Fire Intrusion Emergency

X-10 Lights Steady Flashing Steady X-10 Siren Steady Steady Alarm beeps Interior &

Panel Siren Exterior Siren Temporal 3Steady

Temporal 3Steady Fast on/off

Important!

You must terminate the call by pressing ƒ. Otherwise, the panel may not disconnect from t he phone line for up to 2 minutes.

X-10 Operation

The following sections describe how to test X-10 Lamp, Siren, Appliance, and Universal Module operation.

Manual Lamp Module Control

❑ Control Panel: Press the Lights On button and the unit #

of the lamp module using the numeric buttons to test individual lamp modules 2, 4, 6, and 8. The panel responds with Lights # on/off. Press the Lights On button twice to turn on all lamp modules. Press the Lights Off button twice to turn off all lamp modules.

Page 35

Emergency Planning

Emergency Planning Floor Plan

Use the following guidelines when drawing an emergency floor plan for the ho m e ow ne r :

❑ Show all building levels. ❑ Show exits from each room (2 exits per room are recom-

mended).

❑ Show the locations of all security system components. ❑ Show the locations of any fire extinguishers.

A smoke detector should

Bedroom

Living

Room

Basement

Hall

Bedroom

be located on each level.

Dining

Room

Living

Room

Basement

Bedroom

Hall

Recreation

Room

Bedroom

Emergency Planning

Dining

Kitchen

Room

Living

Room

Dining

Room

Bedroom

NOTE: Ceiling-mounted smoke detectors should be located in the center of the room or hall, or not less than 4 inches from the wall. When the detector is mounted on the wall, the top of the detector should be 4 to 12 inches from the ceiling.

NOTE: Do not install smoke detectors where normal ambient temperatures are above 100°F or below 40°F. Also, do not locate detectors in front of AC/ Heat registers or other locations where normal air circulation will keep smoke from entering the detector.

NOTE: Additional information on household fire warning is available at nominal cost from: The National Fire Protection Association, Batterymarch Park, Quincy, MA 02269. Request Standard No. NFPA74.

Required smoke detector

Heat detector

Indicates smoke detector is optional if door is not provided between basement and recreation rooms.

Bedroom

Kitchen

Living

Room

Bedroom

Hall

Bedroom

Smoke detectors should be located between the sleeping area and the rest of the family living unit.

In family living units with more than one sleeping area, locate a smoke detector at each area.

8557144a

Figure 13.Diagram of smoke detector locations.

Page 36

Appendix A: Troubleshooting

System Status

How to clear SYSTEM STATUS (Alarm Memory) From a disarmed state press SYSTEM STATUS, listen to the

status message, then press DISARM. Panel announces Siren 1 failure or Siren 2 failure.

❑ Turn option 53 off if a hardwire siren or sensor is not con-

nected.

❑ Check for the correct end-of-line resistor in HWIN 1 and 2

circuits.

Panel announces Low Battery.

❑ Check that panel backup battery is connected.

Panel announces Option 50 Detected.

❑ Option 50 is RF jam dete ct. The contr ol panel has det ected

RF interference.

Panel announces that a sensor is open.

❑ See Sensors section below.

Panel announces System time is not set.

❑ Set the system time.

Control Panel

Sensors

A sensor does not work.

❑ Make sure the battery is fresh and installed correctly. ❑ Check for interference from metal objects. Move or rotate

the sensor.

❑ Move the sensor to a new location.

Door or window is closed, but the panel announces it is open.

❑ Be certain the arro w on the magnet and the guide line on

the transmitter are aligned and within 1/4 inch of each other.

❑ The sensor tamper switch may be open (cover off).

Motion sensors go off continuously.

❑ Be sure the sensor is mounted on a solid surface and the

viewing field is free from sources of changing temperature.

Motion sensor does not respond to motion.

❑ Make sure the sensor battery is fresh and installed cor-

rectly. Wait 2 minutes after installing a new battery to test the sensor.

❑ Adjust the sensor mounting. ❑ Leave th e area for 3 minutes, then retest. ❑ The environment is too hot or too cold. Outdoor sensors

will operate between 32° and 120°F.

❑ Dirt or dust may be causing the probl e m. Wipe the sensor

with a clean, damp cloth.

Panel announces Function not avail ab l e when Chime Doors is pressed.

❑ No sensors are programmed using sensor type 10 or 13.

Panel announces Function not availabl e when Chime Special Motion is pressed.

❑ No sensors are programmed using sensor type 25.

Panel announces Function not availabl e when LIGHTS Time Activated is pressed.

❑ No time activated lights have been programmed.

Panel announces Function not available when LIGHTS Sensor Activated is pressed.

❑ No sensor activated lights have been programmed.

Panel announces Invalid. Sensor already programmed as Sensor Name .

❑ This sensor is already programmed. Delete sensor if not

correctly programmed.

Options (Programmable by the homeowner)

Panel does not beep.

❑ Turn on (add) Option 1.

Latchkey does not function.

❑ Latchkey time (option 3) is not set. Set Latchkey time. ❑ Latchkey is not enabled. Enable Latchkey by pressing

ARM Motion Sensors twice.

❑ The phone number is not programmed properly. Repro-

gram the phone number. (options 13 or 43)

❑ System Time is not set. Set system time.

X-10 Modules

All Lamp Modules or Siren not working.

❑ Be sure the panel transformer is plugged into an outlet that

is not controlled by a switch.

❑ Check that the panel is powered using the line carrier

power transformer.

❑ Ho use code was programmed incorrectly.

One Lamp Module or Siren is not working.

❑ Unplug nearby equipment that may be causing interfer-

ence (light dimmer switches, televisions, appliances with older motors).

❑ Check that the switch on the lamp or appliance is turned

on and remains on.

❑ Make sure the lamp has a working bulb. ❑ Make sure the lamp or appliance is plugged into the

Lamp/Appliance Module, the Module is plugged into the outlet and the outlet is not controlled by a switch.

❑ Make sure the House and Unit Codes are corre ct. ❑ Move the Module to a different outlet that is on the same

phase (branch) of the household electrical circuit as the panel.

Time or sensor activated light not working.

❑ Make sure you have programmed the light to be activated

by a timer or sensor.

❑ Make sure the system clock is set. ❑ Make sure these functions have been enabled by pressing

the LIGHTS Time Activated/Sensor Activated button on the panel. The functions are enabled if the button is lit.

Page 37

Appendix B: System Configuration

Sensor Assignments/Locations

Appendix B: System Configuration

Sensor

No.

01 02 03 04 05 06 07 08 09 10

11 12 13 14 15 16 17 18 19 20 21 22 23 24

Device

Sensor

Group

Sensor Name/Location Notes

Alphabetical Listing of Sensor Names

Attic, Back Door, Back Window, Basement, Basement Window, Bathroom, Bathroom Window, Bedroom, Bedroom Window, Child ’s Room, Child’s Room Window, Closet, Den, Den Window, Dining Room, Dining Room Window, Downstairs, Downstairs Window, Front Door, Front Window, Garage, Garage Door, Garage Window, Guest Room, Guest Room Window, Hallway, Keychain Remote, Kitchen, Kitchen Window, Laundry Room, Laundry Room Window, Living Room, Living Room Window, Master Bedroom, Master Bedroom Window, Medicine Cabinet, Module, Office, Office Window, Patio Door, Phone Communication Mo du l e, P or c h, P or c h Window, Special Chime, System Panic, Touchpad Remote, Upstairs, Upstairs Window, Utility Room

Page 38

Appendix B: System Configuration

Sensor Group Characteristics

Active

Type

00 Fixed Panic: 24 hour audible fix ed emergency button Intrusion I No Yes 1234 01 Portable Panic: 24 hour audible portable emergency buttons Intrusion I No No 1234 02 Fixed Panic: 24 hour silent fixed emergency buttons. Status light w il l not bl in k. Silent I No Yes 01234 03 Portable Panic: 24 hour si le nt portable emergency button s. Status l i ght w i ll not blink. Silent I No No 01234 04 Fixed auxiliary: 24 hour auxil ia ry sensor Emergency I No Yes 01234 05 Fixed Auxiliary: 24 hour emergency button. Siren shut off confi r m s CS report Emergency I No Yes 01234 06 Portable Auxilia ry : 24 hour porta b le auxi lia ry ale rt butto n Emergency I No No 01234 07 Portable Auxiliary: 24 hour porta b le auxi lia ry butto n. Siren shut off confirms CS report Emergency I No No 01234 08 Special Intrusion: such as gun cabinets and wall safes. Intrusion I Yes Yes 1234 09 Special Intrusion: such as gun cabinets and wall safes. Intrusion S Yes Yes 1234 10 Entry/Exit Delay: Entry/Exit Delay that require a standard delay time. Chime Intrusion S Yes Yes 24 13 Instant perimeter : Ex te rior doors and window s . Chime Intrusion I Yes Yes 24 14 Instant Interior: Interior doors Intrusion F Yes Yes 234 15 Instant Interior: Interior PIR motion sensors* Intrusion F No Yes 234 16 Instant Interior: Interior doors Intrusion F Yes Yes 34 17 Instant Interior: PIR motion sensors and Sound sensors* Intrusion F No Yes 34 18 Instant Inte rior Cross Zone: PIR motion sensors* Intrusion F No Yes 34 19 Delayed Interior: interior doors that initiate a delay before going into alarm* Intrusion S Yes Yes 34 20 Delayed Interior: PIR motion sensors that in itiate a delay before going into alarm* Intrusion S No Yes 34 21 Local Instant In terior: 24 h our local ala rm zone protect ing anything th at opens an d closes.

No Report

22 Local delayed interior: same as group 21, plus activatio n in iti at es a delay before going

into alarm. No report.*

23 Local instant Auxiliary: 24 hour local alarm zo ne protecting anything that opens and

closes.‡ No report

24 Local Instant Auxiliary: 24 hour local alarm zone protecting anything that opens a nd

closes. Sirens s hut off at restoral. No repo rt.*

25 Local Special Chime: Notify the user when a door is opened. Sounds emit from a local

annunciator.* No report 26 Fire: 24 hour fire, rate-of-rise heat, and smoke sensors§. Fire I Yes Yes 01234 27 Lamp control or other customer feature. ‡ N o r eport Silent I Yes Yes 01234 28 PIR motion sensor, sound sensor, or pressure mat .‡ No report Silent I No Yes 01234 29 Auxiliary: Freeze and Water Sensors Trouble Beeps I Yes Yes 01234 32 PIR motion sensor or sound sensor‡ No report Silent I No No 01234 34 Carbon Monoxide Alarm Emergency I Yes Yes 01234 35 Entry/Exit Delay Interior PIR Motion Intrusion S No Yes 234

Name/Application Siren Type

Intrusion I Yes Yes 1234

Intrusion S Yes Yes 1234

Emergency I Yes Yes 01234

Three Beeps I No Yes 01234

Delay

Restoral

Levels

Supervisory

* This type is not certified as a primary protection circuit for UL-listed systems and is for supplementary use only.

§ This type is required for UL-listed residential fire alarm applications. ‡ This type has not been investigated by UL.

Delays:

I = Instant Delay (no delay, immediate alarm) S = Standard Delay (alarm sounds after programmed entry delay time) F = Follower Delay (alarm sounds immediately if entry/exit delay is not active, otherwise alarm sounds after programmed entry delay time)

Page 39

Appendix B: System Configuration

Home Control Planning Table*

Module Activated by Time Activated

Unit # Type Location Sensor Entry/Exit Start Time Stop Time

Example Lamp Hall lam p Motion Yes 8 p.m. 10:30 p.m. 1 2 3 4 5 6 7 8

System Access Codes

The factory default settings are 4-digit access codes, but the default codes will change whenever Option 54 (Access Code Length) is reset. The default for each access code length is listed.

System Access Codes

54321,

4321, or

321

54321,

4321, or

321

12345,

1234, or

123

Installer

Settings

Type Default

Utility Access Code 1 654321,

Utility Access Code 2 654321,

Master Acc ess Code 12 3456,

Access Code 1 None Access Code 2 None

Access Code 3 None Access Code 4 None Access Code 5 None Panic Code None

Option Settings

Page 40

Appendix B: System Configuration

Function Default Delete Range Who Can

Change:

Opt. #

01 Panel Piezo Beeps

On Off On/Off U1 U2 M

(must be on for UL listed systems) 02 Panel Voice On Off On/Off U1 U2 M 03 Latchkey Option Off Off 12:00 Midnight -

U1 U2 M

11:59 PM 04 Primary Phone Number None None 26 digits U1 05 Secondary Ph one Number None Non e 26 digits U1 06 Downloader Phone Number None None 26 digits U1 07 Account Number 00000 00000 0 - FFFFFFFFFF U1 U2 08 Phone Lock Off Off On/Off U1 09 Downloader Code 12345 12345 00000-99999 U1 10 Entry Delay

(must be 45 seconds for UL listed systems)

030 sec 005 sec 005-254 sec

030-254 if Option 69

U1 U2

is added 11 Exit Delay

(must be 60 seconds for UL listed systems)

060 sec 005 sec 005-254 sec

045-254 if Option 69

U1 U2

is added 12 Phone Mod 1

000-3 U1

(must be 0 or 1 for UL listed systems) 13 Phone Mod 2 00 00 00-10 U1 14 DTMF On Pulse On/Off U1 U2 15 No Activity Report Off Off 02-2 4 hr s U1 U2 16 Auto Phone Test

Off Off 001-254 days U 1 U2

(must be set to 001 for UL listed systems) 17 Dialer Delay Off Off 005-254 sec

U1 U2

015-045 is Option 69

is added 18 Alarm Cancel 005 O ff 005-255 min U1 U2 19 RF Timeout (SUPSYNC)

12 hrs 02 hrs 02-24 hrs U1 U2 (must be set to 04 for U L 985 & 1635 Listed systems, or 24 for UL 1023 Liste d systems

20 Manual Phone Test On Off On/Off U1 U2 21 Opening Repo rts Off Off On/Off U1 U2 22 Closing Reports Off Off On/Off U1 U2 23 Force Armed Report Off Off On/Off U1 U2 24 AC Power Failure Report

Off Off 005-254 m in U1 U2 (must be added for UL listed systems)

25 CPU Low Battery Report

On Off On/Off U1 U2 (must be added for UL listed systems)

26 Fail to C o mmunicate

On Off On/Off U1 U2 (must be added for UL listed systems)

27 Ring/Hang/Ring 1 Off 1-4 U1 U2 28 No Delay from Key Chain Touchpad Off Off On/Off U1 U2 29 Panel Piezo Alarms

On Off On/Off U1 U2 (must be added for UL listed systems OR a siren must be connected)

30 Panic Alarms On Off On/Off U1 U2 31 Downloader Enable On Off On/Off U1 U2 M 32 300 Baud Central Station C om m unications On 110 Baud On/Off U1 U2 33 Audio Verification Off Off On/Off U1 U2

Installer

Settings

Page 41

Appendix B: System Configuration

Function Default Delete Range Who Can

Change:

Opt. #

34 Fail to Open Off Off 12:00 Midnight -

U1 U2

11:59 PM

35 Fail to Close Off Off 12 :0 0 Midnight -

U1 U2

11:59 PM

36 Sensor Activated Light Lockout Start Time Off Off 12:00 Midnight -

U1 U2 M

11:59 PM

37 Sensor Acti vated Light Lockout Stop Time Off Off 12:00 Midnight -

U1 U2 M

11:59 PM 38 Auto Arm Off Off On/Off U1 U2 39 Siren Time Out

(must be greater than 4 minutes for UL listed systems)

40 Trouble Beeps

04 min Siren never

times out

002 - 254 minutes/

no time out

U1 U2

On Off On/Off U1 U2

(must be added for UL listed systems) 41 Chime Voice Off Off On/Off U1 U2 M 42 Speaker Level 8 8 1-8 U1 U2 M 43 Pager Phone Numb er Off Off 26 digits U1 U2 M 44 Pager Phone Mod 3 9 9 08-10 U1 U2 45 Sensor Alarm Restoral Off (0) Off (0) 0 - 3 U1 U2 46 Fire Shutdown - AVM Off Off On/Off U1 U2 47 Audio Verification Mode Off Off On (Callback)

U1 U2

Off (Instant) 48 Panic Talk - AVM O ff Off On/Off U1 U2 49 Arming LEDs Shutdown Off Off On /Off U1 U2 50 RF Jam Detect

Off Off On/Off U1 U2

(must be added for UL listed systems) 51 24 Hour Sensor Tamper Off Off On/Off U1 U2 52 Unvacated Premises Off Off On/Off U1 U2 53 Hardwire Siren Supervision

Off Off On/Off U1 U2 (must be added for UL listed systems if Option 29 is deleted)

54 Access Code Length 4 4 3-6 U1 55 Status Beep Volume 7 7 1 - 10 U1 U2 M 56 Call Waiting Off Off 1-26 digits/Off U1 U2 57 Supervisory Tamper Report Off Off On/Off U1 U2 58 Remote To uchpad Arming Off Off On/Off U1 U2 59 Exit Extension

On Off On/Off U1 U2 (must be deleted for UL listed systems)

60 Secure Arming Off Off On/Off U1 U2 61 Demo Mode Off Off On/Off U1 U2 62 Supervisory Protes t Off Off On/Off U1 U2 63 24 Hour Clock Off Off On/Off U1 U2 64 No Arm on Panel Low Battery Off Off On/Off U1 U2 65 No Usage Report Off Off 1-254/Off U1 U2 66 External Siren Delay Off Off On/Off U1 U2 67 Quick Exit

Off Off On/Off U1 U2 (must be disa bled for UL listed systems)

68 Swinger Shutdown On Off On/Off U1 U2 69 SIA Limits On Off On/Off U1 70 Not Available

Installer Settings

Page 42

Appendix B: System Configuration

Function Default Delete Range Who Can

Change:

Opt. #

71 Programming Re port Off Off On/Off U1 U2 72 Supervisory Time Midnight Off U1 U2 73 Modem Sensitivity Off

(normal)

74 Panel Police Panic A udio Off

(audible

Off On (high)/Off

(normal)

Off On (silent)/Off

(audible)

U1 U2

75 VOX Mic Gain 14 14 1-64 U1 U2 76 VOX Gain Range 64 64 1-64 U1 U2 77 Manual Mic Gain 64 64 1-64 U1 U2 78 VOX Receiver Gain 06 06 01 - 10 U1 U2 79 Panel Tamper Alarm Off Off On/Off U1, U2 80 Alarm Report Verification Off Off On/Off U1, U2

Installer Settings

Page 43

Specifications

Power Requirements: .....9 VAC, 700 mA

Specifications

Rechargeable Batteries:

Radio Frequency: ............319.5 MHz (60-875)

Nominal Range: ...............500 feet, open-air receiving range

Storage Temperature Range:-29° to140 ° F (-34° to 60° C) Operating Temperature Range: 32° to 122 ° F (0° to 50° C)

Maximum Humidity: ......90% relative humidity, noncondensing

Auxiliary Power: .............Unregulated 5.1 - 12 VDC, power-lim-

6.0 VDC, 1.2 Ah Lead-Acid The battery will last 24 hours with no AC and specified standby load

433 MHz (60-910)

ited to 250 mA (maximum) @ 1 0 VDC

Page 44

Specifications

Quick Reference Table

How to …

Disarm the System

Subdisarm the System

Arm Only - Doors & Windows

Arm Only – Motion Sensors

Arm Doors, Windows & Motion Sensors

Activate No Entry Delay

Activate Latchkey Feature

Activate a Panic Alarm

Check the System Status

Set Doors to Chime

Set Special Motion to Chime

Turn Time Activated Lights On/Off

Turn Sensor Activated Lights On/Off

Open Garage Door or Turn On Special Lights

Turn All Lights On

Turn All Lights Off

Control Panel

Access Code

Disarm

Enter Access Code while system is disarmed

Doors & Windows

Press once

Arm

Motion

Sensors

Press once

Arm

Doors & Windows

Doors &

Windows

Motion

Sensors

Arm

System

Status

Doors

Motion

Chime

Time

Sensor

Lights

Motion

Sensors

Arm

Chime

Special

Lights

Off

Press each button once

Press twice

Press once

Lights

Press once

Press twice

Remote Handheld

Touchpad

Disarm

Enter Access Code while system is disarmed

ARM Doors & Windows

ARM Motion Sensors

ARM Doors & Windows

Press each button once

ARM Doors & Windows

ARM Motion Sensors

SYSTEM STATUS

Access Code

Press once

ARM Motion Sensors

Press twice

Press both Emergency buttons and hold for 3 seconds

Press once

+ Unit #

Press twice

Key Chain Touchpad

Press once

Press twice

Press once (if programmed)

Press 3 times

Press both & hold for 3 second s

Press once

Remote

Phone

Press * + Master Code + 1

Press * + Master Code + 2

Press * + Master Code + 3

Press * + Master Code + 2 + 3

Press * + Master Code + 2 + 2

Press * + Master Code + 3 + 3

Press * + Master Code + # + 1

Press * + Master Code + 0