UTC 1070140-EN, VC-IP-XP3DN-HR, UVC-IP-XP3DN-HR-P, UVC-IP-EVRDN-HR, UVC-IP-EVRDN-HR-P User Manual

UltraView IP Box
Day/Night Range Camera
User Manual

P/N 1070140-EN • REV 1.0 • ISS 05NOV10

Copyright © 2010 UTC Fire & Security. All rights reserved.

Trademarks and

patents

The UltraView name and logo are trademarks of UTC Fire &

Security.
GE and the GE monogram are trademarks of the General Electric

Company and are under license to UTC Fire & Security, 9 Farm
Springs Road, Farmington, CT 06034-4065, USA.

Other trade names used in this document may be trademarks or
registered trademarks of the manufacturers or vendors of the
respective products.

Manufacture

r

UTC Fire & Security Americas Corporation, Inc.

2955 Red Hill Avenue, Costa Mesa, CA 92626-5923, USA
Authorized EU manufacturing representative:

UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands.

Certification

N4131

FCC compliance Class A: This equipment has been tested and found to comply with

the limits for a Class A digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own
expense.

European Union

directives

2004/108/EC (EMC directive): Hereby, UTC Fire & Security declares

that this device is in compliance with the essential requirements and
other relevant provisions of Directive 2004/108/EC.

2002/96/EC (WEEE directive): Products marked with this symbol

cannot be disposed of as unsorted municipal waste in the European
Union. For proper recycling, return this product to your local supplier
upon the purchase of equivalent new equipment, or dispose of it at
designated collection points. For more information see:
www.recyclethis.info.

Contact information

For contact information see our Web site:

www.utcfireandsecurity.com

Content

Introduction 3

Product description 3
Features 3

Installation 4

Installation environment 4
Package contents 4
Cable requirements 4
Setting up the camera 5
Camera description 6
Lenses 6
Mounting the camera 6
Connections 7
Alarm connection 7
Connecting analog cables 8
Setting the camera DIP switches 8
Description of the DIP switch settings 9

System configuration 11

Software requirements 11
Windows Vista and 7 users 11
Accessing the camera over the internet 12
Overview of monitoring and configuring the system 12
Live viewing 13
Monitoring the system 13
Configuring the camera and network 15

Specifications 18
Warranty and contact information 19

Warranty information 19
Contacting support 19

UltraView IP Box Da

y/Night Range Camera User Manual i

ii UltraView IP Box Day/Night Range Camera User Manual

Introduction

Product description

The UltraView IP box day/night range camera uses a digital signal processor
(DSP) to process video signals. The video camera includes a microcontroller to
provide high-quality images with high-color reproduction and sharp pictures.

Product codes:

• UVC-IP-EVRDN-HR

• UVC-IP-EVRDN-HR-P

Features

Camera features include:

• H.264-SVC video compression with multistream capability.

• Super HAD (hole accumulated diode) technology with 470,000 PAL (410,000
pixels NTSC).

• Use of LSI (large scale integration) digital processors to produce 4CIF
resolution images (540 lines of horizontal resolution analog).

• High-resolution picture production using digital signal processors for
horizontal and vertical aperture enhancement.

• Smart digital automatic BLC (back light control).

• Advanced autoexposure system to optimize the amount of light to the imager.

• Internal or line lock external synchronization.

• Long life and high reliability.

• DIP switch control of camera settings.

• Signal-to-noise ratio better than 48 dB.

• Power over Ethernet (PoE) or Isolated switching power 12 VDC or 24 VAC.

UltraView IP Box Da

y/Night Range Camera User Manual 3

Installation

Installation environment

When installing your product, consider these factors:

• Electrical: Install electrical wiring carefully. It should be done by qualified

service personnel. Always use a proper PoE switch or a 12 VDC or 24 VAC
UL listed Class 2 or CE certified power supply to power the camera. Do not
overload the power cord or adapter.

• Ventilation: Ensure that the location planned for the installation of the

camera is well ventilated.

• Temperature: Do not operate the camera beyond the specified temperature,

humidity or power source ratings. The operating temperature of the camera is
between -30 to +50°C (-22 to +122°F). Humidity is below 90%.

• Moisture: Do not expose the camera to rain or moisture, or try to operate it in

wet areas. Turn the power off immediately if the camera is wet and ask a
qualified service person for servicing. Moisture can damage the camera and
also create the danger of electric shock.

• Servicing: Do not attempt to service this camera yourself. Any attempt to

dismantle or remove the covers from this product will invalidate the warranty
and may also result in serious injury. Refer all servicing to qualified service
personnel.

WARNING: To reduce the risk of fire or electronic shock, do not expose the

camera to rain or moisture and do not remove the cover or back.

Package contents

The camera is shipped with the following items:

• The camera assembly

• 1 channel passive video transceiver

• AC power wiring harness

• 150 mm DC jack to terminal adapter

Cable requirements

For proper operation, adhere to the following cable and power requirements for
the cameras. Category 5 cabling or better is recommended. All network cabling
must be installed according to applicable codes and regulations.

4

UltraView IP Box Day/Night Range Camera User Manual

Table 1 below lists the requirements for the cables that connect to the camera.

Table 1: Recommended cable requirements
Cable type Requirements

Video 75 ohm RS-59 coaxial cable with BNC ends
Power 24 VAC cable

Setting up the camera

Note: If the light source where the camera is installed experiences rapid, wide-

variations in lighting, the camera may not operate as intended.

To quickly put the camera into operation:

1. Connect the lens to the camera.

2. Prepare the mounting surface and mount the camera to the wall/ceiling using
the appropriate fasteners.

3. Connect the cables to the camera.

4. Connect a CCTV monitor to the system to program the camera.

5. Set the camera’s DIP switches, which are located on the rear of the camera,
to suit the camera’s location. See “Setting the camera DIP switches” on page

8.

6. Set up the camera’s network and streaming parameters so that the camera
can be controlled over the network. See “Accessing the camera over the
internet” on page 12.

UltraView IP Box Da

y/Night Range Camera User Manual 5