Page 1
User Manual
7940 Rodeo Trail, Ste 360
Mansfield, Texas 76063
(817) 297-7745
1
Page 2
Table of Contents
2
Quick Start _______________________________________________________
5
Function
Steam ________________________________________________________ 6
Va cu u m _ _ __ _ __ _ __ _ __ __ _ __ _ __ _ __ _ __ _ __ _ __ _ __ __ _ __ _ __ _ __ _ __ _ __ _ _ 6
Extraction _____________________________________________________ 7
Shut Down ____________________________________________________ 7
Assembly (Collection Tank, Handle, and Tool Box) ________________________
8
Tool s
& Accessories _______________________________________________ 9
Maintenance
_____________________________________________________
10
Trouble Shooting __________________________________________________
11
Error Codes ______________________________________________________
11
Descaling ________________________________________________________
12
Notices __________________________________________________________
14
Warr anty & Repair _________________________________________________
15
Tec h ni ca l D at a
Steam Max pressure 117 PSI
Boiler Max temperature 338°F
Dimensions (in) 15 x 28 x 37
(W x L x H)
Shipping Weight 98 pounds
Power cord Length 10 ft.
Hose Length 10 ft.
Tan k Ca pa ci ti es
Steam reservoir tank: ½ gal
Extraction reservoir tank: ½ gal
Vacuum collect io n tank .8 gal
Voltage 120V 60Hz
AMPS: 13.5
Maximum power 1800W
Max Boiler Powder 1000 + 700W
AISI 304 stainless steel boiler
Vacuum motor power 1200W max
Vacuum Water Lift 83 inches
Vacuum Air flow 47CFM
Page 3
Steam Pressure
Boiler
Tem pe rat ur e
Boiler Heating
(Flashing when heating)
Low Water
Extraction
Steam
Descaling
Water Reservior Tanks
Drain Plugs
Cleaning Accessories
Console
Hose Connection
ON/OFF
VA C U U M EXTRACTION
Exhaust Cover
Iron (not included)
Collection Tank
LED Colors:
Green = Low Vacuum
Orange = Medium Va c uu m
Red = High Va cu u m
3
Boiler Cap
Page 4
Plug into Electrical Outlet
Ø The Blue Evolution should be the
only appliance plugged into the
electrical outlet.
Ø If an extension cord is required:
Ø 10 gauge minimum
Ø 50ft maximum length
Ø The Blue Evolution will power up
and then turn OFF. This is normal.
Ø Push the ON/OFF Button to turn-on.
Look foward to it.
Assembly / preparation
Filling the fi lter bowl
Your appliance is fi tted with a hygienic water fi lter. You must
fi ll the fi lter bowl with water before starting, in order to bind
the extracted dirt in the water and to clean the suctioned air
in the water bath as well.
• Loosen the clips on the right and left of the fi lter bowl and
remove from its slot.
• Re-insert the fi lter bowl, ensuring the switch cam on the
cover is in the correct position.
WARNING:
The appliance can suck in up to approx. 1.5 litres of liquid.
If you exceed this amount, the fi ll level sensor will stop suc-
½
gallon
capacity
for each
tank
Extraction Steam
Look foward to it.
• Re-insert the fi lter bowl, ensuring the switch cam on the
cover is in the correct position.
WARNING:
The appliance can suck in up to approx. 1.5 litres of liquid.
If you exceed this amount, the fi ll level sensor will stop suc-
tion automatically and LED
D
(page 2) on the display will
fl ash.
INFO:
If you only wish to suction liquid, such as accidental water
spills, it is not necessary to fi ll the appliance's fi lter bowl with
water.
When sucking liquids, the MAX. capacity in the container is
approx. 4 litres.
Inserting the steam suction hose
• Insert the connector of the steam suction hose into the
socket until you hear the click of the safety hook.
• To remove the hose from the appliance, press release but-
ton
A
and pull on the connector.
A
ON/OFF
Ø Add water to the vacuum collection
tank to the fill line and re-attach.
(See page 8)
Add Water
Before turning ON the Blue Evolution
Ø Remove tank caps and add water to
the steam and extraction tanks.
Ø Replace tank caps.
Steam (page 6)
Ø Squeeze the RED trigger
to release steam.
Va cu u m (p a ge 6)
Ø Push the button on the
handle.
Extraction (page 7)
Ø Push button on hose
handle.
Blue Evolution is Ready when:
Ø Te mpe rat ure ≥ 330 ℉
Ø It will take 10 minutes for the steamer
to heat and reach working
temperature.
Insert Hose & Select Cleaning
Attachment
Ø Lock front wheels.
Ø Insert the hose and press until you
hear it click.
Quick Start-Up
4
Cleaning Functions
Page 5
Ø The steam symbol will illuminate
on the console signaling the Blue
Evolution is in Steam Mode.
Ø This symbol will start flashing,
signaling the boiler is heating.
Ø Squeeze the RED trigger on the hose
handle to release steam.
Ø Steam Pressure can be increased (+)
or decreased (-) on the side of hose
handle.
Steam Pressure Setting:
Ø 3 – Heavy soil or grease
Ø 2 – Recommend for most cleaning
Ø 1 – Light soil / Delicate surfaces
Steam Pressure
Adjustment
The wet/dry vacuum on the Blue
Evolution can be used independently or
with the Steam and Extraction. Utilize
the vacuum to reduce surface moisture
while cleaning.
Ø Fill the collection tank with water
before using the vacuum (see page 8).
Ø Do not exceed the GREEN max fill
line on the tank.
Ø The vacuum has three suction
settings indicated by the color of the
LED light on the console.
Ø Suction can be increased (+) or
decreased (-) on the side of hose
handle.
Green = Low Suction
Orange = Medium Suction
Red = High Suction
The Blue Evolution vacuum tank can
hold ½ gallon of water. If you exceed
this amount the suction will stop and the
LED will blink.
Ø Activate the Va c uu m by
pushing the symbol on
the hose handle
This symbol will flash during
operation indicating the Blue Evolution
is reheating.
Steam Trigger
Steam Vacuum
5
1
3
2
Steam Pressure
setting
Blue Evolution is Ready when:
Ø Te mpe rat ure ≥330 ℉
Ø It will take 10 minutes for the
steamer to heat and reach working
temperature
Page 6
The Blue Evolution’s Extraction feature
allows the user to clean with hot water.
Extraction increases cleaning
performance, and when used with the
Vacuum, leaves a relatively dry surface.
Ø Activate the Extraction by pushing
the button on the hose handle.
Ø Turn ON the Va cu u m by pushing
vacuum symbol on the hose
handle.
Ø The symbol will illuminate on
the display while the Blue Evolution
is in Extraction mode.
Ø You w il l he ar t he p ump w he n
activated.
Ø Extraction spray can be increased or
decreased in 10% increments by
pushing button on the console.
Ø Default Setting: 60%
Ø 010 - Lowest Setting minimum
amount of water
Ø 100 - Highest Setting Maximum
amount of water
Ø To t urn OFF the Extraction and
return to Steam only, push the
button on the hose handle.
Va cu u m
Extraction
Extraction Shut Down
After Each Use:
It is important to clean accessories and
brushes.
Ø Run the vacuum for 30 seconds to
remove any water from the hose.
Ø Use hot soapy and water to clean
brushes and nozzles.
Ø Empty and use hot soapy water to
clean the collection tank and
remove all debris.
Ø If using the Blue Evolution on an
extremely dirty or greasy surface,
clean hose after use by activating
the vacuum mode and suck water
through the hose on low suction.
Ø If working in a healthcare
environment, the hose can be
cleaned with a disinfection
solutions.
Every 3 Months
Ø Check Boiler cap and descale (see
Page 13).
Ø Descale the reservoir tanks and
boiler. (see page 12).
Ø Check HEPA filter clean or replace.
(see page 10).
Ø Check O-Rings on hose and
extension wands. If damaged,
replace.
Every Year
Ø Replace HEPA filter
Ø Change the O-Rings on the hose
and extension wands (page 10)
6
Page 7
Assembly
Collection Tank
Assembly
7
The collection tank can hold ½ gallon of water. If you exceed this amount, the
fill level sensor will stop suction and the warning display will flash.
Look foward to it.
• Re-insert the fi lter bowl, ensuring the switch cam on the
cover is in the correct position.
WARNING:
The appliance can suck in up to approx. 1.5 litres of liquid.
If you exceed this amount, the fi ll level sensor will stop suc-
tion automatically and LED
D
(page 2) on the display will
fl ash.
INFO:
If you only wish to suction liquid, such as accidental water
spills, it is not necessary to fi ll the appliance's fi lter bowl with
water.
When sucking liquids, the MAX. capacity in the container is
approx. 4 litres.
Inserting the steam suction hose
• Insert the connector of the steam suction hose into the
socket until you hear the click of the safety hook.
• To remove the hose from the appliance, press release but-
ton
A
and pull on the connector.
A
Ø Remove by pulling latches out, located on
the sides of the tank, and slide off.
Ø Remove the lid and fill the tank with water to
the GREEN fill line.
Ø Secure the lid to the tank before re-installing.
Ø To i nst all the tan k, pul l o ut the la tches an d s lid e
tank onto the back of the Blue Evolution.
Ø Use the latches to lock tank in place. It should
slide smoothly and fit tightly.
Accessory Box
The accessory box fits securely on the
handle using two fixed knobs. Tighten
by turning knobs clockwise.
Ø Attach screw knobs
located on each side
Ø Sits in groove on
handle
Push Handle
Ø Attach by placing over fixed screw studs
located on each side and secure with the 2
small knobs. Use the washers with small
knobs.
Ø Secure handle
with the larger
knobs, by turning
clockwise until
tight.
Page 8
Carpet, Upholstery, and mattress
Glass, windows, and mirrors
Pre-Cleaning in heavy soiled
area
Rubber tip with brush
Part # 802102
Nylon Brush
Part # 802015
Carpet, upholstery, and mattress
No Brush
Rubber tip with brush
Part # 80202
All Hard surfaces, tile, and wood
Small Extraction
Nozzle
Part # 9621
Large Extraction
Nozzle
Part # 9620
______________________________________________________
_
______________________________________________________
_)))-_______
Short Spot-Jet Nozzle
Part # 9612
Long Spot-Jet Nozzle
Part # 9613
Suction Nozzle
Part # 8010
3” Round Brush
Part # 7109
1” Nylon / Part # G0018
1” Brass / Part # G0126
1” Steel / Part # G0125
Accessories
______________________________________________________
Hose
Part # 9618
Extension Wands
Part # 9615
Adaptor
Part # 802210
Floor Brush
Part # 8022
Adaptor must be used to connect the
extension wands to the floor brush
8
No brush
Page 9
Maintenance
Accessory Cleaning
It is important to clean accessories and brushes after each use to maintain cleaning
performance.
Ø Use hot soapy and water to clean brushes and nozzles.
Ø Rinse hose with water after each use by activating the vacuum and sucking
water through the hose.
Ø Empty and use hot soapy water to clean the collection tank and remove all
debris.
HEPA Air Filter
We rec ommen d the HEPA fil ter b e cle an ed mo nthly or w hen t he re is a no ticeabl e dro p
in vacuum suction. The filter should be replaced at least once per year.
Ø Remove the exhaust cover
on underside of the Blue
Evolution by loosening the
center screw.
To clean or replace the HEPA filter:
Ø The HEPA filter is located on
the back of the exhaust cover.
9
Pos.(3)
Check the O-rings on the safety handle for damage:
Pos.(1): 1 O-ring on the suction pipe
Pos.(2): 2 O-rings on the steam spout
Check the O-rings on the connector for damage:
Pos(3): 2 O-rings on the brass spout
Check the O-rings on all extension pipes for damage:
Pos.(4): 1: O-ring on the suction pipe
Pos.(1) Pos.(2)
Look foward to it.
Pos.(3)
Check the O-rings on the safety handle for damage:
Pos.(1): 1 O-ring on the suction pipe
Pos.(2): 2 O-rings on the steam spout
Check the O-rings on the connector for damage:
Pos(3): 2 O-rings on the brass spout
Checking O-rings on the extension pipes
Check the O-rings on all extension pipes for damage:
Pos.(4): 1: O-ring on the suction pipe
Pos.(5): 2 O-rings on the steam spout
Cleaning, care and maintenance of accessories
Pos.(1) Pos.(2)
You can order a suitable set of O-rings from our online shop at
O-Rings
O-Rings must be checked regularly for damage. If O-rings are damaged or missing,
please call US Steam to purchase replacement rings. (817) 297-7745.
Hose Handle Hose Extension Wands
Look foward to it.
Entkalkungsanleitung B
Care of accessories
It is essential to clean accessory parts after use to maintain the performance and functionality of the
appliance. Te connections on the extension pipes and the safety handle can be sprayed with a
suitable lubricant or silicone spray as required. This will make it easier to change accessory parts.
Checking the O-rings
To avoid damage to the appliance or accessories, the O-rings on the safety handle and the extension
pipes must be checked regularly for damage. The O-rings will last longer if they are coated regularly
with a lubricant/ silicone spray or a non-acidic grease.
Checking the O-rings
Check the O-rings on the safety handle for damage:
Pos.(1): 1 O-ring on the suction pipe
Pos.(2): 2 O-rings on the steam spout
Cleaning, care and maintenance of accessories
Ø Place Blue Evolution on its
side, water may come out if
reservoir tanks are not empty
Ø Clean by using air hose to
blow out dirt and dust. Make
sure to clean both sides of the
filter.
Page 10
PROBLEM SOLUTION
The Blue Evolution does
not turn on.
Ø The Blue Evolution should be the ONLY appliance plugged into the
electrical outlet.
Ø Check the fuse box for tripped circuit breaker.
Ø If using an extension cord it must meet the following requirements:
Ø Use only a 12 gauge / 15AMP rated or higher extension cord.
Ø 25 ft. max length
The Blue Evolution powers ON
after plugging into the electrical
outlet and then turns OFF.
Ø This is normal.
Ø Push the ON/OFF Button on the console to power ON the Blue
Evolution.
During the warm-up phase the
Blue Evolution’s alarm goes off.
Ø The boiler pulled all the water from the steam reservoir tank
Ø Refill the steam reservoir tank
Ø Push the ON/OF button on the console to reset.
No Vacuum Suction
Warning alarm goes off
Ø Empty and clean the collection tank.
Ø Refill with water to the green fill line.
No Vacuum Suction
No warning signals
Ø Collection tank lid is not attached correctly.
Ø Lid must sit flush on the and locked into position.
Ø It’s helpful to attach the lid to the tank before installing.
Ø Check hose for foreign objects or dirt.
Ø Check and replace the HEPA filter as needed.
Error Codes
Will show on console screen
01 – Refill Steam tank
02 – Refill Extraction tank
03 – Boiler did not refill
04 – Collection tank is full
05 - Descale boiler
06 – Replace UVC lamp
07 - High steam temperature
08 - Replace anti-scaling filter
09 – High motor temperature
10 – Service required
Trouble Shooting
10
Page 11
Descaling
Hard water will cause limescale to build up in the boiler.
Limescale can damage the boiler if not removed by
descaling. We recommend descaling the tanks every 60
days or earlier if the warning indicator light starts flashing.
Descale the Boiler Cap
Unscrew the boiler cap by pressing down and turning
counter-clockwise.
① Remove probe and soak in the descaling solution until
all minerals are removed.
② Replace cap and tighten by pushing down and turning
clockwise
.
Look foward to it.
Warning:
Before starting, disconnect from the main power by pulling out oft he plug.
Remove the sound-proofing casing on the underside
of the appliance. To remove, loosen the middle fixing
screw by hand, which will enable you to fold down,
detach and remove the sound-proofing casing.
Place a suitable container under the appliance and
open the drain plug by turning it to the left with the
included Inbus key (label blue ring “Water Only”).
Drain the reservoir and then screw the drain plug back
in and tighten slightly.
Unscrew the probe cap (1) by pressing down and turning
to the left at the same time.
For thorough cleaning and descaling of the probe cap we
recommend: 0.1 litres of beam descaler and 0.5 litres
water (total 0.6 litres of descaling mixture).
Pour the descaling mixture into a suitable container and
put the probe cap into the mixture.
Probe cap (1)
b)
a)
c)
Boiler cap should only be removed when the steam and boiler tanks are
empty and cooled to room temperature.
11
Descaling Solution is a mixture of 2 cups vinegar and 2 cups water.
Use 5mm allen wrench
Ø Extraction (yellow)
Ø Steam (Blue)
Boiler Tank (13mm)
Empty the Boiler Tank
①Place the Blue Evolution on a flat surface.
②Remove the exhaust cover.
③Using a 13mm wrench, remove the boiler
plug.
④Using 5mm allen wrench, remove the water
tank plug (blue).
⑤Tilt steamer backwards and replace drain
plugs.
Ø Boiler plug tightens until it stops turning.
Ø The (blue) steam tank plug has a snug fit
and will NOT stop turning.
⑥You will need to use a catch container.
⑦Place the Blue Evolution upright allowing it
to rest on its wheels.
⑧The boiler tank is now ready for descaling.
Page 12
Descaling
12
Descaling
①The Blue Evolution must be cool and at room temperature.
②Pour the descaling solution into the steam tank.
③Turn ON the Blue Evolution allowing the descaling solution to be pumped into the
boiler.
④When you hear the low water alarm, push the OFF button and let sit for 30
minutes.
⑤Remove the boiler and steam tank plugs allowing the descaling solution to drain
completely.
⑥Replace drain plugs and tighten accordingly.
Rinse Tanks
It is necessary to remove all the scaling solution from the boiler and steam tank before
using. Two rinse cycles may be necessary to remove all the descaling solution.
①Fill the Steam tank with ¼ gallon of tap water and turn ON the Blue Evolution
allowing the water to be pulled into the boiler tank.
①When you hear the low water alarm, turn OFF.
② Remove boiler drain plug emptying all water in the tank. (DO NOT LAY THE
BLUE EVOLUTION ON ITS SIDE)
③Tilt steamer backwards and replace drain plugs.
Ø Boiler plug tightens until it stops turning.
Ø The (blue) steam tank plug has a snug fit and will NOT stop turning.
Ø Replace exhaust cover.
④Refill the extraction and steam tanks with tap water
⑤Blue Evolution is ready for use.
Page 13
Read all instructions before using this steam cleaner.
WA RN IN G : S TE AM G E NE R AT ED B Y TH E BL UE E VO LU TI ON I S EX TR EM LY HO T AN D
WILL CAUSE INJURY IF IT COMES IN CONTACT WITH THE SKIN OR EYES. USE AS
DIRECTED BY THE MANUAL AND ONLY AIM THE STEAM HANDLE AT THE
CLEANING AREA. ART.
WA RN IN G S
Ø DO NOT leave the steam cleaner unattended while plugged in. Turn off all controls and unplug the
electrical cord when not in use, when moving to another location and before servicing.
Ø DO NOT use with a damaged cord or plug. If the steam cleaner is not working as it should, has
been dropped, damaged, left outdoors or dropped into water, call for service before using.
Ø NEVER attempt to disassemble this product in a way not instructed in this manual.
Ø DO NOT handle the electrical plug with wet hands.
Ø DO NOT use near children.
Ø DO NOT pull or carry by cord. Keep cord away from heated surfaces.
Ø Keep body, hands, and feet away from nozzle or brush steam. Steam can cause burns.
Ø ALWAYS set safety switch on hose handle into the locked position when not in use.
Ø Not setting safety switch to locked position could result in an injury.
Ø ALWAYS test a small area before cleaning a large area on any type of surface to make sure no
damage will occur.
Ø DO NOT expose machine to freezing temperatures while not in use.
Ø DO NOT store gasoline or other flammable vapors and liquids in the vicinity of this or any other
appliance.
ELECTRICAL CONNECTIONS
The steam cleaner uses 110 Volts and will pull 13.1 Amps. It should be the only appliance plugged
into an outlet.
Ø Use only a 12 gauge / 15AMP rated or higher extension cord.
Ø Any alteration of electrical cord supply on this steam cleaner will void all warranties.
Ø Once electrical hook-up meets requirements, make sure all switches on front of unit are in the off
position before plugging unit into electrical outlet. For circuit breaker protection, if possible plug
the unit into an outlet isolated from other equipment, or turn the other equipment off while using the
steam cleaner — the combined electrical amperage of other equipment and the steam cleaner
together may cause a circuit breaker to trip.
Ø Always press the power button to OFF before you unplug the unit.
Ø Removing the ground prongs from the power cord will void any and all warranties and can cause
risk of shock or injury
KEEP FOR YOUR RECORDS. THIS MANUAL MUST BE RETAINED FOR FUTURE
REFERENCE. PLEASE READ, UNDERSTAND AND FOLLOW THE INSTRUCTIONS AND
WA RN IN G S CO NTA I NE D IN T H IS M AN UA L BE F OR E U SI NG T H IS VA P OR ST EA M
CLEANER.
In order to reduce the risk of fire, electric shock, personal injury or damage to property, follow these
instructions carefully. When using electrical appliances, basic safety precautions should be followed.
Notices
13
Page 14
Warranty
Your steamer comes with a one year limited warranty which becomes effective on the date of shipment from
US Steam and is granted to the initial customer and is nontransferable. Any claims under this warranty must
be made before the end of the applicable warranty period. During such period if US Steam determines that a
part or system is defective in material or workmanship, US Steam, at its option, will provide you with a
repaired part or replace any part that is covered by the limited warranty. US Steam reserves the right to
substitute functionally equivalent new or serviceable reconditioned parts or systems. US Steam’s
responsibility is limited to repair, replacement, credit or refund, any of which may be selected by US Steam at
its sole discretion. The Warranty does not cover defects or damage arising from the disassembly or attempted
disassembly of your steamer.
The limited warranty covers only defects arising from normal use and does not include malfunctions or failures
arising from: misuse, abuse, neglect, alteration, usage not in accordance with user manual and instructions,
depletion of consumables, acts of nature or damage caused by repairs where such repairs were made without
US Steam’s express approval.
Use of any replacement parts other than authorized US Steam parts voids all warranties and can cause bodily
injury to the operator and damage equipment. Service performed by anyone other than factory authorized
personnel will void warranty.
SERVICE AND SUPPORT
Before you ship your steam cleaner for service, you must call (800) 613-3874 (M-F 9am-4:30pm Central
Time) or contact us through the web at www.ussteam.net our customer service representative will explain how
you must package and ship your Steamer to prevent further damage
RETURN PROCEDURES
Prior to returning the product(s) you must obtain a Return Merchandise Authorization (RMA) by calling (800)
613-3874. No returns will be accepted without RMA #. When packing the Steamer, you must use the
original packing material to prevent damage in shipping. Make sure you include all items and accessories. You
will be responsible for all shipping cost. Send returns to
US Steam
7940 Rodeo Trail, Ste 360
Mansfield, TX 76063
LIMITATIONS
EXCEPT AS SET FORTH HEREIN, US STEAM MAKES NO WARRANTIES, EXPRESSED OR
IMPLIED, AND DISCLAIM AND NEGATE ALL OTHER WARRANTIES, INCLUDING WITHOUT
LIMITATIONS, IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR THE
PARTICULAR PURPOSE AND CONFORMITY TO MODELS OR SAMPLES. SOME JURISDICTIONS
DO NOT ALLOW LIMITATIONS ON IMPLIED WARRANTIES, SO THESE LIMITATIONS MAY NOT
APPLY TO YOU.
GOVERNING LAW, JURISDICTION AND COSTS
THESE LIMITED WARRANTIES ARE INCORPORATED INTO AND ARE ESSENTIAL AND
MATERIAL PROVISIONS OF THE TERMS AND CONDITIONS OF SALE OR SELLER PRODUCTS TO
YOU. ALL DISPUTES ARISING OUT OF OR RELATED TO THE LIMITED WARRANTY SET FORTH
HEREIN (CUSTOMER DISPUTES) SHALL BE GOVERNED BY THE LAWS OF THE STATE OF
TEXAS. THE CUSTOMER HEREBY CONSENTS TO THE JURISDICTION AND VENUE OF THE
STATE COURTS OF TEXAS TO RESOLVE ANY AND ALL CUSTOMERS DISPUTES WITH BOSTON
GREEN GOODS, INC., AND THE CUSTOMER WAIVES ALL DEFENSES TO SUCH JURISDICITON
AND VENUE INCLUDING, BUT NOT LIMITED TO, ANY DEFENSE BASED ON INCONVENIENT
FORUM. IN THE EVENT THE CUSTOMER AND BOSTON GREEN GOODS, INC. ARE UNABLE TO
RESOLVE ANY CUSTOMER DISPUTE, AND ANY COLLECTION ACTION, SUIT OR OTHER
JUDICIAL PROCEEDING IS COMMENCED; THE PREVAILING PARTY IN ANY SUCH ACTION,
SUIT OR PROCEEDING SHALL BE ENTITLED TO RECOVER ITS COSTS AND REASONABLE
ATTORNEY’S FEES INCURRED.
14
Page 15
Restaurant
Hospital
Floors, Kitchen, Grills, & Bathrooms
The Blue Evolution will clean every area of your restaurant without chemicals.
Patient Beds, Wheel Chairs, & Curtains
Steam is a proven killer of virus and infection causing germs. UV-C
reduces airborne bacteria.
Deli’s, Freezers & Butcher
Chemical free cleaning in areas of food storage and preparation.
Desk, Tables, & Partitions
Blue Evolution guarantees a clean, germ-free work environment increasing
productivity and reducing sick days.
Lockers, Mats, & Gym Equipment
Steam kills mold and germs caused by sweaty athletes.
Equipment, Lockers, and Saunas
Kills viruses and germs found on workout equipment and gym floors.
Toy s, P la yg ro un ds , & B eds
The Blue Evolution can clean all areas where kids pass germs. Extreme
cleaning can reduce sick days for kids and employees.
Seats and Floors
The Blue Evolution combines steam and extraction into one system for more
efficient detailing.
A Better Way to Clean
Grocery
Office
School
Gym
Day:Care
Automotive
7940 Rodeo Trail, Ste 360
Mansfield, Texas 76063
(817) 297-7745
Loading...