USSC Grills B2330694, B2330695, B2330693 User Manual

Ce produit peut vous exposer à des produits chimiques, y compris le

monoxyde de carbone, qui est connu dans l'État de Californie pour causer

le cancer, des malformations congénitales et / ou d'autres problèmes de
reproduction. Pour plus d'informations, visitez www.P65warnings.ca.gov

ASSEMBLY AND OPERATING

INSTRUCTIONS

The Irondale

USG890

The Cumberland

USG730

The Hooch

USG350

A MAJOR CAUSE OF FIRES IS FAILURE TO MAINTAIN REQUIRED CLEARANCES (AIR SPACE) TO COMBUSTIBLE
MATERIALS. IT IS OF UTMOST IMPORTANCE THAT THIS PRODUCT BE INSTALLED ONLY IN ACCORDANCE WITH
THESE INSTRUCTIONS.

READ AND SAVE THESE INSTRUCTIONS

Please read this entire manual before installation and use of this pellet fuel-burning appliance.

Failure to follow these instructions could result in property damage, bodily injury or even death.

Contact local building or fire officials about restrictions and inspection requirements in your area.

NOT FOR USE IN LIVING AREAS

FOR OUTDOOR USE ONLY!

CALIFORNIA PROPOSITION 65 WARNING:

This product can expose you to chemicals including carbon monoxide, which
is known to the State of California to cause cancer, birth defects and/or other

reproductive harm. For more information, go to www.P65warnings.ca.gov

United States Stove Company

Manufactured for:

227 Industrial Park Road

South Pittsburg, TN 37380

[phone]

853351C-1403i

DANGER indicates a hazardous situation which, if not avoided, will result in death or serious

injury.

WARNING indicates a hazardous situation which, if not avoided, could result in death or

serious injury.

CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate

injury.

NOTICE indicates practices unrelated to personal injury which, if not avoided, may result in

property damage

GENERAL HAZARD WARNING

FAILURE TO COMPLY WITH THE PRECAUTIONS AND INSTRUCTIONS PROVIDED WITH THIS
GRILL CAN RESULT IN DEATH, SERIOUS BODILY INJURY AND PROPERTY LOSS OR DAMAGE
FROM HAZARDS OF FIRE, EXPLOSION, BURN, ASPHYXIATION, CARBON MONOXIDE POISONING,
AND / OR ELECTRICAL SHOCK.

ONLY PERSONS WHO CAN UNDERSTAND AND FOLLOW THESE INSTRUCTIONS SHOULD USE
OR SERVICE THIS HEATER.

IF YOU NEED ASSISTANCE OR HEATER INFORMATION SUCH AS AN INSTRUCTIONS MANUAL,
LABEL, ETC. CONTACT USSC GRILLS at [phone].

WARNING:
FIRE, BURN, INHALATION, AND EXPLOSION HAZARD. KEEP SOLID COMBUSTIBLES, SUCH AS
BUILDING MATERIALS, PAPER, OR CARDBOARD, A SAFE DISTANCE AWAY FROM THE HEATER
AS RECOMMENDED BY THE INSTRUCTIONS. NEVER USE THE HEATER IN SPACES WHICH
DO OR MAY CONTAIN VOLATILE OR AIRBORNE COMBUSTIBLES, OR PRODUCTS SUCH AS
GASOLINE, SOLVENTS, PAINT THINNER, DUST PARTICLES OR UNKNOWN CHEMICALS.

WARNING: NOT FOR HOME OR RECREATIONAL VEHICLE USE.

Contact your local building officials and/or Fire Marshall for any restrictions on the use of pellet
grills in your area.

WARNING: Never leave the grill unattended while operating.

Disconnect the grill from its power source when not in use.

Safety Information

WARNING:

• NEVER USE GASOLINE, GASOLINE -TYPE LANTERN

FUEL, KEROSENE, CHARCOAL LIGHTER FLUID, OR
SIMILAR LIQUIDS TO START OR "FRESHEN UP" A
FIRE IN THIS APPLIANCE.

• KEEP CHILDREN, CLOTHING, PETS AND

COMBUSTIBLES AWAY FROM HEATER.

• HOT WHILE IN OPERATION. USE CAUTION.

• DISCONNECT THE GRILL FROM ITS POWER SOURCE

BEFORE PERFORMING ANY MAINTENANCE OR
CLEANING THE GRILL. TURNING THE POWER
SWITCH TO "OFF" DOES NOT DISCONNECT POWER
TO THE ELECTRICAL COMPONENTS OF THE GRILL.

• THE GRILL WILL NOT OPERATE DURING A POWER

OUTAGE. IF A POWER OUTAGE DOES OCCUR,
INSPECT THE GRILL FOR UNSAFE BURN CONDITIONS
THAT MAY HAVE OCCURED.

• ALLOW THE GRILL TO COOL BEFORE PERFORMING

ANY MAINTENANCE OR CLEANING.

• THE GRILL TOP AND THE HOPPER ARE HOT DURING

OPERATION. ALWAYS USE HAND PROTECTION
WHEN REFUELING THIS GRILL.

• FOR USE ON NON-COMBUSTIBLE FLOORING OR

PROVIDE FLOOR PROTECTION ADEQUATE TO
PROVIDE EMBER PROTECTION AROUND THIS GRILL.

• KEEP COOKING PELLETS A MINIMUM OF 3 FEET (1

METER) FROM THIS GRILL.

• DO NOT PLACE CLOTHING OR OTHER COMBUSTIBLE

MATERIALS ON OR NEAR THIS GRILL.

• DO NOT OPERATE THIS GRILL UNDER A CEILING OR

OVERHANG.

• THIS GRILL MUST BE GROUNDED.

• PLUG THE GRILL O A 110-120v, 60 Hz GROUNDED

ELECTRICAL OUTLET WITH GFCI PROTECTION.

• DO NOT USE AN ADAPTER PLUG OR SEVER THE

GROUNDING PLUG.

• DO NOT ROUTE THE ELECTRICAL CORD

UNDERNEATH, IN FRONT OF, OR OVER THE TOP OF
THE GRILL.

• DO NOT ROUTE THE THE CORD IN FOOT TRAFFIC

AREAS.

• DO NOT PINCH THE CORD UNDER ANY OBJECT(S).

• A POWER SURGE PROTECTOR IS REQUIRED.

• ALWAYS LOCATE THE GRILL ON A STABLE AND LEVEL

SURFACE.

• DO NOT UNPLUG THE GRILL IF YOU SUSPECT A

MALFUNCTION. TURN THE POWER SWITCH TO "OFF"
AND CONTACT CUSTOMER SERVICE.

• KEEP FOREIGN OBJECTS OUT OF THE HOPPER.

• THE MOVING PARTS OF THIS GRILL ARE PROPELLED

BY HIGH-TORQUE ELECTRIC MOTORS. KEEP ALL BODY
PARTS AWAY FROM THE AUGER WHILE THE GRILL IS
PLUGGED INTO A POWER SOURCE. MOVING PARTS
MAY BEGIN TO MOVE AT ANY TIME AND WITHOUT
WARNING WHENEVER THE GRILL IS PLUGGED INTO A
POWER SOURCE.

• DO NOT USE ACCESSORIES NOT SPECIFIED FOR USE

WITH THIS GRILL BY USSC GRILLS.

WARNING:

Do Not Tamper With The Heater. Have A
Competent Serviceman Make Any Necessary
Adjustments Or Repairs.

WARNING: RISK OF ELECTRIC SHOCK

• EQUIPMENT MUST BE GROUNDED.

• Use only the power (voltage) specified for this
grill. Refer to the model plate on the grill.

• Use only a three-prong grounded outlet with

GFCI protection.

WARNING: Never leave the grill unattended while operating.

Disconnect the grill from its power source when not in use.

WARNING:

• Never block free airflow through the open vents

of this grill

• ALWAYS install grill so that it is not directly
exposed to water spray, rain, dripping water, or
wind.

• ALWAYS disconnect the grill from its power
source when not in use.

Introduction

The entire family of United States Stove Company would like to thank you for purchasing your new pellet burning

grill. At U.S. Stove, we build all of our products with a hands-on approach to detail and quality. Our old world

team of Craftsmen take great pride in their superior workmanship to ensure you have years of trouble free use
out of your pellet grill.

THIS GRILL IS DESIGNED FOR THE USE OF PELLETIZED FUEL THAT IS SPECIFICALLY FORMULATED FOR COOKING. THE
USE OF PELLETS NOT FORMULATED FOR COOKING WILL NOT GIVE SATISFACTORY RESULTS.

Use only wood cooking pellets specified by the manufacturer. It is important to use only cooking pellets that

are dry and free from dirt or other impurities. The cooking pellet industry has established standards for wood
pellet manufacturers. We recommend that cooking pellets used in all U.S. Stove pellet burning grills meet or
exceed the following specifications:

Fines (ne particles) ........................................................................................ Maximum through a 1/8” screen

Bulk Density .......................................................................................................Minimum 40 lbs. per cubic foot

Size .................................................................................................................... Maximum 3/8” Diameter by 1-1/2” length

Ash Content ..................................................................................................... 1% Maximum (Premium grade)

3% Maximum (Standard grade)

Moisture Content ............................................................................................ 8% Maximum

Heat Content................................................................................................... Minimum 8,200 btu’s per hour

U.S. Stove Company cannot control the quality of cooking pellets you choose to use in your pellet grill and
assumes no responsibility for that choice.

YOUR GRILL REQUIRES PERIODIC MAINTENANCE AND CLEANING (SEE "MAINTENANCE"). FAILURE TO MAINTAIN
YOUR GRILL MAY LEAD TO IMPROPER AND/OR UNSAFE OPERATION.

It is important to note that the ash content of the fuel and frequency of operation will determine the frequency
of which you will be required to clean your pellet grill. A high ash fuel may result in daily cleaning, while a low ash
content fuel may result in less frequent cleaning.

Occasionally, impurities in the fuel will cause a hard mass build up in the burn pot of your Pellet Grill. Impurities,
such as silica, can virtually form little glass balls when subjected to the high heat generated in the burn pot. When

allowed to collect, a hard base build up may block air flow through the burn pot, which will significantly affect
the performance and efficiency of your Pellet Grill. INSPECT THE BURNER POT FOR HARD MASS BUILD UP OR

OTHER BLOCKAGE DAILY. IF NECESSARY, ALLOW THE BURNER POT TO COOL THEN CLEAN THE BURNER POT.

REMOVE ACCUMULATED CREOSOTE OR GREASE TO REDUCE THE RISK OF FIRE. When wood pellets are burned
slowly, they produce tar and other organic vapors that combine with expelled moisture to form creosote. The
creosote vapors condense in a relatively cool oven flue and exhaust hood of a slow burning fire. As a result
creosote residue accumulates on the flue lining and exhaust hood. When ignited, creosote makes an extremely
hot fire.

ASHES SHOULD BE PLACED IN A METAL CONTAINER WITH A TIGHT-FITTIMG LID. THE CLOSED CONTAINER OF ASHES
SHOULD BE PLACED ON A NON-COMBUSTIBLE FLOOR OR ON THE GROUND, AT LEAST 25 FEET FROM ANY
COMBUSTIBLE MATERIALS, PENDING FINAL DISPOSAL. WHEN THE ASHES ARE DISPOSED BY BURIAL IN SOIL OR
OTHERWISE LOCALLY DISPERSED, THE ASHES SHOULD BE RETAINED IN A CLOSED CONTAINER UNTIL ALL CINDERS
HAVE THOROUGHLY COOLED. DO NOT PLACE ANY OTHER WASTE IN THE SAME CONTAINER.

WARNING:

STORE COOKING PELLETS A MINIMUM OF 3 FEET (1 METER) AWAY FROM THE PELLET GRILL.
RADIANT HEAT CAN IGNITE THE FUEL.

WARNING: Never leave the grill unattended while operating.

Disconnect the grill from its power source when not in use.

-2-

WARNING: MINIMUM CLEARANCE TO COMBUSTIBLES

Your pellet grill must be installed with clearance to combustibles as shown below.
DO NOT OPERATE THIS GRILL UNDER A CEILING OR OVERHANG.

FOR USE ON NON-COMBUSTIBLE FLOORING.

REAR WALL

24”

SIDE WALL

SIDE WALL

WARNING: RISK OF CARBON MONOXIDE POISONING

• Use this grill only in well-ventilated areas!

• People with breathing problems should consult
a physician before using this grill.

• Early signs of carbon monoxide poisoning
resemble flu-like symptoms such as headaches,
dizziness, and/or nausea. If you have these

symptoms, your grill may not be

working

properly.

12”12”

• Get fresh air at once! Have the grill serviced.

• Some people are more affected by carbon
monoxide than others. These include pregnant
women, those with heart or lung problems,
anemia, those under the influence of alcohol, or
at high altitudes.

• Never use this grill in living or sleeping areas.

WARNING: Never leave the grill unattended while operating.

Disconnect the grill from its power source when not in use.

-4-

Assembly Instructions

UNPACKING:

1. Remove the grill from the carton.

2. Remove all packing materials applied for shipping.

3. Remove and hold all parts and hardware.

4. Inspect for damage. Promptly inform USSC Grills at [phone] of damaged or missing parts.

TOOLS AND MATERIALS NEEDED FOR INSTALLATION

You will need one (1) #3 phillip screw driver for assembly and one (1) 5/8” socket/
wrench to install wheels. Use proper assembly technique. When installing bolts,
start all bolts first and then tighten sufficiently.

STEP 1 - BASE AND PEDESTAL ASSEMBLY

1. Attach the swivel wheels to base using four (4) 1/4”-20 x 1/2” bolts, four (4) 1/4"
lock washers, and four (4) 1/4" flat washers on each wheel.

2. To attach the fixed wheels to the axle, slide on two (2) 3/8" flat washers,

followed by one (1) wheel and one (1) 3/8" flat washer.

3. Secure the wheel to the axle with one (1) acorn nut. Repeat this step to attach
the second fixed wheel to the opposite end of the axle.

4. Assemble the pedestal using the provided six (1/4" - 20 x 3/4" bolts and six (6)
1/4" flat washers. Fasten the bolts to the threaded inserts.

5. Assemble the pedestal to the base using six (6) 1/4" - 20 x 3/4" bolts and six (6)
1/4" flat washers.

6. Tighten all fasteners

change image to show assy sequence:
Nut, washer, wheel, washer (1), axle

Parts List

Description Qty

Pedestal, Right Side 1

Pedestal, Left Side 1

Pedestal, Center 1

Base 1

Caster Wheel 2

Fixed Wheel 2

1/4-20 Bolt x 3/4” 22

Acorn Nut 2

1/4” - 20 X 1/2” Bolt 8

Side Table 1

1/4” Flat Washer 30

1/4” Lock Washer 8

3/8” Flat Washer 4

Wheel Installation

Pedestal and Base Assembly

WARNING: Never leave the grill unattended while operating.

Disconnect the grill from its power source when not in use.

-6-

STEP 2 - GRILL BODY AND PEDESTAL ASSEMBLY

THE ASSISTANCE OF A SECOND PERSON IS STRONGLY RECOMMENDED FOR THIS STEP

Attach main grill body to the assembled pedestal
with six (6) 1/4-20 x 3/4” bolts and six (6) 1/4" flat
washers. Fasten the bolts along bottom of grill
body into the rivet nuts already installed in the
pedestal pieces.

STEP 3 - SIDE TABLE

Attach the side table to the grill body with four (4)
1/4" - 20 x 3/4" bolts and four (4) 1/4" flat washers

STEP 4 - GRILL SURFACE, DRIP PAN, AND FLAME PLATE ASSEMBLY

Place flame plate in bottom of grill body. ENSURE FLAME PLATE IS LEVEL

WARNING: If flame plate is installed incorrectly the pellets may burn back into the
hopper, and/or the grill may smoke excessively during cook mode and may not maintain
set cooking temperature properly.

Place drip pan.
Place main grilling surface on grill mounting bracket. Align with searing station.

USG350 is not equipped with a searing station. Instead, a second grill surface is provided.

WARNING: Never leave the grill unattended while operating.

Disconnect the grill from its power source when not in use.