U.S. Products ADVANTAGE-100H-SC Information & Operating Instructions

O

O

O

ADVANTAGE-100H-SC

EXTRACTOR

INFORMATION

&

OPERATING

INSTRUCTIONS

120V

CAUTION: DO NOT OPERATE MACHINE UNTIL YOU HAVE READ

ALL SECTIONS OF THIS INSTRUCTION MANUAL

IMPROPER USE OF THE MACHINE WILL VOID THE WARRANTY

1. Always use a defoamer when foaming occurs to prevent vacuum motor damage.

2. Connect the machine to a properly grounded outlet of 20 amps or greater.

3. Keep machine from rain and snow, extremes in temperatures, and store in a heated

location. Use the machine indoors. Do not use outdoors.

4. Use approved chemicals only. NO SOLVENTS.

5. Never use water above 130º F/54º C in the solution tank.

56041932

1

3-2010

IMPORTANT SAFETY INSTRUCTIONS

This machine is only suitable for commercial use, for example in hotels, schools, hospitals, factories,
shops and offi ces other than normal residential housekeeping purposes.

When using any electrical appliance, basic precautions should always be followed, including the
following:

NOTE: Read all instructions before using this machine

.

WARNING!

To reduce the risk of fi re, electric shock, or injury:

• Do not leave the machine unattended when it is plugged in. Unplug the unit from the outlet when

not in use and before servicing.

• To avoid electric shock, do not expose to rain or snow. Store, and use, indoors.

• Do not allow to be used as a toy. Close attention is necessary when used near children.

• Use only as described in this manual. Use only the manufacturer’s recommended attachments.

• Never add water over 130º F/54º C to the solution tank.

• Plug must be connected to an outlet on a 20 amp (or greater) circuit breaker.

• Do not use with damaged cord or plug. If the machine is not working as it should, has been dropped,

damaged, left outdoors or dropped into water, return it to a service center.

• Do not pull by the cord, use the cord as a handle, close a door on the cord, or pull the cord around
sharp edges or corners. Do not run the machine over the cord. Keep the cord away from heated
surfaces. To unplug, grasp the plug, not the cord.

• Do not handle the plug, the cord or the machine with wet hands.

• Extension cords must be 12/3 and no longer than 50 feet. Replace the cord or unplug immediately

if the ground prong becomes damaged.

• Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint,
hair, and anything that may reduce air fl ow.

• Keep loose clothing, hair, fi ngers, and all parts of body away from openings and moving parts.

• Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes, or

any health endangering dusts. Do not use to pick up fl ammable or combustible liquids such as
gasoline or use in areas where they may be present.

• Turn off all controls before unplugging.

• Use extra care when cleaning on stairs.

• Connect to a properly grounded outlet only.

• Liquid ejected at the spray nozzle could be dangerous as a result of its temperature, pressure,or

chemical content.

2

INSPECTION:

Carefully unpack and inspect your ADVANTAGE-100H-SC for shipping damage. Each machine is tested
and inspected before shipping. Any shipping damage incurred is the responsibility of the carrier. You
should notify the carrier immediately if you notice damage to the box or to the machine or parts.

CLEANING SOLUTIONS:

We recommend liquid cleaning chemicals. Powder chemicals ma y be used, but unless mixed very thoroughly
they could cause a build-up in the pump, lines, heat exchanger and/or quick disconnects. Any problem
caused by a chemical build-up is not covered by warranty. Use a neutral cleaner with a pH between 5
and 10 to avoid premature wear of the pump, seals, and/or other components.

MAINTENANCE:

For optimum performance fl ush the machine with clear water at the end of each working day. Once a
month, minimum, run a fl ushing compound through the machine to break up any mineral or chemical
build-up that may have formed. The vacuum motor and the pump do not require any scheduled main­tenance; however, the motor may require replacement brushes after 1000 - 1500 hours. Clean the body
with an all-purpose detergent, and protect it with an automobile interior polish. Lubricate the wheels,
castors, and quick disconnects with an all purpose silicone spray.

PARTS AND SERVICE:

Repairs, when required, should be performed by your authorized distributor who maintains an inventory
of original replacement parts and accessories. Call the distributor from whom you purchased this machine

if you need parts and service. Be sure to specify the machine model. Have your serial number handy.

Serial Number: __________________
Model: ADVANTAGE-100H-SC
Purchase Date:_____________

Write the name and phone number of your distributor:
_____________________________________

_____________________________________

(and be sure to register your warranty: go on-line to www.usproducts.com)

3

SWITCH PLATE

O

O

O

MODEL

O

O

O

III

MODEL (1):

This identifi es the model of your
Advantage machine.

2 3

VACUUM SWITCH (2):

This push-button switch turns
on the vacuum. The switch will
illuminate when it is on.

PUMP SWITCH (3):

The pump switch will illuminate when it is activated, and it will turn on the pump.

HEAT SWITCH (4):

The heat switch will illuminate when it is activated and will turn on the heater.

1

YOUR MACHINE

Solution Tank

Access

4

Recovery Tank
Lid

Vacuum Hose

Connection

Recovery

Tank

Drain

Solution
Output

Switches

12” Wheel

Castor

4

SET-UP & OPERATION:

1. Before each job, check your machine and tool(s) for cleanliness and completeness.

2. Fill the holding tank with clear water , and prespray with the detergent of your choice. If you choose

to add a detergent to the solution tank, be sure to mix well, and always follow the use & dilution
instructions on the chemical label.

Although this machine is designed to supply instant hot water, the addition of warm water to the
holding tank would increase heater effi ciency. Never use water above 130º F/54º C in the solution
tank.

3. Turn off all the switches. Plug the power cord into a properly grounded outlet.
IF YOU WANT HEATED SOLUTION: follow Step #4, otherwise go to Step #5.

4. Turn on the Heat switch, and wait two minutes for the heat exchanger to reach temperature.

5. Turn on the pump and spray through your tool a few times to fi ll the lines with solution. Begin

cleaning.

6. Refi ll and empty the tanks as necessary.

7. When fi nished with the job, vacuum all unused solution into the recovery tank, and dump the liquid

from the tank. Clean the tanks and fi lters. Clean the tool and hoses. Store the machine in a
heated location.

AUTO VACUUM SHUTOFF:

When the recovery tank is full, the ball fl oat will shut-off the suction to prevent the machine from
overfl owing.

NOTE: the fl oat may not work if there is foam in the tank. Always use defoamer to prevent
overfl ow.

CAUTION: Always make sure the fl oat cage is clean and the ball can travel
freely before turning on the machine

5