Page 1
Installation
Guide
Preparation
Cutting Instructions
™
To p o
and Tr a n s l u c e n T s™
Ceiling Panels
Pre-Installation, Cleaning, Maintenance
and Cutting Instructions
To p o™ 3-dimensional system and Tr a n s l u c e n T s™ luminous infill panels create contemporary spaces with unique
visual impact in retail, hospitality, office, education and entertainment environments. These systems consist of
pre-formed and flat LEXAN
or USG specialty ceilings suspension system.
Proper preparation and cleaning can help to maintain the panels’ original appearance. Before installation, remove
any dirt and debris from the surrounding area.
Remove masking paper adhesive from the panels by applying naphtha (VM&P) or kerosene with a soft cloth, and
then clean immediately with soap and water. For Translucents Woven, Shimmer or Textiles panels, do not
remove masking before fabrication. If masking is already removed, use a standard masking tape to protect
panel surface. Do not use gasoline. If the panel has static electricity buildup, wash according to instructions below
to prevent the panel from attracting dirt and dust.
Exercise shop safety procedures and wear protective equipment including safety gloves, goggles, and ear and
respiratory protection when fabricating panels. Fabricate panels in a well-lit and ventilated area. Mark the
intended cut, and cut by following the line with either of the recommended power tools.
®
infill panels, flat FRP infill panels, flat PETG panels and a corresponding Do n n® brand
Washing
NOTE–MATERIAL CANNOT BE SCORED AND SNAPPED. Bending the material excessively will discolor the
material and cause irreparable damage. Use recommended power tools as suggested below:
Circular saw:
– 4,000 rpm or greater
– Blade depth to greater than six times the material thickness
– Blade type recommendations
Steel saw blade (for vinyl/paneling), 80 TPI
Jig saw:
– Blade steel-cutting type, greater than 18 teeth per inch
– Cut with saw set in smooth-cut mode or non-oscillating mode (if possible)
Hole saw:
– Follow the above guidelines for preparing the surface
– Drill pilot hole
– Standard hole saw
Washing will reduce static electricity in the panels, helping to prevent attraction to dust. Remove all masking
materials and wash panels with a mild soap or detergent (see Compatible Cleaners on next page) and lukewarm
water, using a clean sponge or soft cloth on a supported work surface. Use paper or cardboard between panel
and work surface. Rinse well with clean water. Dry thoroughly with a chamois or moist cellulose sponge to prevent
water spots. Do not scrub or use brushes. For additional static solutions, treat with anti-static cleaner to eliminate
dirt and dust cling.
To remove fresh paint splashes, grease or smeared glazing compounds, rub panels lightly with VM&P naphtha or
isopropyl alcohol. Wash with warm water and a mild soap or detergent solution. Rinse thoroughly with clean water
and let dry.
Page 2
Compatible Cleaners
Harsh solvents such as methyl ethyl ketone (MEK) or muriatic acid can cause surface degradation and crazing.
Additionally, cleaners such as glass cleaners, acetone, benzene, lacquer thinner, and gritty abrasive scouring
compounds should never be used to clean these panels.
Use only the following mild cleaning agents:
– VM&P naphtha
– Brillianize
®
– JOY
– PALMOLIVE® Dishwashing Liquid
– Novus (acrylic cleaner)
Follow the manufacturer’s instructions, recommendations and safety procedures when using these products.
Polishing Scratches
Limitations
Buff and fill scratches and minor abrasions with one of the following mild polishes:
– MEGUIAR’S
– NOVUS
– PLEXUS
– SC JOHNSON
– JANVIL
– 3M
®
Mirror Glaze Clear Plastic Detailer
®
Plastic Polish (No. 1 or No. 2)
®
Plastic Cleaner Protectant and Polish
®
Paste Wax
®
Plastic Restore and Polish
™
Finesse-It
™
Test the product selected on a small section of one panel, following the polish manufacturer’s instructions,
to determine its effectiveness for your application.
– Do not use abrasive or highly alkaline cleaners.
– Do not scrape panels with squeegees, razor blades or other sharp instruments.
– Do not use benzene, gasoline, acetone, carbon tetrachloride, butyl cellosolve or glass cleaners.
– Do not clean panels in extreme sunlight or at elevated temperatures.
Manufactured by
United States Gypsum Company
550 West Adams Street
IL 60661
Chicago,
Trademarks
The following trademarks
used herein are owned by USG
Interiors or a related company:
o n n , To p o , Tr a n sl u c e n T s . Freon
D
is a trademark of E.I. du Pont
de Nemours and Company.
Joy is a trademark of Procter &
Gamble Company. Lexan is a
registered trademark of General
Electric Company.Meguiar’s is a
trademark of Meguiar’s, Inc.
Novus is a trademark of Novus
Plastic Polish, Ltd. Palmolive is a
trademark of Colgate-Palmolive
Company. Plexus is a trademark
of BTI Chemical Co., Inc. SC
Johnson is a trademark of S.C.
Johnson & Son, Inc. Finesse-it
is a trademark of 3M. Janvil
is a registered trademark of
Janvil Inc.
Notice
We shall not be liable for
incidental or consequential
damages, directly or indirectly
sustained, nor for any loss
caused by application of these
goods not in accordance with
current printed instructions or
for other than the intended use.
Our liability is expressly limited
to replacement of defective
goods. Any claim shall be
deemed waived unless made
in writing to us within thirty (30)
days from the date it was or
reasonably should have been
discovered.
Note
All products described here
may not be available in all
geographic markets. Consult
your local sales office or
representative for more
information.
Safety First!
Follow good safety and
industrial hygiene practices
during handling and installation
of all products and systems.
Take necessary precautions and
wear the appropriate personal
protective equipment as
needed. Read material safety
data sheets and related
literature on products before
specification and/or installation.
IC456/rev. 11-08
©2008, USG Interiors, Inc.
Printed in U.S.A.
Loading...