Page 1
Installation Cut FIBEROCK Brand A
QUA-TOUGH
Interior Panels to size with a utility knife and straight edge. Use a power saw only
if equipped with a dust-collection device. Panels may be cut by scoring and snapping or by sawing, working
from the face side.
When using the score-and-snap method, score the panel twice and snap the panel away from the cut face.
The backside of the panels is then broken by snapping the panel in the reverse direction. If a power-operated
saw is used, a low-RPM unit with 3-1/2 carbide blade is recommended.
When necessary, use a rasp or S
URFORM
®
to smooth cut edges. Holes for pipes, fixtures and other small
openings can be cut out with a saw or a drywall router equipped with a special bit (available from Rotozip
Tool Corporation). When a router is used, hold panels away from the wall.
Contractors installing tile and tile-setting materials should always follow current ANSI specifications,
TCA guidelines and the specifications of the surfacing materials manufacturer.
Framing and Maximum Fastener Spacing
Fastener Spacing
Thickness Framing Spacing Nails Screws
Walls 1/2 16 o.c. 8 o.c. 16 o.c.
1/2 24 o.c. 8 o.c. 12 o.c.
5/8 16 o.c. 8 o.c. 16 o.c.
5/8 24 o.c. 8 o.c. 12 o.c.
Ceilings 1/2 16 o.c. 7 o.c. 12 o.c.
1/2 24 o.c.* — —
5/8 16 o.c. 7 o.c. 12 o.c.
5/8 24 o.c. 7 o.c. 12 o.c.
* Not permitted in wet areas.
Note: for UL fire-rated partition designs, refer to the specific UL design for proper fastener spacing.
Wall Applications 1. Framing – Space wood and steel framing a maximum of 24 o.c. Framing shall be designed not to exceed L360
deflection for tile and L240 for flexible finishes like paint.
2. Cut panels to size with a utility knife and straight edge. Use a power saw only if equipped with a dust-collection
device.
3. Position all ends and edges of panels over framing members, except when joints are at right angles to framing
members, as in perpendicular applications or when end joints are back-blocked.
4. Install panels vertically whenever possible. End joints should be loosely fit. Install panels a minimum of 3/8 above
the floor.Stagger end joints in successive courses with joints on opposite sides of a partition placed on different
studs.
5. Attach panels to framing supports by spacing fasteners not less than 3/8” from edges and ends of panels
and drive as recommended for specified fastening method. Drive fasteners in field of panels first, working
toward ends and edges.
Framing Wood Use corrosion-resistant Type W or Type S buglehead screws or hot-dipped galvanized roofing
nails. Fasteners must be of sufficient length to ensure a minimum 3/4 penetration into wood framing.
Steel Use corrosion-resistant Type S-12 buglehead screws for 25-12 ga steel framing.When using
25 ga steel framing fasteners should be spaced no grater than 8 o.c. Fasteners must be of sufficient length to
ensure a minimum of 3/8 penetration into steel framing.
FIBEROCK
®
Brand
Interior Panels
Application Tips
AQUA
-TOUGH
™
Page 1 of 2
Page 2
SAFETY FIRST!
Follow good safety practices.
Read material safety data
sheets and related literature on
products before specification
and/or installation.
Tub Surrounds 1. Panel Application—After tub, shower pan or receptor is installed, place temporary 1/4 spacer strips or shims
around lip of fixture. Pre-cut board to required sizes and make necessary cut-outs. Fit ends and edges closely
but not forced together. Install board abutting top of spacer strip. Stagger end joints in successive courses.
Fasten panels to wood studs spaced max. 24 o.c. with corrosion-resistant screws or hot-dipped galvanized
roofing nails. For steel studs (14-25 ga.), use corrosion-resistant screws. For fastener spacing requirement,
refer to table on page two.
2. Seal all openings around pipes, fittings and fixtures with waterproof flexible sealant. Allow areas to dry
thoroughly prior to tile application. Wipe excess material from surface of panels. Remove spacer strips but do
not caulk the gap at the bottom of panel.
3. A waterproof membrane (ANSI A118.10) must be over upward-facing horizontal applications in wet areas.
Ceilings Framing Must be capable of supporting the total ceiling system dead load, including insulation, ceramic tile,
bonding materials and panels, with deflection not exceeding L/360 of the span for tiled surfaces.
Panel Application Center end or edge joints on framing. Stagger end joints in successive courses. Fit ends and edges closely but
not forced together. Fasten boards to framing using recommended fastener table on page one.
Joint Tiled Areas Embed DUROCK Brand Joint Tape in latex-fortified mortar or latex-based Type I mastic over he joint. Use the
Treatment same material as specified for tile setting.
Untiled Areas Embed SHEETROCK Brand Joint Tape in SHEETROCK Brand DURABOND Setting-Type Joint Compound and wipe
with a joint knife, leaving a thin coating of joint compound over all joints and interior angles. Complete to
level of finish specified in project requirements.
Interior Follow ANSI Specifications and TCA Guidelines.
Ceramic Tile
Trademarks
The following trademarks
used herein are owned by USG
Corporation or its subsidiaries:
A
QUA-TOUGH,FIBEROCK,DURABOND,
D
UROCK,SHEETROCK,USG.TYPE S
and T
YPE S-12 are trademarks
of ITW Buildex. S
URFORM is a
trademark of The Stanley Works.
Note
Products described here may
not be available in all geographic
markets. Consult your U.S.
Gypsum Company sales office
or representative for information.
Notice
We shall not be liable for incidental or consequential damages, directly or indirectly sustained, nor for any loss caused
by application of these goods
not in accordance with current
printed instructions or for other
than their intended use. Our
liability is expressly limited to
replacement of defective goods.
Any claim shall be deemed
waived unless made in writing
to us within thirty (30) days from
the date it was or reasonably
should have been discovered.
Manufactured by
United States Gypsum Company
125 South Franklin Street
Chicago, IL 60606
800 USG.4YOU (874-4968)
www.usg.com
F252/2-04
©2004, United States Gypsum Company
Printed in U.S.A.
Page 2 of 2
Loading...