US Electronics UY322-EPG User Manual

Download

Page 1

setting up your remote controlbutton functionsbefore you begin

displays help for on-screen display screens

future use

MUSIC/ENTER switches between cable TV and Music Choice™

LAST recalls the last channel that was viewed

FAV cycles through your favorite channels

MUTE turns volume off

P displays the quick function screen

◆ future use

PPV displays pay-per-view options EXIT exits the on-screen display menus INFO displays channel and program information

MENU displays the main on-screen display menu GUIDE displays the program guide

SEL selects various options and tunes programs from the program guide

CURSOR KEYS navigate through on-screen guides (see the highlighted section above)

PAGE +/- pages through on-screen menu and program guide screens

DAY +/- moves the program guide one day forward and backward

EPG RECORD initiates VCR recording through the on-screen menu (if so equipped)

Part Number USE17370,Version 1.1

9804

User’s Guide for the

UY322-EPG

3-in-1 Remote Control

featuring Memory Lock

™

and Predictive Technology

™

Install two

AAA alkaline batteries

as shown here

If you have a TV with a remote control,we recommend that you plug its power cord directly into a wall outlet if available (your cable installer may select an alternate setup).

Make sure to set your TV to channel 2,3, or 4 as directed by your cable company.

Before you can program or operate the remote control, you must install two AAA Alkaline batteries.

Step 1

Remove the battery compartment cover on the

back of your remote control.

Step 2:

Check battery polarity carefully,and install the batteries as shown in the

illustration below.

Step 3:

Replace the battery compartment cover.

installing batteries

The chart below shows the functions of special keys for your cable box and program guide.

See the cable box manual for further details.

INFO

step

Press the [TV POWER] button,then the [SETUP] button on the remote.

Enter the 3-digit TV code for your brand of TV listed in the “TV codes”chart.

Press the [SETUP] button again to save the code.The red indicator light at the upper right-hand corner of your remote will flash 3 times if these steps were followed correctly.

Press the [TV POWER] button again to test the code you‘ve entered.The TV should turn ON or OFF each time the [TV POWER] button is pressed.If the TV doesn’t turn ON and OFF,repeat this TV setup procedure with the next code listed in the “TV codes”chart.

step

Press the [CABLE POWER] button, then the [SETUP] button on the remote.

Enter the 3-digit cable box code listed below.

Press the [SETUP] button again to save the code.The red indicator light at the upper right-hand corner of your remote will flash 3 times if these steps were followed correctly.

Press the [CABLE POWER] button again to test the code you‘ve entered.The cable box should turn ON or OFF each time the [CABLE POWER] button is pressed.If the cable box doesn’t turn ON and OFF,tr y ente ring the code again.

Follow these simple steps to program your remote for your VCR,TV,and cable box.

Before you start

■ Locate the [SETUP] button, which is at the very bottom of the

remote (see illustration at right).

■Manually turn on your VCR,TV,and cable box.

STOP RECORD

PLAY

REW PAUSE

SETUP

FWD

VCR CONTROLS

The setup code for the

GI/Jerrold™ CFT2200™ series

cable box is

002

Jerrold™ is a trademark of GIC corp.

Helpful

Hint

Following the above steps allows the remote to control

volume through your cable box.If you would like volume

to be controlled through your TV,perform step 3 before

step 2.If you have a combination TV/VCR,volume will be

controlled only through the cable box.

N O T E

I N F O

for

your

for

your

cable

box

step

Press the [VCR POWER] button,then the [SETUP] button on the remote.

Enter the 3-digit VCR code for your brand of VCR listed in the “VCR codes”chart on the other side of this manual by pressing the appropriate buttons on the numeric key pad.

Press the [SETUP] button again to save the code.The red indicator light at the upper right-hand corner of your remote will flash 3 times if these steps were followed correctly.

Press the [VCR POWER] button again to test the code you‘ve entered.The VCR should turn ON or OFF each time the [VCR POWER] button is pressed. If the VCR doesn’t turn ON and OFF,repeat this VCR setup procedure with the next code listed in the “VCR codes” chart.

for

your

VCR

vcr controls

These keys operate standard VCR functions.

Operating Note: Press the [RECORD]button

twice to start recording on your VCR.

numeric keypad

These keys allow you to enter the channel

you want to view.You will also use them

to setup the remote

cable box

function keys

See the chart below for a description

of the key functions

After you find the correct code for each device,write the code on the supplied sticker.

Depending on the configuration

of your cable box,certain

functions listed below may or

may not be functional.

N O T E

Memory Lock™is an exclusive technology

that saves the device codes that are programmed into the remote,even when the batteries are removed.

MEMORY LOCK

™

featuring

Cursor Keys

US Electronics provides these function descriptions as a general guide to allow you to become more familiar with your cable box.Refer to your cable box manual for descriptions of specific functions.

www.uselectronics.com

Page 2

AOC 010 | 019 Candle 010 | 031 | 037 | 081 Capehart 035 Citizen 010 | 027 | 031 | 037

038 | 046 | 081

Concerto 037 Conklin 000 Contec 028 | 064 | 077 | 080 Craig 066 | 077 Curtis Mathes 010 | 038 CXC 077 Daewoo 019 | 027 | 040 | 041 | 046 Dixi 011 Dynatech 032 Emerson 019 | 076 | 077

078 | 080 | 087

Envision 010 Fisher 060 Funai 076 | 077 GE 003 | 021 | 023

GE 025 | 034 | 036 Goldstar 012 | 019 |037 Harman Kardon 044 Hitachi 029| 037 | 050 | 054

048 | 058 | 072 | 085

Infinity 006 JBL 006 Jensen 033 JVC 009 | 065 Kloss Novabeam 022 KTV 077 Logik 018 Luxman 037 LXI 056 Magnavox 006 | 010| 017 | 022

024 |049 | 081| 082

Marantz 010 MGA 007 |010 | 019| 061 Mitsubishi 007 |016 | 019

028 |051 | 061

Mitsubishi Monitor 016 MTC 010 |019 | 032| 037 | 038 NEC 010 | 019| 037 |070 Panasonic 002 |006 | 034| 036 | 067 Penney 001 | 003 |010 | 019| 021 | 057 Philco 006 |010 | 019| 020

022 |024 | 081| 082

Philips 006 Pioneer 008 |071 Proscan 003 Proton 019| 026 |035 Quasar 034| 036 |083 Radio shack 027| 068| 077 RCA 001 |003 | 019 |029 Sampo 010 |035 Samsung 010 |019 | 027| 037 | 038 Sanyo 052 |055 | 060| 086 Scott 076 Sears 017 | 055| 056 |057

060 |069 | 076

Sharp 028 | 047| 059 | 068 Sony 005 |015 | 045 Soundesign 019| 081 SSS 019| 077 Sylvania 006 |010 | 020| 022

024 |039 | 081| 082

Tatung 032 Techwood 037 Teknika 007 |018 | 019| 027

031 |037 | 038| 046 073 |076 | 077| 081

TMK 037 |019 Toshiba 060 |056 Universal 021 | 023 Vidtech 019 Wards 006| 010 |018 | 019

020 |021 | 023| 024

068 |076 | 082

Yamaha 019 Zenith 004

Akai 026 | 030| 034| 049 Alba 016 Altec 004 Amstrad 005 ASA 008 |022 Broksonic 061 Canon 001 Craig 028| 064 Curtis Mathes 001 Daewoo 009 | 015 | 016 | 045 Daytron 016 Dual 026 Dynatech 005 | 029 Emerson 005 | 021 |020 |037 | 041 | 046

050 | 058 | 059| 061| 062

Grundig 008 Harman Kardon 023 |043 Hitachi 005| 006| 026 ITT 026 | 049 JCL 001 Jensen 026 JVC 013 | 026 | 040 Kenwood 026| 027| 040 Lloyd 005 Magnavox 001| 008 Marantz 001| 008| 023 Marta 022 MEI 001 MGA 010| 037 Minolta 006 Mitsubishi 010| 037| 063 MTC 005 | 064 Multitech 005| 042 NEC 023 | 026 | 031 |040 Normende 026 Panasonic 001 | 003 Penney 001| 006 |023

Pentax 006 | 038 Philco 001 Philips 008 Pioneer 036| 040 Portland 016 Proscan 007 Quasar 001| 047 RCA 001 | 002| 006| 007 Realistic 001 | 005| 022 | 027

028 | 029| 048| 064

Saba 026 Saisho 046 | 059 Salora 010 Samsung 009 | 032 | 064 Sansui 026 | 040 Sanyo 027 | 028 Schaub Lorenz 026 Scott 009| 062 Sears 006 |022 | 027 | 028 | 035 | 039 Sharp 029 Shintom 042 Sony 014| 017 | 018 |019

Sylvania 001| 010 Symphonic 005 Tatung 026 Teac 005| 026 Teknika 001 | 005| 022| 033 Telefunken 026 Thomson 026 Thorn 026 TMK 021 Toshiba 009| 010| 026 Totevision 022| 064 Uni-Logic 000 Unitech 064 Vector Research 023 Video Concepts 023 Videosonic 064 Wards 005 | 029 | 064 Yamaha 023 | 026 Zenith 018 | 019 |024

❚GE 003 ❚ JVC 009 ❚Magnavox 006 ❚Mitsubishi 007 ❚NEC 010 ❚Panasonic 002 ❚Philips 006 ❚ Pioneer 008 ❚Proscan 003 ❚RCA 003 ❚Sony 005 ❚ Zenith 004

❚GE 007 ❚ Hitachi 006 ❚JVC 040 ❚ Magnavox 008 ❚Mitsubishi 010 ❚ Panasonic 003 ❚NEC 023 ❚Proscan 007 ❚RCA 007 ❚Sony 018 ❚ Toshiba 009 ❚ Zenith 024

television codes

vcr codes

helpful hint

notes

find your

code sticker

here

Device 1 ___________ Code: [ ] [ ] [ ]

Device 2 ___________ Code: [ ] [ ] [ ]

Device 3 ___________ Code: [ ] [ ] [ ]

Device 4 ___________ Code: [ ] [ ] [ ]

ASSEMBLED IN MEXICO

Port Jefferson Station, NY USE17079

Write your device codes below

Once you have found your TV,VCR, and Cable Box codes, write them down for safe keeping on the code sticker that’s inside the battery

cover (see illustration below). Attach the “Quick Programming Instructions” sticker to the outside of the battery cover.

CodeScan

™

troubleshooting guide

Problem

I programmed the remote,but it won’t work my TV,VCR,or Cable Box.

Solution

You may have entered the wrong code (or the correct code might not be listed).Try entering all of the device manufacturer’s codes again,starting with the manufacturer’s popular code if one is available.

If you are still unable to operate your device,follow the instructions in the section titled CodeScan™.

Weak batteries may cause the remote to only operate one device.If this happens, simply replace them with NEW alkaline batteries and reprogram the remote.If you are sure the

batteries are good,try rolling them with your finger to ensure a good connection.

Problem

My remote control doesn’t operate my combination TV/VCR.

Solution

Most combination TV/VCRs have VCR tuners in them.You will need to select a code from the VCR section that will power up your TV/VCR. If this is the case, you probably won’t need to use a TV code.Also, to control volume with your remote control,you must program the remote for the cable box last.

Problem

What determines which device operates volume control?

Solution

Volume will be controlled through the device that was programmed last in the section titled “setting up your remote control.”For example, if the last device you programmed the remote to operate was your cable box,then the remote will control volume through your cable box and not your TV.

If none of the codes listed for your Cable Box,TV,or VCR works,the CodeScan™method will allow you to cycle through all the available codes in the remote until you find the right Cable Box,TV,or VCR code.

Manually turn ON power to the device you want to program the remote for (Cable Box,TV,or VCR).

Point the remote control at the device,and press the following keys:

[the device power button](the red buttons at the top of the remote), [SETUP], [the right arrow key],then [the device power button]

If the device is still ON,continue at step 3 below. If it turns OFF,press [SETUP] again to store the code you just selected,and you’re all done.

Press [the right arrow key],then [the device power button] until the device turns OFF.When the device turns OFF,press [SETUP] to save the code.

Please be patient — there are about 90 possible codes.

step 1

step 2

step 3

the right arrow key

If your VCR is made by one of the manufacturers listed to the right,try that code first. Otherwise, find your code in the chart below.

If your TV is made by one of the manufacturers listed to the right,try that code first. Otherwise, find your code in the chart below.

The setup code for the

GI/Jerrold™ CFT2200™ series cable box is

002

Jerrold™ is a trademark of GIC corp.

cable box code

UY322-EPG manual • version 1.1 • page 2

US Electronics UY322-EPG User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual