Us electronics UG3DIGI User Manual

Download

The chart below shows the functions of special keys for your cable box and

program guide. See the cable box manual for further details.

Part Number USE17837, version 1.0

9903

User’s Guide for the

UG3DIGI

3-in-1 Cable TV

RemoteControl

If you have a TV with a remote control, we recommend that you plug its power cord directly into a wall outlet if available (your cable installer may select an alternate setup).

Make sure to set your TV to channel 2, 3, or 4 as directed by your cable company.

Press the

[VCR] button, then the [SETUP] button on the remote.

Enter the 3-digit VCR code for your brand of VCR listed in the “VCR codes” chart on the other side of this manual by pressing the appropriate buttons on the numeric key pad.

Press the [SETUP] button again to save the code. The red indicator light at the upper left-hand corner of your remote will flash 3 times if these steps were followed correctly.

Press the

[VCR] button again to test the code you‘ve entered. The

VCR should turn on or OFF each time the

[VCR] button is pressed. If the VCR doesn’t turn on and OFF, repeat this VCR setup procedure with the next code listed in the “VCR codes” chart (section 5) .

Press the

[TV] button, then the [SETUP] button on the remote.

Enter the 3-digit TV code for your brand of TV listed in the “TV codes” chart.

Press the

[SETUP] button again to save the code. The red indicator light at the upper left-hand corner of your remote will flash 3 times if these steps were followed correctly.

Press the

[TV] button again to test the code you‘ve entered. The TV should turn on or off each time the

[TV] button is pressed. If the TV doesn’t turn on and off, repeat this TV setup procedure with the next code listed in the “TV codes” chart (section 6).

BEFORE YOU BEGIN

Weak batteries may disrupt

normal operation of the remote.

We recommend that you use

only AA alkaline batteries.

Before you can program or operate the remote control, you must install two AA Alkaline batteries.

Step 1:

Remove the battery compartment cover on the back of your remote control. A screwdriver may be required to pry the cover off.

Step 2:

Check battery polarity carefully, and install the batteries as shown in the illustration below

Step 3:

Replace the battery compartment cover.

INSTALL BATTERIES

KNOW YOUR REMOTE

SETTING UP YOUR REMOTE

FOR YOUR VCR

FOR YOUR TELEVISION

FOR YOUR CABLE BOX

b c

Press the [CABLE] button, then the [SETUP] button on the remote.

Enter the 3-digit cable box code:

[0] [0] [0].

Press the

[SETUP] button again to save the code. The red indicator light at the upper left-hand corner of your remote will flash 3 times if these steps were followed correctly.

Press the

[CABLE] button again to test the code you‘ve entered. The cable box should turn on or off each time the

[CABLE] button is pressed.

If the cable box doesn’t turn on and off, try entering the code again.

c d

IMPORTANT NOTE

US Electronics provides these function descriptions as a general guide to allow you to become more familiar with your cable box. Refer to your cable box manual for descriptions of specific functions.

Following these steps allows the remote to control volume through your cable box. If you would like volume to be controlled through your TV, perform

step C

before

step B. If you have a combination TV/VCR, use a code from the VCR Codes section (volume will be controlled only through the cable box).

www.uselectronics.com

VISIT US ON THE WEB

You can find programming instructions and codes

for all of our remote controls, as well as information

about our other products on our website:

Memory Lock

™

is an exclusive technology that saves the device codes that are programmed into the remote, even when the batteries are removed.

NUMERIC KEYS

These keys allow you to enter the channel you want to view.

You will also use them

to setup the remote

CABLE BOX

FUNCTION KEYS

See the chart below for a

description of the key

functions. Note the location

of the

[SETUP] key — you

will use it when you setup

the remote.

VCR CONTROLS

These keys operate standard

VCR or VOD functions

depending on the position of

the VCR/VOD switch. Note:

Press the [REC] key twice to

start recording on your VCR.

FAV cycles through your favorite channels

LOCK used for Parental Control

SETUP used to setup the remote

TV/VCR switches the VCR between TV and VCR mode

MUTE turns volume off MENU displays the main on-screen display menu GUIDE displays the program guide

SEL selects various options and tunes programs from the program guide

CURSOR KEYS navigate through on-screen guides

INFO displays channel and program information

EXIT exits the on-screen display menus

PAGE +/- pages through on-screen menu and program guide screens

DAY +/- moves the program guide one day forward and backward

LAST recalls the last channel that was viewed

MUSIC/ENTER switches between cable TV and Music Choice™

A, B, C future use

HELP displays help for the on-screen display

VCR/VOD switches the VCR controls into Video-on-Demand controls

NOTE

Depending on the

configuration of your

cable box, certain functions listed here may or may not be functional.

CURSOR KEYS

INFO

UG3DIGI manual • version 1.0 • page 2

US Electronics

™

, Memory Lock™, and CodeScan™are trademarks of US Electronics Components Corp.

All other trademarks are the property of their respective owners.

AOC 010 • 019 Candle 010 • 031 • 037 • 081 Capehart 035 Citizen 010 • 027 • 031 • 037

038 • 046 • 081

Concerto 037 Conklin 000 Contec 028 • 064 • 077 • 080 Craig 066 • 077 Curtis Mathes 010 • 038 CXC 077 Daewoo 019 • 027 • 040 • 041 • 046 Dixi 011 Dynatech 032 Emerson 019 • 076 • 077 • 078 • 080 • 087 Envision 010 Fisher 060 Funai 076 • 077 GE 003 • 021 • 023 • 025 • 034 • 036

Goldstar 012 • 019 • 037 Harman Kardon 044 Hitachi 029 • 037 • 050 • 054

048 • 058 • 072 • 085

Infinity 006 JBL 006 Jensen 033 JVC 009 • 065 Kloss Novabeam 022 KTV 077 Logik 018 Luxman 037 LXI 056 Magnavox 006 • 010 • 017 • 022

024 • 049 • 081 • 082

Marantz 010 MGA 007 • 010 • 019 • 061 Mitsubishi 007 • 016 • 019 • 028 • 051 • 061 Mitsubishi Monitor 016

MTC 010 • 019 • 032 • 037 • 038 NEC 010 • 019 • 037 • 070 Panasonic 002 • 006 • 034 • 036 • 067 Penney 001 • 003 • 010 • 019 • 021 • 057 Philco 006 • 010 • 019 • 020

022 • 024 • 081 • 082

Philips 006 Pioneer 008 • 071 Proscan 003 Proton 019 • 026 • 035 Quasar 034 • 036 • 083 Radio shack 027 • 068 • 077 RCA 001 • 003 • 019 • 029 Sampo 010 • 035 Samsung 010 • 019 • 027 • 037 • 038 Sanyo 052 • 055 • 060 • 086 Scott 076 Sears 017 • 055 • 056 • 057

060 • 069 • 076

Sharp 028 • 047 • 059 • 068 Sony 005 • 015 • 045 Soundesign 019 • 081 SSS 019 • 077 Sylvania 006 • 010 • 020 • 022

024 • 039 • 081 • 082

Tatung 032 Techwood 037 Teknika 007 • 018 • 019 • 027 • 031 • 037

038 • 046 • 073 • 076 • 077 • 081

TMK 037 • 019 Toshiba 060 • 056 Universal 021 • 023 Vidtech 019 Wards 006 • 010 • 018 • 019 • 020 • 021

023 • 024 • 068 • 076 • 082

Yamaha 019 Zenith 004

Manually turn ON power to the device you want to program the remote for (Cable Box, TV, or VCR).

Point the remote control at the device, and press the following keys:

[the device button] (the red buttons at the top of the remote), [SETUP], [the right arrow key],

then

[the device button]

If the device is still ON, continue at step 3 below. If it turns OFF, press [SETUP] again to store the code you just selected, and you’re all done.

Press [the right arrow key],

then

[the device button] until the device turns OFF. When the device turns OFF, press [SETUP] to save the code. Please be patient — there are about 90 possible codes.

step 1

step 2

step 3

Problem

I programmed the remote, but it won’t work my TV, VCR, or Cable Box.

Solution

You may have entered the wrong code (or the correct code might not be listed). Try entering all of the device manufacturer’s codes again, starting with the manufacturer’s popular code if one is available. If you are still unable to operate your device, follow the instructions in the section titled

CodeScan

™

Weak batteries may cause the remote to only operate one device. If this happens, simply replace them with

NEW alkaline batteries and reprogram the remote. If you are sure the batteries are good, try rolling them with your finger to ensure a good connection.

Problem

My remote control doesn’t operate my combination TV/VCR.

Solution

Most combination TV/VCRs have VCR tuners in them. You will need to select a code from the VCR section that will power up your TV/VCR. If this is the case, you probably won’t need to use a TV code. Also, to control volume with your remote control, you must program the remote for the cable box last.

Problem

What determines which device operates volume control?

Solution

Volume will be controlled through the device that was programmed last in the section titled

“setting up your remote control.” For example, if the last device you programmed the remote to operate was your cable box, then the remote will control volume through your cable box and not your TV.

TROUBLESHOOTING

CODESCAN™

TELEVISION CODES

The codes listed here are for the most popular TVs. If your TV is made by one of these manufacturers,

try the code listed here first. Otherwise, find your code in the larger chart below.

GE....................003

JVC .................009

Magnavox .....006

Mitsubishi.....007

NEC.................010

Philips............006

Pioneer ..........008

Proscan..........003

RCA.................003

Sony................005

Zenith.............004

Akai 026 • 030 • 034 • 049 Alba 016 Altec 004 Amstrad 005 ASA 008 • 022 Broksonic 061 Canon 001 Craig 028 • 064 Curtis Mathes 001 Daewoo 009 • 015 • 016 • 045 Daytron 016 Dual 026 Dynatech 005 • 029 Emerson 005 • 021 • 020 • 037

041 • 046 • 050 • 058

059 • 061 • 062

Ferguson 026 Finlux 005 • 008 Fisher 028 • 035 • 039 Funai 005 GE 001 • 007 Goldstar 022 • 023

Graetz 026 Grundig 008 Harman Kardon 023 •043 Hitachi 005 • 006 • 026 ITT 026 • 049 JCL 001 Jensen 026 JVC 013 • 026 • 040 Kenwood 026 • 027 • 040 Lloyd 005 Magnavox 001 • 008 Marantz 001 • 008 • 023 Marta 022 MEI 001 MGA 010 • 037 Minolta 006 Mitsubishi 010 • 037 • 063 MTC 005 • 064 Multitech 005 • 042 NEC 023 • 026 • 031 • 040 Normende 026 Panasonic 001 • 003

Penney 001 • 006 • 023 Pentax 006 • 038 Philco 001 Philips 008 Pioneer 036 • 040 Portland 016 Proscan 007 Quasar 001 • 047 RCA 001 • 002 • 006 • 007 Realistic 001 • 005 • 022 • 027

028 • 029 • 048 • 064

Saba 026 Saisho 046 • 059 Salora 010 Samsung 009 • 032 • 064 Sansui 026 • 040 Sanyo 027 • 028 Schaub Lorenz 026 Scott 009 • 062 Sears 006 • 022 • 027 • 028 • 035 • 039 Sharp 029 Shintom 042

Sony 014 • 017 • 018 • 019 Sylvania 001 • 010 Symphonic 005 Tatung 026 Teac 005 • 026 Teknika 001 • 005 • 022 • 033 Telefunken 026 Thomson 026 Thorn 026 TMK 021 Toshiba 009 • 010 • 026 Totevision 022 • 064 Uni-Logic 000 Unitech 064 Vector Research 023 Video Concepts 023 Videosonic 064 Wards 005 • 029 • 064 Yamaha 023 • 026 Zenith 018 • 019 • 024

VCR CODES

The codes listed here are for the most popular VCRs. If your VCR is made by one of these manufacturers,

try the code listed here first. Otherwise, find your code in the larger chart below.

GE....................001

Hitachi ...........006

JVC .................040

Magnavox .....008

Mitsubishi.....010

NEC.................023

Panasonic .....001

Proscan..........007

RCA.................007

Sony................018

Toshiba..........009

Zenith.............024

If none of the codes listed for your Cable Box, TV, or VCR works, the CodeScan

™

method will allow you to cycle through all the available codes in the remote until you find the right Cable Box, TV, or VCR code.

The Right Arrow Key

Us electronics UG3DIGI User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual