U-Reach V5.30 User Manual

DVD/Blu-ray
Duplicator

User Guide

V5.30

www.ureach-inc.com

the Expert of Duplicators

2

Content Index

9-8. Format HDD 24
9-9. Load & Copy 24

Chapter 3. Specification

Chapter 4. Appendix

Lightscribe Operation

26

Error Message

30

Chapter 1. Basic Introduction

1. Features

3

2. System Overview

4

2-1. Package Content 4
2-2. Other components necessary for
assembling the Duplicator 4
2-3. SATA controller hardware Installation
guide 5

Chapter 2. Function Operation

Function Table-CD/DVD/BD Duplicator

1. Copy

9

2. Test

10

3. Compare

10

4. Copy + Compare

11

5. Set Burn Speed

12

6. Select Source

12

7. Utility

13

7-1. Information 13
7-2. Erase Disc 14
7-3. PreScan Source 15
7-4. Track Edit 16
7-5. Eject All Disc 16
7-6. Copy Counter 16
7-7. Update BIOS 17
7-8. PRINT LS Label 17

8. Setup

18

8-1. Auto Start Time 18
8-2. Display Mode 18
8-3. Button Beep 19
8-4. Eject On Start 19
8-5. Reader Speed 19
8-6. Compare Speed 19
8-7. Language 19
8-8. Clear Setup 19

8-9. Advanced Setup 19

9. HDD Manager

(For HDD-installed duplicator)

21

9-1. Select Image 21
9-2. Disc to Image 21
9-3. Set Reader Speed 22
9-4. Show Image Info. 22
9-5. Rename Image 22
9-6. Delete Image 23
9-7. Show HDD Info. 23

3

Chapter 1. Basic Introduction

1. Features

●No PC needed. Independent SATA to SATA DVD / Blu-ray Disc Duplication.

●Sepcial Ssynchronous Load and Copy technology. When the system was installed
with HDD, the system will load master source disc to HDD while copying disc to
disc. In 2nd run copy, the system will automatically copy from HDD instead of from
the source reader.

●Support high speed 20× DVD, 52× CD, 8× Blu-ray burning.

●High compatibility with variety brands of burner.

●Easy assembly SATA port arrangement

●Support Lightscribe printing

4

Chapter 1. Basic Introduction

2. System Overview

2-1. Package Content

2-2. Other components necessary for assembling the Duplicators

HDD CD/DVD-ROM CD/DVD-RW

Writer

User Manual

SATA Cables(180˚)Controller

OK

ESC

User Manual

5

Chapter 1. Basic Introduction

2-3. SATA Controller Hardware Installation Cuide

Example: 1-7 installed

OK

ESC

HDD

ESC

OK

Write 1

Write 2

Write 3

Write 4

Write 5

Write 6

Write 7

Write 8

1.HDD (Master)

ROM (Slave)

2

3

4

5

6

7

8

1.Master

2

3

4

5

6

7

8

Slave

Example: 1-4 installed

OK

ESC

ESC

OK

Write 1

Write 2

Write 3

Write 4

Write 5

1.(ROM)

2

3

4

5

2

3

5

4

1

6

Chapter 1. Basic Introduction

OK

ESC

HDD

ESC

OK

Write 1

Write 2

Write 3

Write 4

Write 5

Write 6

Write 7

Write 8

Write 9

Write 10

Write 11

Write 12

1.HDD (Master)

ROM (Slave)

2

3

4

5

6

7

8

9

10

11

12

1.Master

2

3

4

5

8

9

10

11

12

6

7

Slave

Example: 1-11 installed

7

Chapter 2. Function Operation

Function Sub-function Description

1. Copy To copy disc to disc or copy disc from HDD.

2. Test To simulate copy process

3. Compare To bit by bit compare between source disc and copied discs

4. Copy & Compare

To copy first and compare the copied discs later. To ensure data
correctness.

5. Set Burn Speed To set burning speed for duplication.

6. Select Source To select source from any optical drive or hard disk drive.

7. Utility

1. Information

1. Disc Info.

To check the format of disc, burning speed supported and total capacity
or data size.

2. Drive Info. To check the version, model No. and brand name

3. System Info. To check the model No. and firmware version

2. Erase Disc

1. Quick Erase To quick erase data from rewritable disc.

2. Full Erase To full erase data from rewritable disc.

3. PreScan Source To check source disc’s readability.

4. Track Edit

1. Copy Track

To select and combine audio tracks from various CDs into a single
customized audio CD.

2. Close Disc

To close the disc after track copying to make the CD playable on CD
player.

3. Disc Info. To check the audio CD’s status of usage.

5. Eject All Disc To eject all trays.

6. Copy Counter

1. Show Count To check how many discs copy successfully and failed.

2. Enable Counter To enable or disable counter setting.

3. Clear Counter To delete the record.

7. Update BIOS To update the system’s firmware.

8. PRINT LS Label To print Lightscribe image.

Function Table-CD/DVD/BD Duplication

8

Chapter 2. Function Operation

8. Setup

1. Auto Start Time

Allow the system to do the Copy, Test, Compare and Copy + Compare
functions automatically

2. Display Mode

1. Basic

2. Show Timer

3. Show Speed

3. Button Beep

4. Eject On Start

1. Eject All Discs To eject all trays with disc inside once the system is booted up.

2. Do Not Eject No eject any tray or disc once the system is booted up.

3. Eject Target Only Only eject target trays with disc inside once the system is booted up.

4. Eject Source Only Only eject source disc once the system is booted up.

5. Eject All Trays To eject all trays once the system is booted up.

5. Reader Speed To adjust the reading speed of source drive.

6. Compare Speed To adjust the speed of drives while comparing.

7. Language

8. Clear Setup To reset all the function back to manufacturer’s default setting.

9. Advanced Setup

1. Power On Time To set a warm-up time from 5 seconds to 99 seconds

2. Startup Menu To select which function you would like to show up in the beginning

3. Skip Reader Error To set skip the read error and keep copying.

4. Change Bad

Master

To make the system eject source disc and ask for another one while
the source disc is unreadable for system.

5. CD Overburn Set to copy overburn CD.

6. Show HDD

Image Name

To show HDD image name or capacity on Copy, Test, Copy + Compare
and Compare function

7. Keep Buffer To set enable or disable load source to the buffer.

8. Boot Password To enable or disable the user administrative password.

9. Setup Password To set up the login password

10. Count Password To set up counter login password.

9. HDD Manager

1. Select Image To select image file from HDD as your source for copy.

2. Disc=> Image To load your source disc to the built-in HDD.

3. Set Reader Speed

To adjust the speed of source reader while you load image file from the
reader to HDD.

4. Show Image Info. To check the disc format and data size of image file

5. Rename Image To change the name of image file

6. Delete Image To delete image file in the built-in HDD

7. Show HDD Info.

To check the information of the built-in HDD includes how many discs
are stored and the free space is available

8. Format HDD To format the built-in HDD

9. Load & Copy

1. Load First To load the source to HDD and make copy at the same time.

2. Synchronous To load source to HDD first and copy from HDD to disc.

3. OFF To disable Load & Copy function.

9

Chapter 2. Function Operation

1. Copy

It is important to make sure that your source disc is placed in the right drive. You can check or
select your source reader by 6.Select Source. (plase refer to 6.Select Source, page 11)

1. Select 1.Copy and place source disc and blank discs into the proper trays. Then the system
will detect the source disc and show the information.

2. Press to start copy

3. Once the copy task is finished, the copied discs will be ejected and the result of copy task
will show on the LCD:

If HDD is selected to be the source reader, you have to upload the source to the built-in

HDD and then follow copy process to do your copy task. How to upload data from disc to
HDD please refer to 9-2.Disc to Image, page 21.

Data size

Copied data size

Speed of burning

Copy process %

Q'ty of target

**Note:
Due to default setting of auto start time, the duplicator will start to copy automatically
within a few seconds. You can set “OFF” to close the auto start function or set a longer
waiting time. The default setting is 5 seconds. (About this setting please refer to 8-1.
Auto Start Time, page 17 )

Elapsed time

Data size

Q'ty of target disc

**Note:
The default setting of source reader is the first drive.

10

Chapter 2. Function Operation

2. Test

This function will simulate the copy process to ensure error free duplication. During the
simulation, it will be nothing left in the recordable discs.

1. Using / to select 2.Test and press .

2. Press to start test

3. Once the test task is finished, the discs will be ejected and the result of the pass and fail
discs for the test task will show on the LCD:

3. Compare

This function will do bit-by-bit comparison between source disc and copied discs to ensure the
copied discs are identical to source disc.

1. Place source disc and blank discs into Reader and Writer separately.

2. Using / to select 3.Compare and press to start compare.

**Note:

1

This function is unable to support DVD+R blank disc.

2

If you use CD/DVD rewritable discs as your blank media in the simulation, all the
content inside the discs will be erased permanently during test simulation.

11

Chapter 2. Function Operation

3. The system will detect the source and target discs automatically.

4. After detecting, the system will start to compare.

5. When the comparison has finished, the system will show the compare result.

4. Copy + Compare

This function will to do copy task first and execute comparison automatically when copy process
has been finished.

**Note:
In Copy, Test, Compare and Copy+Compare functions

1

If there is no source and target discs inside the duplicator, there will be nothing

show on LCD.

2

If the built-in HDD is selected as source, the information presents different:

3

The information display of these 4 functions will be different based on the

display mode you selected.

(Plase refer to 8-2.Display mode, page 17)

Image file name

12

Chapter 2. Function Operation

5. Set Burn Speed

You can adjust the burning speed of CD/Audio CD/DVD/DVD DL/Blu-ray by this setting. The
default setting of CD is 40X, Audio CD 24X, DVD 8X, DVD DL 2X and Blu-ray 2X.

1. Using / to select 5.Set Burn Speed and press .

2. Pressing / to adjust the burning speed of CD and press to confirm it, or press

to select Audio CD,DVD, DVD DL or Blu-ray to adjust the burning speed.

6. Select Source

You can set any drive or built-in HDD in the duplicator to be your source reader.

1. Using / to select 6.Select Source

2. Press to check the current source reader, or select the proper drive to be the source
reader by pressing / , once the source reader is selected, press to confirm the

setting and back to the menu list.

**Note:
The default setting of source reader is the first drive.

13

Chapter 2. Function Operation

7. Utility

7-1. Information

You can check the information of disc, drive and system by this function. By pressing / ,
each disc or drive’s information will show on the LCD.

1. Using / to select 7.Utility, press to enter the sub menu. Then, select

1.Information and press .

2. Using / to select 1.Disc Info. or 2.Drive Info or 3.System Info., and press to see
the related information.

3. The information will show on the LCD as below:

●Disc Info.: You can check the format of disc, burning speed supported and total
capacity. If the disc has data inside, you also can check the size of data.

●Drive Info.:

1. HDD:you can press the button ,to check your HDD Brand&Model name.

2. Drive:The version,model No.and brand name can be checked here.

Burning Speed

Capacity/Data size

Disc Format

Drive version

Brand name

14

Chapter 2. Function Operation

OR

●System Info.: The model No. and firmware version can be checked here.

7-2. Erase Disc

This function will erase the rewritable discs in WRITER tray, there are two erase modes available:

●Quick Erase: It will erase the INDEX of the rewritable disc.

●Full Erase: It will erase ALL DATA in the rewritable disc, which takes longer time than Quick
Erase.

1. Place discs into writers.

2. Using / to select 7.Utility and press to enter the sub menu. Then, select 2.Erase
and press .

3. Using / to select 1.Quick Erase. or 2.Full Erase.

4. Pressing to execute the erasing task. When the system is detecting the discs, you will
see the colon flashing.

5. When the erase job is in process, you should see the O and o are blinking by turns.

The Second Drive

15

Chapter 2. Function Operation

6. Once the erase task has finished, the O stop blinking, the disc will be ejected automatically.

7-3. PreScan Source

This function will scan and detect any bad sectors existing in the source disc, which helps you
to ensure the readability of source disc.

1. Place a source disc into reader.

2. Using / to select 7.Utility and press to enter the sub menu. Then, select

3.Prescan Source and press to start scan task.

3. When prescan task is in process, you can see the process on the display:

4. When the prescan task has finished, the result of prescan will be shown on the LCD.

**Note:

1

If you see F and f are blinking by turns, which means the whole new DVD+RW is in

format process.

2

Erase function only support rewritable discs.

Data size

Scanned data size

Elapsed time

Scan process %

16

Chapter 2. Function Operation

7-4. Track Edit

This function enables you to combine audio tracks from various CDs into a single customize
audio CD.

●Copy Track: You can select and combine audio tracks from different CDs in this section.

●Close Disc: You have to perform this function after copy track to make the CD playable on
CD player.

●Disc Info.: You can check the audio CD’s status of usage.

7-5. Eject All Disc

You can eject all discs including source and target discs at the same time by this function.

7-6. Copy Counter

This function will record the result of duplication.

●Show Count: You can check how many discs copy successful and failed.

●Enable Counter: You can set the counter enable or disable to record the copy result.

●Clear Counter: You can delete the record by this function.

1. Using / to select 7.Utility and press to enter the sub menu. Then, select 6.Copy
Counter and press .

2. Using / to select 1.Show Count.

3. Pressing to check the calculation of successful and failed duplication for CD and DVD

Q'ty of passed CD

Q'ty of failed CD

17

Chapter 2. Function Operation

7-7. Update BIOS

You can update the system’s firmware in this function.

1. Place manufacturer certified update file CD into any drive

2. Pressing / to select 7.Utility and sub menu 7.Update BIOS and then press to
start the process.

3. The system will detect the update file and execute update task automatically.

4. Once the update job has done, the system will require you to reboot the system.

7-8. PRINT LS Label

This function will let you using the Lightscribe technology to print your own image on discs.
The operation process please refer to Appendix Lightscribe Operation.

**Note:
Do NOT save the firmware in a folder. The system can not detect the file if you save it in
a folder.

18

Chapter 2. Function Operation

8. Setup

8-1. Auto Start Time

This setting will allow the system to do the Copy, Test, Compare and Copy + Compare functions
automatically in a few seconds once the source and blank discs are placed in the trays and
detected by the system. The default setting is 5 seconds. You can set a longer/shorter time from
1 to 99 seconds or set OFF to disable this function and execute copy task by manual.

1. Pressing / to select 8.Setup and sub menu 1.Auto Start Time.

2. Pressing / to set the time.

8-2. Display Mode

You can select the prefered display mode in Copy, Test, Compare, Copy+Compare.

●Basic: It will only show the copy process (%) on LCD.

●Show Timer: It will show the time for copy.

●Show Speed: It will show the speed of burning during copy process.

Speed of burning

Elapsed time

Data size

Q'ty of target

Copied sizeCopy process %

19

Chapter 2. Function Operation

8-3. Button Beep

This setting will allow you to set up to hear a beep when a button is pressed or not.

8-4. Eject On Start

You can make the trays or discs eject once the system is booted up.

●Eject All Discs: To eject all trays with disc inside once the system is booted up.

●Do Not Eject: No eject any tray or disc once the system is booted up.

●Eject Target Only: Only eject target trays with disc inside once the system is booted up.

●Eject Source Only: Only eject source disc once the system is booted up.

●Eject All Trays: To eject all trays once the system is booted up.

8-5. Reader Speed

This setting allows you to adjust the reading speed of source drive. The default setting of reader
speed of CD is 40X; DVD is 24X.

8-6. Compare Speed

The reading speed of drive and disc are the reasons can affect the quality of comparison. This
setting allows you to adjust the reading speed of drives to match up the reading speed of discs.
The default setting of CD’s compare speed is 40X, DVD is 8X.

8-7. Language

You can set a proper language for interface during operation.

8-8. Clear Setup

This setting will reset all the function back to manufacturer’s default setting.

8-9. Advanced Setup

●Power On Time: You can set a warm-up time from 5 to 99 seconds for warming up the
duplicator when it is turned on. The default setting is 10 seconds.

●Start-up Menu: You can select which function you would like to show up in the beginning.

●Skip Read Error: You can set this function enable to skip disc errors in order to avoid bad
quality of copy. If you are confident of your source disc has only a small and insignificant
error due to physical damages and can be overlooked, you can set NO to disable this
function.

20

Chapter 2. Function Operation

●Change Bad Master: This setting will make the system eject source disc and ask for another
one while the source disc is unreadable for system.

●CD Overburn: The majority of discs have a small margin of extra groove at the outer edge.
This setting allows you to copy data over the normal size limit.

●Show HDD Image Name: You can select to show HDD image name or capacity on Copy,
Test, Copy + Compare and Compare function.

●Keep Buffer: You can set Yes to load source disc to buffer in first round of Copy, Test,
Compare or Copy+Compare, and do it again without the source disc. Or you can set No to
keep buffer not be used.

●Boot Password: This setting allows you to enable or disable the user administrative
password. Users have to login when the system is booted on.

●Setup Password: You can set up password by pressing / to select the number you
like and press to set next number.

●Count Password: You can select the disable/Enable mode and Count your login password.

**Note:
Skip Read Error can not fix the error in the source disc, all it does is skipping the errors
and keeps copying the rest of readable data.

Show HDD Image Name: Show capacity:

**Note:
The source will be only temporary saved in buffer, there will be nothing left when you exit
the task (Copy, Test, Compare and Copy+Compare or reboot the system.

**Note:
When you change the source from drive to HDD, the LCD will show the HDD information.
How to change your source reader please refer to 6.Select Source, page 11.

21

Chapter 2. Function Operation

9. HDD Manager

(For HDD-installed duplicator)

9-1. Select Image

You can select image file from HDD as your source for copy. When this function is selected, the
system will set the HDD to be the source reader automatically.

1. Pressing / to select 9.HDD Manager and sub menu 1.Select Image.

2. Pressing / to select the image you need and press to confirm.

9-2. Disc to Image

This function will load your source disc to the built-in HDD and save the source as an image file.

1. Placing the source disc to any one of the drives

2. Pressing / to select 9.HDD Manager and sub menu 2.Disc to Image.

3. Pressing to start loading.

Data size

22

Chapter 2. Function Operation

4. When loading has finished, the disc will be ejected automatically.

9-3. Set Reader Speed

You can adjust the reading speed of the drive which you put the source disc. This function is
ONLY available when you loading the source disc to HDD. The default setting of both CD and
DVD speed are MAX.

9-4. Show Image Info.

You can check the disc format and data size of image file in this function.

1. Pressing / to select 9.HDD Manager and sub menu 4.Show Image Info.

2. Press to check the disc format and data size of the image file. And you can press /
to check other image file’s information.

9-5. Rename Image

This function allows you to change the name of image file. You can set maximum up to 8
characters for a new name, and NO blank is allowed between the characters.

**Note:
The source disc can be placed in any drive, it will not affect the loading process.

23

Chapter 2. Function Operation

1. Pressing / to select 9.HDD Manager and sub menu 5.Rename Image.

2. Pressing and select which image file you would like to rename by pressing / ,

and then press to start edit a new name for the selected file.

You can select characters or number by pressing / , and press to the next space

to edit. The maximum is 8 characters without blank space. When it has done, press to
confirm the new name.

9-6. Delete Image

You can delete image file from the built-in HDD, but the source image file is unable to delete
if the file is selected as source. Therefore, before you delete an image file, please check if it is
selected as a source and change a new one source by 9.1Select Image, page 20.

9-7. Show HDD Info.

You can check the information of the built-in HDD includes how many discs are stored and the
free space is available in the HDD.

**Note:
If there is an image file is deleted, the file name will be held for next new image file, the
existing file will not to fill the vacancy. For example, there are 5 image files (A001~A005)
in the HDD, when you delete A003, A004 will not change to be A003, once a new file
has loaded, its default name will be A003.

24

Chapter 2. Function Operation

9-8. Format HDD

This function allows you to format the built-in HDD while the HDD is NOT selected as reading
source. You can change the source from HDD to other drive in 6.Select Source, page 11.

Due to the capacity for discs loading is hard to predict precisely and more and more different
discs coming out. The traditional method of format is not ideal for using on this duplicator.
This duplicator is able to detect disc capacity and assign a proper partition for the disc’s data
automatically. You do not have to predict and select CD or DVD partition in the beginning and you
can check how many discs you can upload from 9-7.Show HDD Info., page 23 This intelligent
HDD management technology is much easier for HDD management than the old way.

9-9. Load & Copy

This function is for the system to load the source to HDD and make copy synchronously. The
system will load the source to HDD during the first round of duplication, and the HDD will replace
the reader drive to be the source in second round of duplication. This special function is very
convenient for a big copy task. You also can set:

●Load First: The system will load source to HDD first and take HDD as source to copy.

●Synchronous: The system will load the source to HDD and make copy at the same time.

●OFF: To disable Load & Copy function.

**Note:

1

The image file will only be saved temporary if it is loaded to HDD by Load & Copy

function.

2

If you would like to save the file permanently please load the file to HDD by manual

(refer to 9-2.Disc to image, page 21)

25

Chapter 3. Specication

Model P501D P504D P507U/W P511U/W P515X

Target 1 4 7 11 15

Buffer (DDR2) 64MB 128MB(U) / 512MB(W) 256MB

Interface SATA

CD Speed 52X

DVD Speed 20X

Blu-ray Speed 8X

Writing Method DAO, TAO, RAW

Disc Format Support

BD-ROM, BD-R, BD-RE

DVD-ROM, DVD-Video, DVD-Audio, DVD+R, DVD+RW, DVD-R, DVD-RW, Dual

Layer DVD±R,

CD-ROM, CD-RW, CD-I, Audio CD, Video CD, CD+G, CD-TEXT,

Bootable CD, Mixed-mode CD, Multi-session CD, CD-Extra,

Business Card CD, 3” Mini CD-R

Display 2x16 Backlight Monochrome LCD

Input 4 push buttons ( Forward, Backward, OK, Esc)

Language Support English, Japanese, Chinese, Portuguese, Spanish

Temperature

Working 5°C ~ 45°C

Storage -20°C ~ 85°C

Humidity

Working 20% ~ 80%

Storage 5% ~ 95%

Controller Power

Consumption

Voltage 5V±5%

Current 3A Max

Safety FCC, CE, RoHS

Controller Weight (NW / GW) (g) 190 / 370 210 / 480 250 / 580 260 / 680 300 / 850

＊

The above information is for marketing reference only. The actual specification may subject to change without notice.

Chapter 4. Appendix

26

Lightscribe Operation

Step 1

Install Lightscribe template software to PC

Download LightScribe software from www.lightscribe.com and install below software.
A. LIGHTSCRIBE SYSTEM SOFTWARE (LSS)

B. LIGHTSCRIBE TEMPLATE LABELER.

A

B

Chapter 4. Appendix

27

Step

2

Execute "LightScribe Drive select.exe".exe file to select LightScribe Drives

1. Receive a .exe file from your supplier.

2. Execute the .exe file on your PC.

3. And select the LightScribe Duplicator drive on the list.

4. If the duplicator’s Lightscribe drive is not on the list, please follow below steps to add new

lightscribe drive to the support list.

❶

Plug the new lightscribe drive you will use for Duplicator to the PC.

❷

Click "Detect Lightscribe Drive And Disc " to search new available lightscribe drive.

❸

Select the new drive and press , the drive will be added to the list.

**Note:
When everytime the Duplicator change LightScribe drive, must re-select drive
before create LightScribe image for that Duplicator.

Chapter 4. Appendix

28

Step 3

Design Lightscribe Template and Lightscribe printing on PC.

1. Click to launch the LightScribe Template on our PC.

2. Follow procedure to create your label image.

3. Make sure the lightscribe drive is selected.

4. Click the Print to save the lightscrbe image .LSI file to a USB stick or a Disc.

**Note:
If Lightscribe template can not be executed normally under Window7, please try
to click right button on the mouse on the Lightscribe icon and select " Run as
administrator" to execute the function.

❹

❸

Chapter 4. Appendix

29

5. Plug the USB drive or Disc into Duplicator.

6. Select the utility function 7-8.PRINT LS Label. The system will read the image into the

duplicator and start printing the lightscribe label.

Print side

Data side

**Note:
When doing the lightscribe printing, please turn over the disc. The print side is face
down and data side is face up.

Chapter 4. Appendix

30

Error Message

Error Message Possible Reasons Toubleshooting

Bad Master Disc

Master disc is empty or protected.

Please check your master disc by (1) Disc Info (2) by PC.

Master disc has demaged or bad quality

Warning:
Can’t DVD↑CD

You put different format of blank disc from the master disc.
Can not copy between different disc format

Please check your master and blank disc foramt by " Disc
info". Only can copy CD to CD, DVD to DVD.

Not Blank Disc

The target disc has been written. Please use blank disc or rewrittable disc.

No Disc

No blank disc. Or the disc is upsite down.

Please double check again your target disc.

Using Blu-Ray blank disc, but the driver does not support Blu­Ray.

No Master Disc

No source disc Please check if you put the right source disc into the drive.

Use Blu-Ray as a source, but the driver does not support Blu­Ray.

Please check the disc format by "Disc Info".

Read Error Count
Over Limit

(happen when you load data from disc to

HDD)

Master disc has bad quantity. Please change another source.

Master disc is a protected disc Please don't use protected disc as a source.

No update file

No disc with updated FW, can't find FW files

1. Check if you unzip the FW file.

2. Check if the FW is placed at root level.

3. Check if you put the right disc with FW.

4. Try the FW disc with other drives.

HDD Full !

HDD has no enough space Please relase HDD space.

Wrong Password

Insert wrong password Please double check again your password.