Installation Manual
MFS-8
Network Switch
MFS-8 Installation Manual ©2010-2013 Universal Remote Control,
Inc.
The information in this owner’s manual is copyright protected. No part of this
manual may be copied or reproduced in any form without prior written consent
from Universal Remote Control, Inc.
UNIVERSAL REMOTE CONTROL, INC. SHALL NOT BE LIABLE FOR OPERATIONAL, TECHNICAL OR EDITORIAL ERRORS/OMISSIONS MADE IN
THIS MANUAL.
The information in this owner’s manual may be subject to change without prior
notice.
URC - Control the Experience is a registered trademark of Universal Remote
Control, Inc.
Total Control is a registered trademark of Universal Remote Control, Inc.
All other brand or product names are trademarks or registered trademarks
of their respective companies or organizations.
500 Mamaroneck Avenue, Harrison, NY 10528
Phone: (914) 835-4484 Fax: (914) 835-4532
TABLE OF CONTENTS
Introduction 1
Features and Benefits 1
Parts Guide 1
Front Panel Descriptions 2
Rear Panel Descriptions 3
MFS-8 Installation Considerations 4
MFS-8 Installed in a Small System 5
MFS-8 Installed in a Large System 6
MFS-8 Installed in the area with
the Network Distribution 7
Frequently Asked Questions 8
Specifications 8
Limited Warranty Statement 9
End User Agreement 11
Federal Communication Commission
Interference Statement 12
Regulatory Information to the user 13
Declaration of Conformity 14
Page 1
Introduction
The MFS-8 Network switch is the ideal "Plug-n-Play" solution to protect network WAPs (Wireless Access Points) from multicast audio
streams.
Total Control products, like the DMS-1200 (Multi-zone Amplifier),
DMS-100 (Single-Zone Amplifier) and the SNP-1 (Streaming Network
Player), all multicast audio streams onto the LAN. The nature of a
"multicast" will shut down all wireless access to the network. The
MFS-8 was specifically designed for use with Total Control Systems
and incorporates pre-configured MAC filtering. MAC Filtering com-
pletely solves the issue by confining multicast streams to the switch
itself, never allowing streams to affect network traffic in the rest of the
house. Pre-configuration means you don't have to be a Network
Engineer to configure this switch, simply plug your Total Control products into any port and you're ready to go. "Plug-n-Play" integration
produces reliable, predictable network performance.
Warning: NEVER plug a WAP (Wireless Access Point) into the MFS8, since URC multicast audio streams will shut down any brand or
model of WAP.
Features
Eight (8) ports plus one LAN port.
Mac filtering prevents audio streams from consuming network
bandwidth.
Activity and Status LEDs plus Connectivity indicator.
Includes 12 volt power supply.
Parts Guide
1 - MFS-8 MAC Filtering Switch
1 - 1.5M CAT5 Ethernet Cable
1 - 12V AC Power Adapter
1 - Wall Mount Plate and Four Mounting Screws
1 - Quick Install Guide
w
w
w
w
MFS-8 NETWORK SWITCH INSTALLATION MANUAL
MFS-8 NETWORK SWITCH INSTALLATION MANUAL
Front Panel Descriptions
Power Indicator: Illuminates when the MFS-8 Power Supply is con-
nected to AC outlet.
Ethernet Network Connectivity Indicator: Illuminates when the
MFS-8 is connected to a LAN and has received an IP Address.
Power
Indicator
LAN Connectivity
Indicator
Page 2
Page 3
Rear Panel Descriptions
Power: Provides connection to included 12V Power Supply.
LAN Connection: Provides connection to the LAN (Local Area
Network).
10/100 Ports: 8 - 10/100 Ports provide network connectivity to Total
Control streaming products like the DMS-1200, DMS-100 and SNP-1.
MAC Filtering: MAC Filtering prevents audio and video streams
from consuming network bandwidth. Streams are confined to the
switch, optimizing local area network performance.
Network Connectivity and Activity Status Indicators (port specific):
Status indicator LEDs display network connectivity, and network
traffic feedback, for easy troubleshooting.
Wall Mount Bracket: Convenient removable wall bracket allows the
MFS-8 to be mounted to the back of a cabinet or rack. Remove the
wall bracket when placing the MFS-8 on a shelf or stand.
MFS-8 NETWORK SWITCH INSTALLATION MANUAL
Power LAN connection 8-10/100 Ports Mac Filtering
Soft Rubber
Non-Scuff Feet
Removable Wall Bracket
Network Status
Indicator LEDs
Page 4
MFS-8 NETWORK SWITCH INSTALLATION MANUAL
MFS-8 Installation Considerations
Only one MAC Filtering switch should be used in a typical Total
Control system. All streaming products like the DMS-1200, DMS100 and SNP-1 must be connected to the switch.
You cannot daisy-chain MFS-8 MAC Filtering switches; communication between switches will be blocked. If you have more than eight
of the above streaming components, simply connect a standard network switch to any port on the MFS-8 and then connect the additional components to the standard switch. This allows the additional
components to benefit from the MFS-8's MAC Filtering, without
affecting communication between devices.
Warning: NEVER plug a WAP (Wireless Access Point) into the MFS-8,
it will not function correctly.
Installation
1. On the back of the MFS-8, connect one end of a CAT5 cable to
the port labeled LAN 10/100.
2. Connect the other end of the CAT5 cable to the LAN (Local Area Network).
3. Connect Total Control and standard network devices to any of
the eight 10/100 Smart Ports.
4. Connect the supplied 12V Power Supply to the MFS-8 and then
plug it into an unswitched AC outlet.
5. Once powered up, the unit begins working in approximately 30
seconds.
X
OK
Do Not Daisy-Chain MFS-8s
Cable Modem
Internet
Wi-Fi Router
MFS-8
MFS-8
MFS-8
Standard Network Switch
Page 5
MFS-8 Installed in a Small System
Notes:
n The Wireless Access Point CANNOT be connected to the MFS-8;
it must be connected to the Router in the LAN.
MFS-8 NETWORK SWITCH INSTALLATION MANUAL
Cable Modem
Internet
Wi-Fi Router
MFS-8
Wireless
Access
Poin t
PSX-2
MRX-10
SNP-1
DMS-1200
Standard PoE Switch
TKP-100TKP-2000 TKP-2000 TKP-100 MC 75 CD IP
Camera 1
MC 75 CD IP
Camera 2
Page 6
MFS-8 NETWORK SWITCH INSTALLATION MANUAL
MFS-8 Installed in a Large System
Notes:
n The Wireless Access Point CANNOT be connected to the
MFS-8; it must be connected to the Router in the LAN (Local
Area Network).
n A standard network switch is used to connect the MFS-8 to the LAN.
n An MRX-10 doesn't have to be connected to the MFS-8, but
can be connected to a standard network switch when
convenient to do so.
Cable Modem
Internet
Wi-Fi Router
Standard Network Switch
wireless
Access
Point
MFS-8
PSX-2
MRX-10
SNP-1
DMS-100
DMS-1200
Standard PoE Switch
TKP-2000
TKP-2000 TKP-100 TKP-100
MC 75 CD IP
Camera 1
MC 75 CD IP
Camera 2
Page 7
MFS-8 NETWORK SWITCH INSTALLATION MANUAL
MFS-8 Installed in the area with the Network
Distribution
Occasionally you get a retrofit installation where only one CAT5
wire has been run to a room, and there's no way to run another
one. In this case, locate the MFS-8 in the Utility Room, Garage, or
where ever the central distribution point for the Network is located,
and install standard network switches in rooms where you plan to
locate a DMS-1200, DMS-100 or SNP-1.
Notes:
n The Wireless Access Point CANNOT be connected to the
MFS-8; it must be connected to the Router in the LAN.
n Standard network switches are used to connect the DMS-
1200, DMS-100 and SNP-1 to the MFS-8. This configuration
provides MAC Filtering to the Total Control streaming components, while freeing up additional ports on the MFS-8 to connect devices like DMS-1200, DMS-100 and SNP-1.
n An MRX-10 doesn't have to be connected to the MFS-8, but can
be connected to a standard network switch when convenient
to do so.
Contral Distribution Point
for Network Wiring
Standard Network Switch
(Network for the rest of the House)
MFS-8
MRX-10
Standard Network Switch
DMS-100
SNP-1
DMS-1200
Attic Office
Family Room
Cable Modem
Internet
Wi-Fi Router
wireless
Access
Point
Page 8
MFS-8 NETWORK SWITCH INSTALLATION MANUAL
Frequently Asked Questions
1. Do I need to use a MFS-8 in a Total Control system?
If you are only controlling a Home Theater with a MRX-10, and
there are no Total Control streaming sources like the DMS-1200 or
DMS-100 in the system, then the answer is NO, you do not need
to use a MFS-8. If you have DMS-1200(s) or DMS-100(s) in the
system, then the answer is YES, you must use a MFS-8 in the
system, connected to those components.
2. Can I connect both PoE (Power over Ethernet) devices like KP4000 keypads and Non-PoE devices to the MFS-8?
No, you cannot use an MFS-8 to power Keypads or Cameras -- it is
not PoE.
3. What if I have more than eight streaming devices?
You can connect a standard network switch to the MFS-8 to expand
the MAC Filtering capabilities of the MFS-8.
4. Can I connect a WAP (Wireless Access Point) to the MFS-8?
No, the WAP will not function properly when multiple streams are
occurring in the system. Connect the WAP to a standard PoE network switch, outside of the MFS-8. Never connect a WAP to the
MFS-8.
5. I have one CAT5 cable going to a room where my client has a
network printer and a PC and I need to install a DMS-100 Single
Zone Amplifier, via the same CAT5 cable, in the room. How do I
connect everything?
In the room where you plan to install the DMS-100, connect a standard network switch to the incoming CAT5, and then connect the
DMS-100, PC and Printer to the switch. It is not recommended to
connect PCs used for internet gaming to a MFS-8, as this may
affect the performance of video gaming during heavy stream usage.
Specifications
Microprocessor: 55MHz RISC
Memory: 4 Megabits of Serial Flash, 512KB Flash, 128KB SRAM
Network: Switching - Eight 10/100 Ethernet ports, LAN - One
10/100 Ethernet port
Power Supply: 12V External Power Supply
Size: 1.5” x 9.8” x 4.9” (H X W x D)
Weight: 0.78 lbs. (0.35kg)
Page 9
Limited Warranty Statement
1. Limited Warranty and Disclaimers
Universal Remote Control, Inc. (“URC”) warrants that the URC equipment
shall be free from defects in material and workmanship under normal usage
for one (1) year from purchase when such is purchased from URC. This
limited warranty is valid only in the United States of America. URC warrants
that the software will substantially conform in any material respect to its
functional specifications at the time of delivery. URC SHALL NOT BE LIABLE
FOR OPERATIONAL, TECHNICAL OR EDITORIAL ERRORS AND/OR
OMISSIONS MADE IN THE URC DOCUMENTATION. URC DOES NOT
WARRANT THAT THE URC SOFTWARE IS BUG-FREE OR ERROR FREE
OR THAT THERE ARE NO ERRORS/BUGS IN THE URC SOFTWARE.
URC warrants that at the time of purchase the URC equipment and the URC
software complied with all applicable regulations and policies of the Federal
Communications Commissions (“FCC”) regarding electromagnetic
interference caused by electronic/computing devices and to the extent that the
URC equipment and/or the URC software fails to so comply, URC shall, at its
own expense, take all reasonable measures to promptly cause such to
comply.
URC equipment purchases from other than an authorized URC dealer or
distributor are without warranty.
THIS LIMITED WARRANT DOES NOT COVER TECHNICAL ASSISTANCE
FOR HARDWARE OR SOFTWARE USAGE EXCEPT AS EXPRESSLY
PROVIDED FOR HEREIN, THE EQUIPMENT, SOFTWARE AND
DOCUMENTATION OF URC ARE SUPPLIED “AS IS” WITHOUT ANY
WARRANTY, EXPRESS, STATUTORY OR IMPLIED, OF ANY KIND. TO
THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, URC
EXPRESSLY DISCLAIMS ALL WARRANTIES, EXPRESS, STATUTORY OR
IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. URC
DOES NOT WARRANT, GUARANTEE, OR MAKE ANY
REPRESENTATIONS REGARDING THE USE OF, OR THE RESULTS OF THE
USE OF, THE EQUIPMENT, SOFTWARE OR DOCUMENTATION IN
TERMS OF CORRECTNESS, ACCURACY, RELIABILITY OR OTHERWISE.
EXCEPT AS EXPRESSLY PROVIDED FOR HEREIN, TECHNICAL SERVICES
ARE SUPPLIED “AS IS”, WITHOUT ANY WARRANTY, EXPRESS,
STATUTORY OR IMPLIED, OF ANY KIND. TO THE MAXIMUM EXTENT
PERMITTED BY APPLICABLE LAW, URC EXPRESSLY DISCLAIMS ALL
WARRANTIES, EXPRESS, STATUTORY OR IMPLIED, INCLUDING BUT
NOT LIMITED TO THE WARRANTIES OF QUALITY OR REASONABLE
SKILL AND CARE, OR OUTCOME OR RESULTS.
MFS-8 NETWORK SWITCH INSTALLATION MANUAL
Page 10
WITHOUT IN ANY WAY LIMITING THE GENERALITY OF THE OTHER
PROVISIONS HEREIN, WARRANTY DOES NOT COVER: (I) DAMAGE
FROM MISUSE, NEGLECT OR ACTS OR NATURE, (II) MODIFICATIONS,
(III) INTEGRATION WITH THIRD PARTY CONTENT (IV) BEYOND THE
WARRANTY PERIOD AND/ OR FAILURE TO FOLLOW URC WARRANTY
CLAIM PROCEDURE.
The warranty limitations and warranty disclaimers may not apply to end user
in whole or in part, where such are restricted or excluded by applicable law
and such shall apply to the maximum extent permitted by applicable law.
In the event of any warranty claim, URC will, at its sole option, repair the URC
equipment using new or comparable rebuilt parts, or exchange the URC
equipment for new or rebuilt equipment. In the event of a defect, these are
the end user’s exclusive remedies.
All the URC equipment returned for service, exchange or repair require an
RGA number. To obtain an RGA number, you must complete a Return
Request Form which you may obtain by calling (914) 835-4484 or contacting
URC at returnrequest@universalremote.com. To obtain warranty service, end
user must deliver the URC equipment, freight prepaid, in its original packaging
or packaging affording adequate protection to URC at 420 Columbus Avenue,
Valhalla, NY 10595. It is end user’s responsibility to backup any macro
programming, artwork, software or other materials that may have been
programmed into the unit. It is likely that such data, software, or other
materials will be lost during service and URC will not be responsible for any
such damage or loss. A dated purchase receipt, bill of sale, installation contract
or other verifiable proof of purchase is required. For the URC equipment
support and other important information, please visit URC's website available
at www.universalremote.com or call the Customer Service Center at (914)
835-4484.
This limited warranty only covers the URC equipment issues caused by
defects in material or workmanship during ordinary consumer use. It does not
cover product issues caused by any other reason, including but not limited to
product issues due to commercial use, acts of God, third-party installation,
misuse, limitations of technology, or modification of or to any part of the URC
equipment. This limited warranty does not cover the URC equipment sold as
used, as is, refurbished, so called "B stock" or consumables (such as batteries).
This limited warranty is invalid if the factory applied serial number has been
altered or removed from the URC equipment. This limited warranty
specifically excludes the URC equipment sold by unauthorized resellers.
With the exception of URC’s IR-only, broad-based consumer remotes, none of
URC’s PC programmable remotes or any of our Total Control® whole-house
MFS-8 NETWORK SWITCH INSTALLATION MANUAL
MFS-8 NETWORK SWITCH INSTALLATION MANUAL
equipment are authorized for online internet sales. Buying URC’s PC
programmable remotes or any of our Total Control® whole-house equipment
online means buying equipment that does not have a URC’s limited warranty.
Such equipment is not eligible for URC tech support or software support,
either.
2. URC’S Limitations of Liability
IN NO EVENT SHALL URC BE LIABLE FOR INDIRECT, SPECIAL,
INCIDENTAL, EXEMPLARY, PUNITIVE OR CONSEQUENTIAL DAMAGES
OF ANY KIND OR LOSS OF PROFITS OR BUSINESS OPPORTUNITY,
EVEN IF URC IS ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
IN NO EVENT SHALL URC BE LIABLE FOR LOSS OF OR DAMAGE TO
DATA, COMPUTER SYSTEMS OR COMPUTER PROGRAMS.
URC’S LIABILITY, IF ANY, FOR DIRECT DAMAGES OF ANY FORM SHALL
BE LIMITED TO ACTUAL DAMAGES, NOT IN EXCESS OF AMOUNTS
PAID BY END USER FOR THE URC EQUIPMENT.
IN NO EVENT SHALL URC BE LIABLE FOR ANY EVENTS BEYOND ITS
CONTROL, INCLUDING ANY INSTANCE OF FORCE MAJEURE.
IN NO EVENT SHALL URC BE LIABLE FOR THE ACTS OR OMISSIONS OF
END USER OR ANY THIRD PARTY.
THE LIMITATIONS OF LIABILITY MAY NOT APPLY TO END USER IN
WHOLE OR IN PART, WHERE SUCH ARE RESTRICTED LIMITED OR
EXCLUDED BY APPLICABLE LAW AND SUCH SHALL APPLY TO THE
MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW.
URC SHALL NOT BE HELD RESPONSIBLE FOR THE STATEMENTS MADE
BY OTHERS.
SOME STATES OR JURISDICTIONS DO NOT ALLOW THE EXCLUSION
OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR
ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS,
SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO
END USER. THIS LIMITED WARRANTY GIVES END USER SPECIFIC LEGAL
RIGHTS AND END USER MAY HAVE OTHER RIGHTS WHICH VARY
FROM STATE TO STATE OR JURISDICTION TO JURISDICTION.
End User Agreement
The terms and conditions of the End User Agreement available at
www.universalremote.com/eua.php shall apply.
Page 11
Page 12
Federal Communication Commission
Interference Statement
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one more of the
following measures:
u Reorient or relocate the receiving antenna.
u Increase the separation between the equipment and receiver.
u Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
u Consult the dealer or an experienced radio/TV technician for
help.
Warning!
Changes or modifications not expressly approved by the manufacturer could
void the user's authority to operate the equipment.
Note : The manufacturer is not responsible for any Radio or TV interference
caused by unauthorized modifications to this equipment. Such modifications
could void the user's authority to operate the equipment.
FCC Caution
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the authority to operate equipment.
MFS-8 NETWORK SWITCH INSTALLATION MANUAL
Page 13
MFS-8 NETWORK SWITCH INSTALLATION MANUAL
Regulatory Information to the user
n CE conformity Notice
Products with “CE” marking comply EMC Directive 2004/108/EC issued
by the commission of the European Community.
1) EMC Directive
lEmission : EN 55022
lImmunity : EN 55024
lPower : EN-61000-3-2, 3
n Declaration of Conformity
“Hereby, Universal Remote Control Inc. declares that this MFS-8 is in
compliance with the Essential requirements and other relevant provisions
of EMC Directive 2004/108/EC.”
Certification
Type No.(Model No.) MFS-8
Batch/Serial No. Power Rating 12.0V , 1.0A
Page 14
MFS-8 NETWORK SWITCH INSTALLATION MANUAL
Declaration of Conformity
Company Name : Universal Remote Control Inc.
Company Address : 500Mamaroneck Avenue, Harrison, NY 10528, U.S.A
Contact Information :
www.universalremote.com
Phone: (914)835-4484 Fax: (914)835-4532
Brand Name : UNIVERSAL remote control
Product Name : Mac Filtering Switch
Model Name : MFS-8
This product herewith complies with the requirements of EMC Directive (2004/108/EC)
issued by the Commission of the European Community
Compliance with these directives implies conformity to the following European Community
n EMC Directive
l EN 55022
l EN 55024
l EN 61000-3-2
l EN 61000-3-3
List of test reports and/or certificate verified compliance with the standards above
Date of issue : November 30. 2010
Name and signature of authorized person :
n EMC Directive
l Report No.
l Testing Laboratory : Gumi College EMC Center
James Novak
Senior Product Manager
Universal Remote Control Inc.
Page 15
NOTE
OCE-0076B Rev 02
500 Mamaroneck Avenue, Harrison, NY 10528
Phone: (914) 835-4484 Fax: (914) 835-4532
www.universalremote.com
Loading...