INSTALLATION AND SERVICE INSTRUCTIONS
Keep this booklet for future reference.
The dryer must be fitted by a competent person. In the U.K. Registered Installers undertake to
work to safe and satisfactory standards.
The dryer must be installed in accordance with the Gas Safety (Installation and Use)
Regulations 1998.
Guidance may be obtained from the relevant parts of B.S. 7624: B.S. 5440 parts 1 and 2, B.S.
6891: current editions, I.E.E. Wiring Regulations, and relevant Building Regulations.
Failure to install the appliance correctly could invalidate the warranty liability claims and could
lead to prosecution.
FOR USE IN GREAT BRITAIN AND EIRE WITH NATURAL GAS
ONLY: I2H, GAS SUPPLY PRESSURE : 20 mbar.
THE INSTALLER MUST LEAVE THIS BOOKLET WITH THE
CUSTOMER
Contents
Page
Technical Data . . . . . . . . . . . . . . . . . . . . . . 3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Service instructions . . . . . . . . . . . . . . . . . . 6
Fault Finding . . . . . . . . . . . . . . . . . . . . . . . . 8
Wiring diagram . . . . . . . . . . . . . . . . . . . . . 12
Exploded views . . . . . . . . . . . . . . . . . . . . .13
Parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
THIS APPLIANCE CONFORMS TO THE FOLLOWING EEC DIRECTIVES.
LOW VOLTAGE DIRECTIVE LVD 2006/95/EC:EN60 335-1, EN60 335-2.11.
GAS APPLIANCE DIRECTIVE (GAS) 90/396/EEC:BS 5258:PART 17:1992.
EN 1458-1, 2000 ELECTROMAGNETIC COMPATIBILITY DIRECTIVE 2004/108/
EC:EN55014, EN 61000 - 3 - 2, EN 61000 - 3 - 3, EN 50366
2
WARNING
THIS APPLIANCE SHALL BE
INSTALLED IN ACCORDANCE WITH
THE LOCAL REGULATIONS IN
FORCE AND ONLY IN A WELL
VENTILATED SPACE.READ THE
INSTRUCTIONS BEFORE USING
OR
INSTALLING THIS APPLIANCE.
GENERAL
Front loading tumble dryer with gas heating. Reverse
action drum tumble.Time control. 2-temperature exhaust
thermostat control.Induced air flow enters dryer through
front grille, some passes through the gas burner into the
rear ducting and some into the cooling passages, this
mixed air enters the drum through the rear perforations,
passes through the clothes, lint filter, and the fan and is
discharged through the vent at the rear.
CONNECTIONS
Gas pressure:Rp 1/2 (1/2”B.S.P.parallel internal thread).
Nominally 20mbar
Electric: 230V.50 Hz, earthed supply, 13A fuse.
(wall socket must have efficient earth connection and
correct polarity)
DIMENSIONS
Height 85 cms.(33 1/2”)
Width 59.6 cms.(23 5/8”)
Depth 57 cms.(22 1/2”)
Depth when rear vent hose assembled 60cms.(23 5/8”)
WEIGHT
With packing 37 kg
Without packing 36 kg
SUPPORT
Machine rests on 2 rear positioned rollers and 2 non
adjustable feet.
AIR-FLOW
Approximately 120 cubic metres per hour with capacity
clothes load.
IDENTITY
Manufacture date, and serial number are displayed on a
plate revealed when machine door is open.
The first 4 numerals identify year and week of
manufacture.
The last 6 numerals identify the machine.ALL
INFORMATION FROM THIS PLATE SHOULD BE
QUOTED IN ANY SERVICE COMMUNICATION.
COMPONENTS
DRIVE MOTOR
Permanent split capacitor (8µF)4 pole—Approx. 1/8 HP
Overload protection approx.130°C
BURNER
Pressed steel with slotted flame perforations.
Heat input:3.0kW (10235 Btu/hr).Injector 1.32 mm dia.
3
CONTROL
Type:Pactrol full sequence flame control, P16AGTD(CE)
414601. Ignition electrode gap to burner 3 to 4mm Flame
failure electrode (4213 078 52641).Height from heater
base to centre of electrode 27.0±0.5mm.
INLET THERMOSTAT
(Brown wires identification)
Bi-metal contacts normally closed.
Contacts open if airflow restricted.
Contacts open 130°C ±3°C
Contacts reset 100°C ±5°C
INLET TEMPERATURE LIMITER
(White wires identification)
Bi-metal contacts normally closed.
Contacts open if INLETTHERMOSTATfails.
Contacts open 143°C ±3°C
Contacts reset 100°C ±5°C
EXHAUST THERMOSTATS
Bi-metal contacts normally closed.
Normal Fabrics:Contacts open 60°C ±3°C
60°C (green spot Contacts reset 49°C ±4°C
identification)
Delicate Fabrics:Contacts open 50°C ±3°C
50°C (red spot Contacts reset 35°C ±3°C
identification)
DRUM
Volume 105 litres
Speed approx.50/59 r.p.m.
Capacity 7 kg dry cotton
Rotation clockwise 5 mins., anticlockwise 10 secs
TRANSMISSION
Poly-vee belt driven by vee-grooved motor pulley to outer
circumference of drum.
TIMER
Electric 140 minutes combined forward and reverse 5
min cycle with 10 seconds reverse.
HEATER SWITCH
Single pole, ON/OFF, PUSH-PUSH
R.F.I.FILTER
0.1µF +2x2400pF +2x5mH +2M2
ACCESSORIES
VENT HOSE ASSEMBLY0312 001 01001
WALL/WINDOW VENT KIT0312 005 01001
STACKING KIT0312 003 01001
RESTRAINING KIT0312 006 01001
TECHNICAL DATA
1INSTALLATION
The dryer is designed for installation using a flexible gas
connection with tubing in accordance with B.S.669.
Ensure that the supply gas sizing is adequate.
When installing, position the appliance so that the plug is
accessible.
An electric supply cord with moulded-on 13 Amp.plug is
fitted at the back of the dryer.The length is 1.5 m.(5ft.).
If there are any other appliances that are relatively high
rated (eg a central heating boiler)fed from the same gas
supply branch.It is advisable to perform the verification of
inlet pressure with both appliances in operation.
Prior to installation, check that the local distribution
conditions, nature of gas and pressure and adjustment of
the dryer are compatible.
2 AIR SUPPLY
The tumble dryer shall be installed in a room or internal
space having an openable window, or equivalent.The
customer must be advised that this must be kept open
during use.
Purpose provided ventilation of 100cm shall also be
provided where the room volume is less than 3.7m 3/kw
of appliance rated heat input.
Additional guidance on the provision of air supply may be
obtained from BS5440 parts 1 and 2 and BS 7624:2004
If the dryer is to be installed in a room or internal space
that
already contains one or more fuel burning appliances, the
ventilation requirements above, together with any
additional requirements of BS5440-2:2000, 5,5 shall be
applied.
3 POSITION
The dryer must not be installed in a bedroom, bathroom
or shower room.
Great care is required in the location of the dryer in
premises where concentrations of flammable vapours
may accumulate, e.g.commercial garages and associated
workshops.
The dryer can be placed against a wall, other appliances,
kitchen furniture and similar surfaces.
4 VENTING
The dryer must be fitted with an exhaust vent hose and
the
end either hung out of a window or fitted to a wall/
window vent connection.
Note: Do not obstruct or add a mesh to the vent hose
outlet during use and ensure that it cannot be blocked or
bent sharply which obstruct the air flow.
It is recommended that the interior of the hose be
periodically inspected and cleaned if necessary.
PERMANENT VENTING
Accessory wall/window vent kit CL005 is available:
See illustration for necessary hole through wall.Dim A=
200mm and Dim B= 100mm for direct alignment.
Note DimBmay be increased to 200mm to facilitate easier
drilling if required.
5 POSITION OF DRYER AND CONNECTIONS
The illustration shows the minimum space required by the
dryer and the position of the gas wall connector.It is not
acceptable to use a forward facing mounting plate because
of the space limitation.The sideways facing assembly must
be used and this should be fitted so that the flexible hose
hangs down from the bayonet connector.
A 13 Amp socket must be provided within a distance of 1.4
m (55 in.) of the cable entry into the dryer.The socket must
have an efficient earth connection.
If the dryer is to stand on a surface above the floor or on
top of a washing machine (using the Stacking Kit) then the
750 mm dimension is measured above the supporting
surface.
If the dryer is installed under a worktop there must be a
minimum gap of 15 mm between the top of the dryer and
the underside of the worktop to allow for ventilation.
If it is intended to move the dryer regularly for use then the
Restraining Kit must be fitted to prevent possible damage
to the gas connection.
We also recommend the fitting of a restraining kit to any
dryer which is stacked.
If using accessories:
Wall/Window Vent Kit
Stacking Kit
Restraining Kit
See separate fitting instructions included with each Kit.
INSTALLATION
4
6. OPERATIONAL CHECK
6.1 Remove the pressure test point screw from the gas
tee connection at the back of the dryer and connect
a gas pressure gauge.
6.2 Check that the dryer timer is in the 'off' position, and
that the heat switch is set to 'high'.
Remove anything from inside the drum, check that
the lint filter is fitted, shut the dryer door.
6.3 Turn on the gas, push the electric plug into the socket
and switch on the electricity supply.
6.4 Turn the timer clockwise to a setting of at least 30
mins.Check for ignition.If the gas fails to remain lit
then repeatedly turn the timer on and off (or open
and close the door and push the start switch) for
periods of at least 30 seconds until the air is
removed from the system and burning is continuous.
Note that gas is not lit when the drum is turning anticlockwise.
6.5 With the gas burning ensure that the pressure is as
detailed in the Technical Data.Turn off and replace
the pressure test point screw.Check for soundness.
6.6 Switch on again and re-start so that the gas is
burning.Disconnect the flexible gas hose and check
that the solenoids can be heard to close.After 30
seconds turn on the gas and check that there is no
re-ignition.Switch the machine off and on again and
check for re-ignition.
6.7 Check that the operation of the machine does not
cause spillage of products of combustion from any
open flued gas appliance in the same room, or from
appliances in adjoining rooms, e.g.a gas fire or
central heating boiler.
6.8 In the event of an electrical fault after installation of
the appliance, preliminary electrical system checks
must be carried out (i.e.earth continuity, polarity and
resistance to earth).
6.9 IMPORTANT INFORMATION RE-FUNCTIONING
OF THE FULL SEQUENCE FLAME CONTROL
BOX.
THE FULL SEQUENCE FLAME CONTROL BOX
ON THIS APPLIANCE REQUIRES A 6 SECOND
RE-SET PERIOD FOLLOWING EACH
INTERRUPTION OF INPUT VOLTAGE.
6 SECONDS DELAY IS REQUIRED BETWEEN
EACH ATTEMPT TO RESTART THE APPLIANCE
FOLLOWING SWITCHING IT OFF, OR AFTER
OPENING THE DOOR.
7 AIRFLOW
It is most important that airflow to the plinth is not
restricted.
8 MAINTENANCE
This appliance does not require an annual service
unless it is required as part of a landlord's gas
safety certificate.
If you do have any maintenance activity carried out,
it should be carried out by a competent person (i.e.
registered Engineer).
9 STACKING
Instructions for stacking, if required, are supplied
with the stacking kit.
PROGRAMME
Clockwise rotation of the control knob closes switch
contacts within the timer to:a) energise the drive motor,
and b) energise the full sequence flame controller.
The timer switch controlling the drive motor and the timer
motor, remains closed until the timer motor mechanism
returns the control knob to the '0' position.The timer
switch controlling the full sequence flame controller
opens 12 minutes earlier to provide a cool-down period.
The full sequence flame controller opens the tandem
solenoid gas valves after a delay time of about 8 seconds
and operates the pulsing spark ignition.If the flame is not
detected by the flame failure electrode within 10 seconds
then the valves are closed.The system must then be reset by switching the machine off and re-starting.
The heat selector switch provides options for either 60°C,
or 50°C, exhaust thermostat control.This results in the
burner cycling on and off giving Ionger than anticipated
drying times.Drying times vary depending on the weight
and size of the articles, type of fabric, dampness etc.
These thermostats turn off the heating towards the end of
the chosen cycle and so avoid waste of energy.The lower
temperature thermostat prevents delicate fabrics from
getting too hot with possible risk of damage.
An inlet thermostat is fitted in the ducting at the back of
the dryer.It may also operate under certain other
conditions of restriction of the air-flow, for example, an
overloaded drum or blocked lint filter.This thermostat
switches off the flame controller.This will result in the
burner cycling on and off giving longer than anticipated
drying times.
Should the thermostat fail there is an inlet cut-out
connected in circuit with the gas valves.After operation,
the cut-out must be re-set by switching OFF/ON the
mains supply, to restore heating but a service call may be
required to correct the initial fault.
The conditions of failure of the air flow, blow-back, or of
gas interruption are detected by the flame failure
electrode and the system is shut-down.
Both drum rotation and heater control are switched off
when the door is opened and switched on when the door
is reclosed, and the start button pressed.
For programme times see chart on dryer control panel.
Note:Do not allow fluff to accumulate around the dryer.
5
SERVICE INSTRUCTIONS
RECOMMENDATIONS FOR DISMANTLING
Note:Re-assembly should be done in reverse
sequence to these instructions.
Terminal Block (28),Control Unit (10),Timer (211),
Heat Switch (235),Neon (213),Micro-Switch
Assembly (248),Control Panel (353).
Withdraw 3 screws from the back flange of the Table Top
Assy.(386) and lift and move it rearwards for removal.
This gives access to the 2-screws securing the Control
Unit Bracket (11) to the top flange of the Cabinet.
Pull off the Timer Knob (352) by means of a loop of thin
insulating wire inserted behind it, to expose the 2-screws
securing the Timer (211) to the Control Panel (353).
To remove the Neon (213) disconnect the faston
connectors and push the neon out of the control panel.
To remove the Control Panel (353), disconnect the faston
connectors from the Timer, Neon, and Heat Switch.
Withdraw 3-screws securing the Control Panel lugs to the
Cabinet top rail.Tilt the Control Panel so that the bottom
lugs can be freed from the top flange of the Front Panel
(376).
To remove the door Micro-Switch Assy.(248), withdraw
the 3-screws securing the Control Panel lugs to the
cabinet top rail and free the Control Panel Assy from the
top flange of the Front Panel.Open the door and
withdraw 2 screws securing the Micro-switch Assy, to
the Front Panel, unclip the wires from the top flange of
the Front Panel, lift out the Assy, and disconnect the
faston connectors.
REAR ACCESS LOWER
Exhaust Thermostats (229,250),Motor Assembly
(101),Fan Assembly (446),Capacitor (112).
Withdraw the 6 screws securing the Cover Plate (19) to
the Back Panel (24) and remove it.Pull out the Exhaust
Tube (30).
This gives access to the Exhaust Thermostats (229, 250),
which are each secured to the Banjo (440) by a screw.
Note:The 50°C thermostat is identified by a red spot on
the body.
REAR ACCESS LOWER (continued)
To remove the Motor (101) the belt (125), must first be
removed from the Motor.Disconnect the Motor leads.
Withdraw the black headed pin (537).Exert an anticlockwise force to disconnect the bayonet fitting between
the Fan Access Cover (447) and the back of the Banjo
Assy (440).From underneath the dryer withdraw the 4screws (396) securing the Motor Bracket (432) to the
cabinet base.Lift out the Motor and Fan Assy.
Special tool (7813 002 61111) is recommended when
installing a new belt which needs to be levered and
stretched onto the motor spindle (see illustration).
A capacitor (112) is mounted to the motor assembly
Disconnect the wires to the capacitor before removing the
capacitor or the motor capacitor assembly.
The fan (446) is secured to the Motor Shaft by the Spring
Clip (448) and the finger on the Fan Boss must be lifted
before the fan can be withdrawn from the Motor Shaft.
It is important that rigid support is provided to the
motor shaft when the fan is being refitted.This is to
avoid disturbance of the motor bearings from their
location.
On reassembly of the fan access cover (447) it is
important to hold the protruding finger grip at a “2 o-clock”
position to find location.Push the cover fully on to the fan
chamber prior to rotating it clockwise and engaging tightly
in al 3 locations.Re-insert the black headed pin (537).
HEATER ASSEMBLY REMOVAL
Heater Assy.(32),Solenoid Coil (45 or 45A),Flame
failure Electrode (33),Ignition Electrode (39).
Withdraw the 2-screws securing the Plinth (199) to the
Cabinet, unhook the bottom edge fixing, and remove it.
Separate the 4-way Housing (31) to release the wiring
from the Heater Assy.to the Cabinet.
Lay the dryer flat on its front, supported to take the weight
from the door and controls.
Withdraw the 6-screws securing the Cover Piate (19) to
the Back Panel (24) and remove it.Pull out the Exhaust
Tube (30).
Withdraw the 4-screws securing the Hot Air Elbow Assy.
(20) to the Back Panel (24) and remove it.
Disconnect the External Feed Pipe (15) from the Tee
Piece (27).
Pull the connectors off the Flame failure Electrode (33)
and the ignition Electrode (39).
6
TO RELAX
MOTOR CLIPS
Withdraw the 3-screws and shakeproof washers (13)
securing the Flame Tube Assy.(34) to the Cabinet Base.
Note:On re-assembly the shakeproof washers must be
replaced to ensure a good earth connection.
Lift out the Heater Assy.
To remove either solenoid coil (45 or 45A) disconnect the
electrical connectors, unscrew the nut (44).
To remove the sensing electrode (33), withdraw the screw
(41) lockwasher (482) and nut (411) securing it to the
Flame Tube Assy.(34).Note on re-assembly the
lockwasher (482) must be replaced to ensure a good
earth connection.
To remove the Ignition Electrode (39), withdraw the screw
securing it to the top of the Heater Tube Assy.(34).
If there is a fault in the valves, burner or other parts of the
gas line, then the Heater Assy.(32) must be replaced.
INLET THERMOSTAT & THERMAL OVERLOAD CUTOUT (TOC) REMOVAL
Lay the dryer flat on its front, supported to take the weight
from the door and controls.
Withdraw the 6-screws securing the Cover Plate (19) to
the Back Panel (24) and remove it.Pull out the Exhaust
Tube (30).Disconnect the Fasten connectors from the 4way Terminal Block (142) as necessary (see wiring
Diagram for colour code).Cut off the 2-Cable Ties (387).
Note:on reassembly these must be replaced by new
components to secure thermostat wiring away from
contact with the drum.
Withdraw the 16-screws securing the Rear Banjo (18)
and lift it off.
Withdraw the screws securing the Thermostat (230)
and/or TOC (38) and pull the connecting wires through
the Grommet (25).
Note:Operation of the TOC should only occur if the
thermostat has failed.If the TOC should also fail this
results in high temperatures in the dryer.
REAR ACCESS UPPER
Rear Seal Assy.(14),Drive Belt (125),Drum (266),
Drum Shaft and Bearing (270).
Remove the table top assembly (386) and disconnect the
Faston terminals from the 2-way Terminal Block (28).
Lay the dryer flat on its front supported to take the weight
from the door and controls.
Withdraw the 6-screws securing the Cover plate (19) and
remove it.Pull out the Exhaust Tube (30).
Withdraw the 4-screws securing the Hot Air Elbow (20)
and remove it.
Disconnect the External Feed Pipe (15) from the T-piece
(27).
Withdraw the 16-screws securing the Rear Banjo (18)
and lift it off.
Disconnect the Faston connectors from the Inlet
Thermostat (230) and the TOC (38) from the 4-way
Terminal Block (142).
Withdraw the 3-screws (412) securing the Drum Shaft
and Bearing Assy.(270) to the Back Panel (24).
Withdraw the 8-screws securing the Back Panel (24) to
the Cabinet (196).Disengage the T-piece Grommet from
the slot in the Back Panel and lift off.
The Rear Seal (14) can be prised off the inside of the
Back Panel (24) with a screw-driver, but care should be
taken not to damage the inner sheet metal flange.
Remove excess adhesive before fitting the replacement
Rear Sear (14) using the impact adhesive (Scotchgrip
1099).
To remove the Drive Belt (125) it should be disconnected
from the Motor Pulley and lifted off the Drum.
Note:When re-placed the drive belt should be located
within the lines marked on the Drum circumference.
After removing the Drive Belt the Drum Assy.(266) can
be lifted out.
For dismantling the Drum Rear Bearing (270) access to
the Earth Finger (421) securing screw (420) is through a
hole in the back of the Drum.After removal of the Earth
Finger the screw (422) securing the Drum Shaft Assy.
(426) is through a hole in the centre of the back of the
Drum.
Note:It is important that the recess in the head of the
shaft centre screw (422) is filled with electrically
conductive grease, e.g.Electrolube 2G.
When dismantling the Drum Rear Bearing care should be
taken not to allow parts to fall into the space between the
back of the drum and the drum rear seal plate.
FRONT ACCESS
Front Panel (376),Banjo Assembly (440),Front Seal
(442),Front Bearings (441 and 445).
If the Banjo (440) is to be removed then the exhaust
thermostats should first be disconnected or removed as
described in REAR ACCESS LOWER.
Remove the Top Cover (386), the 3-screws securing the
Control Panel lugs to the Cabinet top rail, and the screws
securing the Micro-Switch Assy.- See TOP ACCESS.
Lay the dryer on its back.
Withdraw the 2-screws securing the plinth (199) to the
Cabinet, unhook the plinth fixings and remove it.
Withdraw the 2-screws (357) securing the Latch Guide
(370) to the Front Panel (376) and remove it.
Withdraw the 2-screws securing the Hinge Assembly
(359) to the Front Panel.Remove the Door and Hinge
Assy.
Withdraw 3-screws securing the Front panel to the Banjo
Assy.(440) - 2 in the Front Panel bottom flange and 1
countersunk screw adjacent to the door opening.
Withdraw the 4-screws securing the Front Panel to the
Cabinet.Lift off the Front Panel.
Disengage the Banjo (440) from the front of the Drum
and disengage the location lug with the Cabinet base.
Remove the Banjo Assy.
The Front Bearings Short (441) and long (445) can be
unclipped from the Banjo flange to release the Front Seal
(442).Care is needed to avoid breaking these bearings.
7
Chart 1. Motor does not run
Start
Is there electrical continuity
across both live and
neutral paths of R.F.I.
filter?
Is voltage between L and N
on main terminal block
230V?
Is voltage between input to
door switch and Neutral
230V?
With door closed is output
from door switch 230V?
Is voltage between live and
terminal T2 on door relay PCB
230v when timer is turned on
and start switch depressed?
Is voltage at terminal d1 on
timer 230v when the timer is
turned on?
Is voltage at terminal T3
on door relay PCB 230v
when timer is turned on?
Substitute capacitor. Does
motor run?
Check door closed, timer
ON electrical supply ON.
Depress start switch.
Exchange R.F.I. filter,
does motor start?
Correct as necessary does
motor start?
Check fuse and mains
cable for continuity, does
motor start?
Exchange door switch
does motor start?
Exchange timer. Does
motor start?
Exchange timer. Does
motor start?
No
No
No
Exchange door relay PCB.
Does motor start?
Check br/w wiring from
RFI filter to door switch.
Check connections clean
and tight, does motor
start?
Yes
Yes
Yes
Yes
Refit capacitor, change
motor.
No
Yes
Yes
Yes
Yes
No
No
No
No
No
No
Yes
Yes
No
No
No
Yes
Yes
No
No
Yes
Yes
With motor running does
gas attempt to light?
Does gas light?
Does gas stay on?
Machine operating. Instruct
users as necessary?
Yes
Yes
Yes
Yes
Yes
Refer to chart 3
Refer to chart 4
Refer to chart 2
No
No
Yes
8
FAULT FINDING
In the event of an electrical fault carry out the preliminary electrical system checks i.e.
earth continuity, polarity, and resistance to earth.
Use each chart to locate the fault causing the dryer to operate incorrectly as follows:
Chart No:
1 Motor does not run.
2 Motor runs but full sequence control does not produce ignition spartk.
3 Motor runs, Full Sequence Control produes ignition sparks, but gas does not ignite.
4 Motor runs, gas ignites but burns for only a short period.
Chart 2.
Motor runs but full sequence control does not produce ignition spark
START
With timer ON (30 min) is voltage
between output C2 on timer and
TB-N 230v??
With red wire still disconnected is
voltage between output of heat
selector switch and TB-N 230V at
high heat setting and zero volts at
low setting.
Reconnect the red wire to the
exhaust thermostat. Is voltage
between brown wire in control box
multiway connector and TB-N
230V?
Check condition of ignition
electrode and spark gap is correct
by removing heater assembly.
Does control spark?
Check HT lead is connected to
control and electrode. Does
control spark?
Disconnect the red wire from the
exhaust thermostat.
CAUTION ! IT IS LIVE!
Is voltage between heat selector
switch and TB-N 230v?
Exchange both exhaust
thermostats (150 °C and 60°C)
and inlet thermostat 130 °C
(brown wires).Does control
spark?
Does control spark with high heat
selected?
Ja
No
No
No
No
No
No
No
Yes
Exchange timer. Does control
spark?
Does control spark with low heat
selected?
Change 50 °C exhaust
thermostat. Does control spark?
Exchange heat selector switch.
Does control spark?
Exchange full sequence control
unit. Does control spark?
Exchange full sequence control
unit. Does control spark?
Check continuity of red wire
between timer C2 and heat
selector switch. Are connections
clean and tight. Does control
spark?
No
No
Yes
Yes
Yes
Yes
Yes
Yes
No
No
Refer to
chart 3
Refer to
chart 4
Does gas light?
Does gas stay on?
Machine operating. Instruct users
as necessary.
Yes
Yes
No
No
Yes
Yes
Yes
Yes
No
Yes
No
Yes
Yes
Yes
9
Chart 3. Motor runs Full Sequence Control produces ignition sparks, but gas does not ignite.
Is voltage between input and
neutral on each solenoid 230v?
Whilst control is sparking is
voltage at terminal 4 of control
unit 230V?
Check continuity of wiring
between 4 Way housing and
relevant solenoid also neutral
wiring. Check plug clean and
tight.
Does gas light?
Exchange Heater Assembly.
Does gas light?
Using the looping connections
on the terminal block on the
base at the rear, check that the
voltage to the solenoids is 230v
whilst the control is sparking
Remove plinth 199. Can gas be
lit manually?
Start
Check spark gap continuity of
H.T. lead and electrode not
cracked. Does burner light?
Exchange control unit. Does gas
light?
No
Yes
Yes
Does gas stay on?
Yes
No
Whilst control is sparking is
voltage at gas control relay PCB
terminal T1 230v?
Yes
No
Check gas control relay wiring.
Exchange if wired correctly. Does
gas light?
Yes
Check wiring between control
unit and 4 Way Terminal block. If
necessary exchange 143°C
inlet temperature limiter. Does
gas light?
Yes
Yes
Yes
No
Yes
No
No
No
Fault in gas system rectify as
necessary.
Yes
No
Exchange solenoid coils in turn.
Does gas light?
Yes
No
No
Yes
Refer to Chart 4
Machine operating. Instruct user
as necessary.
Yes
No
No
No
10
Chart 4. Motor runs, gas ignites but stays on for only short period
Before proceeding, ensure polarity of 13Amp supply socket and earthing is correct
Is flame failure electrode
correctly positioned, and
undamaged? Is wire to terminal
9 undamaged and connections
tight? Is rear drum seal
complete? Is rear elbow and
plinth attached correctly?
Exchange full sequence control
and/or gas control relay PCB
and/or thermostats as
necessary until gas stays on.
Is weight of load suitable? Is
filter clean? Is vent hose or
terminal unobstructed? Is vent
terminal unaffected by wind
conditions that may cause back
pressure?
Start
No
No
No
No
Check gas pressure with all other
appliances in operation does gas
stay ON?
Rectify as necessary does gas
stay ON?
Yes
Yes
Yes
Yes
Yes
Machine operating. Instruct user
as necessary.
11
12
URBAN CHOICE ECO 43A_
403
394
369
196
386
248
370
376
199
11
10
URBAN CHOICE ECO 43A
_
EXPLODED VIEW 1
357
354
366
365
364
363a
363
203a
359
367
362
201
203
13
353
352
211
391
235
372
213
249a
249b
497
15
16
17
393
375
230
38
389
375
18
375
20
23
21
22
412
375
19
403
396
24
25
26
27
25
14
13
143
398
28
141
408
409
410
411
144
URBAN CHOICE ECO 43A
EXPLODED VIEW 2
REAR ASSEMBLY VIEWED FROM FRONT
14
248
440
442
441
445
446
447
448
356
250
229
406
13
32
29
30
31
456
458
459
445
454
455
457
URBAN CHOICE ECO 43A_
EXPLODED VIEW 3
INTERNALS VIEWED FROM REAR
15
URBAN CHOICE ECO 43A_
EXPLODED VIEW 4
INTERNALS VIEWED FROM REAR
142
112
101
101a
427
266
444
125
270
16
432
375
39
41
33
482
411
45
31
13
32
URBAN CHOICE ECO43A_
Exploded View 5
17
ECO43A_
PARTS LIST
Item Description Part Number Expl. View
10 Control Unit 4213 092 25451 1
11 Control Unit Bracket Assembly 4213 070 08623 1
13 Screw M4 x 10 8213 130 37161 2,3&5
14 Rear Seal Assembly 4213 092 08511 2
15 External Feed Pipe (Bundy Tube Assy 3) 4213 089 0788_ 2
16 Gas Inlet Connector 4213 078 49504 2
17 Restrainer Plate 4213 070 08741 2
18 Rear Banjo 4213 080 08361 2
19 Cover Plate (access) 4213 070 08603 2
20 Hot Air Elbow Assembly 4213 089 0791_ 2
21 Air Channel/lnsulating Plate Assembly 4213 089 07901 2
22 Air Guide 4213 070 08551 2
23 Cable Clip 4213 078 26231 2
24 Back Panel Assembly 4213 089 07892 2
25 Grommet 4213 077 08092 2
26 Captive Nut No 8 ’U’ Type 8213 130 37711 2
27 Tee Piece/Test Nipple/Plug Assembly 4213 092 08461 2
28 Terminal Block - 2 Way 4213 078 44621 2
29 Exhaust Elbow Assembly 4213 092 08521 3
30 Exhaust Tube 4213 077 48013 3
31 4 Way Housing Assembly 4213 092 08431 3 & 5
32 Gas Burner Assembly 4213 092 08441 3 & 5
33 Flame Failure Electrode 4213 092 19801 5
38 Inlet Temperature Limiter 143 Deg C 4213 092 24151 2
39 Ignition Electrode 4213 092 08491 5
41 M4 x 10 Pan Screw 2522 180 40002 5
45 Solenoid Coil (SCEM) 4213 092 08501 5
101 Motor and Capacitor Assembly 4213 092 25611 4
101a Motor (Ceset/Olmo) see 101 4
112 Capacitor 8µf 4213 092 08091 4
125 Drive Belt 4213 092 18601 4
141 Mains Cable 4213 076 35123 2
142 Terminal Block 4213 078 44613 4
143 Interference Filter 4213 078 52551 2
144 Earth Tab 4213 092 41181 2
196 Cabinet Assembly - Mid White 4213 092 45591 1
196 Cabinet Assembly - Silver 4213 092 36261 1
199 Plinth Assembly - Mid White 4213 092 45691 1
199 Plinth Assembly - Silver 4213 089 10351 1
201 Door Seal 4213 077 08344 1
203 Complete Door Assembly - Mid White 4213 092 46271 1
203 Complete Door Assembly - Chrome 4213 092 36281 1
203a Door Frame Assembly - Mid White 4213 092 46361 1
203a Door Frame Assembly - Chrome 4213 092 36091 1
211 Timer T600 - Mid White 4213 078 57541 1
211 Timer T600 - Silver 4213 078 57551 1
213 Neon Assembly 4213 078 50401 1
ECO43A_
PARTS LIST
229 Exhaust Thermostat 60 Deg C 4213 078 53001 3
230 Inlet Thermostat 130 Deg C 4213 092 24161 2
235 Electronic Start Assembly 4213 092 46461 1
248 Micro Switch Assembly 4213 092 05251 1 & 3
249a Gas Control Relay assembly 4213 092 51871 1
249b Gas Control Relay assembly 4213 092 51871 1
250 Exhaust Thermostat 50 Deg C 4213 078 49453 3
266 Drum Assembly 4213 092 08451 4
270 Drum Shaft/Bearing Kit 4213 092 05591 4
352 Timer Knob Assembly - Mid White 4213 092 45741 1
352 Timer Knob Assembly - Silver 4213 092 43331 1
353 Control Panel Assembly - Mid White 4213 092 51981 1
353 Control Panel Assembly - Silver 4213 092 51991 1
354 Locator Peg 4213 077 61281 1
356 6G*3/8 DP/PWABE/NIBS/TSZPC 8213 130 38051 3
357 8Gx1 P/F AB S/TS MECH ZPC 8213 130 38101 1
359 Hinge Assembly 4213 092 25361 1
362 Window 4213 077 4409_ 1
363 Door Frame - Mid White 4213 077 92271 1
363 Door Frame - Chrome 4213 077 82721 1
363a Door Handle - Mid White 4213 077 92351 1
363a Door Handle - Silver 4213 077 82861 1
364 Latch Pivot 4213 075 13013 1
365 Latch Spring 4213 075 70833 1
366 Door Latch 4213 077 53413 1
367 Switch Strike 4213 077 83571 1
369 Loom Clip 4213 075 70941 1
370 Latch Guide 4213 077 40992 1
372 Timer Bracket 4213 070 10933 1
374 Pan Screw St M3 x 5 2522 180 40001 1
375 6 x 3/8 Earth Screw MZP 8213 130 38051 2 & 5
376 Front Panel Assembly - Mid White 4213 092 45681 1
376 Front Panel Assembly - Silver 4213 092 36301 1
386 Table Top Assembly - Ellipse - Mid White 4213 092 46211 1
386 Table Top Assembly - Ellipse - Silver 4213 092 43371 1
387 Cable Tie 4213 077 41772 1
389 Screw 6AB x 6.5 2522 165 20003 2
391 Ellipse Button Assembly - Mid White 4213 092 45781 1
391 Ellipse Button Assembly - Chrome 4213 092 44871 1
393 Flex Support Clip 4213 077 40982 2
394 Foot 4213 077 39833 1
396 Flb Ear Scr St Zn 8 x 3/8 2513 202 01006 1, 2 & 3
398 Screw M4 x 25 2522 180 40003 2 & 4
403 Roller Assembly 4213 092 35651 1 & 2
ECO43A_
PARTS LIST
447/1 Access Cover Assembly 4213 092 18081 4
408 Cable Clamp 2 4213 077 47303 2
409 Washer M5 Form A 2522 604 60002 2
409 M5 Form A Washer 2522 604 60002 3
410 Screw 6 x 1/2 2522 165 20004 2
411 M4 Hex Nut 2522 402 50001 2 & 5
412 Screw No 10-24 UNC x 3/8” 8213 130 31051 2
427 Motor Retaining Clips 4213 078 4536_ 4
432 Motor Mounting Bracket 4213 080 0675A 4
434 Loom Strap 4213 078 46311 3
435 M8 Shakeproof Washer 8213 130 28961 3
436 M8 Hex Nut 8213 130 38091 3
440 Banjo Assembly 4213 089 11992 3
441 Front Bearing (short) 4213 077 40952 3
442 Front Seal 4213 077 4094_ 3
443 8 x 5/8 Recessed Pan Head Screw 8213 130 38021 4
444 Lifter 4213 077 41009 4
445 Front Bearing (long) 4213 077 40962 3
446 Fan 4213 077 4089_ 3
447 Access Cover (fan) n/a 3
448 Fan Spring Clip 4213 075 71162 3
451 Fln Tap Scr St Zn 8 x 1/2 2513 153 01003 1
454 Filter 4213 092 17821 3
455 Screw 6 x 12 2522 166 30001 3
456 Banjo Seal 4213 077 07992 3
458 Banjo Insert No 2 4213 077 53502 3
459 Banjo Insert No 1 4213 077 53492 3
482 M4 Toothed Lockwasher 2522 616 15007 5
497 Switch Cover 4213 177 01141 1
537 W’ Button (access cover) 4213 078 26311 4
555 Rear Panels Seal Kit 4213 092 28001 2
NOT SHOWN ON EXPLODED VIEW
Bearing Pads & Brush Seal Kit 4213 092 21171
Loom Assembly 4213 176 01421
Instructions for Use 4213 177 79451
Manufactured by: Crosslee plc. Lightcliffe Factory, Hipperholme, Halifax, West Yorkshire, HX3 8DE
ECO 43A_ Installation/Service Book 4213 094 79421
Loading...