Upright SB-80 Operator's Manual

Page 1

:$51,1*

All personnel shall carefully read, understand and follow all safety rules, operating instructions, and the Scaffold Industry

Association’s

Manual of Responsibilities (ANSI A92.5)

before operating or performing maintenance on any Upright boom

supported aerial work platform.

B054CHAD;4B

SB-80

BTaXP[=^ c^2daaT]c

Electrocution Hazard Tip Over Hazard

Collision Hazard

Fall Hazard

NEVER

operate the machine within ten (10) feet of power lines.

THIS MACHINE IS NOT INSULATED

NEVER

operate the boom or drive with platform elevated unless on firm, level surface. (Plus3 machine 3°)

NEVER

position the platform without first checking for overhead obstructions or other hazards.

NEVER

climb, stand or sit on platform guardrails or midrail.

0;;

_SSe`Q^dc ]ecd gUQb Q^ Q``b_fUT VQ\\ bUcdbQY^d `b_`Ub\i QddQSXUT d_ TUcYW^QdUT `\QdV_b] Q^SX_bQWU

`_Y^d 1ddQSX _^\i _^U VQ\\ bUcdbQY^d d_ UQSX Q^SX_bQWU `_Y^d

=4E4A

UhSUUT ]QhY]e] `\QdV_b] \_QT _V & \Rc "'" [W Q^T dg_ " _SSe`Q^dc

=4E4A

UhSUUT $% \Rc " > _V cYTU V_bSU `Ub _SSe`Q^d

38BCA81DC4

Q\\ `\QdV_b] \_QTc UfU^\i _^ dXU `\QdV_b]

=4E4A

_`UbQdU dXU ]QSXY^U gYdX_ed VYbcd cebfUiY^W dXU g_b[ QbUQ V_b cebVQSU XQjQbTc ceSX Qc X_\Uc Tb_`

_VVc Re]`c SebRc _b TURbYc+ Q^T Qf_YTY^W dXU]

>?4A0C4

]QSXY^U _^\i _^ cebVQSUc SQ`QR\U _V ce``_bdY^W gXUU\ \_QTc

=4E4A

U\UfQdU dXU ]QSXY^U gXU^ gY^T c`UUTc UhSUUT "( ]`X !"% ]cUS

8= 20B4 >5 4<4A64=2H

`ecX U]UbWU^Si cd_` Redd_^ d_ TUQSdYfQdU Q\\ `_gUbUT Ve^SdY_^c

0;F0HB

S\_cU Q^T cUSebU c\YTY^W bQY\ QVdUb U^dUbY^W `\QdV_b] >5F5B UhYd _b U^dUb `\QdV_b] gXY\U U\UfQdUT

=4E4A

ecU \QTTUbc cSQVV_\TY^W _b _dXUb YdU]c d_ WQY^ XUYWXd+ g_b[ _^\i Vb_] dXU `\QdV_b] V\__b

=4E4A

S\Y]R T_g^ U\UfQdY^W QccU]R\i gXY\U `\QdV_b] Yc U\UfQdUT

8=B?42C

dXU ]QSXY^U dX_b_eWX\i V_bSbQS[UT gU\Tc \__cU _b]YccY^W XQbTgQbU XiTbQe\YS \UQ[c \__cU gYbU

S_^^USdY_^c Q^T TQ]QWUT SQR\Uc _b X_cUc RUV_bU ecY^W

E4A85H

dXQd Q\\ \QRU\c QbU Y^ `\QSU Q^T \UWYR\U RUV_bU ecY^W

=4E4A

ecU Q ]QSXY^U dXQd Yc TQ]QWUT ^_d Ve^SdY_^Y^W `b_`Ub\i _b XQc TQ]QWUT _b ]YccY^W \QRU\c

85 0;0A< B>D=3B

gXY\U R__] Yc U\UfQdUT CD?@ SQbUVe\\i bUdbQSd R__] Q^T \_gUb `\QdV_b] gYdX_ed

b_dQdY^W =_fU ]QSXY^U d_ Q VYb] \UfU\ cebVQSU

=4E4A

QddQSX _fUbXQ^WY^W \_QTc _b ecU R__] Qc Q SbQ^U

=4E4A

Q\dUb _`UbQdY^W _b cQVUdi cicdU]c gYdX_ed ]Q^eVQSdebUbc gbYddU^ S_^cU^d

=4E4A

SXQbWU RQddUbYUc ^UQb c`Qb[c _b _`U^ V\Q]U 3XQbWY^W RQddUbYUc U]Yd Uh`\_cYfU XiTb_WU^ WQc

=4E4A

bU`\QSU Q^i S_]`_^U^d _b `Qbd gYdXQ^idXY^W_dXUb dXQ^ _bYWY^Q\ E`BYWXd bU`\QSU]U^d `Qbdc gYdX_ed

dXU ]Q^eVQSdebUbµc gbYddU^ S_^cU^d

=4E4A

d_g dXU ]QSXY^U DbQ^c`_bd Ri dbeS[ _b dbQY\Ub _^\i

05C4A DB4

 cUSebU dXU g_b[ `\QdV_b] Vb_] e^QedX_bYjUT ecU Ri deb^Y^W R_dX [UicgYdSXUc _VV Q^T bU]_fY^W

[Ui

2P[XU^a]XP ?a^_^bXcX^] %$ FPa]X]V

7Qc_\Y^U Q^T TYUcU\ U^WY^U UhXQecd Q^T c_]U _V dXUYb S_^cdYdeU^dc QbU [^_g^ d_ dXU CdQdU _V 3Q\YV_b^YQ d_

SQecU SQ^SUb RYbdX TUVUSdc Q^T _dXUb bU`b_TeSdYfU XQb]

BPUTchAd[Tb>_TaPcX]V8]bcadRcX^]b

ITEM SPECIFICATIONS

Height

Working height maximum 86 ft. Platform height maximum 80 ft. Platform step in height 12 in. Up and over height 7 ft. 6 in. Drivable height 80 ft.

Horizontal outreach

72 ft. Turret rotation 360° continuous Platform rotation 180° Tail swing 3 ft. 3 in. Jib length 8 ft. Jib arc 140°

Inside turning radius

10 ft.

Outside turning radius

23 ft.

Drive speed (lowered)

3.25 mph

Drive speed (elevated)

0.75 mph

Gradeability

Diesel 40% Gas 35%

Controls

Electric Proportional

Tires

15-22.5 x 16 ply

Tires (Plus3 option)

18-22.5 18 ply foam-filled

Dimensions

Platform size 6 ft. std. (8 ft. optional) Guardrail height 45 in. Toeboards 6 in. Maximum platform capacity 600 lbs. (272 kg) Maximum no. of occupants 2 Weight (gasoline) 32,000 lbs. Weight (diesel) 32,500 lbs. Overall height (stowed) 9 ft. Overall length (stowed) 37 ft. 8 in. Overall width (retracted) 8 ft. in. Overall width (extended) 10 ft. 6 in. Overall width (Plus3) + 4 in. Wheel base 9 ft. 6 in. Wheel track 59 in. Ground clearance 11 in.

Power source (gasoline)

GM 3.0 liter 70 HP

Power source (diesel)

Perkins 1004-42 86 HP

System voltage

12VDC

Maximum hydraulic pressure

5000 psi

ITEM SPECIFICATIONS

Reach Envelope Diagram

PECIFICATIONS

TEL: (800) 559 926-5438 or (559) 891-5200 FAX: (559) 896-9012 PARTS: (888) UR-PARTS PARTSFAX: (559) 896-9244 1775 Park St., Selma, CA 93662 http://www.upright.com

P/N 102320-000 102320-000-9903-.2-D

*Specifications subject to change without notice. Refer to Service Manual for complete parts & service information. Meets or exceeds all applicable requirements of OSHA & ANSI A92.5-1992

Local Distributor:

>_TaPc^a<P]dP[

Page 2

287,1(6(59,&(

Use the following table as a guide for routine maintenance. Inspection and maintenance shall be

performed by personnel who are trained and familiar with mechanical and electrical procedures. Refer to the Service Manual for complete

service instructions. Please copy this page and use the Routine Service

Table as a checklist when inspecting a machine for service.

Routine Service Table Key

Interval

Daily=each shift or every day or every 8 hours 50h/30d=every 50 hours or 30 days 125h/3m=every 125 hours or 3 months 250h/6m=every 250 hours or 6 months 1000h/2y=every 1000 hours or 2 years

Y=Yes/Acceptable N=No/Not Acceptable R=Repaired/Acceptable

COMPONENT

INSPECTION OR SERVICES

INTERVALYN

Battery

Check electrolyte level 6m Clean exterior & terminals 3m Check battery cable condition Daily

Engine Oil and Filter

Check level and condition Daily Check for leaks Daily Change oil filter 00h

Engine Fuel

System

Check fuel level Daily Check for leaks Daily Replace fuel filter 6m Check air cleaner Daily

Engine Coolant

Check coolant level (with engine cold) Daily Replace coolant 3m

Hydraulic Oil (*See note)

Check oil level Daily Change filter 6m Drain and replace oil 2y

Hydraulic

System

Check for leaks Daily Check hose connections 30d Check hoses for exterior wear 30d

Emergency

Hydraulic

System

Operate the emergency lowering valve and check for serviceability

Daily

Controller Check switch operation Daily

Control

Cable

Check the exterior of the cable for pinching, binding or wear

Daily

Platform

Deck and

Rails

Check fasteners for proper torque Daily Check welds for cracks Daily Check condition of operators manual Daily Check condition of anchorage points Daily Check condition of deck Daily

Tires

Check for damage Daily Check air pressure (100 psi) [7 bar] Daily Check lug nuts (torque to 260 ft. lbs. [352 Nm]) 30d

Hydraulic

Pump

Wipe clean 30d Check for leaks at mating surfaces 30d Check for hose fitting leaks Daily Check mounting bolts for proper torque 30d

Hydraulic

Drive

System

Check hydraulic drive motor operation Daily Check hoses, fittings, and valve block for leaks Daily

Preventative Maintenance Report

Date: __________________________________ Owner:_________________________________ Model No: ______________________________ Serial No:_______________________________ Serviced By:_____________________________ Service Interval:__________________________

Steering

System

Check hardware & fittings for proper torque 6m Check linkage for wear areas 30d Check for missing/loose retainers Daily Check steering cylinder for leaks 30d

Elevating Assembly

Inspect for structural cracks Daily Check pivot points for wear 30d Check pivot pin retaining bolts for proper torque 30d Check members for deformation Daily

Chassis

Check hoses for pinch or rubbing points Daily Check component mounting for proper torque 6m Check swing bearing bolt (torque to 190 ft/lbs) 6m Check welds for cracks Daily

Lift

Cylinders

Check the cylinder rods for wear 30d Check pivot pin pivot bolts for proper torque 30d Check seals for leaks 30d Inspect pivot points for wear 30d Check fittings for proper torque 30d

Turret

Check ring gear for proper lubrication and wear Daily Check planetary oil level 150h/3m Lubricate ring gear (MoS2 grease) 150h/3m

Torqu e H ub s

Check for leaks Daily Check oil level 250h/6m Change oil after break-in period 50h/30d Change oil (SAE 90 wt. gear oil) 2000H/

Entire Unit

Check for and repair collision damage Daily Check fasteners for proper torque 3m Check for corrosion-remove and repaint 6m Lubricate 30d

Labels

Check for peeling, missing, or unreadable labels & replace

Daily

COMPONENT

INSPECTION OR SERVICES

INTERVALYN

*Use Mobil DTE 15M, ISO grade 46 for temperature range of 40°f to 100°f. For colder climates use Mobil 13M, ISO grade 32, for temperature range of 10° to 65°f.

NTRODUCTION

This manual covers the operation of internal combustion powered models of the SB-80 Boom. This manual must be stored on the machine at all times.

PRE-O

PERATION

& S

AFETY INSPECTION

Carefully read, understand and follow all safety rules, labels, and operating instructions, then perform the following steps eac h day before use.

Perform a complete visual inspection of the entire unit prior to operating. Check the following ar eas for discrepancies:

1. Open panels and check hydraulic components/hoses for damage or leaks. Check electrical components/wiring for damage or loose connections.

2. Inspect chassis, axles, hubs, and steering linkage for damage, deformation, buckled paint, loose or missing hardware, and cracked welds.

3. Check tires for damage, punctures, and inflation; tire pressure must be 100 psi (7 bar).

4. Check all hoses/cables for wear.

5. Inspect elevating assembly for damage, deformation, buckled paint, loose or missing hardware, and cracked welds.

6. Inspect platform and g uardrails for damage, deformation, buckled paint, loose or missing hardware, and cracked welds. ensure that gate operates freely and latches securely.

7. Check Hydraulic fluid level with platform fully lowered.

8. Check fluid level in batteries (see

battery maintenance

page 9).

9. Check fuel level, add fuel if necessary (see

fueling

, page

9).

10. Check engine oil level.

11. Check air filter, replace if necessary.

12. Set gasoline/propane selector to desired position. Set to center position to purge the system when switching fuels. If the machine is to be operat ed on propane , open the supply valve on the tank

Note: When using LP gas, use clean, waterfree liquid petroleum gas, preferably from a bulk storage tank.

13. Ensure that radiator is cold, check coolant level. Add if necessary

YSTEM FUNCTION INSPECTION

Note: Refer to figures 1 through 5 for chassis and platform control locations.

Important: Before performing the System Function Inspection, be sure the axles are fully extended. For axle extending instructions, refer to “Extending and Retracting Axles” (Page 5).

1. Before performing the following tests, check area around machine and overhead for obstructions, holes, drop-offs, and debris.

2. Turn chassis key switch to chassis, and pull out emergency stop switches at the chassis control pane l and at the platform control panel.

3. Retract locking bolt. See figure 1.

4. Press the engine start button to crank the engine; release when engine starts. If engine is cold: press the glow plug button and hold for 20 seconds pr ior t o starting diesel models.

5. Push in the chassis emergency stop button, engine should stop. Repeat for platform emergency stop button. Return both emergency stop buttons to the on position, and start engine.

6. Operate each function switch to raise / lower, extend / retract, rotate left / right, each section of the elevating assembly and observe the operation of the machine. Al l functions should operate through full cycle smoothly.

7. Turn chassis key switch to platform.

8. Mount the platform, and attach approved fall restraint to designated platform anchorage point. Attach only one fall restraint to each point.

Figure 1: Locking Pin

NEVER remove the cap from a hot radiator. Hot coolant can cause severe burns.



:$51,1*



If you smell propane, close the supply v alve on the tank immediately until you have located and corrected the leak.



:$51,1*



Page 3

OTES

1. While engaging the hand interlock, move the drive control handle forward and reverse. Observe that proportional functions operate smoothly, and that brakes apply quickly after control is released.

2. While engaging the hand interl ock, o perate steer s witch to left and right. Observe that steering wheels tu rn properly.

3. While depressing foot switch, operate boom controls. Observe that boom operates smoothly, and that boom raise and lower, turret rotation, and boom extension and retraction operate proportionally in conjunction with stroke of handle. Observe that platform maintains level when boom is elevated.

Note: Boom will not extend or raise beyond 45° unless axles are extended.

4. With the boom elevated five degrees above horizon or greater, o perate dri ve control handle. Obs erve that dri ve speed is limited to creep (1 foot [.30m] per second). Lower upper boom to stowed position.

5. Press the service horn button. Observe that horn is audible.

Note: Foot switch must be depressed to activate any machine function from the platform controls.,

Figure 1: Platform Controls

Figure 2: Platform Controls

ONTROLS

& I

NDICATORS

Figure 3: Chassis Controls

DO NOT use a machine that is damaged or malfunctioning. Tag and remove the unit from service until it is repaired.



:$51,1*



1. Oil Pressure Gauge

2. Water Temperature Gauge

3. Hourmeter

4. Emergency Stop

5. Key Switch

6. Engine Start

7. Glow Plug (Diesel only)

8. Auxiliary Power (for emergency lowering only)

9. Function Enable

10. Boom Control

11. Boom Extension Control

12. Turret Control

13. Jib Control

14. Cage Rotation

15. Cage Level Control

16. Circuit Breaker

Page 4

Figure 1: Platform Controls

PERATION

Before operating work platform ensure that:

Pre-operation and safety inspection has been completed, and any discrepancies have been corrected.

System function inspection has been performed. Operator has been thoroughly trained on the

operation of the machine. Work area is clear of all obstructions, holes, drop-

offs, or persons in the route of trav el. Surface is capable of supporting wheel loads.

Refer to figures 1 through 5 for control locations.

At any time during operation, press the emergency stop button to stop all functions in the event of an emergency.

At any time during operation, press the service horn button to sound an audible warning in necessary.

Figure 2: Typical Fall Restraint Anchorage Point

From the Lower Controls

1. Turn the chassis key switch to chassis position.

2. Press the start button to crank the engine. Release when the engine starts.

3. Diesel Engines: When the engine is cold (less than 15°f); press and hold the glow plug button for 20 seconds prior to starting.

From the platform controls

1. Turn the chassis key switch to platform controls.

2. Turn the platf orm rotary swit ch full y clock wis e to crank the engine. Release when engine starts.

3. Diesel Engines: When the engine is cold (less than 15°f); press and hold the glow plug button for 20 seconds prior to starting.

17. Axle Extend/Retract

18. Lights (optional)

19. Generator (optional)

20. Horn Button

21. Emergency Stop

22. Axles Extended indicator

23. Tilt warning indicator

24. Low oil pressure indicator

25. Torque/Speed selector

26. Fuel selector (Gas only)/ Glow plug (Diesle only)

27. Auxiliary power (for emergency lowering only)

28. Boom Raise/Lower & Turret Rotate control

29. Boom Extend/Retract

30. Cage Rotate

31. Jib Raise/Lower

32. Cage Level

33. Drive control handle/ interlock

34. Engine start

35. Foot interlock switch

Emergency Sto

ALWAYS wear an approved fall restraint

properly attached to designated platform anchorage point when driving or operating the machine (See figure 6).

Attach only one restraint to each anchorage point.

Service Horn



:$51,1*



Starting the Engine

19 21 22

OTES

Page 5

With Boom Lowered

1. Turn chassis key switch to platform, and pull out the chassis emergency stop switch.

2. Mount the platform and close sliding rail.

3. Attach approved fall restraint to designated platform anchorage point. Attach only one fall restraint to each point.

4. Start engine.

5. Check that the area around and above the work platform is clear of obstructions, holes, drop- of fs, persons in the route of travel, and the surface is capable of supporting wheel loads.

6. Engage the interlock switch and move the dr ive control handle forward to travel forward and rearward to travel in the reverse direction.

Note: When the boom is rotated to the front of the chassis (steering wheels aft) directions of travel and steering will be reversed. Observe the color coded arrows on the control panel near the drive control handle, and on the chassis. They will indicate the direction of travel when the drive control handle is moved.

From the Platform Controls

Important: Axles must be fully extended to allow boom extension or boom to be raised above 45°. Machine must be driven forward or reverse while extending axles. Ensure all four wheels can be clearly seen and persons and obstacles are clear of the machine.

1. Drive the machine forward or reverse.

2. Move and hold the axle extend/retract switch to extend.

3. The axles will extend.

4. When axles are fully extended, the axles extended light (green light on platform con troller) will illuminate.

Note: Verify Yellow bars are visible on all four axles at full extension.

5. Re-synchronize the steering geometry by steering full left or full right and holding for a few seconds.

6. All boom functions are now available.

With Boom Elevated

Travel with boom elevated is restricted to firm level surfaces only. (Plus3 machines 3°)

When driving elevated, the machine will travel at creep speed (1 foot [.30 m] per second).

Steering

1. While engaging the interlock, push the steering switch (located on top of the control handle) to the left to turn left, and right to turn rig ht.

Note: Steering is not self centering. Wheels must be returned to the straight ahead position by operating the steering switch.

OSITIONING THE PLATFORM

Positioning the platform as close as possible to the work area requires some planning. First, you must survey the work site to find a suitable place to park the machine. This must be a firm lev e l area as cl ose as possible to the work area. Take int o considerat ion all obstructions on the ground and overhead and avoid them.

Always, before operating any function, check the area around and overhead for any obstructions or electrical conductors.

Multifunction Controls

The UpRight SB-80 employs the use of multifunction controls. This means that functions can operate at full speed simultaneously.

The turret may be rotated while driving if necessary to make turns in tight areas. All other boom functions will not operate while driving.

Driving

Extending and Retracting Axles

NEVER exit the platform while the boom is

elevated. K eep both feet f irmly on platform floor at all times. Do not use planks, ladders, or any other device on the platform for achieving additional height or reach.



:$51,1*



OTES

Page 6

Lower Control Operation

All boom functions will operate at fixed speed.

1. Turn chassis keyswitch to chassis controls.

2. With engine running, operate boom control swit ches t o position the platform.

While depressing the foot switch, move the platform level control s w itch forward to swing the platform upward, rearward to swing the platform downward. Release the switch to stop leveling.

While depressing the foot switch, move the boom rotation joystick to the right to rotate right, left to rotate left. Release the switch to stop rotation. The turret rotation will function at a speed proportional to the stroke of the joystic k. Make su re the area around the boom is clear of all obstructions before rotating the turret.

While depressing the foot switch, move the joystick forward to elevate the boom, rearward to lower the boom. Release the control lever to stop elevating / lowering. The boom elevate will function at a speed proportional to the stroke of the joystick.

While depressing the foot switch, move the boom extension control joystick rearward to extend the boom, forward to retract the boom. Rel ease the control lever to stop extending / retracting. The boom extension will function at a s peed, proportional to the stroke of the joystick.

While depressing the foot switch, push t he jib control switch forward to elevate the jib, rearward to lower the jib. Release the control lever to stop elevating / lowering.

While depressing the foot switch, toggle the control switch left to rotate left, right to rotate right. Release the switch to stop rotation.

NEVER exit the platform while the boom is elevated. Keep both fee t firmly on platform floor at all times. Do not use planks, ladders, or any other device on the platform for achieving additional height or reach.

DO NOT operate the machine if the platform does not maintain level when elevated.



:$51,1*



Leveling the Platform



:$51,1*



Rotating the Turret

Elevating the Boom

Extending the Boom

Elevating the Jib

Rotating the Platform

Figure 14: Label Identification

060197-000

1 REQUIRED

066555-001

2 REQUIRED

066554-000

3 REQUIRED

068639-000

2 REQUIRED

068552-000

2 REQUIRED

005221-000

2 REQUIRED

100341-000

1 REQUIRED

068637-000

2 REQUIRED

068637-001

2 REQUIRED

068632-000

6 REQUIRED

064166-000

1 REQUIRED

027898-001

1 REQUIRED

068979-000

4 REQUIRED

066554-000

3 REQUIRED

068632-000, 6 REQUIRED

066562-005

4 REQUIRED

100346-000

2 REQUIRED

066553-004

4 REQUIRED

066553-001

4 REQUIRED

100340-002

1 REQUIRED

100340-004

1 REQUIRED

066566-000

2 REQUIRED

100340-000

1 REQUIRED

062557-012

1 REQUIRED

100340-003

1 REQUIRED

102249-000

12 REQUIRED

SB-80 Label Identification: All of the labels shown in Figure 14 shall be present and in good condition before operating the work platform. Be sure to read, understand and fo llo w these labels when operat ing the work platform.

Page 7

MERGENCY OPERATION

In the event of an engine failure, the elevating assembly may be lowered using the following procedure

Lowering Elevating Assembly

1. Engage the auxiliary power unit switch.

2. Operate any boom function in the normal manner.

Note: Auxiliary battery is capable of one emergency lowering cycle before requiri ng recharge. Battery is recharged while engine is in operation.

EMERGENCY TOWING

Perform the followi ng only when the machine will not operate under its own power and it is necessary to move the machine or when winching onto a trailer for transportation.

1. Ensure that the platform is fully lowered, and that the turret is rotated so that the platform is to the rear of the machine.

2. Refer to figure 7 and disengage all four drive hubs. Remove two (2) screws and center cap. Reinstall ce nter cap in the opposite direction.

3. When ready to move the machine, remove the chocks. Tow or winch into position and replace chocks.

4. Attach adequate chain/cable of sufficient strength for towing the machine to the front or rear tie down lugs.

5. Engage all four drive hubs by returning the cente r ca ps to their original orientation.

Figure 1: Drive Hub (Operating position shown)

Switching Fuels (Gas/Propane Only)

1. With the engine running push the Fuel Selector Switch to the center position.

2. After the engine has quit runn ing select the appropriate fuel supply.

3. Restart the engine.

FTER USE EACH DAY

1. Ensure that the platform is fully lowered.

2. Park the machine on level ground, preferably under cover, secure ag ainst vandal s, chil dren or una utho rize d operation.

3. Turn the key switch to OFF and remove the key to prevent unauthorized operation.

ACHINES EQUIPPED WITH PLUS

PTION

Machines equipped with Plus3 option are capable of operating all functions on a firm 3° slope.

NEVER climb down the elevating assembly. If controls do not respond, follow the emergency lowering procedure.

DO NOT tow the machine faster than 3 mph. Faster speeds will damage drive components and void warranty.

There are no brakes when the center caps are installed in the inverted position.

Chock wheels before disengaging hubs. Machine may roll.



:$51,1*



&$87,21



:$51,1*



:$51,1*



Do not operate machines with Plus3 option unless machine is equipped with foam filled tires. Remove machine from service and install proper tire/wheel combination before oper ating machine.

If tilt warning sounds and machine will not operate, retract boom, lower pl atform and mov e machine to a firm surface less than 3°.

Drive Hub

Center Cap

Screws



:$51,1*



:$51,1*



Figure 13: Label Identification

065554-000

3 REQUIRED

068635-000

2 REQUIRED

010076-000

2 REQUIRED

100346-000

1 REQUIRED

068637-000

2 REQUIRED

068637-001

2 REQUIRED

066553-004

4 REQUIRED

061205-002

1 REQUIRED

068632-000

6 REQUIRED

005221-000

2 REQUIRED

062814-000

1 REQUIRED

068979-000

6 REQUIRED

066552-000

2 REQUIRED

066555-001

2 REQUIRED

066562-000

6 REQUIRED

066553-004, 4 REQUIRED

066553-001

4 REQUIRED

100345-000

2 REQUIRED

102249-000

12 REQUIRED

SB-80 Label Identification: All of the labels shown in Figure 13 shall be present and in good condition before operating the work platform. Be sure to read, understand and fo llo w these labels when operat ing the work platform.

Page 8

RANSPORTATION

Important: Axles must be fully retracted to transport machine. Machine must be driven forward or reverse while retracting the axles. Ensure all four wheels can be clearly seen and persons and obstacles are clear of the machine.

1. Drive the machine forward or reverse.

2. Hold the axle extend/retract switch to retract.

3. The axles will retract.

4. Re-synchronize the steering geometry by steering full left or full right and holding for a few seconds.

5. The machine may now be loaded for transport.

BY C

RANE

1. Ensure that boom is fully lowered and retracted.

2. Attach straps to chassis lifting lugs only. Ensure that straps are adjusted properly to keep u nit level when lifting.

BY T

RUCK OR TRAILER

1. Ensure that boom is fully lowered and retracted.

2. Maneuver the machine onto bed of truck / trailer.

3. When winching, follow instructions for emer gency towing on page 6. Attach winch cable to front tie down lugs.

4. After winching, ensure that all four drive hubs are engaged by returning the center caps to their original orientation.

5. Secure the machine to the transport vehicle using chains / straps of adequate load capaci ty (r efer to specifications, back page) attached to chassis tie down l ugs. (see figures 8 and 10)

6. Place wooden block (4” x 4” x 36”) under platform support braces as shown. (Figure 9)

7. Attach ratchet strap under platform floor grating, over support braces. (Figure 9) Do not over tighten.

Figure 1: Front Chassis Tie Down Lifting Lugs

Figure 2: Securing the machine for transportation

Figure 3: Rear chassis tie down lifting lugs

Stand clear of machine when lifting. Check specifications on back page , ensure that

crane and slings are of correct capacity to lift weight of unit.

Do not winch machine faster than 3 mph. Faster speeds will damage drive components and void warranty.



:$51,1*



&$87,21



NEVER elevate the machine while on a truck or trailer.



:$51,1*



Chassis Tie Down

Lifting Lugs

Platform Tie

Down Bracket

Wooden Block

4” x 8” x 36”

Support Braces

Chassis Tie Down

Lifting Lugs

AINTENANCE

UELING

Diesel

1. Open left turret cover, open fill pipe cap. (see figure 11)

2. Fill to capacity with diesel motor fuel only, grade #1-D, or #2-D. Use distillate fuel only, do not use residual or blend.

3. Fuel tank full capacity is 42 US gallons.

YDRAULIC OIL

1. Open left turret cover and check oil leve l a t si ght gauge with the boom stowed and retracted. Engine runni ng or stopped. (see figure 12)

2. If necessary, fill to capacity with clean ISO compatible hydraulic oil. Refer to Routine Service Table on page

12.

3. Clean area around cap before opening.

4. Open filler / breather cap to add hydraulic oil.

5. Replace cap.

UBRICATION

Refer to service manual for lubrication chart and guidelines.

Figure 1: Fuel Tank

ATTERY MAINTENANCE

Check battery fluid level daily, especially if work platform is being used in a warm, dry climate.

If electrolyte level is lower than 3/8 in. (10 mm) above plates add distilled water only. DO NOT use tap water it will shorten battery life.

Keep terminals and top of battery clean.

IRES

Tire selection can affect the stability of the machine . Use only tires supplied by UpRight (15-22.5 NHS Tubeless 16 Ply Rating) unless approved by the manufacturer in writing. Check tire air pressu re daily. (100 psi) (7 bar) (Not required for foam-filled tires).

Figure 2: Hydraulic Oil Tank

Use a ladder or platform when fueling SB80. DO NOT stand on tires when fueling the machine.



:$51,1*



Fuel cap

Hazard of explosive gas mixture. Keep sparks, flame and smoking materials away from batteries. Always wear safety glasses when working with batteries. Battery fluid is highly corrosive. Rinse away any spilled fluid thoroughly with clean water.

Do not operate machines with Plus3 option unless machine is equipped with foam filled tires. Remove machine from service and install proper tire/wheel combination before oper ating machine.



:$51,1*



:$51,1*



Hydraulic Oil Level Gau

draulic Oil Filler/ Breather Cap