Uponor Comfort-E Installation And Operation Manual
08 | 2017
Uponor Comfort-E
Thermostat Dig.
Prog Set T-86
EN INSTALLATION AND OPERATION
MANUAL
Contents
1 Copyright and disclaimer .....................................3
2 Preface ..................................................................4
2.1 Safety instructions ....................................................4
2.2 Correct disposal of this product ...............................4
3 Introduction ..........................................................5
4 Installation ...........................................................6
4.1 Installation Procedure ...............................................6
5 Operation ..............................................................7
5.1 LCD Display ..............................................................7
5.2 Turn Thermostat On/Off ..........................................7
5.3 Set the Clock ............................................................7
5.4 Temperature Display .................................................8
5.5 Set the Comfort Levels .............................................8
5.6 Lock the Thermostat .................................................9
5.7 Temperature Control ...............................................10
5.8 Temperature Hold ...................................................10
5.9 Holiday Mode .........................................................10
5.10 Frost Protection ......................................................10
5.11 Optional Features ...................................................11
6 Troubleshooting .................................................13
6.1 Error Codes .............................................................13
6.2 Re-calibrate the Thermostat ................................... 13
6.3 Factory Reset ..........................................................13
7 Technical data .....................................................14
7.1 Technical specification ............................................14
7.2 Dimensions .............................................................14
7.3 Wiring Diagram .......................................................15
2
UPONOR COMFORT-E THERMOSTAT DIG. PROG SET T-86 · INSTALLATION AND OPERATION MANUAL
EN
DK
FI
NO
SE
1 Copyright and disclaimer
Uponor has prepared this installation and operation
manual and all the content included solely for
information purposes. The contents of the manual
(including graphics, logos, icons, text, and images)
are copyrighted and protected by worldwide copyright
laws and treaty provisions. You agree to comply with
all copyright laws worldwide in your use of the manual.
Modification or use of any of the contents of the
manual for any other purpose is a violation of Uponor’s
copyright, trademark and other proprietary rights.
The presumption for the manual is that the safety
measures have been fully complied with and, further,
that Uponor Comfort-E Thermostat Dig. Prog Set T-86,
including any components that are part of such system,
covered by the manual:
• is selected, planned and installed and put into
operation by a licensed and competent planner and
installer in compliance with current (at the time
of installation) installation instructions provided
by Uponor as well as in compliance with all
applicable building and plumbing codes and other
requirements and guidelines;
• has not been (temporarily or continuously) exposed
to temperatures, pressure and/or voltages that
exceed the limits printed on the products or stated
in any instructions supplied by Uponor;
• remain in its originally installed location and is not
repaired, replaced or interfered with, without prior
written consent of Uponor;
• is connected to potable water supplies or
compatible plumbing, heating and/or cooling
products approved or specified by Uponor;
• is not connected to or used with non-Uponor
products, parts or components except for those
approved or specified by Uponor; and
• does not show evidence of tampering, mishandling,
insufficient maintenance, improper storage, neglect
or accidental damage before installation and being
put into operation.
While Uponor has made efforts to ensure that the
manual is accurate, Uponor does not guarantee or
warrant the accuracy of the information contained
herein. Uponor reserves the right to modify the
specifications and features described herein, or
discontinue manufacture of Uponor Comfort-E
Thermostat Dig. Prog Set T-86 described at any
time without prior notice or obligation. The manual
is provided “as is” without warranties of any kind,
either expressed or implied. The information should be
independently verified before using it in any manner.
To the fullest extent permissible, Uponor disclaims
all warranties, expressed or implied, including,
but not limited to, the implied warranties of
merchantability, fitness for particular purpose and
non-infringement.
This disclaimer applies to, but is not limited to, the
accuracy, reliability or correctness of the manual.
Under no circumstances shall Uponor be liable for
any indirect, special, incidental or consequential
damages or loss that result from the use of or
the inability to use the materials or information
in the manual, or any claim attributable to errors,
omission or other inaccuracies in the manual, even
if Uponor has been advised of the possibility of
such damages.
This disclaimer and any provisions in the manual
do not limit any statutory rights of consumers.
3
UPONOR COMFORT-E THERMOSTAT DIG. PROG SET T-86 ·
INSTALLATION AND OPERATION MANUAL
EN
DK
FI
NO
SE
This installation and operation manual describes how to
install and operate the components of the system.
2.1 Safety instructions
Safety measures
Conform to the following measures when installing and
operating any Uponor equipment:
• Read and follow the instructions in the installation
and operation manual.
• Installation must be performed by a competent
person in accordance with local regulations.
• It is prohibited to make changes or modifications
not specified in this manual.
• All power supply must be switched off before
starting any wiring work.
• Do not use water to clean Uponor components.
• Do not expose the Uponor components to
flammable vapours or gases.
We cannot accept any responsibility for damage
or breakdown that can result from ignoring these
instructions.
Power
Wa r ni n g!
The Uponor system uses 50 Hz, 230 V AC
power. In case of emergency, immediately
disconnect the power.
Technical constraints
Ca ut ion !
To avoid interference, keep installation/data
cables away from power cables of more than
50 V.
2.2 Correct disposal of this product
(Waste Electrical and Electronic Equipment)
NOTE!
Applicable in the European Union and other
European countries with separate collection
systems
This marking shown on the product or its
literature indicates that it should not be
disposed with other household wasted at the
end of its working life. To prevent possible harm to the
environment or human health from uncontrolled waste
disposal, please separate this from other types of wastes
and recycle it responsibly to promote the sustainable
reuse of material resources.
Household users should contact either the retailer
where they purchased this product, or their local
government office, for details of where and how they
can take this item for environmentally safe recycling.
Business users should contact their supplier and check
the terms and conditions of the purchase contract. This
product should not be mixed with other commercial
wastes of disposal.
2 Preface
4
UPONOR COMFORT-E THERMOSTAT DIG. PROG SET T-86 · INSTALLATION AND OPERATION MANUAL
EN
DK
FI
NO
SE
3 Introduction
A programmable room thermostat is both a programmer
and a room thermostat.
A programmer allows you to set “On” and “Off” periods
to suit your own lifestyle. A room thermostat works by
sensing the air temperature, switching on the heating
when the air temperature falls below the thermostat
setting, and switching it off once this set temperature
has been reached.
So a programmable room thermostat lets you choose
what times you want the heating to be on, and what
temperature it should reach while it is on. It will allow
you to select different temperatures in your home at
different times of the day (and days of the week) to
meet your particular needs and preferences.
Setting a programmable room thermostat to a higher
temperature will not make the room heat up any faster.
How quickly the room heats up depends on the design
and size of the floor heating system.
Similarly reducing the temperature setting does not
affect how quickly the room cools down. Setting a
programmable room thermostat to a lower temperature
will result in the room being controlled at a lower
temperature, and saves energy.
The way to set and use your programmable room
thermostat is to find the lowest temperature settings
that you are comfortable with at the different times you
have chosen, and then leave it alone to do its job.
The best way to do this is to set the room thermostat
to a low temperature – say 18°C, and then turn it up
by 1°C each day until you are comfortable with the
temperature. You won’t have to adjust the thermostat
further. Any adjustment above this setting will waste
energy and cost you more money.
You are able to temporarily adjust the heating program
by overriding or using the temperature hold feature.
Programmable room thermostats need a free flow of air
to sense the temperature, so they must not be covered
by curtains or blocked by furniture. Nearby electric fires,
televisions, wall or table lamps may also prevent the
thermostat from working properly.
5
UPONOR COMFORT-E THERMOSTAT DIG. PROG SET T-86 ·
INSTALLATION AND OPERATION MANUAL
EN
DK
FI
NO
SE
4.1 Installation Procedure
Do
Mount the thermostat at eye level.
Don’t
Do not install near to a direct heat source
as this will affect functionality. Do not
push hard on the LCD screen as this may
cause irreparable damage.
This thermostat is designed to be flush mounted and
requires a back box of 35mm (minimum depth) to be
sunk into the wall prior to installation.
To install the thermostat, follow these steps:
1. Separate the front half of the thermostat from the
back plate by placing a small flat head terminal
driver into the slots on the bottom face of the
thermostat.
2. Place the thermostat front somewhere safe.
3. Connect the thermostat.
For more information, see section “7.3 Wiring
Diagram” on page 18.
4. Screw the thermostat back plate into the back box.
5. Clip the front of the thermostat back onto the
thermostat back plate.
4 Installation
6
UPONOR COMFORT-E THERMOSTAT DIG. PROG SET T-86 · INSTALLATION AND OPERATION MANUAL
EN
DK
FI
NO
SE
Loading...