U Pass CPR 303US Users manual
U Pass co., Ltd
Content
CONTENT....................................................................................................................................2
Caution .......................................................................................................................................3
CHAPTER 1. INTRODUCTION ..................................................................................................4
1.1 Reader Define
1.2 Operation Specifications
1.3 Communication Specifications
1.4 Enviroment Specifications
1.5 hGz
1.6 Reader Specifications
1.7 Product Image
CHAPTER 2. HARDWARE INSTALLATION
2.1 Each partial by summary of hardware
CHATER 3. READER THEORY OF OPERATION
3.1 Blockdiagram
3.2 Reader Theory Of Operation
CHATER 4. USER MANUAL
4.1 Bootloader Connectivity
4.2 Bootloader Manual
4.3 Pin Assign
4.3.1 power
4.3.2 RS -232
4.3.3 Relay
4.3.4 Loop Detector
CHAPTER 5. Contact
CAUTION...
- Use a power cable rated for the voltage in question.
- Be sure however to use a power cable conforming to safety standard of your nation
when using a product overseas.
- Do not place anything heavy on top of the power cable.
- Before turning on the power, be sure to check that the supply voltage matches
the voltage requirements of the instrument.
- Use a power have suitable specifications.
- Use a power plug normally.
- Handle a power adaptor as follows.
a. Remove a dust or foreign body of the surface before plug in.
b. Insert a power plug completely.
c. Do not use a loose power plug.
d. Do not drag a power cable when pull out a power plug.
This can cause a cable short or a fire.
e. Pull out a cable in a dried hand. In case of touching by a wet hand,
an electric shock can be occurred.
- Turn off the power before connecting of a communication cable or
some peripheral devices.This can cause an electric shock.
- Do not the heavy things on the reader to reduce the risk of body injury
when the reader clash to the floor.
- When a strange smoke,small or abnormal temperature occure,stop the reader operating.
a. This is the major cause of an electric shock or a fire.
b. Remove a power cable.
c. Do not disassemble the reader.
- Do not disassemble or convert the reader for repair.
- This can cause hurts,an electric shock or a fire.
- Check the connecting of a antenna port, when the state of tagging is not good.
- Set a reader at the stable place. The vibration can cause to make a fault reader
by falling or damaging.
Chapter 1. Introduction
1.1 Reader Define
The CPR-303US is high performance RFID reader that reliably operated in
outdoor circumstances.
The I/O structure of the CPR-303US enables inputting sensor signal and
outputting controller. With internal antenna and simple construction,
CPR-303US provides a seal against adverse environmental conditions.
It is designed based on ISO18000-6 so that it supports major tag protocols.
The CPR-303US can be operated not only in stand-alone mode but also
in remote control mode by adjusting internal selection switch which enables wide
application range.
The most suitable application range of this reader is parking-lot application,
vehicle and human access control.
1.2 Operation Specifications
- ISO18000 6A, 6B, 6C singular which is satisfied a standard or it will recognize
multiple Tag and there is a possibility which it will write a data in Tag memories.
- External Interface support : RS -232, TCP/IP
- To use LED, the operation state identification is possible from the external.
- User Mode Possibility.
- Firmware upgradable by Bootloader
1.3 Communication Specifications
External
Serial 9600bps / 38,400bps / 115,200bps
Interface
Ethernet TCP/IP
Air Protocol
1.4 Enviroment Specifications
Operating Temp.
Storage Temp.
Humidity
Tag Air Protocol
ISO 18000 - 6A
ISO 18000 - 6B
ISO 18000 - 6C
-30˚C ~ 40˚C
-30˚C ~ 70˚C
10% ~ 95%
Loading...