How it Works
UP3D
Loading...
A
U
Loading...
Loading...
UP500
User Manual
65 pgs3.14 Mb0

UP3D UP500, UP300, ACUBLU User Manual

UP3D TECH CO.,LTD
1
UP3D DENTAL SYSTEM
User Manual
UP3D TECH CO.,LTD
2
Contents
Ⅰ.Installation of UP3D DentalSystem................................................................................................ 5
1.2.1 Check the scanner and accessories
.........................................................................................
6
1.2.2 Scanner Connection.................................................................................................................9
1.3 Installation of Software
.............................................................................................................
9
1.4 Device Diagnostics
.................................................................................................................
10
1.5 Calibration.............................................................................................................................. 12
1.5.1 Step of calibration................................................................................................................ 12
Ⅱ
.UPDentalManager.......................................................................................................................................16
2.1 Main interface......................................................................................................................... 16
2.2 Order Management
.................................................................................................................
18
2.3 UPDentalManager Configuration..........................................................................................23
2.3.1 General setting
......................................................................................................................
23
2.3.2 UPCAD Configuration........................................................................................................ 24
2.3.3 UPSCAN Configuration
.....................................................................................................
26
2.3.4 Manage Users.......................................................................................................................28
Ⅲ.Authorization Management.........................................................................................................................30
Ⅳ.Model Scanning
..........................................................................................................................................
31
4.1 Types of dental scanners
.........................................................................................................
31
4.2 Use of accessories...................................................................................................................32
4.2.1 Die scan
...............................................................................................................................
32
4.2.2 Gypsum scan........................................................................................................................ 32
Side-lay articulator scan.................................................................................................................32
4.2.3 Impression scan
....................................................................................................................
33
4.2.4 Implant scan body scanning.................................................................................................33
4.2.5 Wax-up scanning
.................................................................................................................
34
4.3 Main interface.........................................................................................................................35
4.3.1 Application panel................................................................................................................. 35
4.3.2 Tools
....................................................................................................................................
37
4.3.3 Camera panel.......................................................................................................................45
4.4 Scanning step
...........................................................................................................................
46
4.4.1 Multi-dies scanning............................................................................................................. 46
4.4.2 Model scanning
...................................................................................................................
47
4.4.3 Impression scan................................................................................................................... 54
UP3D TECH CO.,LTD
3
4.4.4 Implant scan body scanning
................................................................................................
57
4.4.5 Wax-up scanning................................................................................................................. 58
4.4.6 Freedom scan
.......................................................................................................................
61
Ⅴ.Appendix
.....................................................................................................................................................
62
5.1 5.1 Mouse and shortcut key operation....................................................................................62
5.1.1 Mouse operation....................................................................................................................62
5.1.2 5.1.2 Shortcut keys operation
..............................................................................................
62
5.2 UPSCAN scanning software................................................................................................... 63
5.2.1 5.2.1 In cloud point or mesh edit mode............................................................................... 63
5.2.2 Shortcut keys in impression scanning
..................................................................................
64
5.2.3 Impression margin line edit function (UP300).................................................................... 64
5.3 Frequently used shortcut keys of UPCAD
..............................................................................
64
5.3.1 Connector............................................................................................................................. 64
5.3.2 Morphing function............................................................................................................... 64
UP3D TECH CO.,LTD
4
Product Introduction
UP3D focuses on the development and manufacture of dental model scanner, CAD/CAM dental restoration software. At present, the main products are: high precision blue light model
scanners, dental design software UPCAD, dental computer-aided manufacture software UPCAM.
ACUBLU
UP300
UP500
UPSCAN
UPCAD
UPCAM
UP3D TECH CO.,LTD
5
Ⅰ.Installation of UP3D DentalSystem
1.1
Hardware Configuration
To have a better experience, please configure your computer as recommended.
Item
Recommended
Windows system
Windows7/10,64 bit professional, Win10 is recommended
CPU
Intel Core i7 or above (or other same level CPU)
Graphics card
NVIDIA, 4G or above
Memory
8GB/16GB or above
Hard disc
Double hard disc: SSD 120G + 1TB HDD(7200R)
Main board
Please select a well-known manufacturer's main board (such as asus), include the USB 3.0 port
1）Check if it contains standalone graphics；
2）Check if the USB port is sufficient
；
3 ） For better stability,it is recommended to use the brand computer, not the
assembly computer
；
UP3D TECH CO.,LTD
6
1.2 Installation of Hardware
1.2.1 Check the scanner and accessories
Accessories
Quantity
Picture
Compatible scanners
USB cable
1
All scanners
Power cable
1
All scanners
PCI-E card
1
AcuBlu
The computer must have sufficient PCI interface
Blue Tack
1
All scanners
UP3D TECH CO.,LTD
7
Shade cloth
1
All scanners
Calibration board
1
Stone calibration board
All scanners
Plate
1
Screw retained plate
All scanners
1
Regular plate
All scanners
Die plate
1
6-hole-die plate
UP200
AcuBlu
UP3D TECH CO.,LTD
8
1
12-hole-die plate
UP300
Impression
fixtures
1
UP300
Dongle
1
All scanners
User Manual
1
All scanners
Figure 1-1
UP3D TECH CO.,LTD
9
1.2.2 Scanner Connection
（1）Connect USB cable of scanner to the computer's USB port；
（2）
Connect the power line to the power port of scanner
；
（3）Insert the UP3D dongle ;
（4）
Power on the scanner
；
Figure 1-2 Figure 1-3
1
）
The connection requires a ground wire to avoid damaging the internal
components of the scanner！
2）Please unplug the scanner when it’s thunderstorms!
1.3 Installation of Software
Installation steps vary depending on the hardware version of the scanner!
UP3D TECH CO.,LTD
10
（1）
Download SCAN/CAD/CAM software package on the http://www.up3d.cn
Software Package: UP3D DentalSystem 2018-version number.exe
DentalManager、CAD、Viewer、DongleManager etc.
Software Package: UP3D Scanner 2018-version number.exe
Include: UPSCAN
（2）
Double-click the setup, and the language selection dialog box pops up. Select the installation
language
UP3D DentalSystem support multiple languages：Chinese, English, Russian, Korean, Italian,
Bulgarian, Turkish etc.
（3）
Click the ok button to enter the installation guide
（4）Click next, select the installation location. The default location is C:\UP3D...（Make sure
there is enough free space to install）
（5）Click next, check the part you want to install, which defaults to full selection.
（6）
Click next, add shortcut.
（7）Click next, create a desktop icon.
（8）
Click install and start the installation.
（9）finish the installation.
After the installation, the shortcut of UP3D DentalSystem and relative software would be created on the desktop
1.4 Device Diagnostics
Used to diagnose working status of scanner and components
Diagnostic Method
：
（1）connect the scanner, and turn on the scanner.
（2）
Below the start menu-->UP3D-->Scanner, click the device diagnostics, enter the diagnostic
interface. There are two methods:
One key detection: check if all components drivers and connection is normal
UP3D TECH CO.,LTD
11
（
figure 1-4）.
Manual detection: expert detection mode, check the status and parameters of all
components drivers and connection（figure 1-5）.
Figure 1-4
Figure 1-5
UP3D TECH CO.,LTD
12
1.5 Calibration
Calibration will affect accuracy. Calibration is generally required in the following situations:
The first use of scanner; or use again after long period of time.
After opening the calibration software for the first time or starting the scan through the dental manager, the hint window (figure 1-6) will pop up. Click re-calibration.
（2）When starting calibration for the first time, if the software detects that the camera needs to
initialize, then a dialog box (figure 1-7) will pop up and click the "ok" button. The software will automatically adjust the camera and enter the calibration interface again
When the scanner is used again after transportation.
When there is rough surface or abnormal data quality in the scanning process
Figure 1-6
Figure 1-7
1.5.1 Step of calibration
（1）Double-click the ‘UP3D Scan Calibration’ shortcut or click the Calibrate scanner button at
the dental manager interface to start the Calibration function.
（2）insert the calibration board and use the shading cloth. Click ‘start’ (figure 1-8) to enter the
calibration interface
UP3D TECH CO.,LTD
13
Figure 1-8 Calibration startup interface
（3）
Enter calibration interface（figure1-9
）
Figure 1-9 calibration interface
Adjust the appropriate gain value and exposure time
UP3D TECH CO.,LTD
14
Select one of the calibration methods to calibrate, please select AF (automatic calibration),
MF (manual calibration) is generally used in expert mode.
（4）
Select automatic calibration method：click【AF】to start calibrate
【AF】automatic calibration: calibrate automatically
After click AF, the scanner starts to calibrate automatically (figure 1-10). In this process,
the calibration progress bar will be displayed at the bottom of the interface. Please wait for the camera to automatically complete the 13-step image acquisition and processing, after shows
‘
calibration successful’, click‘ok’(figure 1-11), and exit the calibration
Figure 1-10 AF interface
Figure 1-11 AF interface
（5）Select manual calibration method
Manual calibration is generally used in expert mode, where users could check the image
acquisition status of each step and display the calibration precision after the calibration is completed
【MF】manual calibration:
Click MF to enter the manual calibration interface, and click【next】button to perform the
acquisition. After 13 steps, the camera image acquisition is completed, the pop-up dialog box shows
the camera calibration and axis calibration results (figure 1-12) and click the OK button to complete
the calibration
UP3D TECH CO.,LTD
15
Figure1-12 The interface of manual calibration finishing
【Recollection】：when the image acquisition failed, left click “recollection” or “F5”
to recollect. Please adjust the gain value and exposure time manually when recollect.
UP3D TECH CO.,LTD
16
Ⅱ.UPDentalManager
UPDentalManager, mainly provides the new order creating and management, order query and other functions
2.1 Main interface
Figure 2-1
The main interface consists of the following parts(Figure 2-1)
：
1.Menu bar
2.Order query
3.Order list
4.Design information
5.Prompt bar
The menu bar includes the following functions
New order button: Build the new order
Fuzzy search: Used to search for orders, searching for orders containing the specified text information in order No., name, and memo.
System setting: set the parameters of UPDentalSystem, CAD/SCAN etc.
UP3D TECH CO.,LTD
17
Dongle management: check and update the dongle license
Calibrate the scanner: start the calibration
（2）Order query
Search the orders from yesterday or this week
Advanced Search:(figure 2-2), searched by date range or by customer
Figure 2-2
(3) Order list
Display the queried order list. The basic information of every order could be checked here
directly, such as: ID number, name, date, design type, status etc.
Operation：
UP3D TECH CO.,LTD
18
Single click：click on the order management list to displayed the tooth number and design
type of current order, also could view the model in real time at the information area (right bottom corner)
Right click：select the order and right click or right click at the blank area, pops up the menu
as figure2-3.
Figure 2-3
（4）
Design information
Tooth diagram：display the tooth number or design type of current order on the tooth diagram
Model viewer: preview the scan model and design model of current order
（5）Prompt
Dongle license information: display the dongle license information, click to start the dongle
management;
User: display the current user information, click to start the user management;
2.2 Order Management
(1) 3 ways to create a new order
Click“create”icon
Right click and select“Create a new order
”
Keyboard shortcut: Ctrl+ N
Edit orders: modify order information.
UP3D TECH CO.,LTD
19
When editing an order, please pay attention to the following:
1）Do not modify“model source”.
2）After saving modifiction,it will be prompted ‘re-scan’or ‘import order?’
The key information includes: add or delete tooth, modify design type, teeth design parameters, scan settings.
(2) View the order: check the details of the order. (3) Delete Order: delete the specified order from the order library. When deleting the order, it will
pop up “Delete completely” or “Keep the data”.
Delete completely: completely remove the order from the order library and delete the model
file stored on the disk.
Keep the data：orders are only deleted from the order library, but the model files on the disk
are still kept.
(4) Rest order: change order status
Reset to design: The order that have been designed or milled, revert to the state when the scan
was completed , remodeling
Reset to create: an order that has been scanned, designed, or processed, reverted to the state
when the creation was completed, and rescanned;
(5) Open local file: Open the directory where the order is located.The folder contains scanned data
and design data.
(6) Order import and export
Export Order: Export order information and order model file to “uorder2 file” in the order
library. You can back up any orders you want. Uoder2 file can be imported into UPDentalManager by “Import Order” function.
Import Order : import “uorder2” order into UPDentalManager.
Export exocad project : UP3D order can be exported to exocad project files so you can import
to Exocad for design easily
(7) Reset the checkout source: as long as the data source computer user name is changed when the
order is checked out, in order to avoid the data source computer name does not match the computer IP, so it needs to be resetted the checkout source. But resetting the checkout source is only for the current order.
UP3D TECH CO.,LTD
20
(8) Delete selected order temporary data: Delete the temporary scanned data.
(10) Order Search
Fuzzy search: in the search box of the menu bar, input directly content that you want to search and click “Enter”. The search range can be selected from the fuzzy search options in the advanced menu of the search area, including the order number, Memo, and Name.
Quick Search: click ‘yesterday’ or ‘This week’ icons. All orders for yesterday or this week are
displayed in the order list.
Advanced Search:
According to date —— After selecting the date range, click “search” icon; All orders during the date range will be displayed in the order list.
According to precise time: If you select ‘today’ in the drop down list, click “search” icon; All orders for today are displayed in the order list.
Figure 2-4
According to status: mouse moving over the status column title bar of the order, select ‘unscanned’, ‘scanned’ or ‘designed’ in the pop-up window to display all orders currently selected.
Loading...
+ 45 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use