UNO LASER X-LRGB 1W ILDA User Manual

Download

1 | BERMUDA X-LRGB1W ILDA USER MANUAL V2016-A

X-LRGB 1W ILDA

LASER LIGHT FIXTURE – CLASS 4

LASER LIGHT

AVOID EYE OR SKIN EXPOSURE TO DIRECT OR SCATTERED LIGHT

CLASS 4 LASER PRODUCT

CLASSIFIED PER EN/IEC 60825-1 2007

UNO LASERS FIXTURES ARE APPROVED FOR SAFE USE IN USA!

THIS DEVICE COMPLIES WITH PERFORMANCE STANDARS FOR LASER

PRODUCTS UNDER 21 CFR 1040 EXCEPT

WITH RESPECT TO THOSE CHARACTERISTICS AUTHORIZED BY

VARIANCE NUMBER: “2013-V-0607”

2 | BERMUDA X-LRGB1W ILDA USER MANUAL V2016-A

USER INFORMATION

This manual contains important laser operation information. Read and understand all instructions prior to powering on laser unit the first time, to avoid laser eye injury and to avoid breaking the law. Keep this manual in a safe place for future reference.

WARNING DATA

Lasers can be hazardous and have unique safety considerations. Permanent eye injury and blindness is possible if lasers are used incorrectly. Pay close attention to each safety REMARK and WARNING statement in the user manual. Read all instructions carefully BEFORE operating this device.

NON-INTERLOCKED HOUSING WARNING

This unit contains high power lasers internally. Do not open the laser housing, due to potential exposure to unsafe levels of laser radiation. The laser power levels accessible if the unit is open can cause instant blindness, burn skin, and cause fires.

VARIANCE

A "Laser Light Show Variance" is the permit required from FDA for operating UNO Lasers in a public forum & outlined in details under FDA guidelines for Laser Display Show. If you are producing a show with laser light effects, not having a show variance could lead to large fines if your show gets inspected by FDA officials.

Demonstration laser products are only to be purchased and used by organizations which already hold a valid Class 3B or Class 4 US laser light show variance!

Visit our website to apply for your FREE Laser show variance

http://variance.ProXdirect.com

WARRANTY 1 Year Laser Diods & Scanner 2 Years General Parts Life Time Clean & Calibrate Each Uno Laser system will be cleaned and re-

calibrated at no extra cost each year for the life of the unit. (Shipping not included)

Please register your new purchase with us for your warranty with Uno Laser within 30 days of your purchase.

http://warranty.ProXdirect.com

3 | BERMUDA X-LRGB1W ILDA USER MANUAL V2016-A

SAFETY NOTES_

LASER RADIATION WARNING / SAFETY

 Please note there is high potential for eye and skin injury if

strict adherence to these guidelines is not followed.

 These Class 3B and Class 4 demonstration laser products are

only to be purchased and used by organizations which already hold a valid Class 3B or Class 4 US laser light show variance.

 Do not point laser or allow laser light to be directed or reflected

toward other people or reflect objects.

 Laser is never to be operated if the unit is defective or the

cover or seal is damaged.

 Direct or scattered light can be hazards to eyes and skin.  INDOOR USE ONLY. Outdoor laser shows require prior FAA

written approval.

USER ACCESSIBILITY / MAINTAINANCE

 Do not modify the unit or remove protective covers or housing.  No scheduled maintenance is necessary to keep this product in

compliance.

 Unit must be returned to factory for any required service or

repair.

 Service is only to be handled by authorized factory trained

technicians. There are no user serviceable parts, etc.

4 | BERMUDA X-LRGB1W ILDA USER MANUAL V2016-A

Unpacking Instructions

CAUTION!

Immediately upon receiving a fixture, carefully unpack the

carton, check the contents to ensure that all parts are present,

and have been received in good condition. Notify the shipper

immediately and retain packing material for inspection if any

parts appear damage from shipping or the package itself shows

signs of mishandling. Save the package and all packing materials.

In the event that a fixture must be returned to the factor, it is

important that the fixture be returned in the original factory box

packing.

What is included?

The carton or flight case contain following items:

Name

QTY

BERMUDA 1W RGB TTL Laser Light Fixture

1PCS

KEYs (for key switch)

2 PCS

6FT Power Cord (Edison to PowerConn)

1 PCS

E-Stop Switch w/ Keys

w/30ft cable

1 PCS

USER MANUAL

1 PCS

5 | BERMUDA X-LRGB1W ILDA USER MANUAL V2016-A

Power Supply

To determine the power requirements for a particular fixture, see the label affixed to the back plate of the fixture of refer to the fixture’s

specifications chart. A fixture’s listed current rating is its average current

draw under normal conditions.

All fixtures must be powered directly off a switched circuit and cannot be run off a rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer channel is used solely for a 0% to 100% switch. Before applying power to a fixture, check that the source voltage matches the fixture’s requirement.

LASER INFORMATION

This Laser Product is designated as Class 4

during all procedures of operation.

LASER EMISSION DATA

Laser Classification

Class 4

Green Laser

LD 532nm

Red Laser

LD 635nm

Blue Laser

LD 445nm

Beam Diameter

<5mm at aperture

Divergence(each beam)

<2 mrad

Divergence(total light)

<90 degrees

Transverse Beam Mode

TEM00

Cooling

TEC & Fan Cooling

Scanning

DC to 20KHz, ±30 Degrees X & Y

*As measured under IEC measurement conditions for classification.

IMPORTANT

6 | BERMUDA X-LRGB1W ILDA USER MANUAL V2016-A

LASER INFORMATION

Laser Power:

Total 1100mw Beam Divergency Diameter(mm) Red 250mw 635nm < 3.5x0.5 mrad < 2x5mm Green 150mw 532nm < 1.5 mrad < 3mm Blue 700mw 445nm < 2x0.5 mrad < 2x5mm

Scanner: 25kpps@8° High Speed Optical Scanner Scan Angle max.: 60° X/Y Axis Beam Angle: ±30

SPECIFICATIONS

Main Input: AC100240V, 50/60Hz Fuse: 250V 2A Slow Blow (20mm Glass) Power Consumption: 45W Control Mode: Auto, Sound, DMX, Master / Slave, ILDA

Laser Safety eyewear and NOHD distance.

Class 4 Safety Data NOHD = 300 meters Safety Eyewear OD (optical density.. Attenutation) = <3.5

Laser Classification: Class 4 Laser Safety Standard: EN/IEC 60825-1 2007 Condition Temperature: 10 400C DMX Connections: 3 pins XLR Male/Female DMX Channels: 12 channels Measurement: L=32cm, W=26cm, H=26cm N Weight: 6Kg / 13lbs

All information provided is subject to change without notice.

7 | BERMUDA X-LRGB1W ILDA USER MANUAL V2016-A

LABEL REPRODUCTION

Safety Label location

As FDA/CDRH required under Laser Compliance Regulations,

here you will find a diagram that outlines the radiation warning labels

and where you will find them located on the unit itself.

8 | BERMUDA X-LRGB1W ILDA USER MANUAL V2016-A

PROPER USE/MINIMUM HEIGHTAUTIN!

CAUTION! - USE OF CONTROLS OR ADJUSTMENTS, OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

This product is for overhead mounting only.

For safety purposes, ProX and Xstatic Pro Lighting recommend mounting lighting effect products on steady elevated platforms or sturdy overhead using suitable hanging clamps. In all cases, use safety cables.

Obtain appropriate mounting hardware from your lighting vendor.

International laser safety regulations require that laser products must be operated in the fashion illustrated below, with a minimum of 3 meters (9.8 ft) of vertical separation between the floor and the lowest laser light. Additionally, 3 meters of horizontal separation is required between laser light and audience or other public spaces.

LASER VARIANCE

LASER VARIANCE REQUIREMENT!

These Class 3B and Class 4 demonstration laser Products are only to be purchased and used by organizations which already hold a valid Class 3B or Class 4 US laser light show variance

Visit our website to apply for your FREE Laser show variance

http://variance.ProXdirect.com

Do not point laser or allow laser light to be directed or reflected toward other people or reflective objects.

Minimum height requirement: 3 meters, or 10 feet in clearance

3 meters

9 | BERMUDA X-LRGB1W ILDA USER MANUAL V2016-A

The unit is supplied with a power plug appropriate to its voltage and destination. Should any other connections be required they must be carried out with the following configuration.

Cable (EU)

Cable(US)

International

Brown

Black

Live

Light blue

White

Neutral

Yellow/Green

Green

Earth

Proper Laser Set Up & Usage

 This fixture has been designed to be hung. It is recommended for safety purposes, your lighting

effect are properly mounted using a suitable hanging clamp and make sure the area below

the installation place is free unwanted persons during rigging, de-rigging and servicing.

 The operator has to make sure that safety-relating and machine-technical

installations are approved by an expert before taking into operation for the first time and after changes before taking into operation another time.

 The operator has to make sure that safety-relating and machine-technical

installations are approved by a skilled persons cannot reach

 The fixture should be installed in the position where persons cannot reach and

where persons may walk by or be seated.

PRODUCT OVERVIEW

This device has left our premises in absolutely perfect condition. In order to maintain this condition and to ensure safe operation, it is necessary for the user to follow the safety instructions and warning notes written in this manual.

The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual or any unauthorized modification to the device.

FUSE 5mmx20mm FFUSEF 1 A/250V

CAUTION! When installing the device, make sure there is no highly - inflammable material (decoration articles, etc.) within a distance of min. 0.5m / 20inches

10 | BERMUDA X-LRGB1W ILDA USER MANUAL V2016-A

Front Panel

NAME

FUNCTION

Emission Indicator

Laser emission LED indicator

MIC Sync LED

Synchronize to detected music signal.

“DMX On” LED

Indicates DMX Signal is Active.

APERTURE

Laser output aperture

Beam Block

Sliding laser beam block used for audience safety

11 | BERMUDA X-LRGB1W ILDA USER MANUAL V2016-A

Rear Panel

NAME

FUNCTION

Rear DMX Sync LED

Indicates DMX Signal is Active.

Rear MIC Sync LED

Synchronize to detected music signal.

Rear “Power On” LED

Laser emission LED indicator

X Y invert

Invert X or Y axis/pattern size zoom control

Sound Sense Adjust

Attenuates the Sensitivity to Music

Safety Eye

Safety Cable attachment mount

MIC, Microphone

Ambient Audio Input for Music Sync

Remote Interlock Port

Attaches Emergency Stop box.

Key Switch

Switches on and Off the Diode Emissions

Laser Control Panel

Intelligent LED control panel of the system

DMX Linking

XLR-3PIN Ports, for DMX in/out

Fan

ventilation fan

ILDA Interface In/Out

ILDA interface for software

Main Power Switch

On/Off Switch, Main Power Source.

Fuse

2A Fuse

Mains input

Main powercon socket

Ground Pin

Ground screw

12 | BERMUDA X-LRGB1W ILDA USER MANUAL V2016-A

LCD FUNCTION SETTING

Press “UP” or “DOWN” to choose function in the same menu.

Press “ENTER” button to enter next menu.

Press “RETURN” button to return previous menu.

Menu operating instruction

When you turn on the laser for the first time, it will take some seconds to auto load the built-in show

The default setting is AUTO EFFECT 1.

First Menu

Second Menu

Third Menu

Fourth Menu

DMX512

Running A001 (DMX address)

AUTO (auto running mode)

Running Effect 1 (Full show) Effect 2 (only beam) Effect 3 (only cartoon)

Music (sound activate mode)

Running Effect 1 (Full show) Effect 2 (only beam) Effect 3 (only cartoon)

Setting

Address

Choose DMX address

Light (LCD backlight setting)

OFF ON ON 5S (ON for 5 seconds) ON 10S (ON for 10 seconds)

Cartoon (Running speed)

Press UP and down to choose running speed from 1 99, 99 is the fastest

Master (set master unit)

OFF ON

LASER (size and color setting

Size

(press up or down to choose the size of graphics

Color

1. Single color

(7 colors)

2. RGY

3. GBC

4. RBP

5. RGB

Default (Restore default setting)

Yes NO

ENTER

RETURN

DOWN

DMX-512 Auto

13 | BERMUDA X-LRGB1W ILDA USER MANUAL V2016-A

DMX-512 connection between fixtures

The fixture is equipped with 2-pin XLR sockets for DMX input and output. The sockets are wired in parallel. Only use a shielded twisted-pair cable designed for 3-pin XLR-plugs and connectors in order to connect the controller with the fixture or one fixture with another.

Occupation of the XLR-connection

DMX – output DMX - output

XLR mounting-sockets (rear view): XLR mounting-plugs (rear view):

Caution: At the laser fixture, the DMX-cable has to terminate with a terminator.

Contact your dealer to purchase ProX Cables DMX Terminator.

SKU: XC-DMX3PTR

Building a serial DMX-chain (DMX Mode)

 If you are using the standard DMX-controllers, you can connect the DMX-output of the controller

directly with the DMX-input of the first fixture in the DMX-chain.

 Connect the DMX-output of the first fixture in the DMX-chain with the DMX-input of the next

fixture. Always connect output with the input of the next fixture until all fixtures are connected.

 If you use a controller with 5 pins DMX connector, you need to use a 5 to 3 pins adapter  Connect the fixture together in a daisy chain by DMX XLR plug cable from the output of the fixture

to the input of the next fixture. The cable cannot be branched or split to a Y cable. DMX 512 is a

very high speed signal. Inadequate or damaged cables, soldered joints or corroded connectors

can easily distort signal and shut down the system.

 Each fixture needs to have a DMX address to receive the data from the controller. The DMX

address number which could be read from rear panel of each fixture is between 001-512

 The end of the DMX 512 chain should be terminated to reduce signal errors.

14 | BERMUDA X-LRGB1W ILDA USER MANUAL V2016-A

Instruction for DMX channels

CH1

LASER OFF

041

LASER OFF

Auto Activate 4283

DMX mode, CH2CH12 valid

84125

Built-in cartoon graphics auto running mode

126167

Built-in beam graphics auto running mode

Sound Activate 168209

Built-in beam graphics auto running mode

210251

Built-in cartoon graphics auto running mode

252255

DMX mode, CH2CH12 valid

CH2

Pattern select

0255

Selecting built-in patterns

CH3

Rotation 0127

Manual rotation

128191

Auto counter-clockwise rotation (from slow of fast)

192255

Auto clockwise rotation (from slow to fast)

CH4

X axis rolling 0127

Manual rolling

128255

Auto rolling (from slow to fast)

CH5

Y axis rolling 0127

Manual rolling

128255

Auto rolling (from slow to fast)

CH6

X axis moving 0127

Manual choose moving position

128255

Auto moving (from slow to fast)

CH7

Y axis moving

0~127

Manual choose moving position

128~125

Auto moving (From slow to fast)

CH8

Pattern size

0~63

Choose pattern size, 0 is normal size, 1 is the smallest, 63 is

the biggest

Zooming

64~127

Auto zooming (-) from slow to fast

128~191

Auto zooming (+) from slow to fast

192~255

Manual zooming (+/-) from slow to fast

CH9

Drawing

0~255

Auto drawing from slow to fast

CH10

Scanning speed

0~127

Choose scanning speed from slow to fast

Display dot

128~255

Choose the length of dot

CH11

Color setting

0~24

Normal color

25~199

Choose every single color

200~224

Every single color changing one by one

225~255

All the colors together changing alternatively in

pattern

CH12

Color change

speed

0~255

Adjust color changing speed from slow to fast

15 | BERMUDA X-LRGB1W ILDA USER MANUAL V2016-A

TROUBLE SHOOTING

1. If the power indicator is off the laser doesn’t work, please check the Power

Cord, fuse and power supply.

2. In Stand-Alone operation, if the power supply indicator is ON and sound

active indicator is OFF, but the laser doesn’t work.

 The sound may be too small and cannot activate the laser running,

please increase the music volume or increase sound sensitivity on rear panel.

 Please check if unit has been set up in slave mode, or DMX mode.

3. In Master-Slave operation, if slave fixtures don’t run;  Make sure there’s only one master in the chain, and the others are

set in Slave mode.

 Make sure to use a good quality DMX and Power Cables to run the

chain.

4. In DMX operation, if the unit can’t be controlled by the DMX console, but

the DMX signal indicator on the item is flashing, Please make sure the DMX console and fixture have the same channel.

After trying the above solution you still cannot sort out the problem, please contact your Dealer or UNO LASER for service.

1. Please use this device only according to these operating instructions.

2. Do not use the device if there are any visible damages on housing, connector panels, power supplies or power cords.

3. Never look directly into the light source of a laser projector. Danger of damage to the eyes or even blindness in extreme circumstances!

4. Do not operate the device at high humidity, in the rain or in dusty environments.

5. Protect device against dripping or splashing water. Do not place any liquid filled containers near to this device.

Any warranty claims are void if the warranty label is removed or tampered with in any way.

All information provided in this manual is subject to change without notice.

16 | BERMUDA X-LRGB1W ILDA USER MANUAL V2016-A

Please register your new purchase with us for your warranty with

Uno Laser within 30 days of your purchase.

http://warranty.ProXdirect.com

Our Products and You

Year after year, we are continuously blown away by the amazing productions we see happening around the world with ProX Gear! We especially want to thank all our dealers, and all our seriously talented customers who choose ProX, for your support and creativity! Be sure to tag us on social media like Facebook and Instagram, or send us your best images of you and your favorite ProX Gear to our website! THANK YOU!

#unolaser

facebook.com/unolaserusa

UNO Laser

25 Colgate Rd Great Neck NY

Tel: 718-237-2299

www.unolaser.com unolaser@gmail.com

UNO LASER X-LRGB 1W ILDA User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual