Univex PM91G Specifications

PM91

PM91

NOW EQUIPPED WITH A 1 H.P. MOTOR!

April 2005

Printed in USA

PREP MATE

UNIVEX CORPORATION ■3 Old Rockingham Road ■Salem, NH 03079-2140

Tel [phone] ■Fax [phone] ■E-mail [e-mail]

TOLL-FREE ORDERING FAX [phone]

www.univexcorp.com

Our main ingredient is value

SINCE 1948

WARRANTY

The Prep-Mate PM91 carries a one-year, on-site parts and labor warranty against any flaws in materials and workmanship. This period begins with the date of purchase and, provided
the unit is used properly in accordance with our instructions, is in full effect for one year from that date. Any work to be performed under this warranty must be performed between
the hours of 8:00 a.m. and 5:00 p.m. local time, Monday through Friday. Univex will not pay overtime charges for work performed other than during normal business hours. Damages
incurred in transit or from installation error, accident, alteration or misuse are not covered.Transit damages should be reported to the carrier immediately. Univex shall not be liable
for any consequential, compensatory, incidental, or special damages. Contact Univex Service Department for any warranty claims.

Designed for heavy duty use, the Prep­mate* does not bog down even on the
toughest loads. Driven by a 1 HP motor
with a 1" wide Pol-V belt system, our
Prep-Mate is a tough but quiet kitchen
performer. A 5" deep prep container with
cover comes standard with this unit. a
vegetable slicer for cutting, a VS9H for
shredding, and/or a meat & food chopper
attachment can be used on this maximum
price/value for years of trouble free per­formance. This unit is UL listed and NSF
approved.

*The prep-Mate is a power drive

unit only. see back for
optional Univex
attach­ments.

#12 PTO POWER DRIVE UNIT

MADE IN THE USA

ELECTRICAL: 115V-230V, 60Hz. Single Phase

MOTOR: 1 HP Capacitor start 1725 RPM, ball bearing motor on cushioned supports for reduction

of both noise and vibration.

SWITCH: Rocker type double pole on-off conveniently located for access from the front or left

side. Has a removable operator key to prevent unauthorized operation. .

CORD and PLUG: 5ft (1524mm) long 3-wire, 16 gauge SJTO cord with a polarized molded plug.
DRIVE: 7:1 Reduction increases torque using a 10 ribbed Poly “V” belt. 250 RPM drive shaft

supported by ball bearings in the P.T.O. Housing..

DRIVE ASSEMBLY: Completely enclosed in an acrylic urethane silver enamel finished 10 gauge steel

housing and No. 4 finish 20 gauge stainless steel cover.

WEIGHT: Net 85 lbs. (38kg), shipping 95 lbs. (43Kg).

CUBE: 5.8 cu. ft. (16 cu m)

OPTIONAL ATTACHMENTS:

NOW EQUIPPED WITH A 1 H.P. MOTOR!

PM91

SPECIFICATIONS

PM91

April 2005

Printed in USA

PREP

MATE

UNIVEX CORPORATION ■3 Old Rockingham Road ■Salem, NH 03079-2140

Tel [phone] ■Fax [phone] ■E-mail [e-mail]

TOLL-FREE ORDERING FAX [phone]

www.univexcorp.com

SINCE 1948

VS9-H

Shredding/Grating

Housing (same as VS9)

• H& S - Hub and Shaft

• Your Choice of Plates
1/2" (13mm) shredder Plate
5/16" (7mm) shredder Plate
3/16" (4mm) shredder Plate
3/32" (2mm) shredder Plate
Universal Grating Plate

VS9

Vegetable Slicing

Housing (same as VS9-H)

• Adjustable stainless steel
“S” Knife Assembly

ALMFC12

Meat & Food Chopper

• #12 Aluminum Grinder
Attachment with 3/16"
(4mm) Plate holes*

• Stainless Pan
12 3/4" *(324mm) Long x 10 3/8"
(257 mm) Wide x 2 1/2" (64 mm) Deep

•USDA/NSF Stomper

*Optional plate sizes are available

22"

559 mm

33"

838 mm

1/2

17

44 mm

"