INSTRUCTION
PM91
WE
THANK YOU
FOR YOUR PURCHASE OF OUR MODEL
MANUAL H/D PREP-MATE
PM91 H/D PREP-MATE
PM911960001 ED3
UNIVEX H/D PREP-MATE
Mate drive assembly has been inspected and tested at the
PARTS LIST
1 8700101
Housing
1 2
8700014
Foam, Rubber Strip
2 3
8700002
Cover, Housing
1 4
4400141
Nut, Kep
1/4-20 4 5 1200075
Washer, Steel Flat
1/4 7 6 8700103
Clip, Tub
1 7 RESERVED
8 8700104
Feet 4 9 1030019
Ball Bearing 6204
LL 2 10
RESERVED
11 4400072
Set Screw
5/16-18x3/8
2 12
8800010
Shaft, P T
0 1 13 4400230
Key
3/16
Square
2 14
1200117
Retaining Ring Int.
1 15
1200119
Retaining Ring Ext
2 16
8700025
Pulley, Driven
1 17
8700010
Belt, Drive 300J10
1 18
120002
5
Screw, Hex HD
1/4-20 x 3/4 3 19 4400005
Lockwasher
1/4 5 20 8700035
Switch, With Key
1 21
8700034
Key, Switch (Key only)
1 22
8700019
Knob Assembly, P T
0 1 23 4400045
Housing, P T
0 1 24 8800012
Adaptor, P T
0 1 25 1200412
Set Screw
1/4-20 x
1/4 2 26 1200440
Bolt,
10-32 x 1 1 27 8700024
Pulley, Drive
1 28
4400155
Screw, Hex HD Cap,
1/4-20 x 2 29
8700105
Tub & Cover (NOT SHOWN)
1 30
1200012
Screw, Phil HD
10-32 x 1/2 6 31 4400414
Washer, Flat
1/4 4 32 8700026
Spring, Compression
2 33
4400415
Sleeve (Long)
2 34
1200411
Screw, Hex HD
1/4-20x2 2 35 1200413
Screw, Hex HD
1/4-20 x 1 1/2
2 36
4400516
Sleeve (Short)
2 37
8700032
Spacer, Isolator
4 38
4400398
Cable Tie
3 39
1012042
Strain Relief
1 40
8800100
Cord, Electric 115V
1 8800100
-
Cord, Electric 220V
1 41
4400351
Label, Stop Unplug (Not
1 42 1031307
Motor,
1
HP, 115V230V,
60
HZ 1
1031309
Motor,
1
HP, 220V,
50
HZ 1 43 4400417
Sleeve, Spring
2 44
1024010
Label, Univex (Not Shown)
1 45
1200060
Nut, Hex
10-32 3 46
4400065
Lockwasher,
#10 2 49 1200442
Screw, 10
-
32X 1/2 ThussHead
2
40 8800100
-1
Cord. Electric!
15 V 1 47 4400249
Circuit Breaker
1 48
4400227
Label, Rese
t (Not Shown)
1
INSTRUCTION MANUAL
The UNIVEX PM91 is a 1 HP portable electric unit consisting of a
poly "V" belt assembly with a No. 12 drive hub operating at 250
rpm. It is designed to support and power the UNIVEX MFC12 Meat
and Food Chopper, VS9 Vegetable slicer, and the VS9H Shredder
and Grater food processing attachments. A 20 quart container, with
cover, is supplied for food collection and storage.
INSPECTION
The Prepfactory; however, it should be externally inspected and electrically
checked prior to use. The electrical data listed on the nameplate
should be the same as the user's electrical supply. Any damage
should be reported to the carrier immediately, and any shortage or
deviation of parts to UNIVEX Corp.
ITEM
NO.
P ART
NO.
DESCRIPTION QTY
.
SAFETY
The user should read and understand the H/D Prep-Mate and the
attachment instructions prior to operation. First time operators
should be properly trained in safety precautions and in the proper
use and servicing of this equipment and attachments. Switch the
power "OFF" and disconnect the electrical supply before mounting
or disengaging an attachment, or for cleaning and servicing the
equipment. Before, connecting unit to power source it should also
FOR CSA ONLY.
If the circuit breaker is actuated, turn the power switch to "OFF,"
and disconnect the electrical supply, determine and then correct the
fault before resetting. To prevent unauthorized use, remove the
switch key.
H/D PREP-MATE
(Assembly Drawing)
FOR CSA ONLY
ITEM
PART NO. DESCRIPTION QTY
NO.
.
Be sure the attachment is properly cleaned, assembled, and installed,
is properly installed on the drive shaft. The
turn power to "OFF" and disconnect power source. Remove the attachment,
Adjustable "S" knife assembly with hardened stainless steel
000
0
3
7
COLORING
tighten thumb screw before connecting to power source. Do not attempt to
service the drive assembly. Please contact Univex Corp. for the number of
the nearest authorized service agent in your area.
OPERATION
The Prep-Mate should be set-up in an area that is convenience for
operation, and has sufficient clearance for safety. Before installing PTO
attachment,
VEGETABLE PREPARATION ATTACHMENTS
make sure the adaptor (Item 24)
PTO should be attached with a twisting motion and in an upright position.
Make sure to tighten the thumb screw . When processing foods please
observe operating and safety instructions. When processing is completed,
disassemble, clean, dry and sanitize before storing in a clean, dry
environment.
STANDARD EQUIPMENT
Satin finish anodized aluminum housing with.
hinged feed chute door, latch and feed pusher
knife and #12 rear hub.
THE VERSATILE VS9 IS USED FOR SLICING: OPTIONAL: SHREDDER AND GRATER PLATES
LETTUCE COLE SLAW
CUCUMBERS PEPPERS
CARROTS HOME FRIES
CELERY CHINESE VEGETABLES
Approximate shipping weight — 20 lbs.
STANDARD EQUIPMENT
Satin finish anodized aluminum housing with
hinged feed chute door, latch and feed pusher.
Die cast aluminum hub with stainless shaft
and #12 rear hub and stainless locking pins.
AND TYPICAL USAGES
1/2"
FOOD
PRODUCT
COLE SLAW •
BREAD
CRUMBS
CHEESE
SOFT CHEESE
FOR PIZZA
CARROTS FOR
CHEESE FOR
TACOS
HARD CHEESE
SHREDDER
PLATE
5/16"
SHREDDER
PLATE
3/16"
SHREDDER
PLATE
•
•
3/32"
SHREDDER
PLATE
•
• •
•
UNIVERSAL
GRATER
PLATE
14
•
•
Loading...