Univex MG22 Parts List

Page 1
INSTRUCTION MANUAL
Meat Grinder
Persons under age 18 are not permitted to operate
have accessibility to operate this equipment
or
per
Administration Fact Sheet No. ESA91-3.
univex
MG22/0603
PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor
ED 3
Page 2
TO
INSURE
BOTH
SAFE
AND
TROUBLEFREE PERFORMANCE WE STRESS
THAT ALL
PERSONNEL
THAT
WILL
BE
INVOLVED WiTH YOUR NEW UNIVEX MEAT
GRINDER MUST READ AND UNDERSTAND
THESE INSTRUCTIONS BEFORE ATTEMPTING
TO OPERATE THIS UNIT.
WE APPRECIATE YOUR COOPERATION AND
YOUR BUSINESS.
SHOULD THERE BE A
QUESTION OR IF WE CAN BE OF FURTHER
ASSISTANCE,
PLEASE
CALL
US,
I 6O3-893-61 91.
PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor
Page 3
TABLE OF CONTENTS
DESCRIPTION
Table of Contents
Operator Safety Installation
Assembly and Operating Instructions
Cleaning Parts List
Assembly
Wiring Diagram 115/208-230V, 60HZ, IPH /
Wiring Diagram, Canada, CE, 115/208-240V, 60HZ, IPH /
Warranty Information
220-240V, 50HZ, IPH
230V,50HZ, IPH
MG22 MEAT GRINDER
INSTRUCTION MANUAL
Inspection:
All Univex MG22's are inspected prior to packaging
inclusion of options, and proper voltage. However,
verified that they are correct, Any damage, imperfection,
to your dealer or directly to Univex Customer Service, and/or shipment
to assure both the machine quality, correct
upon unpacking, all items should be carefully
or shortages should be reported immediately
Operator Safety:
It is a violation of the United States Department of Labor
the MG22 by any person under the
age of 18 years.
regulations to permit operation of
MG22
PAGE
2
2 -3
3
4 - 5
6
7
8
Back Cover
carrier.
Read and understand all instructions and safety warnings
Never put fingers or any utensils (other than the
grinder, or in the kniíb and plate area of the grinder. This
meat; use extreme caution and avoid exposing body parts
Switch the power off and disconnect the electric
the grinder, cleaning, or servicing.
prior to operating unit.
stomper (Item 10) in the throat or entry of the
is a powerThl unit designed to grind
to grinding and cutting areas of the unit.
power supply prior to mounting and dismounting
Knife is sharp and can cut finger. Use caution when handling.
Always have chopper securely mounted,
knife, plate, and ring snugged on before switching the
Always remove the grinder from the power drive before
mounted to power source, inviting electrical shock.
PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor
worm assembly fully coupled onto drive coupling, and the
power on.
cleaning; never rinse with hose while
Page 1
Page 4
Installation;
MG22
This is a table-top unit. Unit may be secured to table top via the shipping bolt threaded holes
power drive housing bottom.
Insure the unit is located such that it is placed on a level and stable surfàce, and sufficient clearance
is provided all around the unit for safrty and ease of operation. Proper location includes space for
the feed pan and clip-on storage container,
Feed pan support bracket (Item 45) must be assembled onto the housing cover (Item 43) using the
screws (Item 46) provided.
on the
ASSEMBLY AND OPERATING INSTRUCTIONS;
Introduction:
The Univex MG22 Meat Grinder consists of a I H.P. electric motor power base which drives a bell-shaped meat grinder designed to utilize industry standard #22 knives and full range of #22 grinding plates. Included as standard equipment is a carbon steel knife (Item 3), 3/16 grinding plate (Item 2), aluminum meat stomper (Item 10), 16 x 24 aluminum feed pan (Item 9) for holding meat to be processed, and t8.5 x 13.5 storage container with lid för collecting meat as it is processed.
The Univex MG22 has safety and ease of operation built into it. The permanent safety guard positioned
over the bell-shaped feed hopper prevents accidental entry of operator's fingers and hands into the
grinding zone, The readily removable feed pan and storage container provide for ease of processing and
cleaning.
Noise emissions below 70 db(A).
Assembly:
WARNING: Disconnect power supply prior to assembly.
Mount the housing-guard assembly (Item 8) to the housing weldment (Item 26) by firmly
tightening knobs (Item 12) onto mounting studs (Item 14).
Slide the worm assembly (Items 6,5,4) into the housing-guard assembly (Item 8) and mating into
the drive coupling (Item 15).
Slide the knife (Item 3), sharp edges toward the plate, onto the square of the worm assembly (Item
4). Slide the plate (Item 2) onto the worm assembly (Item 4). Screw the ring (Item 1) onto the
housing-guard assembly (Item 8) until it is just snug. Too much pressure can damage the unit.
WARNING: The knife is sharp and can cut fingers.
Guide the feed pan (Item 9) over the guard portion of the housing-guard assembly (Item 8) onto
the pan stud (Item 7) and the pan support (Item 44).
S. Locate the storage container under the clip (Item 24) and resting on the front legs (Item 23).
6. Connect power supply and actuate power switch (Item 25).
WARNING: Never put fingers or utensils in the throat of the grinder or the knife and
plate interface.
Page 2
PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor
Page 5
Process
MG22
Cut meat to be processed to fit under or through the safety guard. Recommended size
x 3" wide x 12" long. Set meat in pan (Item 9).
With grinder running, slide product under the guard of the housing-guard assembly
through the openings in the guard top. Use the meat stomper (Item 10) if desired,
product into grinding zone. The stomper is recommended for regrind.
Collect ground product in storage container,
Cleaning:
Turn unit off and disconnect from power supply.
Disassemble unit in reverse of assembly instructions
then ring, plate, knife, worm assembly, and housing-guard assembly.
- Remove storage container, feed pan, and
WARNING: The knife is sharp and can cut fingers.
Clean components including the drive coupling (Item 15) by following the
sanitize, and air dry. Use the bristle brush provided to clean areas diflicult
procedure: wash, rinse,
small amount of food grade lubricant to bronze bushing, located inside the housing-guard assembly (item 8), before use.
is 1
'/2'
(Item 8) or
to guide
to access, Apply a
thick
Page 3
PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor
Page 6
ILLUS.
3
4
5
6
7
8
9
10
11
12
13
14
15
16 17
18
19
20
21
22
23 24 25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
1
2
PART NO.
1000719
1000727
1000726
1000728 1000729
1000730
1000725
1000715
1000711
1000717
1000731 *
1000709 *
8700214 1000735
1000724
8700222
4400275
1000718 1000713 1200412
1200359
1000722
4400500
4400015 8700219 8700220
8700211
8700216 8700218 8700210
1200432
7100103
7100023
1024414
1200433
1200076
4400065
1200060
7510252
7100011
7100015
7100012
7 100040
7100116
7100108 7100016
7100010
4400155
4400005
1814118**
8512855
DESCRIPTION
ASSEMBLY
RING,#22
PLATE, 3/16"
PLATE 1/8' (OPTIONAL)
PLATE 1/4' (OPTIONAL) PLATE 3/8' (OPTIONAL) PLATE 1/2' (OPTIONAL)
KNIFE, #22
ShAFT, FRONT
WORM, #22 COUPLING, WORM
STUD, PAN
ROUSING-GUARD ASSY
PAN
STOMPER LOCK PIN, PLATE
KNOB
STUD - SWITCH ACTUATOR STUD, MOUNTING COUPLING, DRIVE
SETSCREW 1/4-20X1/4CUppT
SCREW HEX. RD. SS CAP 3/8-16 X 1 1/2" LOE
WASHER, MOTOR
KEY 1/4SQ.X1 1/2
KEPNUT
3/8-16
GEAR MOTOR
SLEEVE,
LEG,
FRONT LEG
FRONT
CLIP, BUSS BOX SWITCH, START/ STOP
HOUSING, WELDMENT
SCREW HEX. RD. CAP 4-40 X 3/4 LOE
SWITCH, SAFETY
INSULATOR, SAFETY SWITCH BRACKET, SAFETY SWITCH
ELASTIC STOP NUT
4-40
WASHER 10
LOCK WASHER 10
HEXNUT1O-32
ELASTIC STOP NUT - MIO X 1.5
CONTACTOR
115V, 60HZ.
CONTACTOR 100V, 50-60HZ
CONTACTOR
230V, 60HZ
STARTER, 115V, 60HZ (CANADA ONLY)
STARTER, 230V, 60HZ, (CANADA ONLY)
STARTER, 230V, 50HZ, IPH
CONTACTOR,
220-240V, 50HZ,
(EUROPE ONLY)
RAIL, DiN
SCREW HEX. RD. CAP 1/4-20 X 1/2 LOE
LOCK
WASHER 1/4
LEG,REAR
FEET, REAR
Page 4
MG22
QTY.
2
2
2 6
I
8
2 2
I
2
1
I
2
6
6
7
2
1
I
2
2 2
2
PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor
Page 7
ILLUS.
42 43
44
45
46
47
48
49 50
51
52
53
54 55
56 57
PART NO.
7100107
8700212 8700215 8700217
4400246
1200012
8700014 8700105
8800200
8800208
4400326
4400351
1000732
4400401
8800229
DESCRIPTION
STRAIN RELIEF
COVER, HOUSING
SUPPORT, PAN
SLEEVE, PAN SUPPORT
SCREW, FLAT RD SLT SS 10-32 X 3/4
SCREWPPHD.10-32X1/2LG.
RUBBER STRIP
STORAGE CONTAINER (NOT SHOWN) POWER CORD (NOT SHOWN)
CORD, MOTOR (NOT SHOWN)
LABEL, UNIVEX (NOT SHOWN) LABEL, (NOT SHOWN)
RESERVED
BRUSH, CLEANING (NOT SHOWN) CONNECTOR. 3/8 (NOT SHOWN) WIRING PKG. (NOT SHOWN)
* ILLUS. NO. 71S INCLUDED WITH ILLUS. NO 8
** ILLUS. 40 INCLUDES STUD M10-1.5 X 22MM
MG22
QTY.
1
2
2
6
1
1
Page 5
PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor
Page 8
PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor
Page 9
SAFETY
SWITCH
PART
NUMBER
8800229
8800208
r
L
W2
STOP
PWTCH
I
I,,
L,._ J
WIRING DIAGRAM
115/208-230V, 60HZ, IPH
220-240V, 50HZ, IPH
WI
J. MAGNETIC
CONTACTOR
START
SWITCH
,I
WIRE
NO.
WI
W2
W3
W4
W5
we
W7
W8
I
W3
LI
I..
o-f----
WIRE
GA
SEE
NOTE
5
3 33
16
3 13
IS
3
6
3
IS
3
IS
3 2
16
3
MOTOR CORD
/
BLACK WI-tIE GND
W4
ABLE
LENGTH
l4 INCHES
2 (/2 1
24
25
(/2
2 (/2
POWER N
W8
END A
SEE NOTE
- I
I
1
I
I
I
L3cr
W7
W5
4,
I3h]
END B
SEE NOTE
2
2
I
I
I
I
I
14 I
-J
MOTOR
COLOR
WHITE WHITE
RED
BLACK
RED RED
RED
MG22
NOTES:
I. DOUBLE CRIMP FERRULES, KLAUKE 72/IOVZ
MOLEX-ETC BB-5623.
OR AMP 925553-2,
MATERIAL: I6GA 1015 TEW CSA AND UL APPROVED.
IMPORTANT; Before making electrical connections, check the
(located on the rear panel) to assure they agree with those of
WA.RNJNG: Whenever maintenance is being performed,
DISCONNECT electrical cord and place a tag on it indicating the slicer is being
specifications on the data plate
your electrical service.
or whenever the top cover has been removed,
worked on.
Page 7
PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor
Page 10
WIRING DIAGRAM
CANADA & CE
115/208-240V, 60HZ, IPH
230V, 50HZ, 1PH
/ I
WI
W6
POWER IN
L2 L3 ONO
LI
W8
9
-
OVERLOAD RELAY
SAFETY
SWITCH
NOTES:
LI
L2
TI
T2°T3\,0
S
13
L3
-
14
r
STARTER
i
AI
A2
JD .-O _95
TI
L_ _..J
W7
W2
STOP
SWITCH
I I
H..
W3
.1
PART
NUMBER
8800229
PART
OF
STARTER
8800208
I, DOUBLE CRIMP FERRULES. KLAUKE 72/IOVZ OR AMP 925553-2
MOLEX-ETC BB-5623.
MATERIAL:
W4
START
SWITCH
\
o
WIRE
GA SEE
NO.
WI 16
W2 6 3
W3
16
W4
WS
W6
W7 16
WI
WO
6 6
16
16
MOTOR CORD
W5
NOTE
3
3 2 3
3 3
3 5
3 8
W9
WIRE TABLE
LENGTH
IN INCHES
33
13
1/2
24
26
1/2
2
1/2 I
1/2
END A
SEE NOTE
I6GA 1015 TEW OSA AND UL APPROVED.
MOTOR
END B
SEE NOTE
I I 2
I
I I
I I
I
I
'COLOR
2 WHITE
WHITE
I
BLACK
I
I
I
RED
RED RED RED
RED
IMPORTANT: Before making electrical connections, check the specifications on the data plate
(located on the rear panel) to assure they agree with those of your electrical service.
WARNING; Whenever maintenance is being performed, or whenever the top cover has been removed,
DISCONNECT electrical cord and place a tag on it indicating the slicer is being worked on.
Page 8
PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor
Loading...