All Univex MGOO12's are inspected prior to packaging to assure both the machine quality,
inclusion of options, and proper voltage. However, upon unpacking, all items should be carefully
correct
verified that they are correct. Any damage, imperfection, or shortages should be reported immediatelyto your dealer or directly to Univex Customer Service, and/or shipment carrier.
Read and understand all instructions and safety warnings prior to operating unit.
Operator Safety:
For safety, a small padlock (available at any hardware store) may be passed through the switchguard (Item 22) to positively secure the switch after it has been moved to the "off' position.Never put fingers or any utensils (other than the stomper (Item 35) in the throat or entry of the
grinder, or in the knife and plate area of the grinder. This is a powerful unit designed to grind
meat; use extreme caution and avoid exposing body parts to grinding and cutting areas of the unit.Switch the power off and disconnect the electric power supply prior to mounting and dismountingthe grinder, cleaning, or servicing.
Knife is sharp and can cut finger. Use caution when handling.
Always have chopper securely mounted, worm fully coupled onto drive shaft, and the knife, plate,and ring snugged on before switching the power on.
Always remove the grinder from the power drive before cleaning; never rinse with hose while
mounted to power source, inviting electrical shock.
Be aware if the electrical supply to the MGOO12 is disconnected, but the switch is left in the "on"position, the MGOO12 will start when the electrical supply is reconnected, To safety power down
the MGOO12, move the switch to the "off' position, then disconnect the electrical supply.
This is a table-top unit,Insure the unit is located such that it is placed on a level and stable surface, and sufficientclearance is provided all around the unit for safety and ease of operation. Proper location includes
space for the feed pan and collection container.
ASSEMBLY AND OPERATING INSTRUCTIONS:
Introduction:
The Univex MGOO12 Meat Grinder consists of a 1/2 H.P. electric motor power base which drives
meat grinder designed to utilize industry standard #12 knives and full range of#12 grinding plates.Included as standard equipment is a carbon steel knife (Item 29), 3/16 grinding plate (Item 28), meatstomper (Item 35), and stainless steel feed pan (Item 34) for holding meat to be processed.
Assembly:
WARNING: Disconnect power supply prior to assembly.
Mount the chopper-housing (Item 33) to the power takeoff by inserting and rotating counter
clockwise until the chopper stops in the vertical position.
Slide the worm (Item 31) into the chopper housing, (Item 33 ) rotating the worm until the rear slot
engages with the drive shaft.
Installation:
PAGE i
a
PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor
WARNING: The knife is sharp and can cut fingers.
MGOO12
Slide the knife (Item 29), sharp edges outward, onto the
appropriate plate (Item 28) onto the worm (Item 31) and into the housing aligning slotScrew the ring (Item 27) onto the chopper housing (Item 33) until it is just
pressure can damage the unit.Insert the feed pan throat (Item 34) into the chopper housing.Arrange for a container to receive the ground product.
square of the worm (Item 30). Slide the
WARNING: Never put fingers or utensils in the throat of the grinder
plate interface.
Process:
Cut meat or other products to be processed to fit into the chopper, and place
Connect power supply and actuate power switch (Item 20).
Use the meat stomper if desired, to guide product into grinding
recommended for regrind.
3. Collect ground product in storage container.
zone. The stomper is
Cleaning:
Turn unit off and disconnect from power supply.Disassemble unit in reverse of assembly instructions
then ring, plate, knife, worm, and chopper housing.
-- Remove storage container, feed pan, and
WARNING: The knife is sharp and can cut fingers.
Clean components including the drive shaft which is part of Item 7, by
wash, rinse, sanitize, and air dry. Apply a small amount of food grade
portion of worm.
Repair
Always Disconnect Machine from Electrical Supply Before Servicing.
Remove 2 screws (item 43) from front of base (item 18).Lift motor/gear box assembly (item 17) from base (item 18) by removing
(item 45)
Disconnect motor cord from switch (item 20) and capacitor cord from
Warning Capacitor may store electrical charge. Discharge with insulateddriver or similar insulated device.
snug. Too much
with pin.
or the knife and
in feed pan.
following the procedure:
lubricant to the rear shaft
two screws
capacitor.
screw
2. Gear Box RepairA
Remove 4 screws (item 25) from PTO housing (item 4).Pry PTO housing (item 4) away from front of motor (cork gasket (item
replaced before reassembly).
Remove retaining ring (item 1) and slide output gear! shaft (item 7) from
(item 4).
Remove as much grease as possible with a cloth and reapply
reassembling gear box. (Do not use solvents to clean plastic parts.)
Inspect all gears, bushings, seals, and shafts for wear and replace where
Reassemble in reverse order.
PAGE 2
PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor
new grease before
11) should be
PTO housing
necessary.
Illus.
io.
i 1.
i4.
15.
i6.
17.
22,
23
24
3i.
43
44
*5
Part No.
8700410
870041 i
8700412
8700413
87004i4
8700415
87004i6
8700417
87004i8
87004198700420
1204009
870042i
65090458700423
i204010
8700424870042587004268700427
7i20009
8700450
71200118700431
8700432
1204011
8700433
8700434
i000509
1000508
1000510
1000511
10005 12
1000506
8700435
87004368700437870043887004398700440
i0005 13
10005148700441
8700442870044387004448700445870044687004478700448
1204012
8700449
85i262i
1200092
ASSEMBLY
Figure 1
Description
Retaining Ring, External
Shim. Washer
Washer, Nylon
PTOHousing
Bushing, Flanged PTO
O-ring,
Gear, Output Set
Bushing, Flanged, Output GearBushing. Flanged, Oil Seal
Seal,V-RingOil
Gasket, Gear BoxScrew, Hex HID Washer M6 X 1.25 X 8mm Zinc Plated
Cover, Top
HandlePanel, Rear
Screw SS Phil HID Self Tappmg 3.9 x 9.5mm
Motor 115V/6OHZ/iPH
Motor 220V/5OHZ/1PH
BaseFeet, Rear Rubber
Switch (with mounting hardware)
Sleeve, Vinyl Leg
Guard, Switch
Bushing, Flanged, Step GearPin, Chopper Mounting
Screw, Soc, HID. Cap MS X 0.8 X 20MM 1g.
Pin, Plate Locating
Ring, ChopperPlate, 3/16 Standard
Plate, i/8 Optional
Plate, 1/4 Optional
Plate, 3/8 Optional
Plate, 1/2 Optional
KnifeShaft, FrontWorm Assy (Includes Illus 30 and 32)Washer, Thrust
Housing, Chopper
Pan
Stomper
Sausage Stuffer i/2 Optional
Sausage Stuffer 3/4 Optional
Capacitor, i 15V only (not shown)Capacitor, 220V only (not shown)
Cord, Power, 115V only (not shown)
Cord, Power, 220V only (not shown)
Cord, Motor (not shown)Cord, Capacitor (not shown)Strain Relief, Power Cord (not shown)Strain Relief Motor Cord (not shown)Screw SS Phil HD M5-0.8 X 15MM
Bracket, Motor
Screw M4Washer, Flat no. 8
PAGE3
MGOO12
Q
i
ii
ii
ii
iii
i
3
iii
4
i
i
2
i
2
i
i
4
i
i
i
1
i
i
i
ii
i
i
i
1
1
i
iii
4
i
2
2
PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor
(fj
PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor
POWER IN
/
MGOO12
WRUNG DIAGRAM
MODEL MGOO12
ll5V,6OHZ, 1PH
220-240V, 50HZ, 1PH
CORD
CAPACITOR
BLU E
BLACK
MOTOR
SWITCH
BLACK
WHITE
GREEN
IMPORTANT: Before making electrical connections, check the specifications on the
data plate (located on the rear panel) to assure they agree with those of
your electrical service.
WARNING: Whenever maintenance is being performed, or whenever the top cover has
been removed, DISCONNECT electrical cord and place a tag on itindicating the grinder is being worked on.
BROWN
BROWN
GREEN/YELLOW
PAGE 5
PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.